Hirose DF14-3P-1.25C 1.25mm pitch super low profile crimping connector Datasheet

1.25mm Pitch Super Low profile Crimping Connector
DF14 Series
■Features
1. Super Low Profile
This is a connector special for right angle which has pursued a low
profile on the board.
Board mounting height: 2.5mm
A signal can be fetched from the area where there is no board to
board space.
Board Mounting Figure
2. Correspond to Automatic Mounting
The header has the vacuum mount face which enables the vacuum
absorption and the automatic mounting by the embossed tape
packaging.In addition, the tube packaging can be selected.
3. Four Wall Type Without Friction to Board by Socket
The header has the box structure to prevent from being twisted and
has the perfect mis-insertion prevention method. Moreover the
header has the wall on the board side and doesn't have any trouble
resulted from the friction to board by socket.
In addition, the metal fitting is attached to prevent the solder peel.
1
■Applications
LCD, Note PC, Mobile Terminal Small business equipment, Video camera
B177
■Product Specifications
Current rating
Rating
1A
Operating Temperature Range-25 to +85ç (Note 1)
Voltage rating 150V AC Operating Moisture Range
Item
Storage Temperature Range -10 to +60ç (Note 2)
40 to 80%
Storage Moisture Range
Specification
40 to 70%
Condition
1. Insulation Resistance
500M ohms Min
100V DC
2. Withstanding voltage
No flashover or insulation breakdown.
500V AC/1 minute
3. Contact Resistance
30m ohms Max
100mA
4. Insertion/Extraction Force MIN0.15N (15gf), MAX3N (300gf)
Measure at the square steel pin of 0.3±0.002mm
5. Vibration
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions.
No electrical discontinuity of 1µs or more
6. Humidity (Steady state) Contact resistance: 30m ohms Max Insulation resistance:500M ohms Min
7. Temperature Cycle
96 hours at temperature of 40ç and humidity of 90% to 95%
(-25ç: 30 minutes➝5 to 35ç: 10 minutes➝85ç: 30 minutes➝
Contact resistance: 30m ohms Max Insulation resistance: 500M ohms Min
5 to 35ç: 10 minutes) 5 cycles
8. Durability (Mating/un-mating) Contact resistance: 30m ohms Max
9. Resistance to Soldering heat
Tin plating: 30 cycles Gold plating: 50 cycles
Reflow: At the recommended temperature profile
No deformation of components affecting performance.
Manual soldering: 300ç for 3 seconds
Note 1: Includes temperature rise caused by current flow.
Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and
Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation.
■Material
Product
Part
Crimping Socket
Insulator
Crimping Contact for Socket
Contact
Insulator
Contact
Fitting
Pin Header
Material
Finish
Remarks
Polyamide
Beige
UL-94V-0
Phosphor Copper
Tin-lead plated or gold plated
–––––––
Polyamide
Beige
UL-94V-0
Brass
Tin-lead plated or gold plated
–––––––
Phosphor copper
Tin-lead plated
–––––––
Note . Hirose’s tin plating product takes measures against whisker.
■Ordering Information
●Connector
DF14
1
- * S - 1.25 C
2
3
4
5
1
Series Name: DF14
4
Contact Pitch: 1.25mm
2
Number of Contacts: 2 to 10, 15, 20, 25, 30
5
Contact Type
3
Connector Type
C: Crimping socket
S: Single row socket
H: Right angle SMT
P: Single row pin header
●Contact
DF14 - 2628 SCF A
1
1
Applicable cable size
2
2
2628: AWG26 to 28
3032: AWG30 to 32
3
Packaging Type
SCF: Socket contact/reel
3
Plating Type
Blank: Tin plated
A: Gold plated
B178
■Crimping Socket
Photo: Contact insertion state
Unit: mm
Part Number
DF14- 2S-1.25C(**)
DF14- 3S-1.25C(**)
DF14- 4S-1.25C(**)
DF14- 5S-1.25C(**)
DF14- 6S-1.25C(**)
DF14- 7S-1.25C(**)
DF14- 8S-1.25C(**)
DF14- 9S-1.25C(**)
DF14-10S-1.25C(**)
DF14-15S-1.25C(**)
DF14-20S-1.25C(**)
DF14-25S-1.25C(**)
DF14-30S-1.25C(**)
CL No.
538-0005-8-**
538-0006-0-**
538-0007-3-**
538-0008-6-**
538-0009-9-**
538-0010-8-**
538-0011-0-**
538-0013-6-**
538-0014-9-**
538-0054-3-**
538-0059-7-**
538-0064-7-**
538-0012-3-**
Number of Contacts
2
3
4
5
6
7
8
9
10
15
20
25
30
A
4.45
5.70
6.95
8.20
9.45
10.70
11.95
13.20
14.45
20.70
26.95
33.20
39.45
B
1.25
2.50
3.75
5.00
6.25
7.50
8.75
10.00
11.25
17.50
23.75
30.00
36.25
[Specific No.]–**,(**)
Blank : 1 bag 100 pcs.
Note 1.The quantity at the specific No. "Blank" is delivered per bag. If needed, please order the products per bag.
■Socket Crimping Contact
Part Number
DF14-2628SCF
DF14-3032SCF
CL No.
538-0001-7-**
538-0003-2-**
Packaging Type
Reel
Reel
KApplicable Cable (Tin plating Annealed copper wire)
Conductor Size (Wire construction)
AWG26(7 cores/0.16mm)
AWG28(7 cores/0.127mm)
AWG30(7 cores/0.1mm)
AWG32(7 cores/0.08mm)
Jacket Diameter
Ø0.54 to Ø1mm
Quantity
Finish
10,000
Tin plated
KRecommended Cable
UL1571
KStrip Length
1.2 to 1.9mm
Note:If other cables are used instead of the applicable cable, contact Hirose
sales department.
BApplicable Crimping Tool
Type
Applicator
Press Main Unit
Manual Crimping Tool
Part Number
AP105-DF14-2628S
AP105-DF14-3032S
CM-105
DF14-2628/CR-HT
DF14-3032/CR-HT
CL No.
901-4548-1
901-4544-0
901-0005-4
550-0261-1
550-0262-4
Applicable Contact
DF14-2628SCF/SCFA
DF14-3032SCF/SCFA
--------------------------------------------DF14-2628SCF/SCFA
DF14-3032SCF/SCFA
Note 1.If a trouble has occurred due to tools, which are not designated by Hirose, Hirose won't guarantee any product.
Note 2.Use the reel contact sequentially cut for manual crimping tool.
B179
■Right Angle Pin Header (SMT)
Note 1."Without boss" indicates the style with no boss.
BPCB mounting pattern
BTube Packaging Dimensions
[Specific No.]–**,(**)
(20): Tin plated tube packaging
(21): Tin plated embossed tape packaging
(50): Gold plated tube packaging
(59): Gold plated embossed tape packaging
Note 2."Without boss" indicates that no hole is needed.
Unit: mm
With boss
Part Number
Without boss
CL No.
Part Number
Tube Packaging
CL No.
Number of Contacts
A
B
C
D
DF14- 2P-1.25H(**)
538-0021-4-** DF14A- 2P-1.25H(**) 538-0033-3-**
2
7.45
1.25
6.45
8.05
66
DF14- 3P-1.25H(**)
538-0022-7-** DF14A- 3P-1.25H(**) 538-0034-6-**
3
8.70
2.50
7.70
9.30
56
DF14- 4P-1.25H(**)
538-0023-0-** DF14A- 4P-1.25H(**) 538-0035-9-**
4
9.95
3.75
8.95
10.55
49
DF14- 5P-1.25H(**)
538-0024-2-** DF14A- 5P-1.25H(**) 538-0036-1-**
5
11.20
5.00
10.20
11.80
44
DF14- 6P-1.25H(**)
538-0025-5-** DF14A- 6P-1.25H(**) 538-0037-4-**
6
12.45
6.25
11.45
13.05
39
DF14- 7P-1.25H(**)
538-0026-8-** DF14A- 7P-1.25H(**) 538-0038-7-**
7
13.70
7.50
12.70
14.30
36
DF14- 8P-1.25H(**)
538-0027-0-** DF14A- 8P-1.25H(**) 538-0039-0-**
8
14.95
8.75
13.95
15.55
32
DF14- 9P-1.25H(**)
538-0028-3-** DF14A- 9P-1.25H(**) 538-0040-9-**
9
16.20
10.00
15.20
16.80
30
DF14-10P-1.25H(**)
538-0029-6-** DF14A-10P-1.25H(**) 538-0041-1-**
10
17.45
11.25
16.45
18.05
28
DF14-15P-1.25H(**)
538-0084-4-** DF14A-15P-1.25H(**) 538-0114-3-**
15
23.70
17.50
22.70
24.30
20
DF14-20P-1.25H(**)
538-0089-8-** DF14A-20P-1.25H(**) 538-0119-7-**
20
29.95
23.75
28.95
30.55
16
DF14-25P-1.25H(**)
538-0094-8-** DF14A-25P-1.25H(**) 538-0124-7-**
25
36.20
30.00
35.20
36.80
13
DF14-30P-1.25H(**)
538-0020-1-** DF14A-30P-1.25H(**) 538-0045-2-**
30
42.45
36.25
41.45
43.05
11
Note 1.Please order the tube packaging product, multiplying the packaging quantity (pcs.).
Note 2.Please order the embossed tape packaging product according to reel number. (1000 pcs./reel)
B180
Quantity
BEmbossed Carrier Tape Dimensions
■ 2 to 10 Contacts
■ 15, 20, 25, 30 Contacts
Unit: mm
Inserted Connector
Number of Contacts
A
B
C
D
DF14/14A- 2P-1.25H
2
16
7.5
16.4
–
–
–
DF14/14A- 3P-1.25H
3
16
7.5
16.4
–
–
–
DF14/14A- 4P-1.25H
4
24
11.5
24.4
–
–
–
DF14/14A- 5P-1.25H
5
24
11.5
24.4
–
–
–
DF14/14A- 6P-1.25H
6
24
11.5
24.4
–
–
–
DF14/14A- 7P-1.25H
7
24
11.5
24.4
–
–
–
DF14/14A- 8P-1.25H
8
24
11.5
24.4
–
–
–
DF14/14A- 9P-1.25H
9
24
11.5
24.4
–
–
–
DF14/14A-10P-1.25H
10
24
11.5
24.4
–
–
–
DF14/14A-15P-1.25H
15
44
20.2
44.4
40.4
DF14/14A-20P-1.25H
20
44
20.2
44.4
40.4
DF14/14A-25P-1.25H
25
56
26.2
56.4
52.4
DF14/14A-30P-1.25H
30
56
26.2
56.4
52.4
B181
BPrecautions
1. Recommended Temperature Profile (SMT)
Note 1.The soldering process is allowed up to twice under the same condition. However, the
interval between the first and second processes must be maintained at the room
temperature.
Note 1.The temperature indicates the board surface temperature on the connector lead area.
2. Recommended Manual Soldering Condition (SMT)
Manual soldering: 290ç for 2 seconds
3. Recommended Screen Thickness (SMT)
0.15 to 0.2mm
4. Board Sled (SMT)
Max 0.03mm at the connector center area, based on both connector edges
5. Cleaning Condition
Refer to Nylon Connector Use Hand book.
6. Connection Condition
Refer to Nylon Connector Use Hand book.
■Be careful to carry out the crimping operation according to the "Crimping Condition Sheet"
and "Crimping Quality Reference", because the crimping contact style is too small.
7. Cautions
■Be careful for an excessive scoop insertion/extraction, which will cause damage to the
product.
B182
Similar pages