DG08 miniature automotive twin power relay • miniature - only 24.3 x 15.8 x 14mm. • 2 relays in one package • simplified coil connections • Up to 60A 12VDC switching. • Special option for motor loads. • RoHS Compliant. Contacts Contact number & arrangement 2 x SPDT (1 Form C) Contact material AgNi0.15; AgNi90/10; AgSnOInO Max. switching voltage DC 16VDC (consult factory for 24VDC) Min. switching current / voltage 100mA / 5VDC (AgNi0.15); 500mA / 5VDC (AgSnOInO) Rated load DC1 20A/12VDC Max. continuous current DC1 35A (10 mins) / 25A (1hr) Max. switching current (AgSnOInO) 2 Make 60A Break 20A Initial contact resistance 100mΩ max. at 0.1A/6VDC Coil Rated voltage DC 6...24V Must release voltage ≥0.1Un Operating range of supply voltage See coil table 1 and coil table 2 Rated power consumption DC 0.6W (table 1) / 0.8W (table 2) for increased contact gap version Insulation Insulation resistance 100MΩ at 500VDC, 50%RH Dielectric strength coil to contact 500Vrms, 1min contact to contact 500Vrms, 1min General Data Operating time (typical) ms 10 Release time (typical) ms 5 Electrical Life ops 1 x 105 3 Mechanical life Dimensions Weight ops 1 x 107 L x W x H 24.3 x 15.8 x 14.0mm (excluding terminal pins) 13g approx. Ambient temperature storage -40 to 100°C operating -30 to 85°C Shock resistance Functional: 10g 11ms; Destructive: 100g Vibration resistance DA 1.5mm 10-55Hz Page 1 of 3 Ref: DG08 121913JHM www.aecsensors.com Sales Department Tel: (888) 847-6552 DG08 miniature automotive twin power relay Coil Data (600mW - standard version) Coil Voltage Code Table 1 Nominal Voltage (VDC) Coil Resistance (Ω) ±10% Must operate voltage max. (VDC) Must release voltage min. (VDC) S006 6 60 3.6 0.6 S009 9 135 5.4 0.9 S010 10 167 6.3 1.0 S012 12 240 7.3 1.2 S024 24 960 14.4 2.4 Coil Data (800mW - increased contact gap version)* Coil Voltage Code Nominal Voltage (VDC) Table 2 Coil Resistance (Ω) ±10% Must operate voltage max. (VDC) Must release voltage min. (VDC) 1006 6 45 3.6 0.6 1009 9 100 5.4 0.9 1010 10 123 6.3 1.0 1012 12 180 7.3 1.2 1024 24 720 14.4 2.4 * Contact gap increased to 0.45mm Ordering codes Contact material Type D G 0 8 - Contact arrangement Cover protection and mounting - 5 Coil code - - Contact material 20 - AgNi (90/10) 70 - AgSnOInO 80 - AgNi 0.15 See coil tables 1 or 2 Contact arrangement 11 - SPDT (1 C/O, 1 Form C) Cover protection category 2 - in cover, flux tight - IP40 3 - in cover, sealed - IP67 Connection mode 5 - for PCB Options Nil - No options G - Increased contact gap (may be specified with std, Class F or Class H insulation) F - UL Class F insulation for higher ambient temperatures H - UL Class H insulation for high ambient temperatures M - Suitable for reflow soldering Page 2 of 3 Ref: DG08 121913JHM www.aecsensors.com Sales Department Tel: (888) 847-6552 DG08 miniature automotive twin power relay Overall Dimensions Fig. 1 PCB Mounting Dimensions Fig. 2 min Mounting Holes (Bottom View) Wiring Diagrams (Bottom View) Dimensions in mm Reference Curves Fig. 3 Life Expectancy Operations (1x104) Switching Current (A) Power Load Limit Contact Voltage (VDC) Locked Motor Current (A) Notes: 1: All parameters, unless otherwise specified, are measured at ambient temperature of 23ºC. 2: Maximum make current refers to inrush current of lamp load. 3: Electrical life of obtained at motor load of locked rotor at 25A, 13.5VDC, with operating frequency of 6 ops/sec. 4: Electrical life is strongly dependent of switching frequency, On/Off ratio and environmental conditions. Specifications are subject to change without notice. E&OE. Page 3 of 3 Ref: DG08 121913JHM American Electronic Components Inc., 1101 Lafayette St. Elkhart, IN46516 www.aecsensors.com Sales Department Tel: (888) 847-6552