Willow CCP-18D23C-T Commercial normally open multi-throw, dc-3ghz, low pim Datasheet

Series CCP-18D
COAX SWITCHES
Low PIM Multi-Throw DC–3 GHz
Normally Open Coaxial Switch
PART NUMBER
DESCRIPTION
CCP-18D
Commercial Normally Open Multi-throw, DC-3GHz, Low PIM
These switches have extremely low passive intermodulation for use in narrow bandwidth communications
applications.
The CCP-18D is a broadband multi-position coaxial switch designed to switch RF signals from one input
port to any one of 3 or 4 output ports. It is designed for 50 Ohms transmission line systems. The standard
actuator gives individual solenoid control of each position and when de-energized, all positions are open.
ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS
ELECTRICAL CHARACTERISTICS
Operating Temperature
–40°C to 65°C
Form Factor
Vibration (MIL-STD-202 Method 214,
Condition D, non-operating)
10 g’s RMS
Shock (MIL-STD-202 Method 213,
Condition D, non-operating)
500 g’s
Standard Actuator Life
1,000,000 cycles
Connector Type
7/16 DIN
Humidity (Moisture Seal)
Available
Weight
9 oz. (255.2g) (max.)
Multi-Throw,
break before make
Frequency Range
DC–3 GHz
Characteristic Impedance
50 Ohms
Switching Time
20 ms (max.)
Actuation Voltage Available
12
15
24
28 V
Actuation Current, max. @ ambient
600 480 300 270 mA
PERFORMANCE CHARACTERISTICS
PASSIVE INTERMODULATION CHARACTERISTICS
Frequency
Tone 1 Frequency
(MHz)
Tone 2 Frequency
(MHz)
IM3 Frequency
(MHz)
PIM Threshold
(dBc)
1945
1990
1900
-140.0
P1 P2 (dBm)
PIM (dBc)
PEAK PIM (dBc)
43
-159.6
-156.6
DC–3 GHz
Insertion Loss, dB, max.
0.35
Isolation, dB, min.
70
VSWR , max.
1.3:1
RF Power (cw), W, max.
200
PART NUMBERING SYSTEM
CCP-18
D
1
3
C
-
T **
Series
Options
Connectors
Actuator Type
Actuator Voltage
Number of Positions
CONNECTOR
ACTUATOR VOLTAGE
NUMBER OF POSITIONS
ACTUATOR TYPE
OPTIONS
D: 7/16 FEMALE
1: 28 VDC NORMALLY OPEN
3: SP3T
0: NO INDICATOR CONTACTS
T: TTL DRIVERS WITH DIODES
2: 15 VDC NORMALLY OPEN
4: SP4T
C: INDICATOR CONTACTS
D: COIL TRANSIENT SUPPRESSION DIODES
3: 12 VDC NORMALLY OPEN
S: D-SUB CONNECTOR*
4: 24 VDC NORMALLY OPEN
TD: DECODERS AND TTL DRIVERS WITH
DIODES
M: MOISTURE SEAL
**SEE PARTS LIST ON PAGE 8
For additional options, please contact factory.
© 2013 TELEDYNE RELAYS
(800) 284-7007 • www.teledynecoax.com
* 15 pin D-Sub Connector
(See Connector Pinout page)
CCP-18 Page 1
CCP-18\072013\Q3
Series CCP-18D
COAX SWITCHES
Low PIM Multi-Throw DC–3 GHz
Normally Open Coaxial Switch
SCHEMATICS AND MECHANICAL OUTLINE
1
9
TELEDYNE COAX SWITCHES
P/N:
VOLTAGE:
D/C:
M/O:
VDC
RoHS
MADE IN
S C H E M A T IC
S H O W N IN
N O R M A LL Y O P E N P O S IT IO N
“-S OPTION” 15-PIN D-SUB CONNECTOR (EXAMPLE:
CCP-18D Page 2
CCP-18N160-S)
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2013 TELEDYNE COAX SWITCHES
CCP-18\072013\Q3
Series CCP-18D
COAX SWITCHES
Low PIM Multi-Throw DC–3 GHz
Normally Open Coaxial Switch
CONNECTOR PINOUT FOR NORMALLY OPEN SP3T MULTI-THROW SWITCHES
EXAMPLE
CCP-18D130-S
INDICATOR
CCP-18D13C-S
CCP-18D130-TS
YES
TTL
CCP-18D13C-TS
CCP-18D130-TDS
YES
YES
YES
CCP-18D13C-TDS
YES
DECODERS & TTL
YES
YES
9-PIN
9-PIN
9-PIN
9-PIN
9-PIN
9-PIN
1
PORT 1
PORT 1
PORT 1
PORT 1
LOGIC 1
LOGIC 1
2
PORT 2
PORT 2
PORT 2
PORT 2
LOGIC 2
LOGIC 2
3
PORT 3
PORT 3
PORT 3
PORT 3
PIN NO.
4
E INDICATOR
E INDICATOR
5
F INDICATOR
F INDICATOR
F INDICATOR
6
G INDICATOR
G INDICATOR
G INDICATOR
7
COMMON
COMMON
8
COMMON
VSW
9
D INDICATOR (COM)
E INDICATOR
COMMON
COMMON
VSW
VSW
D INDICATOR (COM)
COMMON
VSW
D INDICATOR (COM)
CONNECTOR PINOUT FOR NORMALLY OPEN SP4T MULTI-THROW SWITCHES
EXAMPLE
CCP-18D140-S
CCP-18D14C-S
CCP-18D140-TS
YES
INDICATOR
TTL
CCP-18D14C-TS
CCP-18D140-TDS
YES
YES
YES
CCP-18D14C-TDS
YES
DECODERS & TTL
YES
YES
9-PIN
15-PIN
9-PIN
15-PIN
9-PIN
15-PIN
1
PORT 1
PORT 1
TTL 1
TTL 1
LOGIC 1
LOGIC 1
2
PORT 2
PORT 2
TTL 2
TTL 2
LOGIC 2
LOGIC 2
3
PORT 3
PORT 3
TTL 3
TTL 3
LOGIC 3
LOGIC 3
4
PORT 4
PORT 4
TTL 4
TTL 4
COMMON
COMMON
COMMON
COMMON
COMMON
COMMON
VSW
VSW
VSW
PIN NO.
5
6
7
8
VSW
9
D INDICATOR (COM)
D INDICATOR (COM)
D INDICATOR (COM)
10
E INDICATOR
E INDICATOR
E INDICATOR
11
F INDICATOR
F INDICATOR
F INDICATOR
12
G INDICATOR
G INDICATOR
G INDICATOR
N/A
13
N/A
N/A
H INDICATOR
H INDICATOR
H INDICATOR
14
15
1
9
15-PIN D-SUB CONNECTOR
© 2013 TELEDYNE RELAYS
(800) 284-7007 • www.teledynecoax.com
CCP-18 Page 3
CCP-18\072013\Q3
Series CCP-18D
COAX SWITCHES
Low PIM Multi-Throw DC–3 GHz
Normally Open Coaxial Switch
TRUTH TABLE Normally Open
CCP-18DX3C-T
Logic
Input
RF Path
1
2
3
J1
J2
1
0
0
1
0
On
0
Off
0
0
1
Off
Indicator
Switches
J3
E
F
G
Off
Off
On
Off
C
0
0
0
C
0
Off
On
0
0
C
TRUTH TABLE Normally Open
CCP-18DX3C-TD
Logic
Input
1
RF Path
2
J1
J2
Indicator
Switches
J3
E
F
G
0
0
On
Off
Off
C
0
0
1
0
Off
On
Off
0
C
0
0
1
Off
Off
On
0
0
C
1
1
Off
Off
Off
0
0
0
TRUTH TABLE Normally Open
CCP-18DX4C-T
Logic Input
RF Path
Indicator
Switches
1
2
3
4
J1
J2
J3
J4
E
F
G
H
1
0
0
0
On
Off
Off
Off
C
0
0
0
0
1
0
0
Off
On
Off
Off
0
C
0
0
0
0
1
0
Off
Off
On
Off
0
0
C
0
0
0
0
1
Off
Off
Off
On
0
0
0
C
TRUTH TABLE Normally Open
CCP-18DX4C-TD
Logic Input
RF Path
Indicator
Switches
1
2
3
J1
J2
J3
J4
E
F
G
H
0
0
0
On
Off
Off
Off
C
0
0
0
1
0
0
Off
On
Off
Off
0
C
0
0
0
1
0
Off
Off
On
Off
0
0
C
0
1
1
0
Off
Off
Off
On
0
0
0
C
1
1
1
Off
Off
Off
Off
0
0
0
0
CCP-18D Page 4
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2013 TELEDYNE COAX SWITCHES
CCP-18\072013\Q3
Series CCP-18D
COAX SWITCHES
Low PIM Multi-Throw DC–3 GHz
Normally Open Coaxial Switch
TYPICAL BROADBAND RF PERFORMANCE CURVES
Insertion Loss ( DC-3 GHz )
0.0
-0.1
Insertion Loss ( dB )
-0.2
-0.3
-0.4
-0.5
-0.6
-0.7
-0.8
-0.9
-1.0
0
0.5
1
1.5
2
2.5
3
2
2.5
3
2
2.5
3
Frequency ( GHz )
Isolation ( DC-3 GHz )
0
Isolation ( dB )
-20
-40
-60
-80
-100
-120
-140
0
0.5
1
1.5
Frequency ( GHz )
VSWR ( DC-3 GHz )
2.0
1.9
1.8
VSWR
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
0
0.5
1
1.5
Frequency ( GHz )
RF NOTES
© 2013 TELEDYNE RELAYS
(800) 284-7007 • www.teledynecoax.com
CCP-18 Page 5
CCP-18\072013\Q3
Series CCP-18D
COAX SWITCHES
Low PIM Multi-Throw DC–3 GHz
Normally Open Coaxial Switch
TYPICAL POWER PERFORMANCE CURVE
Power Handling vs. Frequency
3000
2000
7/1
6D
IN C
onn
1000
800
600
ect
or S
wit
ch
Power (W)
400
300
200
100
80
60
40
30
20
10
.1
.2
.3 .4 .6 .8 1
2
3
Frequency GHz
Estimates based on the following reference conditions:
• Ambient temperature of 40°C or less
• Sea level operation
• Load VSWR of 1.20:1 maximum
• No high-power (hot) switching
Please contact Teledyne Coax Switches for derating factors when applications do not meet the foregoing reference conditions.
CCP-18D Page 6
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2013 TELEDYNE COAX SWITCHES
CCP-18\072013\Q3
Series CCP-18D
COAX SWITCHES
Low PIM Multi-Throw DC–3 GHz
Normally Open Coaxial Switch
GLOSSARY
Actuator
An actuator is the electromechanical mechanism that
transfers the RF contacts from one position to another upon
DC command.
Arc Suppression Diode
A diode is connected in parallel with the coil. This diode
limits the “reverse EMF spike” generated when the coil deenergizes to 0.7 volts. The diode cathode is connected to
the positive side of the coil and the anode is connected to
the negative side.
Date Code
All switches are marked with either a unique serial number
or a date code. Date codes are in accordance with MILSTD-1285 Paragraph 5.2.5 and consist of four digits.
The first two digits define the year and the last two digits
define the week of the year (YYWW). Thus, 1032 identifies
switches that passed through final inspection during the
32nd week of 2010.
Indicator
Indicators tell the system which position the switch is in.
Other names for indicators are telemetry contacts or tellback
circuit. Indicators are usually a set of internally mounted DC
contacts linked to the actuator. They can be wired to digital
input lines, status lights, or interlocks. Unless otherwise
specified, the maximum indicator contact rating is 30 Vdc,
50 mA, or 1.5 Watts into a resistive load.
Isolation
Isolation is the measure of the power level at the output
connector of an unconnected RF channel as referenced to
the power at the input connector. It is specified in dB below
the input power level.
Multi-Throw Switch
A multi-throw switch is a switch with one input and three
or more output ports. The CCP-18 can switch a microwave
signal to any of 2,3,4,5 or 6 output from a single common
input.
TD-Option
This option includes a decoder. The 3-bit parallel command
is decoded to internally select the appropriate position. See
the logic tables. The TD-Option increases the Vsw supply
current demand by 50mA max at 28Vdc and +20°C.
Performance Parameters vs Frequency
Generally speaking, the RF performance of coaxial switches
is frequency dependent. With increasing frequency, VSWR
and insertion loss increase while isolation decreases. All
data sheets specify these three parameters as “worst case”
at the highest operating frequency. If the switch is to be
used over a narrow frequency band, better performance
can be achieved.
Actuator Current vs Temperature
The resistance of the actuator coil varies as a function of
temperature. There is an inverse relationship between the
operating temperature of the switch and the actuator drive
current. For switches operating at 28 VDC, the approximate
actuator drive current at temperature, T, can be calculated
using the equation:
IT =
IA
[1 + .00385 (T-20)]
Where:
IT = Actuator current at temperature, T
IA = Room temperature actuator current –
see data sheet
T = Temperature of interest in °C
Magnetic Sensitivity
An electro-mechanical switch can be sensitive to ferrous
materials and external magnetic fields. Neighboring ferrous
materials should be permitted no closer than 0.5 inches and
adjacent external magnetic fields should be limited to a flux
density of less than 5 Gauss.
Switching Time
Switching time is the total interval beginning with the arrival
of the leading edge of the command pulse at the switch DC
input and ending with the completion of the switch transfer,
including contact bounce. It consists of three parts: (1)
inductive delay in the coil, (2) transfer time of the physical
movement of the contacts, and (3) the bounce time of the
RF contacts.
TTL Switch Driver Option
As a special option, switch drivers can be provided for both
failsafe and latching switches, which are compatible with
industry-standard low-power Schottky TTL circuits.
© 2013 TELEDYNE RELAYS
(800) 284-7007 • www.teledynecoax.com
CCP-18 Page 7
CCP-18\072013\Q3
Series CCP-18D
COAX SWITCHES
Low PIM Multi-Throw DC–3 GHz
Normally Open Coaxial Switch
NORMALLY OPEN CCP-18D PART NUMBER LIST
PART NO.
*
PART NO.
1
CCP-18DX3C
43
CCP-18DX40
2
CCP-18DX3C-D
44
CCP-18DX40-D
3
CCP-18DX3C-DM
45
CCP-18DX40-DM
4
CCP-18DX3C-M
46
CCP-18DX40-M
5
CCP-18DX3C-MS
47
CCP-18DX40-MS
6
CCP-18DX3C-S
48
CCP-18DX40-S
7
CCP-18DX3C-T
49
CCP-18DX40-T
8
CCP-18DX3C-TD
50
CCP-18DX40-TD
9
CCP-18DX3C-TDM
51
CCP-18DX40-TDM
10
CCP-18DX3C-TDMS
52
CCP-18DX40-TDMS
11
CCP-18DX3C-TDS
53
CCP-18DX40-TDS
12
CCP-18DX3C-TM
54
CCP-18DX40-TM
13
CCP-18DX3C-TMS
55
CCP-18DX40-TMS
14
CCP-18DX3C-TS
56
CCP-18DX40-TS
15
CCP-18DX30
16
CCP-18DX30-D
17
CCP-18DX30-DM
18
CCP-18DX30-M
19
CCP-18DX30-MS
20
CCP-18DX30-S
21
CCP-18DX30-T
22
CCP-18DX30-TD
23
CCP-18DX30-TDM
24
CCP-18DX30-TDMS
25
CCP-18DX30-TDS
26
CCP-18DX30-TM
27
CCP-18DX30-TMS
28
CCP-18DX30-TS
29
CCP-18DX4C
30
CCP-18DX4C-D
31
CCP-18DX4C-DM
32
CCP-18DX4C-M
33
CCP-18DX4C-MS
34
CCP-18DX4C-S
35
CCP-18DX4C-T
36
CCP-18DX4C-TD
37
CCP-18DX4C-TDM
38
CCP-18DX4C-TDMS
39
CCP-18DX4C-TDS
40
CCP-18DX4C-TM
41
CCP-18DX4C-TMS
42
CCP-18DX4C-TS
X = 1 (28Vdc), 2 (15Vdc), 3 (12Vdc) and 4 (24Vdc)
CCP-18D Page 8
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE
© 2013 TELEDYNE COAX SWITCHES
CCP-18\072013\Q3
Similar pages