AVAGO AFBR-57M5APZ Digital diagnostic optical transceiver Datasheet

AFBR-57M5APZ
850 nm, 2.125/1.0625 and 1.25 GBd Ethernet,
Low Voltage (3.3 V), RoHS Compliant, SFP (Small Form Pluggable),
Digital Diagnostic Optical Transceiver,
5APZ
-57MSER PROD
S1
LA
AFBR
0nm CLAS
Data Sheet
2-DI
10
OC-4
85
0446
F(J)
21CR APORE CD1C
SING: AJ0446
SN
n2
PP
Description
Features
Avago’s AFBR-57M5APZ optical transceiver supports
high-speed serial links over multimode optical fiber at
signaling rates up to 2.125 Gb/s. Compliant with Small
Form Pluggable (SFP) Multi Source Agreement (MSA)
mechanical and electrical specifications for LC Duplex
transceivers, ANSI Fibre Channel FC-PI, FC-PI-2 and
compliant with IEEE 802.3 for gigabit applications. The
part is electrically interoperable with SFP conformant
devices.
• Fully RoHS Compliant
• Diagnostic features per SFF-8472 “Diagnostic
Monitoring Interface for Optical Transceivers”
• Real time monitoring of:
– Transmitted optical power
– Received optical power
– Laser bias current
– Temperature
– Supply voltage
• Wide temperature and supply voltage operation
(-10°C to 85°C) (3.3 V ± 10%)
• Transceiver specifications per SFP (SFF-8074i) MultiSource Agree-ment and SFF-8472 (revision 9.3)
– 2.125 GBd Fibre Channel operation
for FC-PI 200-M5-SN-I and 200-M6-SN-I
– 1.0625 GBd Fibre Channel operation
for FC-PI 100-M5-SN-I and 100-M6-SN-I
– 1.25 GBd operation for IEEE 802.3 Gigabit Ethernet
1000Base-SX
• Link lengths at 2.125 GBd:
– 300 m with 50 µm MMF, 150 m with 62.5 µm MMF
• Link lengths at 1.0625 GBd:
– 500 m with 50 µm MMF, 300 m with 62.5 µm MMF
• Link lengths at 1.25 GBd:
– 2 to 550 m with 50 µm MMF, 2 to 275 m with
62.5 µm MMF
• LC Duplex optical connector interface conforming to
ANSI TIA/EIA604-10 (FOCIS 10A)
• 850 nm Vertical Cavity Surface Emitting Laser (VCSEL)
source technology
• IEC 60825-1 Class 1/CDRH Class 1 laser eye safe
Applications
• Fibre channel systems
– Director class switches
– Fabric switches
– HBA cards
• Disk and tape drive arrays
Related Products
• AFBR-59R5LZ: 850 nm +3.3 V LC SFF 2x7 for
4.25/2.125/1.0625 GBd Fibre Channel
• AFBR-57R5APZ: 850 nm +3.3 V LC SFP for
4.25/2.125/1.0625 GBd Fibre Channel
Patent - www.avagotech.com/patents
Description, continued
As an enhancement to the conventional SFP interface
defined in SFF-8074i, the AFBR-57M5APZ is compliant
to SFF-8472 (digital diagnostic interface for optical
transceivers). Using the 2-wire serial interface defined
in the SFF-8472 MSA, the AFBR-57M5APZ provides real
time temperature, supply voltage, laser bias current,
laser average output power and received input power.
This information is in addition to conventional SFP
base data. The digital diagnostic interface also adds the
ability to disable the transmitter (TX_DISABLE), monitor
for Transmitter Faults (TX_FAULT), and monitor for
Receiver Loss of Signal (RX_LOS).
Compliance Prediction
Installation
Fault Isolation
The AFBR-57M5APZ can be installed in any SFF-8074i
compliant Small Form Pluggable (SFP) port regardless
of host equipment operating status. The AFBR-57M5APZ
is hot-pluggable, allowing the module to be installed
while the host system is operating and on-line. Upon
insertion, the transceiver housing makes initial contact
with the host board SFP cage, mitigating potential
damage due to Electro-Static Discharge (ESD).
The fault isolation feature allows a host to quickly
pinpoint the location of a link failure, minimizing
downtime. For optical links, the ability to identify a fault
at a local device, remote device or cable plant is crucial
to speeding service of an installation. AFBR-57M5APZ
real-time monitors of Tx_Bias, Tx_Power, Vcc, Temperature and Rx_Power can be used to assess local transceiver current operating conditions. In addition, status flags
Tx_Disable and Rx Loss of Signal (LOS) are mirrored in
memory and available via the two-wire serial interface.
Digital Diagnostic Interface and Serial Identification
The 2-wire serial interface is based on ATMEL AT24C01A
series EEPROM protocol and signaling detail. Conventional EEPROM memory, bytes 0-255 at memory
address 0xA0, is organized in compliance with SFF8074i. New digital diag­nostic information, bytes 0-255
at memory address 0xA2, is compliant to SFF-8472. The
new diagnostic information provides the opportunity
for Predictive Failure Identification, Com­pliance Prediction, Fault Isolation and Component Monitoring.
The I2C accessible memory page address 0xB0 is used
internally by SFP for the test and diagnostic purposes
and it is reserved.
Predictive Failure Identification
The AFBR-57M5APZ predictive failure feature allows a
host to identify potential link problems before system
performance is impacted. Prior identification of link
problems enables a host to service an application via
“fail over” to a redundant link or replace a suspect
device, maintaining system uptime in the process. For
applications where ultra-high system uptime is required,
a digital SFP provides a means to monitor two real-time
laser metrics asso­ciated with observing laser degradation and predicting failure: average laser bias current
(Tx_Bias) and average laser optical power (Tx_Power).
2
Compliance prediction is the ability to determine if an
optical transceiver is operating within its operating and
environmental requirements. AFBR-57M5APZ devices
provide real-time access to transceiver internal supply
voltage and temperature, allowing a host to identify
potential component compliance issues. Received
optical power is also available to assess compliance of
a cable plant and remote transmitter. When operating
out of requirements, the link cannot guarantee error
free transmission.
Component Monitoring
Component evaluation is a more casual use of the
AFBR-57M5APZ real-time monitors of Tx_Bias, Tx_Power,
Vcc, Temperature and Rx_Power. Potential uses are as
debugging aids for system installation and design, and
transceiver parametric evaluation for factory or field
qualification. For example, temperature per module can
be observed in high density applications to facilitate
thermal evaluation of blades, PCI cards and systems.
OPTICAL INTERFACE
LIGHT FROM FIBER
ELECTRICAL INTERFACE
RECEIVER
AMPLIFICATION
& QUANTIZATION
PHOTO-DETECTOR
RD+ (RECEIVE DATA)
RD– (RECEIVE DATA)
Rx LOSS OF SIGNAL
MOD-DEF2 (SDA)
CONTROLLER & MEMORY
MOD-DEF1 (SCL)
MOD-DEF0
TRANSMITTER
LIGHT TO FIBER
VCSEL
TX_DISABLE
LASER
DRIVER &
SAFETY
CIRCUITRY
TD+ (TRANSMIT DATA)
TD– (TRANSMIT DATA)
TX_FAULT
Figure 1. Transceiver functional diagram.
Transmitter Section
Transmit Fault (Tx_Fault)
The transmitter section includes consists of the Transmitter Optical SubAssembly (TOSA) and laser driver
circuitry. The TOSA, containing an 850 nm VCSEL
(Vertical Cavity Surface Emitting Laser) light source, is
located at the optical interface and mates with the LC
optical connector. The TOSA is driven by a custom IC
which uses the incoming differential high speed logic
signal to modulate the laser diode driver current. This
Tx laser driver circuit regulates the optical power at a
constant level provided the incoming data pattern is dc
balanced (8B/10B code, for example).
A catastrophic laser fault will activate the transmitter
signal, TX_FAULT, and disable the laser. This signal is
an open collector output (pull-up required on the host
board). A low signal indicates normal laser operation
and a high signal indicates a fault. The TX_FAULT will
be latched high when a laser fault occurs and is cleared
by toggling the TX_DISABLE input or power cycling the
transceiver. The transmitter fault condition can also be
monitored via the two-wire serial interface (address A2,
byte 110, bit 2).
Transmit Disable (Tx_Disable)
The AFBR-57M5APZ accepts a TTL and CMOS compatible transmit disable control signal input (pin 3) which
shuts down the transmitter optical output. A high signal
implements this function while a low signal allows
normal transceiver operation. In the event of a fault (e.g.
eye safety circuit activated), cycling this control signal
resets the module as depicted in Figure 4. An internal
pull up resistor disables the transceiver transmitter until
the host pulls the input low. Host systems should allow
a 10 ms interval between successive assertions of this
control signal. Tx_Disable can also be asserted via the
two-wire serial interface (address A2h, byte 110, bit 6)
and monitored (address A2h, byte 110, bit 7).
The contents of A2h, byte 110, bit 6 are logic OR’d with
hardware Tx_Disable (pin 3) to control transmitter
operation.
3
Eye Safety Circuit
The AFBR-57M5APZ provides Class 1 (single fault
tolerant) eye safety by design and has been tested for
compliance with the requirements listed in Table 1. The
eye safety circuit continuously monitors the optical
output power level and will disable the transmitter
upon detecting an unsafe condition beyond the scope
of Class 1 certification. Such unsafe conditions can be
due to inputs from the host board (Vcc fluctuation, unbalanced code) or a fault within the transceiver.
Receiver Section
The receiver section includes the Receiver Optical
SubAssembly (ROSA) and the amplification/quantization circuitry. The ROSA, containing a PIN photodiode and custom transimpedance amplifier, is located
at the optical interface and mates with the LC optical
connector. The ROSA output is fed to a custom IC that
provides post-amplification and quantization.
Receiver Loss of Signal (Rx_LOS)
Caution
The post-amplification IC also includes transition
detection circuitry which monitors the ac level of
incoming optical signals and provides a TTL/CMOS compatible status signal to the host (pin 8). An adequate
optical input results in a low Rx_LOS output while a high
Rx_LOS output indicates an unusable optical input. The
Rx_LOS thresholds are factory set so that a high output
indicates a definite optical fault has occurred. Rx_LOS
can also be monitored via the two-wire serial interface
(address A2h, byte 110, bit 1).
There are no user serviceable parts nor maintenance
requirements for the AFBR-57M5APZ. All mechanical
adjustments are made at the factory prior to shipment.
Tampering with, modifying, misusing or improperly
handling the AFBR-57M5APZ will void the product
warranty. It may also result in improper operation
and possibly overstress the laser source. Performance
degrada­tion or device failure may result. Connection of
the AFBR-57M5APZ to a light source not compliant with
ANSI FC-PI or IEEE 802.3 specifications, operating above
maximum operating conditions or in a manner inconsistent with it’s design and function may result in exposure
to hazardous light radiation and may constitute an act
of modifying or manufacturing a laser product. Persons
performing such an act are required by law to re-certify
and re-identify the laser product under the provisions of
U.S. 21 CFR (Subchapter J) and TUV.
Functional Data I/O
The AFBR-57M5APZ interfaces with the host circuit
board through twenty I/O pins (SFP electrical connector)
identified by function in Table 2. The board layout for
this interface is depicted in Figure 6.
The AFBR-57M5APZ high speed transmit and receive
interfaces require SFP MSA compliant signal lines on
the host board. To simplify board requirements, biasing
resistors and ac coupling capacitors are incorporated
into the SFP transceiver module (per SFF-8074i) and
hence are not required on the host board. The Tx_
Disable, Tx_Fault, and Rx_LOS lines require TTL lines on
the host board (per SFF-8074i) if used. If an application
chooses not to take advantage of the functionality of
these pins, care must be taken to ground Tx_Disable (for
normal operation).
Figure 2 depicts the recom­mended interface circuit to
link the AFBR-57M5APZ to supporting physical layer ICs.
Timing for MSA compliant control signals implemented
in the transceiver are listed in Figure 4.
Application Support
An Evaluation Kit and Reference Designs are available
to assist in evaluation of the AFBR-57M5APZ. Please
contact your local Field Sales representative for availability and ordering details.
4
Ordering Information
Please contact your local field sales engineer or one of
Avago Technologies franchised distributors for ordering
information. For technical information, please visit
Avago Technologies’ WEB page at www.Avago.com or
contact Avago Technologies Semicon-ductor Products
Customer Response Center at 1-800-235-0312. For information related to SFF Committee documentation
visit www.sffcommittee.org.
Regulatory Compliance
The AFBR-57M5APZ complies with all applicable laws
and regulations as detailed in Table 1. Certification level
is dependent on the overall configuration of the host
equipment. The transceiver performance is offered as a
figure of merit to assist the designer.
Electrostatic Discharge (ESD)
The AFBR-57M5APZ is compatible with ESD levels found
in typical manufacturing and operating environments
as described in Table 1. In the normal handling and
operation of optical transceivers, ESD is of concern in
two circumstances.
The first case is during handling of the transceiver prior
to insertion into an SFP compliant cage. To protect the
device, it’s important to use normal ESD handling precautions. These include use of grounded wrist straps,
work-benches and floor wherever a transceiver is
handled.
The second case to consider is static discharges to the
exterior of the host equipment chassis after installation.
If the optical interface is exposed to the exterior of host
equipment cabinet, the transceiver may be subject to
system level ESD requirements.
Electromagnetic Interference (EMI)
Equipment incorporating gigabit transceivers is
typically subject to regulation by the FCC in the United
States, CENELEC EN55022 (CISPR 22) in Europe and VCCI
in Japan. The AFBR-57M5APZ’s compliance to these
standards is detailed in Table 1. The metal housing and
shielded design of the AFBR-57M5APZ minimizes the
EMI challenge facing the equipment designer.
EMI Immunity (Susceptibility)
Due to its shielded design, the EMI immunity of the
AFBR-57M5APZ exceeds typical industry standards.
Flammability
The AFBR-57M5APZ optical transceiver is made of metal
and high strength, heat resistant, chemical resistant and
UL 94V-0 flame retardant plastic.
Table 1. Regulatory Compliance
Feature
Test Method
Performance
Electrostatic Discharge (ESD)
to the Electrical Pins
MIL-STD-883C
Method 3015.4
Class 1 (> 2000 Volts)
Electrostatic Discharge (ESD)
Variation of IEC 61000-4-2
to the Duplex LC Receptacle
Typically, no damage occurs with 25 kV when
the duplex LC connector receptacle is
contacted by a Human Body Model probe.
GR1089
10 contacts of 8 kV on the electrical faceplate
with device inserted into a panel.
Electrostatic Discharge (ESD)
Variation of IEC 801-2
to the Optical Connector
Air discharge of 15 kV (min.) contact to
connector without damage.
Electromagnetic Interference
(EMI)
FCC Class B
CENELEC EN55022 Class B
(CISPR 22A)
VCCI Class 1
System margins are dependent on customer
board and chassis design.
Immunity
Variation of IEC 61000-4-3
Typically shows no measurable effect from a
10 V/m field swept from 10 MHz to 1 GHz.
Laser Eye Safety and
Equipment Type Testing
CDRH certification # 9720151-55
TUV file # TBD
US FDA CDRH AEL Class 1
US21 CFR, Subchapter J per
Paragraphs 1002.10
and 1002.12
BAUART
¨
GEPRUFT
(IEC) EN60825-1: 1994 + A11 + A2
(IEC) EN60825-2: 1994 + A1
(IEC) EN60950: 1992 + A1 + A2 +
A3 + A4 + A11
¨
TUV
Rheinland
Product Safety
TYPE
APPROVED
Component Recognition
Underwriters Laboratories and
Canadian Standards Association
Joint Component Recognition
for Information Technology
Equipment including Electrical
Business Equipment
RoHS Compliance
5
UL File #E173874
Less than 1000 ppm of cadmium, lead, mercury,
hexavalent chromium, polybrominated biphe
nyls, and polybrominated biphenyl ethers.
VCC,T
GND,T
6.8 kΩ
Tx DIS
Tx_DISABLE
Tx FAULT
Tx_FAULT
TD+
0.01 µF
100 Ω
TD–
0.01 µF
LASER DRIVER
4.7 k to 10 kΩ
1 µH
VCC,T
0.1 µF
3.3 V
SERDES IC
PROTOCOL IC
10 µF
0.1 µF
1 µH
10 µF
VCC,R
VCC,R
VCC,R
0.1 µF
50 Ω
4.7 k to
10 kΩ
RD+
50 Ω
0.01 µF
100 Ω
RD–
0.01 µF
Rx LOS
LOSS OF SIGNAL
POST AMPLIFIER
3.3 V
GND,R
4.7 k to 10 kΩ
4.7 k to 10 kΩ
MOD_DEF0
4.7 k to 10 kΩ
MODULE DETECT
SCL
SDA
Figure 2. Typical application configuration.
1 µH
VCCT
0.1 µF
1 µH
VCCR
0.1 µF
SFP MODULE
10 µF
3.3 V
0.1 µF
10 µF
HOST BOARD
NOTE: INDUCTORS MUST HAVE LESS THAN 1 Ω SERIES RESISTANCE TO LIMIT VOLTAGE DROP TO THE SFP MODULE.
Figure 3. Recommended power supply filter.
6
MOD_DEF1
MOD_DEF2
Table 2. Pin Description
Pin
Name
Function/Description
Notes
1
VeeT
Transmitter Ground
2
TX_FAULT
Transmitter Fault Indication – High indicates a fault condition
Note 1
3
TX_DISABLE
Transmitter Disable – Module electrical input disables on high or open
Note 2
4
MOD-DEF2
Module Definition 2 – Two wire serial ID interface data line (SDA)
Note 3
5
MOD-DEF1
Module Definition 1 – Two wire serial ID interface clock line (SCL)
Note 3
6
MOD-DEF0
Module Definition 0 – Grounded in module (module present indicator)
Note 3
7
N.C.
8
RX_LOS
Loss of Signal – High indicates loss of received optical signal
Note 4
9
VeeR
Receiver Ground
10
VeeR
Receiver Ground
11
VeeR
Receiver Ground
12
RD-
Inverse Received Data Out
Note 5
13
RD+
Received Data Out
Note 5
14
VeeR
Receiver Ground
15
VccR
Receiver Power + 3.3 V
Note 6
16
VccT
Transmitter Power + 3.3 V
Note 6
17
VeeT
Transmitter Ground
18
TD+
Transmitter Data In
Note 7
19
TD-
Inverse Transmitter Data In
Note 7
20
VeeT
Transmitter Ground
Notes:
1. TX_FAULT is an open collector/drain output, which must be pulled up with a 4.7 k – 10 kΩ resistor on the host board. When high, this output
indicates a laser fault of some kind. Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V.
2. TX_DISABLE is an input that is used to shut down the transmitter optical output. It is internally pulled up (within the transceiver) with a 6.8 kΩ
resistor.
Low (0 – 0.8 V): Transmitter on
Between (0.8 V and 2.0 V):
Undefined
High (2.0 – Vcc max) or OPEN:
Transmitter Disabled
3. The signals Mod-Def 0, 1, 2 designate the two wire serial interface pins. They must be pulled up with a 4.7 k – 10 kΩ resistor on the host board.
Mod-Def 0 is grounded by the module to indicate the module is present
Mod-Def 1 is serial clock line (SCL) of two wire serial interface
Mod-Def 2 is serial data line (SDA) of two wire serial interface
4. RX_LOS (Rx Loss of Signal) is an open collector/drain output that must be pulled up with a 4.7 k – 10 kΩ resistor on the host board. When high,
this output indicates the received optical power is below the worst case receiver sensitivity (as defined by the standard in use). Low indicates
normal operation. In the low state, the output will be pulled to < 0.8 V.
5. RD-/+ designate the differential receiver outputs. They are AC coupled 100 Ω differential lines which should be terminated with 100 Ω
differential at the host SERDES input. AC coupling is done inside the transceiver and is not required on the host board. The voltage swing on
these lines will be between 600 and 1600 mV differential (300 – 800 mV single ended) when properly terminated.
6. VccR and VccT are the receiver and transmitter power supplies. They are defined at the SFP connector pin. The maximum supply current is 300
mA and the associated in-rush current will typically be no more than 30 mA above steady state after 2 microseconds.
7. TD-/+ designate the differential transmitter inputs. They are AC coupled differential lines with 100 Ω differential termination inside the module.
The AC coupling is done inside the module and is not required on the host board. The inputs will accept differential swings of 400 – 2400 mV
(200 – 1200 mV single ended), though it is recommended that values between 500 and 1200 mV differential (250 – 600 mV single ended) be
used for best EMI performance.
7
Table 3. Absolute Maximum Ratings
Parameter
Symbol
Minimum
Maximum
Unit
Notes
Storage Temperature
TS
-40
100
C
Note 1, 2
Case Operating Temperature
TC
-40
100
C
Note 1, 2
Relative Humidity
RH
5
95
%
Note 1
Supply Voltage
VccT, R
-0.5
3.8
V
Note 1, 2, 3
Low Speed Input Voltage
VIN
-0.5
Vcc+0.5
V
Note 1
Notes;
1. Absolute Maximum Ratings are those values beyond which damage to the device may occur if these limits are exceeded for other than a short
period of time. See Reliability Data Sheet for specific reliability performance.
2. Between Absolute Maximum Ratings and the Recommended Operating Conditions functional performance is not intended, device reliability
is not implied, and damage to the device may occur over an extended period of time.
3. The module supply voltages, VCCT and VCCR must not differ by more than 0.5 V or damage to the device may occur.
Table 4. Recommended Operating Conditions
Parameter
Symbol
Minimum
Maximum
Unit
Notes
Case Operating Temperature
TC
-10
85
°C
Note 1, 2
Supply Voltage
VccT, R
2.97
3.63
V
Note 2
1.0625
2.125
Gb/s
Note 2
Data Rate Notes:
1. The Ambient Operating Temperature limitations are based on the Case Operating Temperature limitations and are subject to the host system
thermal design.
2. Recommended Operating Conditions are those values for which functional performance and device reliability is implied.
Table 5. Transceiver Electrical Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3 V ±10%)
Parameter
Symbol
Minimum
Typical
Maximum
PSNR
100
Unit
Notes
mV
Note 1
AC Electrical Characteristics
Power Supply Noise Rejection (peak-peak)
DC Electrical Characteristics
Module Supply Current
ICC210
mA
Power Dissipation
PDISS 765
mW
Low Speed Outputs:
Transmit Fault (TX_FAULT), Loss of Signal
(RX_LOS), MOD-DEF 2
VOH
2.0
V
VOL
0.8
V
VIH
2.0
Vcc
V
VIL
0
0.8
V
Low Speed Inputs:
Transmit Disable (TX_DIS),
MOD-DEF 1, MOD-DEF2
VccT,R+0.3
Notes:
1. Filter per SFP specification is required on host board to remove 10 Hz to 2 MHz content.
2. Pulled up externally with a 4.7 k – 10 kΩ resistor on the host board to 3.3 V.
3. Mod-Def1 and Mod-Def2 must be pulled up externally with a 4.7 k – 10 kΩ resistor on the host board to 3.3 V.
8
Note 2
Note 3
Table 6. Transmitter and Receiver Electrical Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3 V ±10%)
Parameter
Symbol
Minimum
High Speed Data Input:
Transmitter Differential Input Voltage (TD +/-)
VI
High Speed Data Output:
Receiver Differential Output Voltage (RD +/-)
Vo
Typical
Maximum
Unit
Notes
400
2400
mV
Note 1
600
1600
mV
Note 2
UI
Note 3
Receiver Contributed Total Jitter
TJ
0.26
(2.125 Gb/s)
124
Receiver Contributed Total Jitter
TJ
0.22
(1.0625 Gb/s)
205
Receiver Contributed Total Jitter
TJ
0.332
(1.25 Gb/s)
266
Receiver Electrical Output Rise & Fall Times
(20-80%)
tr, tf
50
150
ps
UI
Note 3
ps
UI
Note 3
ps
ps
Note 4
Notes:
1. Internally AC coupled and terminated (100 Ohm differential).
2. Internally AC coupled but requires an external load termination (100 Ohm differential).
3. Contributed DJ is measured on an oscilloscope in average mode with 50% threshold and K28.5 pattern. Contributed TJ is the sum of
contributed RJ and contributed DJ. Contributed RJ is calculated for 1x10-12 BER by multiplying the RMS jitter (measured on a single rise or
fall edge) from the oscilloscope by 14. Per FC-PI (Table 13 - MM jitter output, note 1), the actual contributed RJ is allowed to increase above
its limit if the actual contributed DJ decreases below its limits, as long as the component output DJ and TJ remain within their specified FC-PI
maximum limits with the worst case specified component jitter input.
4. 20%-80% electrical rise & fall times measured with a 500 MHz signal utilizing a 1010 data pattern.
9
Table 7. Transmitter Optical Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3V ±10%)
Parameter
Symbol
Minimum
Unit
Notes
Modulated Optical Output Power (OMA)
(Peak-to-Peak) 2.125 Gb/s
Tx,OMA
196
Typical
µW
Note 1
Modulated Optical Output Power (OMA)
(Peak-to-Peak) 1.0625 Gb/s
Tx,OMA
156
µW
Note 2
Average Optical Output Power
Pout
-9.0
dBm
Note 3, 4
Optical Extinction Ratio
ER
9
dB
Center Wavelength
lC
830
860
nm
Spectral Width – rms
s,rms
0.85
nm
Optical Rise/Fall Time (2.125 Gb/s)
tr, tf
150
ps
RIN 12 (OMA)
RIN
-118
dB/Hz
Transmitter Contributed Total Jitter (2.125 Gb/s)
TJ
0.25
UI
120
ps
Transmitter Contributed Total Jitter (1.0625 Gb/s)
0.27
UI
252
ps
Transmitter Contributed Total Jitter (1.25 Gb/s)
0.284
UI
TJ
TJ
Maximum
20% - 80%
Note 5
Note 5
Note 5
227
ps
Pout TX_DISABLE Asserted
dBm
POFF
-35
Notes:
1. An OMA of 196 µW is approximately equal to an average power of –9 dBm, avg assuming an Extinction Ratio of 9 dB.
2. An OMA of 156 µW is approximately equal to an average power of –10 dBm, avg assuming an Extinction Ratio of 9 dB.
3. Max Pout is the lesser of Class 1 safety limits (CDRH and EN 60825) or receiver power, max.
4. Into 50/125 µm (0.2 NA) multi-mode optical fiber.
5. Contributed DJ is measured on an oscilloscope in average mode with 50% threshold and K28.5 pattern. Contributed TJ is the sum of
contributed RJ and contributed DJ. Contributed RJ is calculated for 1x10-12 BER by multiplying the RMS jitter (measured on a single rise or
fall edge) from the oscilloscope by 14. Per FC-PI (Table 13 - MM jitter output, note 1), the actual contributed RJ is allowed to increase above
its limit if the actual contributed DJ decreases below its limits, as long as the component output DJ and TJ remain within their specified FC-PI
maximum limits with the worst case specified component jitter input.
10
Table 8. Receiver Optical Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3 V ±10%)
Parameter
Symbol
Input Optical Power [Overdrive]
PIN0
dBm, avg
Input Optical Modulation Amplitude
(Peak-to-Peak) 2.125 Gb/s [Sensitivity]
OMA
49
µW, OMA
Notes 1, 2
Input Optical Modulation Amplitude
(Peak-to-Peak) 1.0625 Gb/s [Sensitivity]
OMA
31
µW, OMA
Notes 1, 3
Receiver Sensitivity
(Optical Input Power)
PRMIN17
Stressed Receiver Sensitivity
(OMA) 2.125 Gb/s
Stressed Receiver Sensitivity
(OMA) 1.0625 Gb/s
Min.
Typ.
Max.
Unit
Notes
dBm
96
µW, OMA
50/125 µm fiber, Note 4
109
µW, OMA
62.5/125 µm fiber, Note 4
55
µW, OMA
50/125 µm fiber, Note 5
67
µW, OMA
62.5/125 µm fiber, Note 5
Stressed Receiver Sensitivity
(OMA) 1.25 Gb/s
-13.5
dBm
-12.5
dBm
Return Loss
12
dB
Bit Error Rate
BER
10^-12
Loss of Signal – Assert
PA27.5
-30
Loss of Signal - De-Assert
31
µW, OMA
-17.0
dBm, avg
Loss of Signal Hysteresis
0.5
dB
PD
PD - PA
-17.5
µW, OMA
dBm, avg
Note 6
Note 6
Notes:
1. Input Optical Modulation Amplitude (commonly known as sensitivity) requires a valid 8B/10B encoded input.
2. An OMA of 49 µW is approximately equal to an average power of –15 dBm, avg with an Extinction Ratio of 9 dB.
3. An OMA of 31 µW is approximately equal to an average power of –17 dBm, avg with an Extinction Ratio of 9 dB.
4. 2.125 Gb/s stressed receiver vertical eye closure penalty (ISI) min. is 1.26 dB for 50 µm fiber and 2.03 dB for 62.5 µm fiber. Stressed receiver DCD
component min. (at TX) is 40 ps.
5. 1.0625 Gb/s stressed receiver vertical eye closure penalty (ISI) min. is 0.96 dB for 50 µm fiber and 2.18 dB for 62.5 µm fiber. Stressed receiver
DCD component min. (at TX) is 80 ps.
6. These average power values are specified with an Extinction Ratio of 9 dB. The loss of signal circuitry responds to valid 8B/10B encoded peak
to peak input optical power, not average power.
11
Table 9. Transceiver SOFT DIAGNOSTIC Timing Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3 V ±10%)
Parameter
Symbol
Hardware TX_DISABLE Assert Time
Minimum
Maximum
Unit
Notes
t_off
10
µs
Note 1
Hardware TX_DISABLE Negate Time
t_on
1
ms
Note 2
Time to initialize, including reset of TX_FAULT
t_init
300
ms
Note 3
Hardware TX_FAULT Assert Time
t_fault
100
µs
Note 4
Hardware TX_DISABLE to Reset
t_reset
µs
Note 5
Hardware RX_LOS DeAssert Time
t_loss_on
100
µs
Note 6
Hardware RX_LOS Assert Time
t_loss_off
100
µs
Note 7
Software TX_DISABLE Assert Time
t_off_soft
100
ms
Note 8
Software TX_DISABLE Negate Time
t_on_soft
100
ms
Note 9
Software Tx_FAULT Assert Time
t_fault_soft
100
ms
Note 10
Software Rx_LOS Assert Time
t_loss_on_soft
100
ms
Note 11
Software Rx_LOS De-Assert Time
t_loss_off_soft
100
ms
Note 12
Analog parameter data ready
t_data
1000
ms
Note 13
Serial bus hardware ready
t_serial
300
ms
Note 14
Write Cycle Time
t_write
10
ms
Note 15
Serial ID Clock Rate
f_serial_clock
400
kHz
10
Notes:
1. Time from rising edge of TX_DISABLE to when the optical output falls below 10% of nominal.
2. Time from falling edge of TX_DISABLE to when the modulated optical output rises above 90% of nominal.
3. Time from power on or falling edge of Tx_Disable to when the modulated optical output rises above 90% of nominal.
4. From power on or negation of TX_FAULT using TX_DISABLE.
5. Time TX_DISABLE must be held high to reset the laser fault shutdown circuitry.
6. Time from loss of optical signal to Rx_LOS Assertion.
7. Time from valid optical signal to Rx_LOS De-Assertion.
8. Time from two-wire interface assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the optical output falls below 10% of nominal. Measured
from falling clock edge after stop bit of write transaction.
9. Time from two-wire interface de-assertion of TX_DISABLE (A2h, byte 110, bit 6) to when the modulated optical output rises above 90% of
nominal.
10. Time from fault to two-wire interface TX_FAULT (A2h, byte 110, bit 2) asserted.
11. Time for two-wire interface assertion of Rx_LOS (A2h, byte 110, bit 1) from loss of optical signal.
12. Time for two-wire interface de-assertion of Rx_LOS (A2h, byte 110, bit 1) from presence of valid optical signal.
13. From power on to data ready bit asserted (A2h, byte 110, bit 0). Data ready indicates analog monitoring circuitry is functional.
14. Time from power on until module is ready for data transmission over the serial bus (reads or writes over A0h and A2h).
15. Time from stop bit to completion of a 1-8 byte write command.
12
Table 10. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics
(TC = -10°C to 85°C, VccT, VccR = 3.3 V ±10%)
Parameter
Symbol
Min.
Units
Notes
Transceiver Internal Temperature
TINT
±3.0
°C
Accuracy
Temperature is measured internal to the transceiver.
Valid from = -10°C to 85°C case temperature.
Transceiver Internal Supply
VINT
±0.1
V
Voltage Accuracy
Supply voltage is measured internal to the transceiver
and can, with less accuracy, be correlated to
voltage at the SFP Vcc pin. Valid over 3.3 V ± 10%.
Transmitter Laser DC Bias Current
Accuracy
IINT is better than ±10% of the nominal value.
IINT
±10
%
Transmitted Average Optical
PT
±3.0
dB
Output Power Accuracy
Coupled into 50/125 µm multi-mode fiber. Valid from
100 µW to 500 µW, avg.
Received Average Optical Input
PR
±3.0
dB
Power Accuracy
Coupled from 50/125 µm multi-mode fiber. Valid from
31 µW to 500 µW, avg.
VCCT,R > 2.97 V
VCCT,R > 2.97 V
TX_FAULT
TX_FAULT
TX_DISABLE
TX_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_init
t_init
t-init: TX DISABLE NEGATED
t-init: TX DISABLE ASSERTED
VCCT,R > 2.97 V
TX_FAULT
TX_FAULT
TX_DISABLE
TX_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_off
t_init
t_on
INSERTION
t-init: TX DISABLE NEGATED, MODULE HOT PLUGGED
t-off & t-on: TX DISABLE ASSERTED THEN NEGATED
OCCURANCE OF FAULT
OCCURANCE OF FAULT
TX_FAULT
TX_FAULT
TX_DISABLE
TX_DISABLE
TRANSMITTED SIGNAL
TRANSMITTED SIGNAL
t_fault
* SFP SHALL CLEAR TX_FAULT IN
< t_init IF THE FAILURE IS TRANSIENT
t-fault: TX FAULT ASSERTED, TX SIGNAL NOT RECOVERED
t_reset
t_init*
t-reset: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL RECOVERED
OCCURANCE OF FAULT
TX_FAULT
LOS
TRANSMITTED SIGNAL
t_fault
* SFP SHALL CLEAR TX_FAULT IN
< t_init IF THE FAILURE IS TRANSIENT
t_loss_on
t_reset
t_init*
t-fault: TX DISABLE ASSERTED THEN NEGATED, TX SIGNAL NOT RECOVERED
Figure 4. Transceiver timing diagrams (module installed except where noted).
13
OCCURANCE
OF LOSS
OPTICAL SIGNAL
TX_DISABLE
t-loss-on & t-loss-off
t_loss_off
Table 11. EEPROM Serial ID Memory Contents – Conventional SFP Memory (Address A0h)
Byte #
Data
Decimal Hex
Notes
Byte #
Decimal
Data
Hex
Notes
0
03
SFP physical device
37
00
Hex Byte of Vendor OUI[4]
1
04
SFP function defined by serial ID only
38
17
Hex Byte of Vendor OUI[4]
2
07
LC optical connector
39
6A
Hex Byte of Vendor OUI[4]
3
00
40
41
“A” - Vendor Part Number ASCII character
4
00
41
46
“F” - Vendor Part Number ASCII character
5
00
42
42
“B” - Vendor Part Number ASCII character
6
00
43
52
“R” - Vendor Part Number ASCII character
7
20
Intermediate distance (per FC-PI)
44
2D
“-” - Vendor Part Number ASCII character
8
40
Shortwave laser without OFC (open fiber control)
45
35
“5” - Vendor Part Number ASCII character
9
0C
Multi-mode 50 µm and 62.5 µm optical media
46
37
“7” - Vendor Part Number ASCII character
10
05
100 & 200 Mbytes/sec FC-PI speed[1]
47
4D
“M” - Vendor Part Number ASCII character
11
01
Compatible with 8B/10B encoded data
48
35
“5” - Vendor Part Number ASCII character
12
15
2100 MBit/sec nominal bit rate (2.125 Gbit/s)
49
41
“A” - Vendor Part Number ASCII character
13
00
50
50
“P” - Vendor Part Number ASCII character
14
00
51
5A
“Z” - Vendor Part Number ASCII character
15
00
52
20
“ ” - Vendor Part Number ASCII character
16
1E
300 m of 50/125 µm fiber @ 2.125GBit/sec[2]
53
20
“ ” - Vendor Part Number ASCII character
17
0F
150 m of 62.5/125 µm fiber @ 2.125GBit/sec[3]
54
20
“ ” - Vendor Part Number ASCII character
18
00
55
20
“ ” - Vendor Part Number ASCII character
19
00
56
20
“ ” - Vendor Part Number ASCII character
20
41
“A” - Vendor Name ASCII character
57
20
“ ” - Vendor Part Number ASCII character
21
56
“V” - Vendor Name ASCII character
58
20
“ ” - Vendor Part Number ASCII character
22
41
“A” - Vendor Name ASCII character
59
20
“ ” - Vendor Part Number ASCII character
23
47
“G” - Vendor Name ASCII character
60
03
Hex Byte of Laser Wavelength[5]
24
4F
“O” - Vendor Name ASCII character
61
52
Hex Byte of Laser Wavelength[5]
25
20
“ ” - Vendor Name ASCII character
62
00
26
20
“ ” - Vendor Name ASCII character
63
27
20
“ ” - Vendor Name ASCII character
64
Checksum for Bytes 0-62[6]
00
28
20
“ ” - Vendor Name ASCII character
65
1A
Hardware SFP TX_DISABLE, TX_FAULT,
& RX_LOS
29
20
“ ” - Vendor Name ASCII character
66
00
30
20
“ ” - Vendor Name ASCII character
67
00
31
20
“ ” - Vendor Name ASCII character
68-83
Vendor Serial Number ASCII characters[7]
32
20
“ ” - Vendor Name ASCII character
84-91
Vendor Date Code ASCII characters[8]
33
20
“ ” - Vendor Name ASCII character
92
Digital Diagnostics, Internal Cal, Rx Pwr Avg
68
34
20
“ ” - Vendor Name ASCII character
93
F0
A/W, Soft SFP TX_DISABLE, TX_FAULT,
& RX_LOS
35
20
SFF-8472 Compliance to revision 9.3
36
00
“ ” - Vendor Name ASCII character
94
01
95
96 - 255
Checksum for Bytes 64-94[6]
00
Notes:
1. FC-PI speed 100 MBytes/sec is a serial bit rate of 1.0625 GBit/sec. 200 MBytes/sec is a serial bit rate of 2.125 GBit/sec.
2. Link distance with 50/125 µm cable at 1.0625 GBit/sec is 500 m. Link distance at 2.125 GBit/sec is 300 m.
3. Link distance with 62.5/125 µm cable at 1.0625 GBit/sec is 300 m. Link distance with 62.5/125 µm cable at 2.125 GBit/sec is 150 m.
4. The IEEE Organizationally Unique Identifier (OUI) assigned to Avago Technologies is 00-17-6A (3 bytes of hex).
5. Laser wavelength is represented in 16 unsigned bits. The hex representation of 850 (nm) is 0352.
6. Addresses 63 and 95 are checksums calculated (per SFF-8472 and SFF-8074) and stored prior to product shipment.
7. Addresses 68-83 specify the AFBR-57M5APZ ASCII serial number and will vary on a per unit basis.
8. Addresses 84-91 specify the AFBR-57M5APZ ASCII date code and will vary on a per date code basis.
14
Table 12. EEPROM Serial ID Memory Contents – Enhanced Feature Set Memory (Address A2h)
Byte #
Decimal Notes
Byte #
Decimal Notes
Byte #
Decimal
Notes
104
Real Time Rx Pwr MSB[5]
0
Temp H Alarm MSB[1]
26
Tx Pwr L Alarm MSB[4]
1
Temp H Alarm LSB[1]
27
Tx Pwr L Alarm LSB[4]
105
Real Time Rx Pwr LSB[5]
2
Temp L Alarm MSB[1]
28
Tx Pwr H Warning MSB[4]
106
Reserved
3
Temp L Alarm LSB[1]
29
Tx Pwr H Warning LSB[4]
107
Reserved
4
Temp H Warning MSB[1]
30
Tx Pwr L Warning MSB[4]
108
Reserved
5
Temp H Warning LSB[1]
31
Tx Pwr L Warning LSB[4]
109
Reserved
6
Temp L Warning MSB[1]
32
Rx Pwr H Alarm MSB[5]
110
Status/Control - See
Table 14
7
Temp L Warning LSB[1]
33
Rx Pwr H Alarm LSB[5]
8
Vcc H Alarm MSB[2]
111
Reserved
34
Rx Pwr L Alarm MSB[5]
9
Vcc H Alarm LSB[2]
112
Flag Bits - See Table 15
35
Rx Pwr L Alarm LSB[5]
10
Vcc L Alarm MSB[2]
113
Flag Bits - See Table 15
36
Rx Pwr H Warning MSB[5]
11
Vcc L Alarm LSB[2]
114
Reserved
37
Rx Pwr H Warning LSB[5]
12
Vcc H Warning MSB[2]
115
Reserved
38
Rx Pwr L Warning MSB[5]
13
Vcc H Warning LSB[2]
116
Flag Bits - See Table 15
39
Rx Pwr L Warning LSB[5]
14
Vcc L Warning MSB[2]
117
Flag Bits - See Table 15
15
Vcc L Warning LSB[2]
40-55
Reserved
118-127
Reserved
56-94
External Calibration Constants[6]
16
Tx Bias H Alarm MSB[3]
128-247
Customer Writeable
95
Checksum for Bytes 0-94[7]
248-255
Vendor Specific
17
Tx Bias H Alarm LSB[3]
96
Real Time Temperature MSB[1]
18
Tx Bias L Alarm MSB[3]
97
Real Time Temperature LSB[1]
19
Tx Bias L Alarm LSB[3]
98
Real Time Vcc MSB[2]
20
Tx Bias H Warning MSB[3]
99
Real Time Vcc LS[2]
21
Tx Bias H Warning LSB[3]
100
Real Time Tx Bias MSB[3]
22
Tx Bias L Warning MSB[3]
101
Real Time Tx Bias LSB[3]
23
Tx Bias L Warning LSB[3]
102
Real Time Tx Power MSB[4]
24
Tx Pwr H Alarm MSB[4]
103
Real Time Tx Power LSB[4]
25
Tx Pwr H Alarm LSB[4]
Notes:
1. Temperature (Temp) is decoded as a 16 bit signed twos compliment integer in increments of 1/256°C.
2. Supply Voltage (Vcc) is decoded as a 16 bit unsigned integer in increments of 100 µV.
3. Laser bias current (Tx Bias) is decoded as a 16 bit unsigned integer in increments of 2 µA.
4. Transmitted average optical power (Tx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 µW.
5. Received average optical power (Rx Pwr) is decoded as a 16 bit unsigned integer in increments of 0.1 µW.
6. Bytes 56-94 are not intended for use with AFBR-57M5APZ, but have been set to default values per SFF-8472.
7. Byte 95 is a checksum calculated (per SFF-8472) and stored prior to product shipment.
15
Table 13. EEPROM Serial ID Memory Contents – Soft Commands (Address A2h, Byte 110)
Bit #
Status/
Control Name
Description
Notes
7
TX_ DISABLE State
Digital state of SFP TX_ DISABLE Input Pin (1 = TX_DISABLE asserted)
Note 1
6
Soft TX_ DISABLE
Read/write bit for changing digital state of TX_DISABLE function
Note 1, 2
5
Reserved
4
Reserved
3
Reserved
2
TX_FAULT State
Digital state of the SFP TX_FAULT Output Pin (1 = TX_FAULT asserted)
Note 1
1
RX_LOS State
Digital state of the SFP RX_LOS Output Pin (1 = RX_LOS asserted)
Note 1
0
Data Ready (Bar)
Indicates transceiver is powered and real time sense data is ready. (0 = Ready)
Note 3
Notes:
1. The response time for soft commands of the AFBR-57M5APZ is 100 msec as specified by the MSA SFF-8472.
2. Bit 6 is logic OR’d with the SFP TX_DISABLE input pin 3 ... either asserted will disable the SFP transmitter.
3. AFBR-57M5APZ meets the MSA SFF-8472 data ready timing of 1000 msec.
4. Status bits do not impact optical performance.
Table 14. EEPROM Serial ID Memory Contents – Alarms and Warnings (Address A2h, Bytes 112, 113, 116, 117)
Byte
Bit
Flag Bit Name Description
112
113
116
117
7
Temp High Alarm
Set when transceiver internal temperature exceeds high alarm threshold
6
Temp Low Alarm
Set when transceiver internal temperature exceeds low alarm threshold
5
Vcc High Alarm
Set when transceiver internal supply voltage exceeds high alarm threshold
4
Vcc Low Alarm
Set when transceiver internal supply voltage exceeds low alarm threshold
3
Tx Bias High Alarm
Set when transceiver laser bias current exceeds high alarm threshold
2
Tx Bias Low Alarm
Set when transceiver laser bias current exceeds low alarm threshold
1
Tx Power High Alarm
Set when transmitted average optical power exceeds high alarm threshold
0
Tx Power Low Alarm
Set when transmitted average optical power exceeds low alarm threshold
7
Rx Power High Alarm
Set when received average optical power exceeds high alarm threshold
6
Rx Power Low Alarm
Set when received average optical power exceeds low alarm threshold
0-5
Reserved
7
Temp High Warning
Set when transceiver internal temperature exceeds high warning threshold
6
Temp Low Warning
Set when transceiver internal temperature exceeds low warning threshold
5
Vcc High Warning
Set when transceiver internal supply voltage exceeds high warning threshold
4
Vcc Low Warning
Set when transceiver internal supply voltage exceeds low warning threshold
3
Tx Bias High Warning
Set when transceiver laser bias current exceeds high warning threshold
2
Tx Bias Low Warning
Set when transceiver laser bias current exceeds low warning threshold
1
Tx Power High Warning
Set when transmitted average optical power exceeds high warning threshold
0
Tx Power Low Warning
Set when transmitted average optical power exceeds low warning threshold
7
Rx Power High Warning
Set when received average optical power exceeds high warning threshold
6
Rx Power Low Warning
Set when received average optical power exceeds low warning threshold
0-5
Reserved
Note: Alarm and warning bits do not latch nor do they impact optical performance.
16
55.3 ± 0.2
AFBR-57M5APZ
850nm LASER PROD
21CRF(J) CLASS1
SINGAPORE 0446
PPOC-4102-DIn2 SN: AJ0446CD1C
13.6
Z
5AP OD
7M PR
R-5 ASERASS1
AFB 50nmRLF(J) C0L44545CD1C
DEVICE SHOWN WITH
DUST CAP AND
BAIL DELATCH
13.4 ± 0.1
1.91
8 21C INA 04
CHSN: A3
2
-Din
02
-44
G
PPO
1.39 UNCOMPRESSED
12.4 ± 0.2
8.5 ± 0.1
0.55 UNCOMPRESSED
6.25 ± 0.05
+ 0.2
13.6 0
TX
RX
14.9 UNCOMPRESSED
Figure 5. Module drawing.
17
X
Y
34.5
10
3x
7.1
8.58
∆ 0.85 0.05
∆ 0.1 S X Y
A
1
2.5
1
2.5
B
PCB
EDGE
11.08
16.25
REF. 14.25
7.2
10x ∆1.05 0.01
∆ 0.1 L X A S
16.25
MIN. PITCH
3.68
5.68
20
PIN 1
2x 1.7
8.48
9.6
4.8
11
10
11.93
SEE DETAIL 1
2.0
11x
11x 2.0
9x 0.95 0.05
∆ 0.1 L X A S
5
26.8
10
3x
3
2
41.3
42.3
3.2
5
0.9
PIN 1
LEGEND
20
10.53
10.93
9.6
20x 0.5 0.03
0.06 L A S B S
0.8
TYP.
10
11.93
2 0.005 TYP.
0.06 L A S B S
DETAIL 1
Figure 6. SFP host board mechanical layout.
18
PADS AND VIAS ARE CHASSIS GROUND
2.
THROUGH HOLES, PLATING OPTIONAL
3.
HATCHED AREA DENOTES COMPONENT
AND TRACE KEEPOUT (EXCEPT
CHASSIS GROUND)
4.
AREA DENOTES COMPONENT
KEEPOUT (TRACES ALLOWED)
11
4
2x 1.55 0.05
∆ 0.1 L A S B S
1.
DIMENSIONS ARE IN MILLIMETERS
1.7 ± 0.9
3.5 ± 0.3
41.78 ± 0.5
Tcase REFERENCE POINT
CAGE ASSEMBLY
15 MAX.
11.73 REF
15.25 ± 0.1
9.8 MAX.
10 REF
(to PCB)
10.4 ± 0.1
PCB
0.4 ± 0.1
(below PCB)
16.25 ± 0.1 MIN. PITCH
DIMENSIONS ARE IN MILLIMETERS
Figure 7. SFP Assembly drawing.
Customer Manufacturing Processes
This module is pluggable and is not designed for aqueous wash, IR reflow, or wave soldering processes.
For product information and a complete list of distributors, please go to our website:
www.avagotech.com
Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries.
Data subject to change. Copyright © 2005-2013 Avago Technologies. All rights reserved. Obsoletes AV01-0276EN
AV02-3804EN - January 23, 2013