8 Pin DIP and SMD Single Output Low Power / Low Noise 3.3V Application TTL Compatible Active Delay Lines Compatible with standard auto-insertable equipment and can be used in either infrared or vapor phase process. TIME DELAY (ns) ± 5% or ± 2 nS† 5 7 10 12 15 20 25 30 35 40 45 PART NUMBER (DIP) PART NUMBER (SMD) EPA3856-5 EPA3856-7 EPA3856-10 EPA3856-12 EPA3856-15 EPA3856-20 EPA3856-25 EPA3856-30 EPA3856-35 EPA3856-40 EPA3856-45 EPA3856G-5 EPA3856G-7 EPA3856G-10 EPA3856G-12 EPA3856G-15 EPA3856G-20 EPA3856G-25 EPA3856G-30 EPA3856G-35 EPA3856G-40 EPA3856G-45 †Whichever is greater. High-Level Output Voltage 50 60 75 100 120 125 150 175 200 225 250 VCC = 2.7 to 3.6 V;I OH = -100µA VCC -0.2 V VCC = 2.7 V;I OH = -6mA 2.4 V VCC = 3.0 V;I OH = -20mA 2.0 V 0.5 V VCC = 3.0 V;I OL = 32mA 0.5 V VCC = 2.7 V;I IK = -18mA -1.2 V I CCH Quiescent Supply Current VCC = 3.6 V; OH,VI = Gnd or V CC ,I O =0 TBA mA I CCL Quiescent Supply Current VCC = 3.6 V; OL ,VI = Gnd or V CC ,I O =0 TBA mA Input Clamp Voltage VCC = 2.7 V;I OL = -100µA 5 OUTPUT VCC INPUT 1 4 GROUND Input Pulse Test Conditions @ 25° C Recommended Operating Conditions VCC VIH VIL IIK IOH IOL PW* d* TA EPA3856G-50 EPA3856G-60 EPA3856G-75 EPA3856G-100 EPA3856G-120 EPA3856G-125 EPA3856G-150 EPA3856G-175 EPA3856G-200 EPA3856G-225 EPA3856G-250 8 V VIK EPA3856-50 EPA3856-60 EPA3856-75 EPA3856-100 EPA3856-120 EPA3856-125 EPA3856-150 EPA3856-175 EPA3856-200 EPA3856-225 EPA3856-250 Schematic 0.2 Low-Level Output Voltage PART NUMBER (SMD) Max Unit Min VCC = 2.7 V;I OL = 24mA VOL PART NUMBER (DIP) Delay Times referenced from input to leading edges at 25°C, 3.0V, with no load. DC Electrical Characteristics Parameter Test Conditions VOH TIME DELAY (ns) ± 5% or ± 2 nS† Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature Min Max Unit 2.7 3.6 2.0 0.8 -20 -20 32 V V V mA mA mA % % °C 40 40 +70 0 EIN PW TRI PRR VCC Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage Unit 3.2 110 2.0 1.0 100 3.0 Volts % nS MHz KHz Volts *These two values are inter-dependent. SMD Package DIP Package .300 .300 PCA EPA3856-5 Date Code .055 PCA EPA3856G-5 Date Code .280 MAX Suggested Solder .410 Pad Layout .03 DSA3856(G)-XX .020 TYP .250 MAX .490 .02 WHITE DOT PIN#1 .500 MAX WHITE DOT PIN#1 .240 .280 MAX .01 TYP .020 TYP .05 .100 TYP .365 MAX .010 TYP .300 Rev. 1 2/4/02 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 .XX = ± .030 .XXX = ± .010 .120 MIN . QAF-CSO1 Rev. B 8/25/94 ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791