AZ6961 10 AMP SUBMINIATURE POWER RELAY FEATURES • • • • • • • • High sensitivity, 120 mW pickup Dielectric strength 5000 Vrms Isolation spacing greater than 8 mm 10 Amp switching capability Epoxy sealed version available Reinforced insulation, EN 60730-1 (VDE 0631, part 1) UL, CUR file E43203 VDE file 131637 CONTACTS GENERAL DATA Arrangement SPDT (1 Form C) SPST (1 Form A) Ratings Resistive load: Max. switched power: 240 W or 2500 VA Max. switched current: 10 A Max. switched voltage: 240* VDC or 440 VAC Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 8 A 250 VAC res. Operate Time (typical) 7 ms at nominal coil voltage Release Time (typical) 3 ms at nominal coil voltage (with no coil suppression) * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Rated Load UL, CUR VDE 10 A at 250 VAC resistive [1] 8 A at 30 VDC / 250 VAC [1] 8 A at 30 VDC / 250 VAC, 100k cycles [2] B300 Pilot Duty [1] R300 Pilot Duty [1] 8 A at 250 VAC resistive, [1], [2] and [3] [1] Silver cadmium oxide, [2] Silver tin oxide, [3] Silver nickel Material Silver cadmium oxide, silver tin oxide or silver nickel, gold plating available Resistance < 100 milliohms initially COIL Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Insulation (according to DIN VDE 0110, IEC 60664-1) C250 Overvoltage category: III Pollution degree: 3 Nominal voltage: 250 VAC Dropout Greater than 10% of nominal coil voltage Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) Vibration Break Contact: 5 g at 10 …500 Hz Make Contact: 20 g at 10…500 Hz Shock 10 g Enclosure P.B.T. polyester, UL94 V-O Terminals Tinned copper alloy, P.C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Power At Pickup Voltage (typical) 120 mW 140 mW (60 VDC coil) Max. Continuous Dissipation 1.2 W at 20°C (68°F) ambient Temperature Rise 20°C (36°F) at nominal coil voltage Max. Solvent Temp. 80°C (176°F) Max. 130°C (266°F) Max. Immersion Time 30 seconds Weight 8 grams Packing unit in pcs 20 per plastic tube / 1000 per carton box Temperature NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2004-07-29 AZ6961 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 5 Must Operate VDC 3.5 Max. Continuous VDC 11.6 6 4.2 14.0 ORDER NUMBER* Coil Resistance Ohm 113 ± 10% 164 ± 10% 1 Form A (SPST-NO) AZ6961–1A–5D 1 Form C (SPDT) AZ6961–1C–5D AZ6961–1A–6D AZ6961–1C–6D 9 6.3 21.1 360 ± 10% AZ6961–1A–9D AZ6961–1C–9D 12 8.4 27.2 617 ± 10% AZ6961–1A–12D AZ6961–1C–12D 15 10.5 38.0 800 ± 10% AZ6961–1A–15D AZ6961–1C–15D 24 16.8 53.1 2,350 ± 10% AZ6961–1A–24D AZ6961–1C–24D 48 33.6 107.3 9,600 ± 15% AZ6961–1A–48D AZ6961–1C–48D 60 42.0 122.4 12,500 ± 15% AZ6961–1A–60D AZ6961–1C–60D * Add suffix “E” to “1A” or “1C” for silver tin oxide contacts. Add suffix “B” to “1A” or “1C” for silver nickel contacts. Add suffix “E” at the end of order number for sealed version. Add suffix “A” for gold plated contacts. MECHANICAL DATA Coil Temperature Rise FORM C VERSION PC BOARD LAYOUT .408 Max. [10.35] [28.75] .494 Max. [12.55] .012 [0.3] .298 [7.56] .050 [1.3] 1 FORM C .126 [3.2] .126 [3.2] .142 [3.6] 3 x .016 [0.4] 2 x ø .020 [ø 0.5] .062 [1.57] .870 [22.1] 5 x ø .051 [ø 1.3] 3 x .031 [0.8] .116 [2.95] .744 [18.9] 4 x ø .051 [ø 1.3] Coil Temperature Rise °C 1.132 Max. 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0 10A 0A 60% .298 [7.56] 1 FORM A 80% 100% 120% 140% 160% 180% 200% 220% Percent of Nominal Coil Voltage at 20°C .050 [1.3] .198 [5.04] VIEWED TOWARD TERMINALS FORM A VERSION Maximum Switching Capacity CIRCUIT DIAGRAM 1.132 Max. .408 Max. [10.35] [28.75] 10.0 1 .494 Max. [12.55] 9.0 8.0 7.0 6.0 5.0 4 1 FORM C DC Resistive Load 4.0 3.0 .012 [0.3] 2 x ø .020 [ø 0.5] 3 5 .142 [3.6] 2 x .016 [0.4] 2 x .031 [0.8] 1 AC Resistive Load 2.0 CURRENT 2 1.0 .9 .8 .7 .6 .5 .4 3 .3 1 FORM A 400 500 600 700 800 900 300 200 100 40 50 60 70 80 90 30 1000 VIEWED TOWARD TERMINALS .1 20 4 10 2 .2 VOLTAGE Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Junkersstrasse 3, D-82178 Puchheim, Germany Tel. +49 89 800 97 0 Fax +49 89 800 97 200 [email protected] www.ZETTLERelectronics.com 2004-07-29