ER1AA - ER1JA SURFACE MOUNT SUPER FAST RECTIFIER DIODES VOLTAGE RANGE: 50 - 600V CURRENT: 1.0 A Features ! Glass Passivated Die Construction ! Ideally Suited for Automatic Assembly ! Low Forward Voltage Drop, High Efficiency ! Low Power Loss ! Super-Fast Recovery Time B SMA(DO-214AC) ! Plastic Case Material has UL Flammability Classification Rating 94V-O Dim Min Max Mechanical Data ! ! ! ! ! A Case: SMA/DO-214AC, Molded Plastic Terminals: Solder Plated, Solderable per MIL-STD-750, Method 2026 Polarity: Cathode Band or Cathode Notch Marking: Type Number Weight: 0.064 grams (approx.) C D J G E H Maximum Ratings and Electrical Characteristics A 2.29 2.92 B 4.00 4.60 C 1.27 1.63 D 0.15 0.31 E 4.80 5.59 G 0.10 0.20 H 0.76 1.52 J 2.01 2.62 All Dimensions in mm TA = 25C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Symbol Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current ER1EA ER1GA ER1JA Unit VRRM VRWM VR 50 100 150 200 300 400 600 V VR(RMS) 35 70 105 140 210 280 420 V IO 1.0 A Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave superimposed on rated load (JEDEC Method) IFSM 30 A Forward Voltage @IF = 1.0A VFM @TA = 25°C @TA = 100°C IRM 5.0 500 µA Reverse Recovery Time (Note 1) trr 35 nS Typical Junction Capacitance (Note 2) Cj 10 pF RJL 34 K/W Tj, TSTG -65 to +150 °C Peak Reverse Current At Rated DC Blocking Voltage @TL = 100°C ER1AA ER1BA ER1CA ER1DA Typical Thermal Resistance (Note 3) Operating and Storage Temperature Range 0.95 1.25 1.7 V Note: 1. Measured with IF = 0.5A, IR = 1.0A, Irr = 0.25A, 2. Measured at 1.0 MHz and applied reverse voltage of 4.0 V DC. 3. Mounted on P.C. Board with 8.0mm2 land area. 1 of 2 www.sunmate.tw IF, INSTANTANEOUS FORWARD CURRENT (A) Tj = 25°C Pulse width = 300µs 10 ER1EA - ER1GA ER1AA - ER1DA 1.0 ER1JA 0.1 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 30 100 Tj = 25°C f = 1.0MHz Pulse width 8.3 ms single half-sine-wave (JEDEC method) Cj, CAPACITANCE (pF) IFSM, PEAK FORWARD SURGE CURRENT (A) VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 2 Typical Forward Characteristics 20 10 10 1 0 1 10 NUMBER OF CYCLES AT 60Hz Fig. 3 Peak Forward Surge Current 100 1 10 100 VR, REVERSE VOLTAGE (V) Fig. 4 Typical Junction Capacitance trr +0.5A 50Ω NI (Non-inductive) 10Ω NI Device Under Test (-) 0A (+) Pulse Generator (Note 2) 50V DC Approx (-) 1.0Ω NI Oscilloscope (Note 1) -0.25A (+) Notes: 1. Rise Time = 7.0ns max. Input Impedance = 1.0MΩ, 22pF. 2. Rise Time = 10ns max. Input Impedance = 50Ω. -1.0A Set time base for 5/10ns/cm Fig. 5 Reverse Recovery Time Characteristic and Test Circuit 2 of 2 www.sunmate.tw