Click on Series name for product info on aimtec.com Series AME2-NJZ 2 Watt | AC-DC / DC-DC Converter FEATURES: Picture coming soon Models Single output Model Input Voltage (VAC/Hz) AME2-5SNJZ AME2-12SNJZ AME2-24SNJZ 165-264/47-63 165-264/47-63 165-264/47-63 Input Specifications Parameters Current (full load) Inrush current <2ms (cold start) Leakage current External fuse Output Specifications Parameters Voltage accuracy Line regulation Load regulation Minimum load Ripple & Noise Hold up time Isolation Specifications Parameters Tested I/O voltage Isolation Resistance General Specifications Parameters Switching frequency Over Current protection Short circuit protection Operating temperature* Storage temperature Temperature coefficient Maximum Case temperature Humidity Case material Weight Cooling Dimensions (L x W x H) MTBF I/O Isolation 3000VAC Operating Temp: -40°C to +70°C Input: 165-264VAC, 47-63Hz, or 233-370 VDC No internal electrolytic capacitors Longer product life Class II Power supply Low no load consumption ≤ 0.3W Continuous Short Circuit Protection Over current Protection Input Voltage (VDC) Temperature range (ºC) Output Voltage (V) Output Current max (mA) Maximum capacitive Load (µF) Efficiency (%) 233-370 233-370 233-370 -40 to +70 -40 to +70 -40 to +70 5 12 24 400 167 83 3000 1000 220 70 76 78 Conditions Typical 165 VAC 230 VAC 165 VAC 230 VAC 230VAC/50Hz, rms Recommended slow blow type 30 25 Typical Full Load LL-HL, Full Load 10% - 100% load, nominal input ±2 ±1 ±1 10 50 8 16 Conditions Typical 60 sec Auto recovery No derating Typical Units Maximum Units 150 % % % % mV p-p ms Rated Units 3000 VAC MΩ >1000 Conditions VAC mA mA A A mA A 6 10 0.1 2 Conditions 20MHz bandwidth 165VAC 230VAC Maximum 230 Maximum 115 ≥110 Hiccup, Auto recovery, Continuous -40 to +70 -40 to +105 ±0.01 Units KHz % of Iout 100 Non condensing 95 Plastic resin (flammability to UL 94V-0) 25 Free air convection 1.46 x 0.96 x 0.71 (37.00 x 24.50 x 18.00mm) > 300,000 hrs (MIL-HDBK -217F, t=+25oC)/Full Load °C °C %/°C °C % RH g NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. * Sufficient air space around is needed. www.aimtec.com F 052e R8 Tel: +1 514 620 2722 1 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AME2-NJZ 2 Watt | AC-DC / DC-DC Converter Safety Specifications Parameters Pin Out Specifications Pin Single Dimensions 5.08 (0.20) 37.00 (1.46) AC Input (L) AC Input (N) -V Output +V Output +V Cap -V Cap 1 24.50 (0.97) 1 3 14 16 20 22 IEC/EN/UL 60950-1 EN55022, class B IEC 61000-4-2, Contact:±6KV/Air:±8KV, Criteria B IEC 61000-4-3, 10V/m, Criteria A IEC 61000-4-4, ±2KV, Criteria B, with application circuit IEC 61000-4-5, ±1KV/±2KV, Criteria B, with application circuit IEC 61000-4-6, 10Vrms, Criteria A IEC 61000-4-8, 10A/m, Criteria A IEC 61000-4-11, 0-70%, Criteria B 3 17.78 (0.70) Standards Information technology Equipment EMI - Conducted and radiated emission Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient/Burst Immunity Surge Immunity(1KV) RF, Conducted Disturbance Immunity Power frequency Magnetic Field Immunity Voltage dips, Short Interruptions Immunity Bottom View 22 5.08 (0.20) 20 16 10.16 (0.40) 14 5.08 (0.20) 18.00 (0.71) Printed Face All dimensions are typical: millimeters (inches) Pin Diameter: 0.60 ± 0.10 (0.02 ± 0.004) Case Tolerance: ± 0.5 (±0.02) 4.10 (0.16) 0.60 (0.02) Application circuit for Vin: 165-264VAC Single Output FUSE 1A/250V AC L AC L 20 22 AC N AC AC N + Vout + Vout DC + TVS C1 C2 1µF/50V ‐ Vout ‐ Vout *GND connection not allowed www.aimtec.com F 052e R8 Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AME2-NJZ 2 Watt | AC-DC / DC-DC Converter Application circuit for Vin: 85-264VAC Single Output FUSE 1A/250V + Vout + Vout AC L AC L 20 + C3 AC + DC C1 C2 1µF/50V 22 AC N AC N TVS ‐ Vout ‐ Vout *GND connection not allowed Model 5 Vout 12 Vout 24 Vout C2 100 µF / 35V 68 µF / 35V 47 µF / 35V C3 4.7 µF / 400V TVS 7V 20V 30V NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 052e R8 Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only