Panasonic ERU5TCK6R8 Wirewound resistor with ther mal cut-off Datasheet

Wirewound Resistor with Thermal Cut-offs
Wirewound Resistor with Thermal Cut-offs
Type:
ERU5T
■ Features
●
●
●
●
Accurate fusing characteristics
Low cost and easy handling
Space saving design
Excellent anti-surge characteristics
■ Recommended Applications
● Switching regulators, video adapters, safety circuits
■ Explanation of Part Numbers
Product Code
Fusing
Resistors
1
2
3
4
5
6
7
8
9
10
E
R
U
5
T
B
K
6
R
8
Element
Code
Power
5
5 W type
Code
T
Style
Style
Radial
Insertion
Type
Code
B
C
Thermal Cut-offs
Voltage Current Temp.
250 V
2A
134 °C
250 V
2A
145 °C
Resistance
Tolerance
Code
Tol.
J
± 5%
K
±10 %
Standard
Resistance
Tolerance
10 액< : J
<10 액 : K
Resistance Value
The first two digits are
significant figures of resistance
and the third one denotes
number of zeros following.
Decimal point is expressed
by R as 6.8=6R8
■ Ratings
Code
Power Rating
(W)
Current Rating
(A)
Thermal Cut-off Resistance Range Standard Quantity
(액)
(pcs.)
(°C)
B
1.6
2
134
0.18 to 680
500
6.5
C
1.8
2
145
0.18 to 680
500
6.5
120
25 °C
100
Rated Load (%)
Power Derating Curve
For resistors operated in ambient temperatures above
25 °C, power rating shall be derated in accordance
with the figure on the right.
Mass (Weight)
[g/pc.]
80
60
40
5TB
5TC
20
0
–40 –20
90 °C
0
20
40
60
80
100 120 140 160
Ambient Temperature (°C)
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Feb. 2006
Wirewound Resistor with Thermal Cut-offs
■ Dimensions in mm (not to scale)
9±1
f0.6±0.1
4.5 –1.0
f0.8±0.1
+2.0
25.5±1.5
13±1
+2
5 –1
■ Fusing Characteristics
ERU5TBK6R8
ERU5TBK5R1
1000
1000
(Thermal Cutoff)
Fusing Time (s)
Fusing Time (s)
(Thermal Cutoff)
100
10
1
100
10
1
(Wirewound)
1
(Wirewound)
3 10 30 100 300 1000
Applied Load (W)
1
3 10 30 100 300 1000
Applied Load (W)
ERU5TBJ150
ERU5TBJ100
1000
1000
(Thermal Cutoff)
Fusing Time (s)
Fusing Time (s)
(Thermal Cutoff)
100
10
100
10
1
1
(Wirewound)
1
3 10 30 100 300 1000
Applied Load (W)
(Wirewound)
1
3 10 30 100 300 1000
Applied Load (W)
■ Packaging Methods
Please contact the factory for packaging methods.
Safety Precautions
The following are precautions for individual products. Please also refer to the precautions common to Fixed Resistors
shown on page ER3 of this catalog.
1. When voltage exceeds the rated voltage and/or a current exceeds the rated current and are continuously applied,
the element of Wirewound Resistor with Thermal Cutoffs (hereafter called the resistors) produces excessive heat,
which may not only deteriorate the built-in the Thermal Cutoffs but also blow it.
2. The resistors have a built-in the Thermal Cutoffs. Therefore, use and store them within their respective operating
and storing temperature ranges as specified in individual delivery specifications.
3. Carefully check the inductance effect of the resistors when using them in a high-frequency circuit.
4. If a transient load (heavy load in a short time) like a pulse is expected to be applied, check and evaluate the
operations of the resistors when installed in your products under the most adverse conditions before use.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
Feb. 2006
Safety Precautions
(Common precautions for Fixed Resistors)
• When using our products, no matter what sort of equipment they might be used for, be sure to make a written
agreement on the specifi cations with us in advance. The design and specifi cations in this catalog are subject
to change without prior notice.
• Do not use the products beyond the specifications described in this catalog.
• This catalog explains the quality and performance of the products as individual components. Before use, check
and evaluate their operations when installed in your products.
• Install the following systems for a failsafe design to ensure safety if these products are to be used in equipment
where a defect in these products may cause the loss of human life or other significant damage, such as damage to
vehicles (au to mo bile, train, vessel), traffi c lights, medical equipment, aerospace equipment, elec tric heating
appliances, combustion/gas equipment, rotating equipment, and disaster/crime prevention equipment.
✽ Systems equipped with a protection circuit and a protection device
✽ Systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault
(1) Precautions for use
• These products are designed and manufactured for general and stan dard use in general elec tron ic
equipment (e.g. AV equipment, home electric ap plianc es, offi ce equipment, information and com mu ni cation
equipment)
• These products are not intended for use in the following special conditions. Before using the products, carefully
check the effects on their quality and performance, and determine whether or not they can be used.
1. In liquid, such as water, oil, chemicals, or organic solvent
2. In direct sunlight, outdoors, or in dust
3. In salty air or air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
4. Electric Static Discharge (ESD) Environment
These components are sensitive to static electricity and can be damaged under static shock (ESD).
Please take measures to avoid any of these environments.
Smaller components are more sensitive to ESD environment.
5. Electromagnetic Environment
Avoid any environment where strong electromagnetic waves exist.
6. In an environment where these products cause dew condensation
7. Sealing or coating of these products or a printed circuit board on which these products are mounted, with resin
or other materials
• These products generate Joule heat when energized. Carefully position these products so that their heat will not
affect the other components.
• Carefully position these products so that their temperatures will not exceed the category temperature range due
to the effects of neighboring heat-generating components. Do not mount or place heat-generating components or
inflammables, such as vinyl-coated wires, near these products .
• Note that non- cleaning solder, halogen-based highly active fl ux, or water-soluble fl ux may deteriorate the
performance or reliability of the products.
• Carefully select a fl ux cleaning agent for use after soldering. An unsuitable agent may deteriorate the
performance or reliability. In particular, when using water or a water-soluble cleaning agent, be careful not to leave
water residues. Otherwise, the insulation performance may be deteriorated.
(2) Precautions for storage
The performance of these products, including the solderability, is guaranteed for a year from the date of arrival at your
company, provided that they remain packed as they were when delivered and stored at a temperature of 5 °C to 35 °
C and a relative humidity of 45 % to 85 %.
Even within the above guarantee periods, do not store these products in the following conditions. Otherwise, their
electrical performance and/or solderability may be deteriorated, and the packaging materials (e.g. taping materials)
may be deformed or deteriorated, resulting in mounting failures.
1. In salty air or in air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
2. In direct sunlight
<Package markings>
Package markings include the product number, quantity, and country of origin.
In principle, the country of origin should be indicated in English.
Feb. 2006
– ER3 –
Similar pages