ACT ACTF4014 If filter Datasheet

Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
The ACTF4014/480.0/QCC8C is an IF filter for DBS receivers with constant group
delay. The device is housed in a QCC8C package. Centre frequency ; 480.0MHz.
1.Package Dimension (QCC8C)
2.
Pin
Connection
2
Input
1
Input Ground
6
Output
5
Output Ground
3, 7
To be Grounded
4,8
Case Ground
Sign
Data (unit: mm)
Sign
Data (unit: mm)
A
2.08
E
1.20
B
0.60
F
1.35
C
1.27
G
5.00
D
2.54
H
5.00
3.Equivalent LC Model
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
Issue : 1.1 C1
Date : March 2010
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
4.Typical Frequency Response
5.Performance
5-1.Maximum Ratings
Rating
Value
Unit
AC Voltage Between Any Two Pins
Vpp
5
V
DC Voltage Between Any Two Pins
VDC
0
V
Storage temperature range
Tstg
-40 to +85
°C
Operable temperature range
TA
-25 to +85
°C
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
Issue : 1.1 C1
Date : March 2010
Tel : +44 118 979 1238
Fax : +44 118 979 1283
Email: [email protected]
5-2.Electronic Characteristics
Reference temperature:
TA = 25 °C
ZS = 50 Ω
Terminating source impedance:
Terminating load impedance:
ZL = 50 Ω
Group delay aperture:
0.25MHz
Characteristic
Centre Frequency
αrel≤3dB
Relative attenuation
Lower sidelobe
Upper sidelobe
Typical
Max.
Unit
480.00
481.00
MHz
--
22.5
24
dB
25.6
26.6
27.6
MHz
--40.0
38.0
3.0
3.2
46.0
43.0
4.6
4.6
---
dB
dB
dB
dB
40.0
46.0
--
dB
Δα
--
0.6
1.0
dB
--
227.5
--
ns
Δτ
--
8.5
15
ns
--
-86
--
ppm/K
fC
Insertion attenuation
480.00 MHz
(Reference level for the following data)
Pass bandwidth
Min.
479.00
α
B3dB
αrel
466.50 MHz
493.50 MHz
430.00 ….455.50 MHz
504.50 … 530.00 MHz
Reflected wave signal suppression
0.15μs … 2.0μs after main pulse
Amplitude ripple (p-p)
Group delay
Group delay ripple (p-p)
473.50 … 486.50 MHz
480.00 MHz
467.00 … 493.00 MHz
Temperature coefficient of frequency
τ
TCf
iCAUTION: Electrostatic Sensitive Device. Observe precautions for handling!
1.
2.
3.
4.
5.
6.
The frequency f C is defined as the midpoint between the 3dB frequencies.
Unless noted otherwise, all measurements are made with the filter installed in the specified test fixture that is
connected to a 50Ω test system with VSWR≤1.2:1. The test fixture L and C are adjusted for minimum insertion
loss at the filter centre frequency, f C. Note that insertion loss, bandwidth, and passband shape are dependent on
the impedance matching component values and quality.
Unless noted otherwise, specifications apply over the entire specified operating temperature range.
The specifications of this device are based on the test circuit shown above and subject to change or
obsolescence without notice.
All equipment designs utilizing this product must be approved by the appropriate government agency prior to
manufacture or sale.
Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications,
processes and circuits implemented within components or assemblies.
In keeping with our ongoing policy of product evolvement and improvement, the above specification is subject to change without notice.
ISO9001: 2000 Registered
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berks, RG41 2EY, UK
http://www.actcrystals.com
Issue : 1.1 C1
Date : March 2010
Similar pages