AZ7335 DPDT MINIATURE POWER RELAY FEATURES • • • • • • • • Dielectric strength 5000 Vrms Low cost Epoxy sealed version available 8 Amp switching — double pole contacts Isolation spacing greater than 8mm Class F insulation system available UL, CUR E44211 TUV R50290835 GENERAL DATA CONTACTS Arrangement DPST (2 Form A) DPDT (2 Form C) Ratings Resistive load: Max. switched power: 240 W or 2000 VA Max. switched current: 8 A Max. switched voltage: 30* VDC or 250 VAC *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Rated Load UL, CUR Normally Open Contacts (N.O.) 8 A at 250 VAC, Resistive,100k cycles 8 A at 30 VDC, Resistive 100k cycles Normally Closed Contacts (N.C.) 4 A at 250 VAC, Resistive, 100k cycles 4 A at 30 VDC, Resistive, 100k cycles TUV 5A NO / 3A NC @ 250VAC / 30VDC, 100k cycles, 85°C 10A NO / 5A NC @ 250VAC / 30VDC, 100k cycles, 85°C 16A NO / 8A NC @ 250VAC / 30VDC, 100k cycles, 85°C Material Silver tin oxide Resistance 100 milliohms max. (6 V, 1 A voltage drop method) COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation 353 mW(Standard), 300 mW(Sensitive) 1.2 W at 20°C (68°F) ambient (Standard) 0.9 W at 20°C (68°F) ambient (Sensitive) Temperature Rise Temperature 40°C (104°F) at nominal coil voltage Max. 105°C (221°F) Max. 155°C (311°F) Class F Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 5 A 250 VAC Res. Operate Time (max) 15 ms at nominal coil voltage (standard) 20 ms at nominal coil voltage (sensitive) Release Time (max) 8 ms at nominal coil voltage (with no coil suppression) Dielectric Strength 5000 VAC contact to coil (at sea level for 1 min.) 1000 VAC between open contacts 2500 VAC between contact sets 10,000 V surge contact to coil Insulation Resistance 1000 megohms min. at 500 VDC Dropout Greater than 10% of nominal coil voltage Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) Vibration 0.059" DA at 10–55 Hz Shock Mechanical Operational 100G 10 G Enclosure P.B.T. polyester Terminals Tinned copper alloy, P.C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 13 grams NOTES 1. All values at 23°C (73.4°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 3/13/2015 AZ7335 RELAY ORDERING DATA COIL SPECIFICATIONS (STANDARD) Nominal Coil VDC 3 Must Operate VDC 2.1 Max. Continuous VDC 3.9 5 6 9 12 18 24 48 3.5 4.2 6.3 8.4 12.6 16.8 33.6 6.5 7.8 11.7 15.6 23.4 31.2 62.4 ORDER NUMBER* Coil Resistance 13 ±10% Form A (DPST) AZ7335–2A–3DK Form C (DPDT) AZ7335–2C–3DK 36 48.5 115 200 450 820 3300 ±10% ±10% ±10% ±10% ±10% ±10% ±10% AZ7335–2A–5DK AZ7335–2A–6DK AZ7335–2A–9DK AZ7335–2A–12DK AZ7335–2A–18DK AZ7335–2A–24DK AZ7335–2A–48DK AZ7335–2C–5DK AZ7335–2C–6DK AZ7335–2C–9DK AZ7335–2C–12DK AZ7335–2C–18DK AZ7335–2C–24DK AZ7335–2C–48DK Coil Resistance 17 ±10% Form A (DPST) AZ7335–2A–3DSK Form C (DPDT) AZ7335–2C–3DSK 48.5 68 155 270 600 1100 4400 AZ7335–2A–5DSK AZ7335–2A–6DSK AZ7335–2A–9DSK AZ7335–2A–12DSK AZ7335–2A–18DSK AZ7335–2A–24DSK AZ7335–2A–48DSK AZ7335–2C–5DSK AZ7335–2C–6DSK AZ7335–2C–9DSK AZ7335–2C–12DSK AZ7335–2C–18DSK AZ7335–2C–24DSK AZ7335–2C–48DSK RELAY ORDERING DATA COIL SPECIFICATIONS (SENSITIVE) Nominal Coil VDC 3 Must Operate VDC 2.25 Max. Continuous VDC 3.9 5 6 9 12 18 24 48 3.75 4.50 6.75 9.00 13.50 18.00 36.00 6.5 7.8 11.7 15.6 23.4 31.2 62.4 ORDER NUMBER* ±10% ±10% ±10% ±10% ±10% ±10% ±10% *For epoxy seal add “E” after DK or DSK. For class F insulation system add suffix “F” to part number. HARDWARE ORDERING DATA DESCRIPTION ORDER NUMBER DESCRIPTION ORDER NUMBER Socket (5.0 mm) ST484–U1 Retainer ST482–2 3/13/2015 AZ7335 MECHANICAL DATA 0# "/!2$ ,!9/54 &ORM ! AND # 6IEWED TOWARD TERMINALS $)! $)! &ORM # ONLY (!2$7!2% PLACES &ORM ! PLACES &ORM # 34 5 -!8 $)! 7)2).' $)!'2!&ORM ! 2ETAINING #LIP &ORM # 6IEWED TOWARD TERMINALS $)! 6IEWED TOWARD TERMINALS 34 Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" unless specified. 3/13/2015