eSsmi-Conducto'i Lpioducti, fine. 20 STERN AVE. SPRINGFIELD, NEW JERSEY 07081 U.S.A. TELEPHONE: (973) 376-2922 (212)227-6005 FAX: (973) 376-8960 BC171.A.B BC172, A, B, C BC174,A,B TO-92 Plastic Package Amplifier Transistors ABSOLUTE MAXIMUM RATINGS (Ta=25°C unless specified otherwise) DESCRIPTION BC174 BC171 SYMBOL Collector Emitter Voltage Collector Base Voltage Emitter Base Voltage Collector Current Continuous Total Device Dissipation @ Ta=25°C Derate Above 25°C Total Device Dissipation @ Tc=25°C Derate Above 25°C Operating And Storage Junction Temperature Range THERMAL RESISTANCE Junction to ambient Junction to case 65 80 VCEO VCBO VEBO Ic PD PD TJ, Tstg Rfh(j-a) Rth(i-c) BC172 UNIT 25 30 V V V 45 50 6 100 350 2.8 1.0 8.0 mA mW mW/°C W mW/°C -55 to +150 °C 357 125 °C/W °C/W ELECTRICAL CHARACTERISTICS (Ta=25°C unless specified otherwise) DESCRIPTION SYMBOL TEST CONDITION MIN Collector Emitter Breakdown Voltage BVCEO BVEBO UNIT 65 45 25 V V V 6 V !E=100uA, lc=0 ALL Collector Cut off Current MAX lc=2mA,lB-0 BC174 BC171 BC172 Emitter Base Breakdown Voltage VALUE TYP 'CES BC174 BC171 BC172 VCE=70V, VBE = 0 VCE=50V, VBE = 0 VCE=35V, VBE = 0 15 15 15 nA nA nA VCE=30V, VBE = 0, Ta= 125°C 4 HA NJ Semi-Conductors reserves the right to change test conditions, parameters limits and package dimensions without notice information furnished by NJ Semi-Conductors is believed to be both accurate and reliable at the time of going to press. However NJ Semi-Conductors assumes no responsibility for any errors or omissions discovered in its use NJ Semi-Conductors encourages customers to verify that datasheets are current before placing orders. Quality Semi-Conductors SYMBOL TEST CONDITION DESCRIPTION MIN DC Current Gain HFE VALUE TYP UNIT MAX VCE=5V,lc=10nA 90 150 270 BC171A.2A, 4A BC171B, 2B,4B BC172C VCE=5V,lc=2mA BC174 BC171 BC172 120 120 120 450 800 800 BC171A, 2A, 4A BC171B, 2B.4B BC172C 120 180 380 220 460 800 VCE=5V,lc=100mA 120 180 300 BC171A, 2A, 4A BC171B, 2B, 4B BC172C Base Emitter Saturation Voltage VBE(SBO lc=10mA,lB-0.5mA Collector Emitter Saturation Voltage VcE(sat) lc=10mA,lB=0-5mA lc=100mA,lB=5mA Base Emitter on Voltage VBE (on) lc=2mA, VCE = 5V fT lc=10mA, VCE=5V f=100MHz 0.7 0.55 V 0.25 0.60 V V 0.70 V DYNAMIC CHARACTERISTICS Transition Frequency BC171 BC172 BC174 Output Capacitance C0b Input Capacitance cib IM Small Signal Current Gain BC171,2,4 BC171A, 2A, 4A, BC171B, 2B.4B BC172C NF Noise Figure BC171 BC172 BC174 150 150 150 E=0, VCB=10V f=1MHz c=Q, VEB=0.5V f=1MHz VCE=5V,lc=2mA =1KHZ V CE =5V,l c =0.2mA Rs=2KQ,f=1 KHZ. f=200Hz MHz 4.50 10 125 125 240 450 PF PF 900 260 500 900 10 10 10 dB — B I t < 1 73 All dimensions in mm unless specified otherwise SPECIFICATION ITEM 35 A A SEC AA DIM MAX. A 4.32 5.33 B 4.45 5.20 C 3.18 4,19 D 0.41 0.55 E 0.35 0.50 F PIN CONFIGURATION 1. EMITTER 2. BASE 3. COLLECTOR MIN. 5DEG G 1.14 1.40 H 1.14 1.53 K 12.70 L 1.982 All diminsions in mm. — 2.082 SYMBOL BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT FEED HOLE PITCH A1 A T p Po FEED HOLE CENTRE TO COMPONENT CENTRE P2 DISTANCE BETWEEN OUTER LEADS COMPONENT ALIGNMENT TAPE WIDTH HOLD -DOWN TAPE WIDTH HOLE POSITION MIN. MOM. MAX 40 48 39 F W Wo W1 HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCEF1 W2 Ho H1 L Do t F2 CLINCH HEIGHT PULL -OUT FORCE H2 (P) REMARKS 12.7 ±1 127 ±0.3 CUMULATIVE PITCH ERROR 1 0 mm/20 PITCH 635 ±0.4 TO BE MEASURED AT BOTTOM OF CLINCH 508 0 18 6 9 . .h TOL. 4.8 5,2 4.2 -456 -0.2 1 AT TOP OF BODY ±05 ±02 ••0.7 -05 0.5 16 ±02 ±0.5 23.25 11.0 4 ±0,2 12 2.54 (103-06 -•0.4 -0.1 3 6N NOTES 1 MAXIMUM ALIGNMENT DEVIATION BETWEEN LEADS NOT TO BE GREATER THAN 0.2 mm 2 MAXIMUM NON-CUMULATIVE VARIATION BETWEEN TAPE FEED HOLES SHALL NOT EXCEED 1 mm IN 20 PITCHES 3 HOLDDOWN TAPE NOT TO EXCEED BEYOND THE EDGE(S) OF CARRIER TAPE AND THERE SHALL BE NO EXPOSURE OF ADHESIVE. 4 NO MORE THAN 3 CONSECUTIVE MISSING COMPONENTS ARE PERMITTED 5. A TAPE TRAILER, HAVING AT LEAST THRfE FEED HOLES ARE REQUIRED AFTER THE LAST COMPONENT 6 SPLICES SHALL NOT INTERFERE WITH THE SPROCKET FEED HOLES.