ADS1672 AD S 167 2 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 625kSPS, 24-Bit Analog-to-Digital Converter FEATURES DESCRIPTION 1 • AC Performance: 107dB of Dynamic Range at 625kSPS 115.5dB of Dynamic Range at 78kSPS –115dB THD • DC Accuracy: 3ppm INL 2µV/°C Offset Drift 2ppm/°C Gain Drift • Programmable Digital Filter with User-Selectable Path: – Low-Latency: Completely settles in 5.5µs – Wide-Bandwidth: 305kHz BW with flat passband • Flexible Read-Only Serial Interface: – Standard CMOS – Serialized LVDS • Easy Conversion Control with START Pin • Out-of-Range Detection • Supply: Analog +5V, Digital +3V • Power: 350mW 2 APPLICATIONS Dual Filter Path AINP DS Modulator AINN Low-Latency Filter The ADS1672 ADC is comprised of a low-drift, chopper-stabilized modulator with out-of-range detection and a dual-path programmable digital filter. The dual filter path allows the user to select between two post-processing filters: low-latency or wide-bandwidth. The low-latency filter settles quickly in one cycle, for applications with large instantaneous changes, such as a multiplexer. The wide-bandwidth path provides an optimized frequency response for ac measurements with a passband ripple of less than 0.001dB, stop band attenuation of 115dB, and a bandwidth of 305kHz. The ADS1672 is controlled through I/O pins—there are no registers to program. A dedicated START pin allows for direct control of conversions: toggle the START pin to begin a conversion, and then retrieve the output data. The flexible serial interface supports data readback with either standard CMOS and LVDS logic levels, allowing the ADS1672 to directly connect to a wide range of microcontrollers, digital signal processors (DSPs), or field-programmable grid arrays (FPGAs). The ADS1672 operates from an analog supply of 5V and digital supply of 3V, and dissipates 350mW of power. When not in use, the PDWN pin can be used to power down all device circuitry. The device is fully specified over the industrial temperature range and is offered in a TQFP-64 package. DVDD AVDD VREFP Automated Test Equipment Vibration Analysis Sonar Test and Measurement VREFN • • • • The ADS1672 is a high-speed, high-precision analog-to-digital converter (ADC). Using an advanced delta-sigma (ΔΣ) architecture, it operates at speeds up to 625kSPS with outstanding ac performance and dc accuracy. CMOS and LVDS Compatible Serial Interface Wide-Bandwidth Filter Control Data Ready Data Output Serial Shift Clock Chip Select Interface Configuration Master Clock Filter Path Data Rate Start Conversion Power Down Out-of-Range DGND AGND ADS1672 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2008, Texas Instruments Incorporated ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION For the most current package and ordering information, see the Package Option Addendum at the end of this datasheet or see the TI website at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) Over operating free-air temperature range (unless otherwise noted). ADS1672 UNIT AVDD to AGND PARAMETER –0.3 to +6 V DVDD to DGND –0.3 to +3.3 V AGND to DGND –0.3 to +0.3 V 100 mA Input current Momentary 10 mA Analog I/O to AGND Continuous –0.3 to AVDD +0.3 V Digital I/O to DGND –0.3 to DVDD +0.3 V +150 °C Operating temperature range –40 to +85 °C Storage temperature range –60 to +150 °C Maximum junction temperature (1) 2 Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 ELECTRICAL CHARACTERISTICS All specifications are at TA = –40°C to +85°C, AVDD = 5V, DVDD = 3V, fCLK = 20MHz, VREF = +3V, and RBIAS = 7.5kΩ, unless otherwise noted. ADS1672 PARAMETER TEST CONDITIONS MIN TYP ANALOG INPUTS Full-scale input voltage Common-mode input voltage MAX UNIT . VIN = (AINP – AINN) ±VREF V VCM = (AINP + AINN)/2 2.5 V See Table 2 kSPS AC PERFORMANCE Data rate (fDATA) Dynamic range Signal-to-noise ratio (SNR) Inputs shorted together, wide-bandwidth path, fDATA = 625kSPS 105 107 Inputs shorted together, wide-bandwidth path, fDATA = 78.125kSPS 113 115.5 fIN = 10kHz, –0.5dBFS, wide-bandwidth path, fDATA = 625kSPS 102 fIN = 10kHz, –2dBFS, wide-bandwidth path, fDATA = 625kSPS 103 fIN = 10kHz, –6dBFS, wide-bandwidth path, fDATA = 625kSPS 99 fIN = 10kHz, –0.5dBFS –105 fIN = 10kHz, –2dBFS –109 fIN = 10kHz, –6dBFS –116 fIN = 10kHz, –0.5dBFS, signal harmonics excluded –120 Total harmonic distortion (THD) Spurious-free dynamic range (SFDR) dB dB dB dB DC PRECISION Resolution 24 Bits 24-bit (monotonic) Differential nonlinearity Integral nonlinearity Offset error TA = +25°C –2 Offset error drift 3 9.5 1 2 ppm of FSR Gain error TA = +25°C 1 Gain error drift 2 2 Noise mV µV/°C 2 % ppm/°C See Noise Performance table (Table 2) Common-mode rejection Power-supply rejection At dc 92 dB At dc, AVDD 92 dB DIGITAL FILTER CHARACTERISTICS (WIDE-BANDWIDTH PATH) Passband 0 Passband ripple Passband transition –0.1dB attenuation 0.432fDATA –3.0dB attentuation 0.488fDATA Stop band 0.424fDATA Hz ±0.0001 dB Hz Hz fCLK – 0.576fDATA 0.576fDATA Hz Stop band attenuation 115 dB Group delay 28 tDRDY Settling time See Wide Bandwidth Filter section DIGITAL FILTER CHARACTERISTICS (LOW-LATENCY PATH) Bandwidth –3dB attenuation See Low-Latency Filter section Settling time Complete settling 1 tDRDY VOLTAGE REFERENCE INPUTS Reference input voltage (VREF) VREF = (VREFP – VREFN) VREFP VREFN 2.75 3.0 3.25 V 2.75 3.0 3.25 V Short to AGND Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 V 3 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com ELECTRICAL CHARACTERISTICS (continued) All specifications are at TA = –40°C to +85°C, AVDD = 5V, DVDD = 3V, fCLK = 20MHz, VREF = +3V, and RBIAS = 7.5kΩ, unless otherwise noted. ADS1672 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 0.7DVDD DVDD V DGND 0.3DVDD V ±10 µA DIGITAL INPUTS VIH VIL Input leakage DGND < VIN < DVDD CMOS OUTPUTS VOH IOH = –50µA VOL IOL = 50µA 0.8DVDD V 0.2DVDD V LVDS OUTPUTS Steady-state differential output voltage magnitude 340 mV Change in steady-state differential output voltage magnitude between logic states ±50 mV Steady-state common-mode voltage output 1.2 V Δ|VOC(SS)| Change in steady-state common-mode output voltage between logic states ±50 mV VOC(pp) Peak-to-peak change in common-mode output voltage 50 VOY or VOZ = 0V 3 mA VOD = 0V 3 mA VO = 0V or +DVDD ±5 |VOD(SS)| Δ|VOD(SS)| VOC(SS) Short-circuit output current (IOS) High-impedance output current (IOZ) Load 150 mV µA 5 pF V POWER-SUPPLY REQUIREMENTS AVDD 4.75 5.0 5.25 DVDD 2.7 3.0 3.3 V 51 55 mA CMOS outputs, DVDD = 3V 28 32 mA LVDS outputs, DVDD = 3V 33 37 mA CMOS outputs, AVDD = 5V, DVDD = 3V 350 370 mW Power down 5 AVDD current DVDD current Power dissipation 4 Submit Documentation Feedback mW Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 DEVICE INFORMATION 53 52 DVDD 54 DGND 55 DGND 56 DVDD 57 AGND 58 AVDD 59 AGND 60 CLK 61 AVDD CAP1 62 AGND VREFN 63 CAP2 64 VREFN VREFP VREFP TQFP PACKAGE (TOP VIEW) 51 50 49 AVDD 1 48 DVDD AGND 2 47 DGND AGND 3 46 DRDY AINN 4 45 DRDY AINP 5 44 DOUT AGND 6 43 DOUT 42 SCLK AVDD 7 RBIAS 8 AGND 9 40 RSV3 AGND 10 39 OTRD 41 SCLK ADS1672 AVDD 11 38 CS AVDD 12 37 START 22 23 24 25 26 27 28 29 30 31 32 DGND DVDD PDWN SCLK _SEL LVDS DGND LL_CONFIG 21 DGND 20 DVDD 19 RSV1 18 DVDD 17 RSV2 33 FPATH DGND 34 DVDD DGND 16 DGND 35 DRATE[1] DGND 15 DGND 36 DRATE[0] DGND 14 DGND VCM 13 Table 1. TERMINAL FUNCTIONS PIN NAME NO. FUNCTION AVDD 1, 7, 11, 12, 53, 58 DESCRIPTION Analog Analog supply AGND 2, 3, 6, 9, 10, 54, 56, 57 Analog Analog ground AINN 4 Analog Input Negative analog input AINP 5 Analog Input Positive analog input RBIAS 8 Analog Analog bias setting resistor VCM 13 Analog Terminal for external bypass capacitor connection to internal common-mode voltage DGND 14, 15, 16, 17, 18, 19, 20, 25, 26, 31, 47, 50, 51 Digital Digital ground RSV2 21 Reserved Short to digital ground RSV1 22 Reserved Short to digital ground DVDD 23, 24, 27, 34, 48, 49, 52 Digital PDWN 28 Digital Input Power-down control, active low SCLK_SEL 29 Digital Input Shift-clock source select. If SCLK_SEL = '0', then SCLK is internally generated. If SCLK_SEL = '1', then SCLK must be externally generated. LVDS 30 Digital Input Serial interface select. If LVDS = '0', then interface is LVDS-compatible. If LVDS = '1', then interface is CMOS-compatible. Digital supply Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 5 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com Table 1. TERMINAL FUNCTIONS (continued) PIN NAME NO. FUNCTION DESCRIPTION LL_CONFIG 32 Digital Input Configure low-latency digital filter. If LL_CONFIG = '0', then single-cycle settling is selected. If LL_CONFIG = '1', then fast-response is selected. FPATH 33 Digital Input Digital filter path selection. If FPATH = '0', then path is wide-bandwidth. If FPATH = '1', then path is low-latency. DRATE[1:0] 35, 36 Digital Input Data rate selection START 37 Digital Input Start convert, reset, and synchronization control input CS 38 Digital Input Chip select; active low. OTRD 39 Digital Output RSV3 40 Reserved SCLK 41 Digital Output SCLK 42 DOUT 43 Digital Output Negative LVDS serial data output DOUT 44 Digital Output Positive LVDS serial data output DRDY 45 Digital Output Negative data ready output DRDY 46 Digital Output Positive data ready output CLK 55 Digital Input CAP1 59 Analog Terminal for 1µF external bypass capacitor 60, 61 Analog Negative reference voltage. Short to analog ground. 62 Analog Terminal for 1µF external bypass capacitor 63, 64 Analog Positive reference voltage VREFN CAP2 VREFP 6 Digital filter out-of-range indicator This pin must be left floating. Do not connect or short to ground. Negative shift clock output. If SCLK_SEL = '0', then SCLK is the complementary shift clock output. If SCLK_SEL = '1', then SCLK always output is 3-state. Positive shift clock output. Digital Input/Output If SCLK_SEL = '0', then SCLK is an output. If SCLK_SEL = '1', then SCLK is an input. Master clock input Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 TIMING CHARACTERISTICS tCLK CLK tCLKDR tDRPW DRDY tSCLK tDRSCLK SCLKinternal tDOPD tDOHD MSB DOUT LSB Figure 1. Data Retrieval Timing with Internal SCLK (SCLK_SEL = 0) TIMING REQUIREMENTS: Internal SCLK At TA = –40°C to +85°C, and DVDD = 2.7V to 3.3V. SYMBOL DESCRIPTION MIN TYP MAX 50 UNIT tCLK CLK period (1/fCLK) tCLKDR CLK to DRDY delay 36 ns ns tDRPW DRDY pulse width 1 tCLK tDRSCLK DRDY active edge to internally-generated SCLK rising edge 4 ns tSCLK SCLK period (1/fSCLK) 1 tDOPD Rising edge of SCLK to new valid data output (propagation delay) tDOHD Rising edge of SCLK to previous valid data output (hold time) tCLK 3 3 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ns ns 7 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com tCLK CLK tCLKDR tSCLKDR DRDY tDRPW CS (1) tCSSC tSPW tSPW SCLKexternal tSCLK tDOPD DOUT Hi-Z tDOHD MSB tCSRDO LSB tCSFDO (1) CS may be tied low. Figure 2. Data Retrieval Timing with External SCLK (SCLK_SEL = 1) TIMING REQUIREMENTS: External SCLK At TA = –40°C to +85°C, and DVDD = 2.7V to 3.3V. SYMBOL DESCRIPTION MIN TYP MAX 50 UNIT tCLK CLK period (1/fCLK) tCLKDR CLK to DRDY delay 37 ns ns tDRPW DRDY pulse width 1 tCLK tCSSC CS active low to first Shift Clock (setup time) 5 ns tSCLK SCLK period (1/fSCLK) 25 ns tSPW SCLK high or low pulse width 12 tDOPD Rising edge of SCLK to new valid data output (propagation delay) tDOHD Rising edge of SCLK to previous valid data output (hold time) 11 ns tSCLKDR Setup time of DRDY rising after SCLK falling edge 3 tCLK tCST CS rising edge to DOUT 3-state 5 ns tCDSO CS inactive to data output 3-state 8 ns ns 11 ns tSTART_CLKR CLK tSETTLE START tSTART DRDY Figure 3. START Timing TIMING REQUIREMENTS: START At TA = –40°C to +85°C, and DVDD = 2.7V to 3.3V. SYMBOL DESCRIPTION tSTART_CLKR Setup time, rising edge of START to rising edge of CLK tSTART Start pulse width 8 Submit Documentation Feedback MIN TYP MAX UNIT 0.5 tCLK 2 tCLK Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 TYPICAL CHARACTERISTICS All specifications are at TA = –40°C to +85°C, AVDD = 5V, DVDD = 3V, fCLK = 20MHz, VREF = +3V, and RBIAS = 7.5kΩ, unless otherwise noted. OUTPUT SPECTRUM (1k, –0.5dBFS SIGNAL) OUTPUT SPECTRUM DETAIL VIEW (1k, –0.5dBFS SIGNAL) 0 0 fIN = 1kHz, -0.5dBFS THD = -109.1dBc 65,536 points -40 -60 -80 -100 fIN = 1kHz, -0.5dBFS THD = -109.1dBc 65,536 points -20 Amplitude (dBFS) Amplitude (dBFS) -20 -40 -60 -80 -100 -120 -120 -140 -140 -160 -160 0 50 100 150 200 250 0 300 325 1 2 3 6 7 8 Figure 5. OUTPUT SPECTRUM (1k, –6dBFS SIGNAL) OUTPUT SPECTRUM DETAIL VIEW (1k, –6dBFS SIGNAL) 9 10 0 fIN = 1kHz, -6dBFS THD = -119.9dBc 65,536 points -20 -40 -60 -80 -100 fIN = 1kHz, -6dBFS THD = -119.9dBc 65,536 points -20 Amplitude (dBFS) Amplitude (dBFS) 5 Figure 4. 0 -40 -60 -80 -100 -120 -120 -140 -140 -160 -160 0 50 100 150 200 250 0 300 325 1 2 3 4 5 6 7 8 9 10 Frequency (kHz) Frequency (kHz) Figure 6. Figure 7. OUTPUT SPECTRUM (10k, –0.5dBFS SIGNAL) OUTPUT SPECTRUM (10k, –6dBFS SIGNAL) 0 0 fIN = 10kHz, -0.5dBFS THD = -108.9dBc 65,536 points -20 -40 -60 -80 -100 fIN = 10kHz, -6dBFS THD = -118.0dBc 65,536 points -20 Amplitude (dBFS) Amplitude (dBFS) 4 Frequency (kHz) Frequency (kHz) -40 -60 -80 -100 -120 -120 -140 -140 -160 -160 0 50 100 150 200 250 300 325 0 50 100 150 200 Frequency (kHz) Frequency (kHz) Figure 8. Figure 9. 250 300 325 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 9 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com TYPICAL CHARACTERISTICS (continued) All specifications are at TA = –40°C to +85°C, AVDD = 5V, DVDD = 3V, fCLK = 20MHz, VREF = +3V, and RBIAS = 7.5kΩ, unless otherwise noted. OUTPUT SPECTRUM (10k, –60dBFS SIGNAL) SNR and |THD| vs INPUT FREQUENCY 0 120 Amplitude (dBFS) -20 -40 -60 -80 -100 |THD|, AIN = -6dBFS 115 SNR, |THD| (dBc) fIN = 10kHz, -60dBFS SNR = 45.6dBc THD = -71.6dBc 65,536 points -120 110 |THD|, AIN = -0.5dBFS 105 SNR, AIN = -0.5dBFS 100 -140 SNR, AIN = -6dBFS -160 95 0 50 100 150 200 250 300 325 10 Figure 10. Figure 11. SNR and |THD| vs SAMPLING FREQUENCY SNR and |THD| vs INPUT AMPLITUDE fIN = 10kHz |THD|, AIN = -6dBFS SNR, |THD| (dBc) SNR, |THD| (dBc) fIN = 10kHz 120 120 115 110 |THS|, AIN = -0.5dBFS 105 100 |THD| 80 SNR 60 40 100 SNR, AIN = -0.5dBFS SNR, AIN = -6dBFS 95 0 5 20 10 15 20 25 -80 -70 -60 -30 Figure 13. SNR and |THD| vs INPUT COMMON-MODE SNR and |THD| vs TEMPERATURE -20 -10 0 120 fIN = 10kHz fIN = 10kHz |THD|, AIN = -6dBFS |THD|, AIN = -6dBFS 115 110 SNR, |THD| (dBc) SNR, |THD| (dBc) -40 Figure 12. |THS|, AIN = -0.5dBFS 105 SNR, AIN = -0.5dBFS 100 110 |THS|, AIN = -0.5dBFS 105 SNR, AIN = -0.5dBFS 100 SNR, AIN = -6dBFS SNR, AIN = -6dBFS 95 95 1.6 10 -50 Input Signal Amplitude (dBFS) Sampling Frequency (MHz) 115 1000 Frequency (kHz) 140 125 100 Frequency (kHz) 1.8 2.0 2.2 2.4 2.6 2.8 3.0 -40 -15 10 35 Input Common-Mode (V) Temperature (°C) Figure 14. Figure 15. Submit Documentation Feedback 60 85 Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 TYPICAL CHARACTERISTICS (continued) All specifications are at TA = –40°C to +85°C, AVDD = 5V, DVDD = 3V, fCLK = 20MHz, VREF = +3V, and RBIAS = 7.5kΩ, unless otherwise noted. NOISE HISTOGRAM (OSR = 32) Wide Bandwidth, fDATA = 625kSPS s = 27 Output Codes 65k Points Input-Shorted Number of Occurrences 2000 1500 1000 500 5000 Wide Bandwidth fDATA = 78.125kSPS s = 10.8 Output Codes 65k Points 4500 Number of Occurrences 2500 NOISE HISTOGRAM (OSR = 256) 4000 3500 3000 2500 2000 1500 1000 500 0 -126 -112 -98 -84 -70 -56 -42 -28 -14 0 14 28 42 56 70 84 98 112 126 -48 -44 -40 -36 -32 -28 -24 -20 -16 -12 -8 -4 0 4 8 12 16 20 24 28 32 36 40 44 48 0 24-Bit Output Code 24-Bit Output Code Figure 16. Figure 17. DYNAMIC RANGE vs OVERSAMPLING RATIO NOISE vs INPUT VOLTAGE 14 78.125kHz: DRATE = 00 156.25kHz: DRATE = 01 312.5kHz: DRATE = 10 625kHz: DRATE = 11 114 FPATH = 0 DRATE = 11 12 RMS Noise (mV) Dynamic Range (dBFS) 116 112 110 LL 10 8 FPATH = 1 DRATE = 11 FPATH = 1 DRATE = 00 6 4 108 106 78,125 FPATH = 0 DRATE = 00 2 WB 0 156,250 312,500 625,000 -95 -76 Data Rate (Hz) -38 -19 0 19 38 57 76 95 Analog Input Range (±100% of FSR) Figure 18. Figure 19. INL vs TEMPERATURE |THD| vs RBIAS 5 115 fCLK = 10MHz 4 fCLK = 2.5MHz 3 +85°C 2 -40°C 1 |THD| (dBc) Integral Nonlinearity (ppm) -57 0 +25°C -1 110 105 -2 fCLK = 20MHz -3 -4 -5 fIN = 10kHz, AIN = -0.5dBFS 100 -3 -2 -1 0 1 2 3 5 10 15 20 25 30 35 40 Analog Input Voltage (V) RBIAS (kW) Figure 20. Figure 21. 45 50 55 60 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 65 11 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com TYPICAL CHARACTERISTICS (continued) All specifications are at TA = –40°C to +85°C, AVDD = 5V, DVDD = 3V, fCLK = 20MHz, VREF = +3V, and RBIAS = 7.5kΩ, unless otherwise noted. POWER vs RBIAS 500 fIN = 10kHz, AIN = -0.5dBFS 450 Power (mW) 400 350 300 fCLK = 20MHz 250 200 fCLK = 2.5MHz fCLK = 10MHz 150 100 50 5 10 15 20 25 30 35 40 45 50 55 60 65 RBIAS (kW) Figure 22. 12 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 OVERVIEW The ADS1672 is a 24-bit, ΔΣ analog-to-digital converter (ADC). It provides high-resolution measurements of both ac and dc signals and features an advanced multi-stage analog modulator with a programmable and flexible digital decimation filter. A dedicated START pin allows precise conversion control; toggle the pin to begin the conversion process. The ADS1672 is configured by setting the appropriate I/O pins—there are no registers to program. Data are retrieved over a serial interface that can support either CMOS or LVDS voltage levels. In addition, the serial interface can be internally or externally clocked. This flexibility allows direct connection to a wide range of digital hosts including DSPs, FPGAs, and microcontrollers. A detection circuit monitors the conversions to indicate when the inputs are out-of-range for an extended duration. A power-down pin (PDWN) shuts off all circuitry when the ADS1672 is not in use. x x DVDD x AVDD VREFN VREFP CAP2 CAP1 RBIAS Figure 23 shows a block diagram of the ADS1672. The modulator is chopper-stabilized for low-drift performance and measures the differential input signal VIN = (AINP – AINN) against the differential reference VREF = (VREFP – VREFN). The digital filter receives the modulator signal and processes it through the user-selected path. The low-latency path provides single-cycle settling, and is ideal when using a multiplexer or when measuring large transients. The wide-bandwidth path provides outstanding frequency response with very low passband ripple, a steep transition band, and large stop band attenuation. This path is well-suited for applications that require high-resolution measurements of high-frequency ac signal content. ADS1672 VCM Biasing START S Dual Filter Path VREF AINP AINN S VIN PDWN Low-Latency Filter DS Modulator Wide-Bandwidth Filter CLK CMOS- and LVDSCompatible Serial Interface and Control DRDY, DRDY DOUT, DOUT SCLK, SCLK CS LVDS SCLK_SEL FPATH DGND AGND OTRD Figure 23. ADS1672 Block Diagram Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 13 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com NOISE PERFORMANCE ANALOG INPUTS (AINP, AINN) The ADS1672 offers outstanding noise performance that can be optimized by adjusting the data rate. As the averaging is increased (thus reducing the data rate), the noise drops correspondingly. Table 2 shows the noise as a function of data rate for both the low-latency and the wide-bandwidth filter paths under the conditions shown. The ADS1672 measures the differential signal, VIN = (AINP – AINN), against the differential reference, VREF = (VREFP – VREFN). The most positive measurable differential input is VREF, which produces the most positive digital output code of 7FFFFFh. Likewise, the most negative measurable differential input is –VREF, which produces the most negative digital output code of 800000h. Table 2 lists some of the more common methods of specifying noise. The dynamic range is the ratio of the root-mean-square (RMS) value of a full-scale sine wave to the RMS noise with the inputs shorted together. This value is expressed in decibels relative to full-scale (dBFS). The input-referred noise is the RMS value of the noise with the inputs shorted, referred to the input of the ADS1672. The effective number of bits (ENOB) is calculated from a dc perspective using the formula in Equation 1, where full-scale range equals 2VREF. ln Analog inputs must be driven with a differential signal to achieve optimum performance. The recommended common-mode voltage is 2.5V. The ADS1672 samples the analog inputs at very high speeds. It is critical that a suitable driver be used. See the Application Information section for recommended circuit designs. Full-scale range RMS noise ENOB = ln(2) (1) Noise-free bits specifies noise, again from a dc perspective using Equation 1, with peak-to-peak noise substituted for RMS noise. Table 2. Noise Performance (1) FILTER PATH DATA RATE[1:0] DATA RATE DYNAMIC RANGE INPUT-REFERRED NOISE ENOB NOISE-FREE BITS 00 36kSPS 115dB 3.9µVRMS 20.6 17.8 01 68kSPS 113dB 5.0µVRMS 20.2 17.5 10 120kSPS 110dB 6.7µVRMS 19.8 17.1 11 180kSPS 108dB 8.9µVRMS 19.4 16.7 00 78.1kSPS 115.5dB 3.9µVRMS 20.6 17.8 01 156.3kSPS 113dB 5.0µVRMS 20.2 17.5 10 312.5kSPS 110dB 6.8µVRMS 19.8 17.0 11 625.0kSPS 107dB 10.1µVRMS 19.2 16.5 Low-Latency (single-cycle settling configuration) Wide-Bandwidth (1) 14 VREF = 3V, fCLK = 20MHz. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 VOLTAGE REFERENCE INPUTS (VREFN, VREFP) CONVERSION START The voltage reference for the ADS1672 is the differential voltage between VREFP and VREFN: VREF = (VREFP – VREFN) A high-quality reference voltage with the appropriate drive strength is essential for achieving the best performance from the ADS1672. Noise and drift on the reference degrade overall system performance. See the Application Information section for reference circuit examples. It is recommended that a minimum 10µF and 0.1µF ceramic bypass capacitors be used directly across the reference inputs, VREFP and VREFN. These capacitors should be placed as close as possible to the device under test for optimal performance. COMMON-MODE VOLTAGE (VCM) The START pin provides an easy and precise conversion control. To perform a single conversion, pulse the START pin as shown in Figure 24. The START signal is latched internally on the rising edge of CLK. Multiple conversions are performed by continuing to hold START high after the first conversion completes; see the digital filter descriptions for more details on multiple conversions, because the timing depends on the filter path selected. A conversion can be interrupted by issuing another START pulse before the ongoing conversion completes. When an interruption occurs, the data for the ongoing conversion are flushed and a new conversion begins. DRDY indicates that data are ready for retrieval after the filter has settled, as shown in Figure 25. The VCM pin outputs a voltage of AVDD/2 and can be used to set the common-mode output of the circuitry that drives the ADS1672. The pin must be bypassed with a 1µF capacitor placed close to the package pin, even if it is not connected elsewhere. The VCM pin has limited drive ability and therefore must be buffered if connected to a load. tSTART_CLKR CLK tSETTLE (1) (1) tSETTLE START tSTART DRDY Figure 24. START Pin Used for Single Conversions Ongoing conversion flushed; new conversion started tSTART_CLKR CLK tSETTLE (1) START tSTART DRDY (1) See Low-Latency Filter section and Wide Bandwidth Filter section for specific values of settling time tSETTLE. Figure 25. Example of Restarting a Conversion with START Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 15 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com DIGITAL FILTER LOW-LATENCY DIGITAL FILTER In delta-sigma ADCs, the digital filter has a critical influence on device performance. The digital filter sets the frequency response, data rate, bandwidth, and settling time. Choosing to optimize some of these features in a filter means that compromises must be made with other specifications. These tradeoffs determine the applications for which the device is best suited. The low-latency (LL) filter provides a fast settling response targeted for applications that need high-precision measurements with minimal latency. A good example of this type of application is using a multiplexer to measure multiple inputs. The faster that the ADC settles, the faster the measurement can complete and the multiplexer can advance to the next input. The ADS1672 offers two digital filters on-chip, and allows the user to direct the output data from the modulator to either the Wide-Bandwidth or Low-Latency filter. These filters allow the user to use one converter design to address multiple applications. The Low-Latency path filter has minimal latency or settling time. This path is ideal for measurements with large, quick changes on the inputs (for example, when using a multiplexer). The low-latency characteristic allows the user to cycle through the multiplexer at high speeds. The frequency characteristics are relaxed in order to provide the low latency. The ADS1672 LL filter supports two configurations to help optimize performance for these types of applications. The other path provides a filter with excellent frequency response characteristics. The passband ripple is extremely small, the transition band is very steep, and there is large stop band attenuation. These characteristics are needed for high-resolution measurements of ac signals. The tradeoff here is that settling time increases; but for signal processing, this increase is not generally a critical concern. The FPATH digital input pin sets the filter path selection, as shown in Table 3. Note that the START pin must be strobed after a change to the filter path selection or data rate. If a conversion is in process during a filter path or data rate change, the output data are not valid and should be discarded. The LL_CONFIG input pin selects the configuration, as shown in Table 4. Be sure to strobe the START pin after changing the configuration. If a conversion is in process during a configuration change, the output data for that conversion are not valid and should be discarded. Table 4. Low-Latency Pin Configurations LL_CONFIG PIN LOW-LATENCY CONFIGURATION 0 Single-cycle settling 1 Fast response The first configuration is single-cycle settling. As the name implies, this configuration allows for the filter to completely settle in one conversion cycle; there is no need to discard data. Each data output is comprised of information taken during only the previous conversion. The DRATE[1:0] digital input pins select the data rate for the Single-Cycle Settling configuration, as shown in Table 5. Note that the START pin must be strobed after a change to the data rate. If a conversion is in process during a data rate change, the output data for that conversion are not valid and should be discarded. Table 3. ADS1672 Filter Path Selection blank FPATH PIN SELECTED FILTER PATH 1 Low-latency path 0 Wide-bandwidth path blank Table 5. Low-Latency Data Rates with Single-Cycle Settling Configuration (1) 16 –3dB BANDWIDTH (1) DRATE[1:0] DATA RATE (1/tDRDY-SCS) SETTLING TIME, tSETTLE-LL 00 36.30kSPS 27.55µs 550 tCLK 01 67.80kSPS 14.75µs 294 tCLK 68kHZ 10 119.76kSPS 8.35µs 166 tCLK 130kHZ 11 180.15kSPS 5.55µs 110 tCLK 215kHz 34kHz The input signal aliases when its frequency exceeds fDATA/2, in accordance with the Nyquist theorem. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 The second configuration is fast response. The DRATE[1:0] digital input pins select the data rate for the Fast Response Configuration, as shown in Table 6. When selected, this configuration provides a higher output data rate. The faster output data rate allows for more averaging by a post-processor within a given time interval to reduce noise. It also provides a faster indication of changes on the inputs when monitoring quickly-changing signals (for example, in a control loop application). Figure 26 illustrates the response of both configurations on approximately the same time scale in order to highlight the differences. With the single-cycle settling configuration, each conversion fully settles; in other words, the conversion period tDRDY-SCS = tSETTLE-LL. The benefit of this configuration is its simplicity—the ADS1672 functions similar to a SAR converter and there is no need to consider discarding partially-settled data because each conversion is fully settled. Table 6. Low-Latency Data Rates with Fast-Response Configuration With the fast response configuration, the data rate for conversions after initial settling is faster; that is, the conversion time is less than the settling: tDRDY-FR < tSETTLE-LL. One benefit of this configuration is a faster response to changes on the inputs, because data are supplied at a faster rate. Another advantage is better support for post-processing. For example, if multiple readings are averaged to reduce noise, the higher data rate of the fast response configuration allows this averaging to happen in less time than it requires with the single-cycle settling filter. A third benefit is the ability to measure higher input frequencies without aliasing as a result of the higher data rate. DRATE [1:0] DATA RATE (1/tDRDY-FR) SETTLING TIME, tSETTLE-LL –3dB BANDWIDTH 00 78.125kSPS 27.55µs 550 tCLK 34kHz 01 156.25kSPS 14.75µs 294 tCLK 68kHZ 10 312.5kSPS 8.35µs 166 tCLK 130kHZ 11 625kSPS 5.55µs 110 tCLK 215kHz Settling Time The settling time in absolute time (µs) is the same for both configurations of the low-latency filter, as shown in Table 5 and Table 6. The difference between the configurations is seen with the timing of the conversions after the filter has settled from a pulse on the START pin. tSTART_CLKR CLK tSETTLE START tSTART DRDYSCS tDRDY-SCS = tSETTLE-LL tSETTLE-LL tDRDY-FR DRDYFR NOTE: DRDYSCS is the DRDY output with the low-latency single-cycle settling configuration. DRDYFR is the DRDY output with the low-latency fast-response settling configuration. Figure 26. Low-Latency Single-Cycle Settling and Fast-Response Configuration Conversion Timing Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 17 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com It is important to note, however, that the absolute settling time of the low-latency path does not change when using the fast response configuration. Changes on the input signal during conversions after the initial settling require multiple cycles to fully settle. To help illustrate this requirement, consider a change on the inputs as shown in Figure 30, where START is assumed to have been taken high before the input voltage was changed. 0 DRATE[1:0]=‘00’ -10 Magnitude (dB) -20 DRATE[1:0]=‘11’ -30 -40 -50 -60 The readings after the input change settle as shown in Figure 27. Conversion 3 provides a fully-settled result at the new VIN signal. -70 -80 0 120 0.2 0.3 0.4 0.5 0.6 0.7 Frequency (fIN/fDATA) 0.8 0.9 1.0 Figure 28. Frequency Response of Low-Latency Filter in Fast-Response Configuration 100 Settling (%) 0.1 80 60 0 40 -20 Magnitude (dB) 20 0 0 1 3 2 4 Conversions (1/fDRDY-FR) -40 -60 -80 -100 Figure 27. Step Response for Low-Latency Filter with Fast-Response Configuration -120 -140 0 Frequency Response Figure 28 shows the frequency response for the low-latency filter path normalized to the output data rate, fDATA. The overall frequency response repeats at the modulator sampling rate, which is the same as the input clock frequency. Figure 29 shows the response with the fastest data rate selected (625kSPS when fCLK = 20MHz). 1 2 Frequency (fIN/fCLK) 3 Figure 29. Extended Frequency Response of Low-Latency Path Change on Analog Inputs VIN Fully-Settled Data Available Data 0 Data 1 Data 2 Data 3 Data 4 DRDYLL-FR NOTE: START pin held high previous to change on analog inputs. Figure 30. Settling Example with the Low-Latency Filter in Fast-Response Configuration 18 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 Phase Response 20 0 -20 Magnitude (dB) The low-latency filter uses a multiple stage linear phase digital filter. Linear phase filters exhibit constant delay time versus input frequency (also know as constant group delay). This feature of linear phase filters means that the time delay from any instant of the input signal to the corresponding same instant of the output data is constant and independent of the input signal frequency. This behavior results in essentially zero phase error when measuring multi-tone signals. -40 -60 -80 -100 -120 -140 WIDE-BANDWIDTH FILTER 0 The wide-bandwidth (WB) filter is well-suited for measuring high-frequency ac signals. This digital filter offers excellent passband and stop band characteristics. Table 7. Wide-Bandwidth Data Rates DRATE [1:0] DATA RATE (1/tDRDY-WB) –3dB BANDWIDTH SETTLING TIME, tSETTLE-WB 00 78.125kSPS 38kHz 704µs 14061 tCLK 01 156.25kSPS 76kHz 352µs 7033 tCLK 10 312.50kSPS 152kHz 176µs 3519 tCLK 11 625.0kSPS 305kHz 88µs 1762 tCLK 0.2 0.3 0.4 0.5 0.6 0.7 Frequency (fIN/fDATA) 0.8 0.9 1.0 Figure 31. Frequency Response of Wide-Bandwidth Filter blank 0.00005 -0.00005 Magnitude (dB) The DRATE[1:0] digital input pins select from the four data rates available with the WB filter, as shown in Table 7. Note that the START pin must be strobed after a change to the data rate. If a conversion is in process during a data rate change, the output data for that conversion are not valid and should be discarded. 0.1 -0.00015 -0.00025 -0.00035 0 0.1 0.2 0.3 0.4 0.5 Normalized Frequency (fIN/fDATA) Figure 32. Passband Response for Wide-Bandwidth Filter Frequency Response 2 0 Magnitude (dB) Figure 31 shows the frequency response for the wide-bandwidth filter path normalized to the output data rate, fDATA. Figure 32 shows the passband ripple, and the transition from passband to stop band is illustrated in Figure 33. These three plots are valid for all of the data rates available on the ADS1672. Simply substitute the selected data rate to express the x-axis in absolute frequency. -2 -4 -6 -8 -10 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 Normalized Frequency (fIN/fDATA) Figure 33. Transition Band Response for Wide-Bandwidth Filter Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 19 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com Settling Time The overall frequency response repeats at the modulator sampling rate, which is the same as the input clock frequency. Figure 34 shows the response with the fastest data rate selected (625kSPS when fCLK = 20MHz). The Wide-Bandwidth filter fully settles before indicating data are ready for retrieval after the START pin is taken high, as shown in Figure 36. For this filter, the settling time is larger than the conversion time: tSETTLE-WB > tDRDY-WB. Instantaneous steps on the input require multiple conversions to settle if START is not pulsed. Figure 35 shows the settling response with the x-axis normalized to conversions or data-ready cycles. The output is fully settled after 55 data-ready cycles. Magnitude (dB) 0 -50 120 -100 100 Fully settled at 55 conversions Settling (%) 80 -150 0 1 2 Frequency (fIN/fCLK) 3 60 40 20 Figure 34. Extended Frequency Response of Wide-Bandwidth Path 0 -20 0 Phase Response 10 20 30 40 50 60 Conversions (1/tDRDY-WB) The wide-bandwidth filter uses a multiple-stage, linear-phase digital filter. Linear phase filters exhibit constant delay time versus input frequency (also know as constant group delay). This feature means that the time delay from any instant of the input signal to the corresponding same instant of the output data is constant and independent of the input signal frequency. This behavior results in essentially zero phase error when measuring multi-tone signals. Figure 35. Step Response for Wide-Bandwidth Filter tSTART_CLKR CLK tSETTLE START tDRDY (1) tDRDY tDRDY tDRDY DRDY (1) tDRDY = 1/fDATA. See Table 7 for the relationship between tSETTLE and tDRDY when using the Wide-Bandwidth filter. Figure 36. START Pin Used for Multiple Conversions with Wide-Bandwidth Filter Path 20 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 OTRD FUNCTION The ADS1672 provides an out-of-range (OTRD) pin that can be used in feedback loops to set the dynamic range of the input signal. The OTRD function is triggered when the output code of the digital filter exceeds the positive or negative full-scale range. OTRD goes high on the rising edge of DRDY. When the digital output code returns within the full-scale range, OTRD returns low on the next rising edge of DRDY. OTRD can also be used when small out-of-range input glitches must be ignored. SERIAL INTERFACE The ADS1672 offers a flexible and easy-to-use, read-only serial interface designed to connect to a wide range of digital processors, including DSPs, microcontrollers, and FPGAs. The ADS1672 serial interface can be configured to support either standard CMOS voltage swings or low-voltage differential swings (LVDS). In addition, when using standard CMOS voltage swings, SCLK can be internally or externally generated. The ADS1672 is entirely controlled by pins; there are no registers to program. Connect the I/O pins to the appropriate level to set the desired function. Whenever changing the I/O pins that are used to control the ADS1672, be sure to issue a START pulse immediately after the change in order to latch the new values. USING LVDS OUTPUT SWINGS When the LVDS pin is set to '0', the ADS1672 outputs are LVDS TIA/EIA-644A compliant. The data out, shift clock, and data ready signals are output on the differential pairs of pins DOUT/DOUT, SCLK/SCLK, and DRDY/DRDY, respectively. The voltage on the outputs is centered on 1.2V and swings approximately 350mV differentially. For more information on the LVDS interface, refer to the document Low-Voltage Differential Signaling (LVDS) Design Notes (literature number SLLA014) available for download at www.ti.com. When using LVDS, the CS function is not available and SCLK must be internally generated. The states of the CS and SCLK_SEL pins are ignored, but do not leave these pins floating; they must be tied high or low. USING CMOS OUTPUT SWINGS When the LVDS pin is set to '1', the ADS1672 outputs are CMOS-compliant and swing from rail to rail. The data out and data ready signals are output on the differential pairs of pins DOUT/DOUT and DRDY/DRDY, respectively. Note that these are the same pins used to output LVDS signals when the LVDS pin is set to '0'. DOUT and DRDY are complementary outputs provided for convenience. When not in use, these pins should be left floating. See the Serial Shift Clock section for a description of the SCLK and SCLK pins. DATA OUTPUT (DOUT, DOUT) Data are output serially from the ADS1672, MSB first, on the DOUT and DOUT pins. When LVDS signal swings are used, these two pins act as a differential pair to produce the LVDS-compatible differential output signal. When CMOS signal swings are used, the DOUT pin is the complement of DOUT. If DOUT is not used, it should be left floating. DATA READY (DRDY, DRDY) Data ready for retrieval are indicated on the DRDY and DRDY pins. When LVDS signal swings are used, these two pins act as a differential pair to produce the LVDS-compatible differential output signal. When CMOS signal swings are used, the DRDY pin is the complement of DRDY. If one of the data ready pins is not used when CMOS swings are selected, it should be left floating. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 21 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com SERIAL SHIFT CLOCK (SCLK, SCLK, SCLK_SEL) The serial shift clock SCLK is used to shift out the conversion data, MSB first, onto the Data Output pins. Either an internally- or externally-generated shift clock can be selected using the SCLK_SEL pin. If SCLK_SEL is set to '0', a free-running shift clock is generated internally from the master clock and outputs on the SCLK and SCLK pins. The LVDS pin determines if the output voltages are CMOS or LVDS. If SCLK_SEL is set to '1' and LVDS is set to '1', the SCLK pin is configured as an input to accept an externally-generated shift clock. In this case, the SCLK pin always outputs low. When SCLK_SEL is set to '0', the SCLK and SCLK pins are configured as outputs, and the shift clock is generated internally using the master clock input (CLK). DATA FORMAT The ADS1672 outputs 24 bits of data in two’s complement format. A positive full-scale input produces an output code of 7FFFFFh, and the negative full-scale input produces an output code of 800000h. The output clips at these codes for signals exceeding full-scale. Table 9 summarizes the ideal output codes for different input signals. When the input is positive out-of-range, exceeding the positive full-scale value of VREF, the output clips to all 7FFFFFh. Likewise, when the input is negative out-of-range by going below the negative full-scale value of –VREF, the output clips to 800000h. Table 9. Ideal Output Code vs Input Signal INPUT SIGNAL VIN = (AINP – AINN) IDEAL OUTPUT CODE(1) ≥ VREF 7FFFFFh When LVDS signal swings are used, the shift clock is automatically generated internally regardless of the state of SCLK_SEL. In this case, SCLK_SEL cannot be left floating; it must be tied high or low. +VREF 2 23 0 Table 8 summarizes the ADS1672 supported serial clock configurations. 23 Table 8. Supported Serial Clock Configurations SHIFT CLOCK (SCLK) LVDS Must be generated internally CMOS Internal (SCLK_SEL = '0') External (SCLK_SEL = '1') The chip select input (CS) allows multiple devices to share a serial bus. When CS is inactive (high), the serial interface is reset and the data output pins DOUT and DOUT enter a high-impedance state. SCLK is internally generated; the SCLK and SCLK output pins also enter a high-impedance state when CS is inactive. The DRDY and DRDY outputs are always active, regardless of the state of the CS output. CS may be permanently tied low when the outputs do not share a bus. blank blank 22 < -VREF FFFFFFh -1 (2 2 23 23 -1 ) 8000000h 1. Excludes effects of noise, INL, offset and gain errors. CLOCK INPUT (CLK) CHIP SELECT (CS) blank 000000h -VREF 2 DIGITAL OUTPUTS 000001h -1 The ADS1672 requires that an external clock signal be applied to the CLK input pin. The sampling of the modulator is controlled by this clock signal. As with any high-speed data converter, a high-quality clock is essential for optimum performance. Crystal clock oscillators are the recommended CLK source; other sources, such as frequency synthesizers, are usually inadequate. Make sure to avoid excess ringing on the CLK input; keep the trace as short as possible. Measuring high-frequency, large amplitude signals requires tight control of clock jitter. The uncertainty during sampling of the input from clock jitter limits the maximum achievable SNR. This effect becomes more pronounced with higher frequency and larger magnitude inputs. Fortunately, the ADS1672 oversampling topology reduces clock jitter sensitivity over that of Nyquist rate converters, such as pipeline and successive approximation converters, by at least a factor of √32. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 SYNCHRONIZING MULTIPLE ADS1672s ANALOG POWER DISSIPATION The START pin should be applied at power-up and resets the ADS1672 filters. START begins the conversion process, and the START pin enables simultaneous sampling with multiple ADS1672s in multichannel systems. All devices to be synchronized must use a common CLK input. An external resistor connected between the RBIAS pin and the analog ground sets the analog current level, as shown in Figure 38. The current is inversely proportional to the resistor value. Figure 21 and Figure 22 (in the Typical Characteristics) show power and typical performance at values of RBIAS for different CLK frequencies. Notice that the analog current can be reduced when using a slower frequency CLK input because the modulator has more time to settle. Avoid adding any capacitance in parallel to RBIAS, because this additional capacitance interferes with the internal circuitry used to set the biasing. It is recommended that the START pin be aligned to the falling edge of CLK to ensure proper synchronization because the START signal is internally latched by the ADS1672 on the rising edge of CLK. With the CLK inputs running, pulse START on the falling edge of CLK, as shown in Figure 37. Afterwards, the converters operate synchronously with the DRDY outputs updating simultaneously. After synchronization, DRDY is held high until the digital filter has fully settled. ADS1672 RBIAS RBIAS ADS16721 START CLK START1 DRDY DRDY1 AGND CLK Figure 38. External Resistor Used to Set Analog Power Dissipation (Depends on fCLK) ADS16722 START2 DRDY DRDY2 CLK POWER DOWN (PDWN) When not in use, the ADS1672 can be powered down by taking the PDWN pin low. All circuitry shuts down, including the voltage reference. To minimize the digital current during power down, stop the clock signal supplied to the CLK input. Make sure to allow time for the reference to start up after exiting power-down mode. CLK START tSETTLE After the reference has stabilized, allow for the modulator and digital filter to settle before retrieving data. DRDY1 DRDY2 Figure 37. Synchronizing Multiple Converters Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 23 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com POWER SUPPLIES blank Two supplies are used on the ADS1672: analog (AVDD) and digital (DVDD). Each supply must be suitably bypassed to achieve the best performance. It is recommended that a 1µF and 0.1µF ceramic capacitor be placed as close to each supply pin as possible. Connect each supply-pin bypass capacitor to the associated ground. Each main supply bus should also be bypassed with a bank of capacitors from 47µF to 0.1µF. Figure 39 illustrates the recommended method for ADS1672 power-supply decoupling. +3V 0.1mF 0.1mF 58 57 10mF 10mF 56 54 AVDD AGND AGND 53 52 51 50 49 AGND AVDD DVDD DGND DGND DVDD 1 AVDD DVDD 48 2 AGND DGND 47 0.1mF 10mF 3 AGND +5V 0.1mF 10mF 6 AGND ADS1672 7 AVDD 9 AGND 10 AGND 11 AVDD 12 AVDD DGND DGND DGND DGND DVDD DVDD DGND DGND DVDD DGND 17 18 19 20 23 24 25 26 27 31 0.1mF 10mF Figure 39. Power-Supply Decoupling 24 Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 ADS1672 www.ti.com .............................................................................................................................................................. SBAS402A – JUNE 2008 – REVISED JULY 2008 APPLICATION INFORMATION To obtain the specified performance from the ADS1672, the following layout and component guidelines should be considered. 1. Power Supplies: The device requires two power supplies for operation: DVDD and AVDD. For both supplies, use a 10µF tantalum capacitor, bypassed with a 0.1µF ceramic capacitor, placed close to the device pins. Alternatively, a single 10µF ceramic capacitor can be used. The supplies should be relatively free of noise and should not be shared with devices that produce voltage spikes (such as relays, LED display drivers, etc.). If a switching power supply source is used, the voltage ripple should be low (< 2mV). The power supplies may be sequenced in any order. 2. Ground Plane: A single ground plane connecting both AGND and DGND pins can be used. If separate digital and analog grounds are used, connect the grounds together at the converter. 3. Digital Inputs: Source terminate the digital inputs to the device with 50Ω series resistors. The resistors should be placed close to the driving end of the digital source (oscillator, logic gates, DSP, etc.) These resistors help reduce ringing on the digital lines, which may lead to degraded ADC performance. 4. Analog/Digital Circuits: Place analog circuitry (input buffer, reference) and associated tracks together, keeping them away from digital circuitry (DSP, microcontroller, logic). Avoid crossing digital tracks across analog tracks to reduce noise coupling and crosstalk. blank 5. Reference Inputs: Use a minimum 10µF tantalum with a 0.1µF ceramic capacitor directly across the reference inputs, VREFP and VREFN. The reference input should be driven by a low-impedance source. For best performance, the reference should have less than 3µVRMS broadband noise. For references with higher noise, external reference filtering may be necessary. 6. Analog Inputs: The analog input pins must be driven differentially to achieve specified performance. A true differential driver or transformer (ac applications) can be used for this purpose. Route the analog inputs tracks (AINP, AINN) as a pair from the buffer to the converter using short, direct tracks and away from digital tracks. A 1nF to 10nF capacitor should be used directly across the analog input pins, AINP and AINN. A low-k dielectric (such as COG or film type) should be used to maintain low THD. Capacitors from each analog input to ground should be used. They should be no larger than 1/10 the size of the difference capacitor (typically 100pF) to preserve the ac common-mode performance. 7. Component Placement: Place the power supply, analog input, and reference input bypass capacitors as close as possible to the device pins. This placement is particularly important for the small-value ceramic capacitors. Surface-mount components are recommended to avoid the higher inductance of leaded components. Figure 40 to Figure 42 illustrate basic connections and interfaces that can be used with the ADS1672. Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 25 ADS1672 SBAS402A – JUNE 2008 – REVISED JULY 2008 .............................................................................................................................................................. www.ti.com 1kW 10nF +5V +5V 0.1mF 10W OPA211 100W 1kW 100mF 10mF 3V REF5030 0.1mF 0.1mF 1m F 1m F 20MHz Clock Source 64 63 62 61 60 59 55 VREFP VREFP CAP2 VREFN VREFN CAP1 CLK 10W 4 AINN VINN Differential Inputs 10W VINP 100pF 750pF 5 AINP 100pF ADS1672 8 RBIAS 7.5kW 13 VCM 1mF Figure 40. Basic Analog Signal Connection RF 392W RG 383W RS 50W RT 54.9W VSIGNAL 5V RG 392W VIN+ + - VINN THS4520 + VIN- RG 392W + RS 50W CM 2.5V RT 54.9W CM 2.5V - VINN + VINP THS4520 - CM 2.5V Figure 41. Basic Differential Input Signal Interface 5V RG 383W VINP RF 392W 26 CM 2.5V CM 2.5V RF 392W CM 2.5V RF 392W Figure 42. Basic Single-Ended Input Signal Interface Submit Documentation Feedback Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): ADS1672 PACKAGE OPTION ADDENDUM www.ti.com 11-Jul-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty ADS1672IPAG ACTIVE TQFP PAG 64 160 Green (RoHS & no Sb/Br) CU NIPDAU Level-4-260C-72 HR ADS1672IPAGG4 ACTIVE TQFP PAG 64 160 Green (RoHS & no Sb/Br) CU NIPDAU Level-4-260C-72 HR ADS1672IPAGR ACTIVE TQFP PAG 64 1500 Green (RoHS & no Sb/Br) CU NIPDAU Level-4-260C-72 HR ADS1672IPAGRG4 ACTIVE TQFP PAG 64 1500 Green (RoHS & no Sb/Br) CU NIPDAU Level-4-260C-72 HR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 2-Jul-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device ADS1672IPAGR Package Package Pins Type Drawing TQFP PAG 64 SPQ Reel Reel Diameter Width (mm) W1 (mm) 1500 330.0 24.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 13.0 13.0 1.5 16.0 24.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 2-Jul-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADS1672IPAGR TQFP PAG 64 1500 346.0 346.0 41.0 Pack Materials-Page 2 MECHANICAL DATA MTQF006A – JANUARY 1995 – REVISED DECEMBER 1996 PAG (S-PQFP-G64) PLASTIC QUAD FLATPACK 0,27 0,17 0,50 48 0,08 M 33 49 32 64 17 0,13 NOM 1 16 7,50 TYP Gage Plane 10,20 SQ 9,80 12,20 SQ 11,80 0,25 0,05 MIN 1,05 0,95 0°– 7° 0,75 0,45 Seating Plane 0,08 1,20 MAX 4040282 / C 11/96 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Falls within JEDEC MS-026 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated