Micro Chip Fuse Planed final production : Sep.2011 Micro Chip Fuse Type: ERBSE ERBSD ■ Features ● Small size ● Fast-acting and withstanding in-rush current characteristics ■ Approved Safety Standards ● UL248-14 : File No.E194052 ● c-UL(CSA)C22.2 No.248-14 : File No.E194052 ■ Explanation of Part Numbers Product Code Micro Chip Fuse 1 2 3 4 5 6 7 8 9 10 E R B S E 1 R 0 0 U Fusing Characteristics Fast-acting and S withstanding in-rush current Product shape 1608 size E (1.6 mm҂0.8 mm) D 1005 size (1.0 mm҂0.5 mm) U Packaging Punched carrier taping ■ Dimensions in mm (not to scale) ■ Construction Marking Fusing Element Rated Current (A) 0R25 0.25 A 1R50 1.5 A 0R31 0.315 A 2R00 2.0 A 0R37 0.375 A 2R50 2.5 A 0R50 0.5 A 3R00 3.0 A 0R75 0.75 A 4R00 4.0 A 1R00 1.0 A 5R00 5.0 A 1R25 1.25 A a Protective Coating Ceramic Core t Electrode (Outer) L W Trimming Type (inches) ERBSE (0603) ERBSD (0402) Dimensions (mm) L 1.60 ±0.15 1.00±0.10 W ±0.15 a t 0.80 0.30 ±0.20 0.70±0.10 0.50±0.10 0.20±0.15 0.40±0.10 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Dec. 2007 Micro Chip Fuse ■ Ratings ● 1608 Size Part No. Rated Current (A) Marking Code Internal R (m액) at 25 °C max. ERBSE첸R첸첸U 0R50 0R75 1R00 1R25 1R50 2R00 2R50 3R00 4R00 5R00 0.5 0.75 1.0 1.25 1.5 2.0 2.5 3.0 4.0 5.0 F G H J K N O P S T 370 245 155 120 90 60 48 36 28 20 Rated Current ҂100 %/4 hours min. Fusing Current/Fusing Time (at 25 °C) Rated Current ҂200 %/5 seconds max. Rated Current ҂300 %/0.2 seconds max. Rated Voltage (Open Circuit Voltage) Interrupting Rating (at Rated Voltage) 32 VDC 50 A Category Temp. Range (Operating Temp. Range) 35 A −40 °C to +100 °C ● 1005 Size Part No. Rated Current (A) Marking Code Internal R (m액) at 25 °C max. ERBSD첸R첸첸U 0R25 0R31 0R37 0R50 0R75 1R00 1R25 1R50 2R00 2R50 3R00 0.25 0.315 0.375 0.5 0.75 1.0 1.25 1.5 2.0 2.5 3.0 V X Y F G H J K N O P 700 570 460 330 200 135 100 80 53 40 33 Fusing Current/Fusing Time (at 25 °C) Rated Current ҂100 %/4 hours min. Rated Current ҂200 %/5 seconds max. Rated Current ҂300 %/0.2 seconds max. Rated Voltage (Open Circuit Voltage) 24 VDC Interrupting Rating (at Rated Voltage) Category Temp. Range (Operating Temp. Range) 35 A −40 °C to +100 °C Power Derating Curve Rated Load (%) • For Circuit, current rating shall be derated in accordance with the figure on the right. • This current derating curve is for fusing characteristics. 100 70 °C 80 60 40 20 0 100 °C –40 –20 0 20 40 60 80 100 120 140 Ambient Temperature (°C) Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Dec. 2007 Micro Chip Fuse ■ Fusing Characteristics (25 °C typical) ● Type ERBSD 10 1 Fusing Time (s) 1 Fusing Time (s) 0.75 A 1.0 A 1.25 A 1.5 A 2.0 A 2.5 A 3.0 A 10 0.25 A 0.315 A 0.375 A 0.5 A 0.5 A ● Type ERBSE 0.75 A 1.0 A 1.25 A 1.5 A 2.0 A 2.5 A 3.0 A 4.0 A 5.0 A ● I–t Characteristics 0.1 0.01 0.1 0.01 0.001 0.001 ✽ Reference Only 0.0001 0.1 1 100 10 Fusing Current (A) 0.0001 0.1 ✽ Reference Only 1 10 Fusing Current (A) 100 ● I2t–t Characteristics ● Type ERBSE ● Type ERBSD 5.0 A 4.0 A 3.0 A 2.5 A 2.0 A 1.5 A 1.25 A 1.0 A 0.75 A 0.5 A 100 10 0.1 3.0 A 2.5 A 2.0 A 1.5 A 1.25 A 1.0 A 0.75 A 0.5 A 0.375 A 0.315 A 0.25 A 10 1 I2t (A2s) I2t (A2s) 1 100 0.1 0.01 0.01 0.001 0.001 ✽ Reference Only 0.0001 0.0001 0.001 0.01 t (s) 0.1 ✽ Reference Only 1 0.0001 0.0001 0.001 0.01 t (s) 0.1 1 ■ Packaging Methods ● Standard Quantity Type ERBSE ERBSD Kind of Taping Punched Carrier Taping ● Punched Carrier Taping Pitch (P1) 4 mm 2 mm Quantity 5000 pcs./ reel 10000 pcs./ reel ● Taping Reel T Sprocket hole Compartment φC B A T Chip component P1 P2 P0 φB F E W φD0 Taping running direction φA Dimen sions (mm) Type ERBSE ERBSD A B W F E 1.00±0.10 1.80±0.20 ±0.20 ±0.05 8.00 3.50 1.75±0.10 0.65±0.05 1.15±0.05 Dimen sions (mm) Type P1 P2 P0 T φD0 ±0.07 ERBSE 4.00±0.10 ±0.05 ±0.10 +0.10 0.85 2.00 4.00 1.50 –0 ERBSD 2.00±0.10 0.60±0.07 φA Dimensions +0 (mm) 180.0−3.0 φB 60 min. W φC ±1.0 13.0 W 9.0 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. ±1.0 T 11.4±1.0 Dec. 2007 Micro Chip Fuse ■ Recommended Land Pattern C A B Type Dimensions (mm) A B C ERBSE 0.9 2.1 to 2.3 0.8 ERBSD 0.6 1.4 to 1.6 0.5 ■ Recommended Soldering Conditions Recommendations and precautions are described below. ● Recommended soldering conditions for reflow ·Reflow soldering shall be performed a maximum of two times. ·Please contact us for additional information when used in conditions other than those specified. ·Please measure the temperature of the terminals and study every kind of solder and printed circuit board for solderability before actual use. For soldering (Example : Sn/Pb) Preheating Main heating Peak Temperature Peak Temperature Time 140 °C to 160 °C 60 s to 120 s Above 200 °C 30 s to 40 s 235 ± 5 °C max. 10 s For lead-free soldering (Example : Sn/Ag/Cu) Preheating Preheating Heating Main heating Peak Temperature Time 150 °C to 180 °C 60 s to 120 s Above 230 °C 30 s to 40 s max. 260 °C max. 10 s Time <Repair with hand soldering> ● Preheat with a blast of hot air or similar method. Use a soldering iron with a tip temperature of 350 °C or less. Solder each electrode for 3 seconds or less. ● Never touch this product with the tip of a soldering iron. Safety Precautions The following are precautions for individual products. Please also refer to the precautions common to EMI Filters, Fuses, and Sensors(MR Elements) shown on page EX2 of this catalog. 1. Set the rated current so that the current passing through the Micro Chip Fuses (hereafter called the fuses) under normal conditions is within 70% of the rated current. 2. Do not continuously pass a current exceeding the rated current through the fuses. 3. If a pulse exceeding the rated current is applied, such as a rush current or surge current at power-on, take care not to cause unwanted fusing. Calculate the I2t value of the pulse and check the tolerance to the number of pulses according to the I 2t-t characteristic curve before deciding to use the fuses. Before checking the tolerance, consult our sales staff in advance. 4. The fuses are designed to be blown out by a current that is double or greater than the rated current. Ensure that the abnormal current generated when a circuit abnormality occurs in your product is at least double or greater than the rated current of the fuses. In addition, ensure that the abnormal current of your product does not exceed the maximum interrupting current of the fuses. 5. The fuses are designed to be used on the secondary side of a power supply. Do not use them on the primary side. 6. Ensure that the voltage applied to the fuses are within their rated voltage. 7. The fusing characteristics of the fuses are affected by the ambient temperature. Before use, mount the fuses on your products and carefully check and evaluate their operating temperature range. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. Feb. 2006 Safety Precautions (Common precautions for EMI Filters, Fuses, and Sensors[MR Elements]) • When using our products, no matter what sort of equipment they might be used for, be sure to make a written agreement on the specifications with us in advance. The design and specifications in this catalog are subject to change without prior notice. • Do not use the products beyond the specifications described in this catalog. • This catalog explains the quality and performance of the products as individual components. Before use, check and evaluate their operations when installed in your products. • Install the following systems for a failsafe design to ensure safety if these products are to be used in equipment where a defect in these products may cause the loss of human life or other significant damage, such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment, electric heating appliances, combustion/gas equipment, rotating equipment, and disaster/crime prevention equipment. ✽ Systems equipped with a protection circuit and a protection device ✽ Systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault (1) Precautions for use • These products are designed and manufactured for general and standard use in general electronic equipment (e.g. AV equipment, home electric appliances, office equipment, information and communication equipment) • These products are not intended for use in the following special conditions. Before using the products, carefully check the effects on their quality and performance, and determine whether or not they can be used. 1. In liquid, such as water, oil, chemicals, or organic solvent 2. In direct sunlight, outdoors, or in dust 3. In salty air or air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2 4. Electric Static Discharge (ESD) Environment These components are sensitive to static electricity and can be damaged under static shock (ESD). Please take measures to avoid any of these environments. Smaller components are more sensitive to ESD environment. 5. Electromagnetic Environment Avoid any environment where strong electromagnetic waves exist. 6. In an environment where these products cause dew condensation 7. Sealing or coating of these products or a printed circuit board on which these products are mounted, with resin or other materials • These products generate Joule heat when energized. Carefully position these products so that their heat will not affect the other components. • Carefully position these products so that their temperatures will not exceed the category temperature range due to the effects of neighboring heat-generating components. Do not mount or place heat-generating components or inflammables, such as vinyl-coated wires, near these products (except Thermal Cutoffs). • Note that non-cleaning solder, halogen-based highly active fl ux, or water-soluble flux may deteriorate the performance or reliability of the products. • Carefully select a flux cleaning agent for use after soldering. An unsuitable agent may deteriorate the performance or reliability. In particular, when using water or a water-soluble cleaning agent, be careful not to leave water residues. Otherwise, the insulation performance may be deteriorated. (2) Precautions for storage The performance of these products, including the solderability, is guaranteed for a year from the date of arrival at your company, provided that they remain packed as they were when delivered and stored at a temperature of 5 °C to 35 °C and a relative humidity of 45 % to 85 %. (Micro Chip Fuses: Guaranteed for 6 months from the date of arrival at your company) The performance of EMI Filters is guaranteed for 6 months or a year from the outgoing inspection date indicated on the packages, provided that they are stored at a temperature of -5 °C to +40 °C and a relative humidity of 40 % to 60 %. Check the guarantee period in the specifications. The performance of Thermal Cutoffs is guaranteed for a year from the outgoing inspection date indicated on the packages, provided that they are stored at a temperature of -10 °C to +40 °C and a relative humidity of 30 % to 75 %. Even within the above guarantee periods, do not store these products in the following conditions. Otherwise, their electrical performance and/or solderability may be deteriorated, and the packaging materials (e.g. taping materials) may be deformed or deteriorated, resulting in mounting failures. 1. In salty air or in air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2 2. In direct sunlight <Package markings> Package markings include the product number, quantity, and country of origin. In principle, the country of origin should be indicated in English. Feb. 2006 – EX2 –