BeRex BT05AG 5-4000 mhz wideband drive amplifier Datasheet

BT05AG
5-4000 MHz Wideband Drive Amplifier
Device Features





OIP3 = 40.0 dBm @ 1900 MHz
Gain = 20.8 dB @ 900 MHz
Output P1 dB = 22.4 dBm @ 900 MHz
50 Ω Cascadable
Lead-free/RoHS-compliant SOT-89 SMT package
Product Description
Typical Performance1
BeRex’s BT05AG is a high performance and a
high dynamic range amplifier in a low cost
surface mount package(SOT-89) with a RoHS
-compliant, that incorporates reliable heterojunction-bipolar-transistor (HBT) devices
fabricated with InGaP GaAs technology.
This device is designed for use where high
linearity is required and features high OIP3
and P1 with low consumption current
(85mA) and requires a few external matching components such as a DC blocking capacitors on the In/Output pin, a bypass capacitor and a RF choke for the out port.
All devices are 100% RF/DC tested.
Parameter
Applications
Vcc
Bypass
RF Choke
RF In
RF Out
BT05AG
DC
Block
DC
Block
Unit
900
1900
2450
3500
MHz
Gain
20.8
16.3
14.3
11.1
dB
S11
-14.0
-20.0
-22.0
-16.0
dB
-12.0
-12.0
-12.0
-13.0
dB
37.0
22.4
4.5
40.0
19.5
4.4
37.5
23.0
4.3
40.0
22.8
4.5
dBm
dBm
dB
S22
2
OIP3
P1dB
Noise Figure
1
Device performance _ measured on a BeRex evaluation board at 25°C, 50 Ω system.
2
OIP3 _ measured with two tones at an output of 10 dBm per tone separated by 1 MHz.
Min.
Bandwidth
IC @ (Vc = 5V)
VC
RTH
 Base station Infrastructure/RFID
 Commercial/Industrial/Military wireless system
Application Circuits
Frequency
Typical
5
75
85
5.0
50
Max.
Unit
4000
95
MHz
mA
V
°C/W
Absolute Maximum Ratings
Parameter
Operating Case Temperature
Storage Temperature
Junction Temperature
Operating Voltage
Supply Current
Input RF Power
Rating
-40 to +85
-55 to +155
+220
Unit
°C
°C
°C
+7.0
180
23
V
mA
dBm
*Operation of this device above any of these parameters may result in permanent damage.
*external matching circuit: refer to the page 5 to 11.
BeRex
●website: www.berex.com
● email: [email protected]
1
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
V-I Characteristics
BeRex SOT89 Evaluation Board
BeRex
Evaluation Board
*Dielectric constant _ 4.2 *RF pattern width 52mil *31mil thick FR4 PCB
Typical Device Data
S-parameters (Vc=5V, Ic=84mA, T=25°C)
BeRex
●website: www.berex.com
● email: [email protected]
2
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
S-Parameter
(Vdevice = 5.0V, Icc = 84mA, T = 25 °C, calibrated to device leads)
Freq
[MHz]
S11
S11
S21
S21
S12
S12
S22
S22
Mag
Ang
Mag
Ang
Mag
Ang
Mag
Ang
100
500
1000
1500
2000
2500
3000
3500
-10.6001
-6.89632
-4.83571
-4.36842
-4.49519
-4.82222
-4.64574
-3.85543
-176.08
171.969
137.774
107.055
77.2739
43.2334
3.39018
-35.846
24.3773
22.4951
19.3111
16.5624
14.5732
13.1214
11.7047
9.92492
166.26
118.889
75.4763
42.7846
13.4329
-15.725
-45.735
-74.765
-29.173
-28.510
-27.637
-27.010
-26.080
-25.166
-24.318
-25.101
-0.828
-5.512
-16.88
-29.70
-41.79
-58.33
-79.25
-100.4
-21.805
-20.525
-17.519
-16.447
-17.536
-22.101
-27.037
-16.664
-27.056
-120.815
170.039
137.451
118.289
99.7268
4.66192
-50.8784
4000
-3.0184
-66.883
8.4767
-100.82
-24.247
-119.41
-11.732
-71.031
WCDMA 6FA 2140 -55dBc
BeRex
●website: www.berex.com
● email: [email protected]
3
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
WCDMA 6FA 2140 -60dBc
ACLR
BeRex
●website: www.berex.com
● email: [email protected]
4
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
Application Circuit: 900 MHz
Schematic Diagram
BOM
C1
C2
C3
+5V
L1
RFin
C4
C7
RFout
C5
BT05AG
C6
L2
C1
C2
C3
C4
C5
C6
C7
L1
L2
Tolerance
100pF
1000pF
10uF
100pF
100pF
1pF
4.7pF
39nH
5.6nH
±5%
±5%
±20%
±5%
±5%
±5%
±5%
±5%
±5%
Note:
10uF
1000 pF
1.
PCB: 31mil thick FR4
2.
Distance between the center of the series cap
(C7) and the input pin of BT05AG _ 2.0mm.
3.
Distance between the center of the shunt inductor(L2) and the input pin of BT05AG _ 4.1mm.
4.
Distance between the center of the shunt cap
(C6) and the input pin of BT05AG _ 6.5mm.
100pF
100 pF
BT05AG
BT013
4.7pF
100pF
1pF
39nH
BB
100pF
B
5.6nH
Typical Performance
0
0
+25C
+25C
-5
-5
+85C
S22 [dB]
S11 [dB]
-30C
-30C
-10
-15
-10
-15
-20
800
+85C
850
900
950
1000
-20
800
850
Freq [MHz]
BeRex
●website: www.berex.com
900
950
1000
Freq [MHz]
● email: [email protected]
5
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
25
23
70
60
22
20
50
20
15
40
30
10
19
20
+25C
Po
5
-30C
18
G
+85C
0
850
900
950
0
-20
1000
-14
-8
40
0
38
-10
34
32
+25C
-30C
+85C
-40
-50
-70
26
12
+85C
-30
-60
-30C
10
10
+25C
-20
36
28
4
900MHz, 885KHz offset
9-Ch FWD, IS-95
ACPR [dBc]
OIP3 [dBm]
F1=900MHz, F2=901MHz
30
-2
Pin [dBm ]
Freq [MHz]
14
16
18
-80
10
12
Po, 2tone [dBm ]
BeRex
10
PAE
17
800
PAE [%]
Po, G
S21 [dB]
21
●website: www.berex.com
14
16
18
Po [dBm ]
● email: [email protected]
6
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
Application Circuit: 1900 MHz
Schematic Diagram
BOM
C1
C2
C3
+5V
L1
RFin
L2
C4
RFout
C5
BT05AG
C6
C7
C1
C2
C3
C4
C5
C6
C7
L1
L2
Tolerance
100pF
100pF
10uF
100pF
100pF
2pF
1pF
39nH
3.3nH
±5%
±5%
±20%
±5%
±5%
±5%
±5%
±5%
±5%
Note:
10uF
1000 pF
1.
PCB: 31mil thick FR4
2.
Distance between the center of the shunt cap
(C6) and the input pin of BT05AG _ 1.8mm.
3.
Distance between the center of the series inductor(L2) and the output pin of BT05AG _ 3.5mm.
4.
Distance between the center of the shunt cap
(C7) and the output pin of BT05AG _ 5.9mm.
100pF
100 pF
BT05AG
BT013
39nH
BB
100pF
100pF
B
2pF
3.3nH 1pF
Typical Performance
BeRex
●website: www.berex.com
● email: [email protected]
7
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
BeRex
●website: www.berex.com
● email: [email protected]
8
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
Application Circuit: 2450MHz
Schematic Diagram
BOM
C1
C2
C3
+5V
L1
RFin
C4
RFout
C5
BT05AG
C6
C1
C2
C3
C4
C5
C6
L1
100pF
1000pF
10uF
100pF
100pF
1.2pF
39nH
Tolerance
±5%
±5%
±20%
±5%
±5%
±5%
±5%
Note:
10uF
1000 pF
100pF
100 pF
BT05AG
BT013
BB
100pF
B
1.
PCB: 31mil thick FR4
2.
Distance between the center of the shunt cap
(C6) and the input pin of BT05AG _ 0.5mm.
39nH
100pF
1.2pF
Typical Performance
BeRex
●website: www.berex.com
● email: [email protected]
9
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
BeRex
●website: www.berex.com
● email: [email protected]
10
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
Application Circuit: 3500MHz
Schematic Diagram
BOM
C1
C2
+5V
C3
L1
RFin
L2
C4
RFout
BT05AG
C6
C5
C7
C1
C2
C3
C4
C5
C6
C7
L1
L2
Tolerance
100pF
1000pF
10uF
18pF
18pF
0.75pF
0.5pF
33nH
2.7nH
±5%
±5%
±20%
±5%
±5%
±5%
±5%
±5%
±5%
Note:
10uF
1000 pF
100pF
100 pF
BT05AG
BT013
2.7nH
33nH
BB
18pF
PCB: 31mil thick FR4
2.
Distance between the center of the series inductor(L2) and the input pin of BT05AG _ 2.0mm.
3.
Distance between the center of the shunt cap(C6)
and the input pin of BT05AG _ 0.5mm.
4.
Distance between the center of the shunt cap(C7)
and the output pin of BT05AG _ 10.0mm.
18pF
B
0.75pF
1.
0.5pF
Typical Performance
BeRex
●website: www.berex.com
● email: [email protected]
11
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
BeRex
●website: www.berex.com
● email: [email protected]
12
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
Package Outline Dimension
Suggested PCB Land Pattern and PAD Layout
PCB Land Pattern
0.40
1.30
PCB Mounting
0.40
Ø0.40
0.40
0.75
1.20
2.15
1.20
0.50
0.45
1.20
1.20
2.80
1.50
1.00
0.65
0.35
Note : All dimension _ millimeters
PCB lay out _ on BeRex website
BeRex
●website: www.berex.com
● email: [email protected]
13
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
BT05AG
5-4000 MHz Wideband Drive Amplifier
Package Marking
Tape & Reel
SOT89
Packaging information:
Tape Width (mm): 12
Reel Size (inches): 7
Device Cavity Pitch (mm): 8
YY = Year, WW = Working Week,
XX = Wafer No.
Devices Per Reel: 1000
Lead plating finish
100% Tin Matte finish
(All BeRex products undergoes a 1 hour, 150 degree C, Anneal bake to eliminate
thin whisker growth concerns.)
MSL / ESD Rating
ESD Rating:
Class 1B
Value:
Passes <1000V
Test:
Human Body Model (HBM)
Standard:
JEDEC Standard JESD22-A114B
MSL Rating:
Level 1 at +265°C convection reflow
Standard:
JEDEC Standard J-STD-020
NATO CAGE code:
2
BeRex
N
9
6
F
●website: www.berex.com
● email: [email protected]
14
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2010 BeRex
Rev. E
Similar pages