DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 16-Channel, Current-Input Analog-to-Digital Converter FEATURES DESCRIPTION 1 • SINGLE-CHIP SOLUTION TO MEASURE 16 LOW-LEVEL CURRENTS • INTEGRATING I-TO-V CONVERSION FRONT-END • PROGRAMMABLE FULL-SCALE : 3pC to 12pC • ADJUSTABLE SPEED: – Data Rate Up To 100kSPS – Integration Time Down To 10µs • ANALOG SUPPLY: +5V • DIGITAL SUPPLY: +3.3V 2 For each of the 16 inputs, the DDC316 provides a dual-switched integrator front-end. This configuration allows for continuous current integration: while one integrator is being digitized by the on-chip ADC, the other is integrating the input current. Adjustable integration times range from 10µs to 1ms. The DDC316 provides a serial interface of the output data, either multiplexed onto a single data output pin or parallel on four output pins. The output mode can be selected based on the available integration time. APPLICATIONS • • • The DDC316 is a 16-bit, 16-channel, current-input analog-to-digital converter (ADC). It combines both current-to-voltage and analog-to-digital (A/D) conversion so that 16 separate low-level current output devices (such as photodiodes) can be directly connected to its inputs and digitized. CT SCANNER DAS PHOTODIODE SENSORS X-RAY DETECTION SYSTEMS The DDC316 uses a +5V analog supply and a +3.3V digital supply. Operating over the temperature range of 0°C to +70°C, the DDC316 is offered in a BGA-64 package. Protected by US Patent #5841310 AVDD IN1 VREF DVDD DDC316 I to V CLK IN2 Control I to V CONV DIN_CFG RESET IN3 I to V DVALID ADCs DIN IN4 DCLK I to V Serial Interface DOUT1 DOUT2 IN16 DOUT3 DOUT4 I to V AGND DGND 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2008–2009, Texas Instruments Incorporated DDC316 SBAS370A – MARCH 2008 – REVISED APRIL 2009......................................................................................................................................................... www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. ABSOLUTE MAXIMUM RATINGS (1) AVDD to AGND –0.3V to +6V DVDD to DGND –0.3V to +3.6V AGND to DGND ±0.2V VREF Input to AGND 2.0V to AVDD + 0.3V Analog Input to AGND –0.3V to +0.7V Digital Input Voltage to DGND –0.3V to DVDD + 0.3V Digital Output Voltage to DGND –0.3V to AVDD + 0.3V Operating Temperature 0°C to +70°C Storage Temperature –60°C to +150°C Junction Temperature (TJ) (1) 2 +150°C Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 ELECTRICAL CHARACTERISTICS At TA = +25°C, AVDD = +5V, DVDD = +3.3V, VREF = +4.096V, tINT = 20µs, Range = 12pC, Format = 16 bits, CLK = 40MHz, and HI_SPEED Bit = 1, unless otherwise noted. DDC316 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Range 1 2.4 3 3.6 pC Range 2 4.8 6 7.2 pC Range 3 9.6 12 14.4 pC Negative Full-Scale Range –1.786% of Positive Full-Scale Range ANALOG INPUT RANGE pC DYNAMIC CHARACTERISTICS Data Rate Integration Time, tINT 100 kSPS HI_SPEED Bit = 1 20 1,000 µs HI_SPEED Bit = 0 10 20 µs 1 40 MHz 40 MHz 20 MHz System Clock Input Data Clock (DCLK) Daisy-Chain Readback ACCURACY Resolution 12 Noise, Low-Level Input (1) CSENSOR (2) = 10pF Integral Linearity Error (4) Input Bias Current TA = +25°C Range Error Match (5) Range Sensitivity to VREF VREF = 4.096 ± 0.1V 16 Bits 3.5 6.0 LSB (3) 8 16 LSB (3) ±2 ±10 pA 0.2 1 % of FSR (6) 1:1 Offset Error ±50 ±200 LSB (3) Offset Error Match (5) ±75 ±400 LSB (3) Low-Level Input (< 1% FSR) ±2 ±10 mV at DC 40 LSB (3)/V ±1 LSB/°C Continuous Readings Over 1-Minute Intervals After a 10-Minute Warm-Up <1 LSB ±10 µV/°C Range Drift (8) 25 ppm/°C Range Drift Match (5) ±10 ppm/°C DC Bias Voltage (7) Power-Supply Rejection Ratio PERFORMANCE OVER TEMPERATURE Offset Drift Offset Drift Stability DC Bias Voltage Drift (7) Input Bias Current Drift Doubles Every +10°C REFERENCE Voltage 4.000 4.096 4.200 V DIGITAL INPUT/OUTPUT Logic Levels VIH 0.8DVDD DVDD + 0.1 V VIL –0.1 0.2DVDD V VOH IOH = –100µA VOL IOL = 100µA 0.4 V 0 < VIN < DVDD ±10 µA Input Current (IIN) DVDD – 0.4 Data Format (9) (1) (2) (3) (4) (5) (6) (7) (8) (9) V Straight Binary Input is less than 1% of full-scale. CSENSOR is the capacitance seen at the DDC316 inputs from wiring, photodiode, etc. LSB refers to 16-bit resolution. A best-fit line is used in measuring nonlinearity. Matching between side A and side B of the same input. FSR is full-scale range. Voltage produced by the DDC316 at its input that is applied to the sensor. Range drift does not include external reference drift. Data format is Straight Binary with a small offset. The number of bits in the output word is controlled by the Format bit. Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 3 DDC316 SBAS370A – MARCH 2008 – REVISED APRIL 2009......................................................................................................................................................... www.ti.com ELECTRICAL CHARACTERISTICS (continued) At TA = +25°C, AVDD = +5V, DVDD = +3.3V, VREF = +4.096V, tINT = 20µs, Range = 12pC, Format = 16 bits, CLK = 40MHz, and HI_SPEED Bit = 1, unless otherwise noted. DDC316 PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Analog Power-Supply Voltage (AVDD) 4.75 5.0 5.25 V Digital Power-Supply Voltage (DVDD) 3 3.3 3.6 V POWER-SUPPLY REQUIREMENTS Supply Current Analog Current Internal Reference Buffer BUFDIS Bit = 0 95 mA External Reference Buffer BUFDIS Bit = 1 85 mA DVDD = +3.3V 5 mA Internal Reference Buffer BUFDIS Bit = 0, DVDD = +3.3V 540 External Reference Buffer BUFDIS Bit = 1, DVDD = +3.3V 440 Internal Reference Buffer BUFDIS Bit = 0, DVDD = +3.3V 31 External Reference Buffer BUFDIS Bit = 1, DVDD = +3.3V 28 Digital Current Total Power Dissipation mW 640 mW Per Channel Power Dissipation 4 Submit Documentation Feedback mW/channel 40 mW/channel Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 PIN CONFIGURATION GXG AND ZXG PACKAGES BGA-64 (TOP VIEW) Columns H G F E D C B A IN1 IN3 IN9 IN12 IN5 IN7 IN13 IN15 1 IN2 IN4 IN10 IN11 IN6 IN8 IN14 IN16 2 AGND AGND AGND AGND AGND AGND AGND AGND 3 AVDD AVDD AVDD AVDD AVDD AGND VREF_IN VREF 4 AGND AGND AGND AGND AGND AGND AGND 5 AVDD AVDD AVDD AVDD AGND DGND VREF Rows QGND VREF 6 DVALID DIN_CFG DGND DIN AGND DGND DVDD RESET 7 DOUT1 DOUT2 DOUT3 DOUT4 DCLK CLK DVDD CONV 8 PIN DESCRIPTIONS PIN LOCATION FUNCTION DESCRIPTION IN1–16 1A-1H, 2A-2H Analog Input Analog Inputs for Channels 1 to 16 AGND 3A-3H, 4C, 5A-5G, 6D, 7D Analog VREF 4A, 6A, 6B Analog Input Voltage Reference for Internal Reference Buffer Mode VREF_IN 4B Analog Input Voltage Reference for External Reference Buffer Mode AVDD 4D-4H, 6E, 6F, 6G, 6H Analog Analog Power Supply, +5V Nominal QGND 5H Analog Quiet Analog Ground Digital Ground Analog Ground DGND 6C, 7C, 7F Digital RESET 7A Digital Input DVDD 7B, 8B Digital DIN 7E Digital Input Serial Data Input for Daisy-Chain DIN_CFG 7G Digital Input Configuration Register Data Input DVALID 7H Digital Output CONV 8A Digital Input Conversion Control Input; 0 = Integrate on Side B, 1 = Integrate on Side A Digital Reset, Active Low Digital Power Supply, +3V Nominal Data Valid Output, Active Low CLK 8C Digital Input Master Clock Input DCLK 8D Digital Input Serial Data Clock Input DOUT4-1 8E-8H Digital Output Serial Data Output Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 5 DDC316 SBAS370A – MARCH 2008 – REVISED APRIL 2009......................................................................................................................................................... www.ti.com TIMING DIAGRAMS tCLK tCLKPW CLK tCLKPW CONV tINTB tINTA tMEAS DVALID tDCDV DIN tDIDC tDCDI tCNDC DCLK tDVDO DOUT(1) tDOHD tCNDC tDCLKPW tDOPD MSB tDCLK tDCLKPW LSB Side B Data Side A Data NOTE: (1) DOUT1 in TDM data output mode; DOUT1 through DOUT4 in parallel data output mode. Figure 1. Serial Interface Timing TIMING REQUIREMENTS FOR Figure 1 At TA = 0°C to +70°C and DVDD = 3V to 3.6V, unless otherwise noted. SYMBOL tCLK tCLKPW tINTA,B UNIT 1000 ns 0.4 tCLK periods 1000 tCLK periods HI_SPEED bit = 0, CLK = 40MHz 10 25 µs HI_SPEED bit = 1 800 40,000 tCLK periods HI_SPEED bit = 1, CLK = 40MHz 20 1000 HI_SPEED bit = 0 tDIDC Setup time from DIN to rising edge of DCLK 2 tDCDI Hold time for DIN after rising edge of DCLK 0 tDCLK MAX 400 Time required to perform measurement (1) TYP HI_SPEED bit = 0 tMEAS tDCDV HI_SPEED bit = 1 Falling edge of DVALID to valid DOUT tCLK periods 544 tCLK periods ns ns 6 Falling edge of first DCLK to rising edge of DVALID µs 274 10 19 ns ns DCLK period (1/fDCLK) 25 ns tDCLKPW DCLK pulse width, positive or negative 0.4 tDCLK periods tDOPD (1) Propagation delay from the falling edge of DCLK to valid DOUT1 tDOHD (1) tCNDC 6 MIN 25 CLK pulse width, positive or negative Integration time for sides A and B tDVDO (1) (1) DESCRIPTION CLK period (1/fCLK) 21 ns Hold time during which previous DOUT1 is valid after falling edge of DCLK 5 ns Time between CONV toggle and data retrieval 5 ns Output load = 100kΩ || 10pF Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 CLK tSC DIN_CFG 1 0 1 0 CFG Bit 15 tHC CFG Bit 0 tDVC DVALID tDCDV DCLK tDVDO tDOPD tDOHD CFG Bit 15 DOUT1 CFG Bit 0 Figure 2. Configuration Register Read/Write Timing TIMING REQUIREMENTS FOR Figure 2 At TA = 0°C to +70°C and DVDD = 3.0V to 3.6V, unless otherwise noted. SYMBOL MIN TYP tSC Valid DIN_CFG to CLK falling edge; setup time 1 12 ns tHC Valid DIN_CFG to CLK falling edge; hold time 3 12 ns Delay of DVALID from falling edge of CLK 18 ns tDVC (1) tDCDV (1) (1) DESCRIPTION Falling edge of first DCLK to rising edge of DVALID 19 tDVDO (1) Delay from DVALID falling edge to valid CFG bit 15 on DOUT1 6 tDOPD (1) Propagation delay from the falling edge of DCLK to valid DOUT1 tDOHD (1) Hold time during which previous DOUT1 is valid after falling edge of DCLK MAX UNIT ns 10 ns 21 ns 5 ns Output load = 100kΩ || 10pF Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 7 DDC316 SBAS370A – MARCH 2008 – REVISED APRIL 2009......................................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS At TA = +25°C, unless otherwise indicated. NOISE vs CSENSOR NOISE vs CSENSOR 25 Noise (16-Bit LSBs of FSR, rms) HI_SPEED Bit = 1 20 Range 1 15 Range 2 10 Noise (16-Bit LSBs of FSR, rms) CSENSOR (pF) Range 1 Range 2 Range 3 0 10 20 30 50 100 10.2 13.1 17.5 18.6 22.3 34.3 5.6 7.2 9.2 9.7 11.6 17.8 3.3 4.1 5.1 5.4 6.4 9.4 NOTE: HI_SPEED bit = 1. 5 Range 3 0 0 5 10 15 20 25 30 CSENSOR (pF) Figure 3. 8 Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 THEORY OF OPERATION GENERAL DESCRIPTION The DDC316 contains 16 identical input channels that perform the function of current-to-voltage integration, followed by a multiplexed A/D conversion. Integration time is directly controlled via the CONV pin. Each input uses a dual-switched integrator so that the current-to-voltage integration can be continuous over AVDD VREF time. The 16 integrators from one side of the inputs are digitized, while the other 16 are integrating to achieve continuous charge collection. The results from the conversion are stored in a serial output shift register. The DVALID output goes low when the shift register contains valid data. A block diagram of the DDC316 is shown in Figure 4. VREF_IN DVDD CLK IN1 Dual Switched Integrator Configuration and Control CONV DIN_CFG IN2 Dual Switched Integrator RESET ADC 1 IN3 Dual Switched Integrator DVALID IN4 DIN Dual Switched Integrator DCLK Digital Input/Output IN13 DOUT1 Dual Switched Integrator DOUT2 DOUT3 IN14 Dual Switched Integrator DOUT4 ADC 4 IN15 Dual Switched Integrator IN16 Dual Switched Integrator AGND DGND Figure 4. DDC316 Block Diagram Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 9 DDC316 SBAS370A – MARCH 2008 – REVISED APRIL 2009......................................................................................................................................................... www.ti.com BASIC INTEGRATION CYCLE The topology of the front-end of the DDC316 is an analog integrator, as shown in Figure 5. In this diagram, only input IN1 is shown. The input stage consists of an operational amplifier, a selectable feedback capacitor network (CF), and several switches that implement the integration cycle. The timing relationships of all of the switches shown in Figure 5 are illustrated in Figure 6. Note that Figure 6 conceptualizes the operation of the integrator input stage of the DDC316 and should not be used as an exact timing tool for design. SREF VREF 1.5pF Range[1] 0.75pF Range[0] 0.75pF Input Current SINTA SREF IN1 SADC1A SRESET ESD Protection Diodes Photodiode To Converter Integrator A SINTB Integrator B (same as A) Figure 5. Basic Integration Configuration for Input 1 Integrate on Side B Integrate on Side A Integrate on Side B CONV CLK SINTA SINTB SREF SRESET Integrate Convert Wait Wait Wait Reset Convert Wait Configuration of Integrator A Reset SADC1A VREF Integrator A Voltage Output Figure 6. Conceptual Basic Integration Timing Diagram of Integrator A (as Illustrated in Figure 5) 10 Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 Figure 7 shows the block diagrams of the five states of the front end integrator. The conversion starts with the integrator being configured as shown in Figure 7a. In this state, the ADC converts the integrated value of side A of the previous phase. Once the conversion is done, the integrator waits until the ADC finishes converting the other three integrated values (Figure 7b). At the completion of all four A/D conversions, the charge on the integrator capacitor (CF) is reset with SREF and SRESET (see Figure 7c). In this manner, the selected capacitor is charged to the reference voltage, VREF. Once the integration capacitor is charged, SREF and SRESET are switched so that VREF is no longer connected to the amplifier circuit while it waits to begin integrating (see Figure 7d). With the rising edge of CONV, SINTA closes, which begins the integration of side A. This process puts the integrator stage into Integrate mode (see Figure 7e). Charge from the input signal is collected on the integration capacitor, causing the voltage output of the amplifier to decrease. The falling edge of CONV stops the integration by switching the input signal from side A to side B (SINTA and SINTB). Before the falling edge of CONV, the signal on side B was converted by the ADC and reset during the time that side A was integrating. With the falling edge of CONV, side B starts integrating the input signal. At this point, the output voltage of the side A operational amplifier is presented to the input of the ADC, and the entire cycle repeats. This internal switching network is controlled externally with the convert pin (CONV) and the system clock (CLK). For the best noise performance, CONV must be synchronized with the rising edge of CLK. It is recommended that CONV toggle within ±5ns of the rising edge of CLK. The noninverting inputs of the integrators are connected to ground. Consequently, the DDC316 analog ground should be as clean as possible. SREF CF CF SREF VREF SINT VREF SINT SREF IN SREF IN To Converter SRESET SADC SRESET SADC a) Convert Configuration b) Wait to Reset Configuration SREF CF CF SREF VREF SINT To Converter VREF SINT SREF SREF IN IN To Converter SRESET SADC SRESET SADC To Converter d) Wait to Integrate Configuration c) Reset Configuration CF SREF VREF SINT SREF IN SRESET SADC To Converter e) Integrate Configuration Figure 7. Diagrams for the Five Configurations of DDC316 Front-End Integrators Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 11 DDC316 SBAS370A – MARCH 2008 – REVISED APRIL 2009......................................................................................................................................................... www.ti.com FREQUENCY RESPONSE Ranges The frequency response of the DDC316 is set by the front-end integrators and is consistent with a traditional continuous time integrator, as shown in Figure 8. By adjusting tINT, the user can change the 3dB bandwidth and the location of the notches in the response. The frequency response of the ADC that follows the front-end integrator is of no consequence because the converter samples a held signal from the integrators. That is, the input to the ADC is always a DC signal. Aliasing can occur because the output of the front-end integrators are sampled. Whenever the frequency of the input signal exceeds one-half of the sampling rate, the signal folds back down to lower frequencies. There are three different capacitors available on-chip for both sides of every channel in the DDC316. The range control bits (Range[1:0]) change the capacitor value for all integrators. Consequently, all inputs and both sides of each input always have the same full-scale (FS) range. Table 1 shows the capacitor value selected for each range selection. Table 1. Range Selection RANGE RANGE[1:0] BITS CF (pF, typ) INPUT RANGE (pC, typ) 1 00 0.75 –0.0469 to 3 2 01 1.5 –0.0938 to 6 3 10 3 –0.1876 to 12 0 Resolution Gain (dB) -10 -20 -30 -40 -50 0.1 tINT 1 tINT 10 tINT 100 tINT Frequency Figure 8. DDC316 Frequency Response The DDC316 provides three different resolutions for the convenience of the user. The user can select the resolution needed for the application and the time available for data retrieval. The three available resolutions are 16-bit, 14-bit, and 12-bit. The serial output data from the DDC316 are provided in an offset binary code, as shown in Table 2. The RES bits in the configuration register select how many bits are used in the output word. When 12-bits are selected, the last four bits are truncated; when 14-bits are chosen, the last two bits are truncated. Note that an offset is included in the output to allow slightly negative inputs (for example, from board leakages) from clipping the reading. The offset is approximately 1.8% of the positive full-scale. OPERATION SETTINGS Data Format The DDC316 provides different settings of operation to provide flexibility in terms of range, resolution, etc. The settings are programmable using an on-chip register and are described in the following sections. The DDC316 outputs 12 to 16 bits of data depending on the selected resolution. The format is straight binary with an offset to help prevent leakage currents from the printed circuit board (PCB), or the sensors forcing a clipping on the negative full-scale. Table 2 summarizes the ideal output codes for the different resolutions. Table 2. Ideal Output Code (1) vs Input Signal (1) 12 INPUT SIGNAL IDEAL OUTPUT CODE RESOLUTION = 16 BITS IDEAL OUTPUT CODE RESOLUTION = 14 BITS IDEAL OUTPUT CODE RESOLUTION = 12 BITS ≥ 100% FS 1111 1111 1111 1111 1111 1111 1111 11 1111 1111 1111 0.07019% FS 0000 0100 1100 0000 0000 0100 1100 00 0000 0100 1100 0.02136% FS 0000 0100 1010 0000 0000 0100 1010 00 0000 0100 1010 0.00305% FS 0000 0100 1001 0100 0000 0100 1001 01 0000 0100 1001 0.001525% FS 0000 0100 1001 0011 0000 0100 1001 00 0000 0100 1001 0% FS 0000 0100 1001 0010 0000 0100 1001 00 0000 0100 1001 –1.7857% FS 0000 0000 0000 0000 0000 0000 0000 00 0000 0000 0000 Excludes the effects of noise, INL, offset, and gain errors. Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 Data Output Modes The DDC316 provides two data output modes: time division multiplexed (TDM) and parallel. In TDM mode, data from all 16 channels are output on a single data output line, DOUT1, as shown in Figure 9. In this mode, DOUT2 through DOUT4 are not used and forced to logic low. In parallel output mode, as shown in Figure 10, four channels of data are output on the four DOUT lines, DOUT1 thorough DOUT4. In either mode, the most significant bit (MSB) is shifted out first. CLK CONV 256 DCLKs (16-Bit Resolution) DVALID DCLK DOUT1 TDM Data for Inputs 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16 DOUT2 DOUT3 DOUT4 Figure 9. TDM Data Output CLK CONV 64 DCLKs (16-Bit Resolution) DVALID DCLK DOUT1 Data for Inputs 1, 2, 3, 4 DOUT2 Data for Inputs 5, 6, 7, 8 DOUT3 Data for Inputs 9, 10, 11, 12 DOUT4 Data for Inputs 13, 14, 15, 16 Figure 10. Parallel Data Output Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 13 DDC316 SBAS370A – MARCH 2008 – REVISED APRIL 2009......................................................................................................................................................... www.ti.com MINIMUM INTEGRATION TIME DATA RETRIEVAL TIME The minimum integration time of the DDC316 is set by the master clock (CLK) and the HI_SPEED bit, as shown in Table 3. The integration time specification must always be met for both side A and side B integrations (tINTA and tINTB). Failure to meet integration time specifications gives invalid conversion results. The available time for retrieving the conversion data (tRETRV) from the DDC316 is the difference between the integration time (tINT) and the measurement time (tMEAS), as shown in Figure 11. Retrieval begins after DVALID goes low, and must complete before CONV toggles, for optimal noise performance (see the tCNDC timing specification). Table 3. Minimum Integration Times Sometimes, it is not possible to retrieve all of the data in time when using the TDM data output mode; for example, when integration times are short and DCLK is slow. In these cases, using the parallel data output mode will help because the required time for retrieval decreases by a factor of four. HI_SPEED VALID BIT RESOLUTIONS MINIMUM INTEGRATION TIME (MINIMUM tINT) 0 12-bit only 400 tCLK periods 10µs (for CLK = 40MHz) 1 12-bit to 16-bit 800 tCLK periods 20µs (for CLK = 40MHz) tINT CONV When operating with the HI_SPEED bit set to 0, the DDC316 operates internally at a higher speed and the performance is reduced to fundamentally 12 bits. It is recommended, therefore, that the RES[1:0] bits should be set to 12-bit resolution when HI_SPEED = 0. This will provide more flexibility in retrieving data, because the time required to read back the conversion results is shorter. tMEAS tRETRV DVALID tCNDC DCLK DOUT Figure 11. Data Retrieval Time 14 Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 CONFIGURATION REGISTER The DDC316 configuration shown in Table 4 is controlled by and configured with an on-chip, 16-bit configuration register. Table 4. Configuration Register Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 1 MODE RES[1] RES[0] RANGE[1] RANGE[0] 0 HI_SPEED Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TM[1] TM[0] 0 BUFDIS 0 0 0 0 The following section gives a brief description of the programmable bits and the method to program the bits. Note that in the event of an external reset or a power-on reset, all the configuration bits are set to default values. The bits need to be reprogrammed as needed after a reset. Bit Descriptions Bit 15 Unused bit. This bit must always be set to one. During a power-up or reset event, this bit is set to zero and must be programmed to one. Bit 14 MODE—Data Output Mode. This bit selects between the parallel and serial data output (time division multiplexing, or TDM) modes, as shown in Table 5. Table 5. Data Output Mode Bits 13-12 MODE DATA OUTPUT MODE 0 Parallel, using DOUT1, DOUT2, DOUT3, and DOUT4 (default) 1 Serial, time division multiplexed (TDM) on DOUT1 RES[1:0]—Output Data resolution. These bits set the output data resolution. The value of the output resolution is the same for RES[1:0] = '10' and RES[1:0] = '11'. Table 6. Output Data Resolution RES[1:0] OUTPUT RESOLUTION 00 16 Bits (default) 01 14 Bits 10 12 Bits 11 Bits 11-10 RANGE[1:0]—Full-Scale Input Range. These range bits set the value of the integration capacitors that are used in the dual-switched integrators. Table 7 shows the three different capacitor values available. The value of the maximum input charge is the same for RANGE = '10' and RANGE = '11'. Table 7. Full-Scale Range RANGE[1:0] MAXIMUM INPUT CHARGE 00 3pC (default) 01 6pC 10 12pC 11 Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 15 DDC316 SBAS370A – MARCH 2008 – REVISED APRIL 2009......................................................................................................................................................... www.ti.com Bit 9 Unused bit. This bit is reset to zero and must always be set to zero. Bit 8 HI_SPEED—High-Speed Operation Selection. This bit sets which speed (normal or high) will be used. The default is normal speed, and is the generally recommended operating condition. However, if shorter integration times are needed than are supported during normal operation, then high-speed mode is available. Note that performance reduces to the 12-bit level during high-speed mode. Table 8. High-Speed Mode Selection HI_SPEED Bits 7-6 SPEED 0 High speed 1 Normal speed (default) TM[1:0]—Test Mode Selection. Test mode (TM) bits allow for configuration of the device to operate in either normal mode or test modes for verification purposes, as shown in Table 9. The test modes are provided as a means of evaluating the DDC316 noise. In test mode 1, the inputs (IN1 through IN16) are disconnected from the DDC316 integrators to enable the user to measure a zero input signal, regardless of the current supplied to the DDC316 by the external sensor. In test mode 2, the inputs (IN1 through IN16) are disconnected from the DDC316 integrators and at the same time a 10pF capacitor is added to the input to emulate the sensor capacitance. In test mode 3, the inputs are disconnected from the DDC316 integrators. Each time a new conversion begins (CONV toggles), a fixed amount of charge (approximately 1.5pC) is dumped into the integrator. Table 9. Test Mode Decoding TM[1:0] TEST MODE FUNCTION 00 Normal mode (default) 01 Test mode 1 (inputs opened) 10 Test mode 2 (inputs opened and 10pF internal capacitor connected to integrators) 11 Test mode 3 (inputs opened and 1.5pC charge dumped into the integrators during each conversion) Bit 5 Unused bit. This bit is reset to zero and must always be set to zero. Bit 4 BUFDIS—Internal Reference Buffer Disable. This bit is used to turn the internal reference buffer off, as shown in Table 10. See the Voltage Reference section for more details. Table 10. Internal Reference Buffer Disable BUFDIS Bits 3-0 16 INTERNAL REFERENCE BUFFER STATUS 0 Internal buffer enabled 1 Internal buffer disabled (default) Unused bits. These bits are reset to zero and must always be set to zero. Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 Writing and Reading of the Configuration Register Figure 2 shows the timing diagram for writing to and reading from the configuration register. Writing and reading must be done before or after CONV toggles. The data on pin DIN_CFG are latched on the falling edge of CLK. The first four bits are used as preamble; only when these bits equal '1010' are the contents of the following 16 bits loaded into the configuration register. Once the content is loaded, the shift register immediately clears so that a new configuration can be written, if needed. It is recommended to leave the DIN_CFG pin to logic '0' when not programming the register. Once the configuration register updates, it is loaded into the data shift register to be output on DOUT1. When DVALID is goes low, the configuration register is available to be read. If the data are not read back, then the register is overwritten by the conversion data on the following conversion. Data are shifted out on the falling edge of DCLK. SYSTEM AND DATA CLOCKS (CLK AND DCLK) The system clock is supplied to CLK and the data clock is supplied to DCLK. Make sure the clock signals are clean; avoid overshoot or ringing. DCLK should be held low after the data have been shifted out, or while CONV is transitioning; DCLK should not be left free-running. The integration and conversion process is fundamentally independent of the data retrieval process. Consequently, the CLK and DCLK frequencies need not be the same, although for best performance, it is highly recommended that they be derived from the same clocking source to keep their phase relationship constant. When using multiple DDC316s, pay close attention to the DCLK distribution on the printed circuit board (PCB). In particular, make sure to minimize skew in the DCLK signal because the skew can lead to timing violations in the serial interface specifications. DATA VALID (DVALID) The DVALID signal indicates that data are ready. Data retrieval may begin after DVALID goes low. This signal goes low on the rising edge of the system clock (CLK), and goes high on the first falling edge of DCLK during the data retrieval process. Data retrieval from the DDC316 can be done either by polling the DVALID signal or by counting the number of clock cycles after a transition of the CONV signal. While using the counting method, the number of clock cycles to wait depends on the mode of operation, either the low power or the high speed mode. The exact number of CLK cycles to wait for the two different modes is given in Table 3. Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 17 DDC316 SBAS370A – MARCH 2008 – REVISED APRIL 2009......................................................................................................................................................... www.ti.com READBACK WITH MULTIPLE DDC316s The serial interface supports daisy-chaining to simplify connections when using multiple DDC316s together. Figure 12 shows an example of a 64-channel system. The DIN pin is used to shift data into the DDC316s. Additional DCLK pulses must then be given during readback to ensure all the data have shifted through, as shown in Figure 13. Note that daisy-chaining is only supported in TDM output mode, and will not work when using parallel data output mode. When the daisy-chaining function is not used, connect DIN to digital ground. DCLK DVALID IN14 IN13 IN4 IN3 IN2 IN1 14 4 3 2 1 DIN 13 IN16 IN15 16 DOUT1 DDC316 15 IN2 18 IN1 IN3 19 17 DVALID DCLK IN4 IN14 IN13 30 29 DIN 20 IN16 IN15 32 DOUT1 DDC316 31 IN2 IN1 IN3 35 34 IN4 36 33 IN14 IN13 46 DIN 45 IN16 IN15 48 DOUT1 DDC316 47 IN2 IN1 50 IN3 51 49 IN4 52 DCLK DVALID DCLK IN14 IN13 62 DIN 61 IN16 IN15 64 Sensor DOUT1 DDC316 63 Data Retrieval Output DVALID Data Clock Figure 12. Daisy-Chain Configuration of a 64-Channel System DVALID DCLK tSTDIDC tHDDIDC DIN DOUT Input 64 MSB Input 64 LSB Input 63 MSB Input 3 LSB Input 2 MSB Input 2 LSB Input 1 MSB Input 1 LSB Input 64 MSB Figure 13. Daisy-Chain Readback of Four Devices (64 Channels) 18 Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 VOLTAGE REFERENCE quality capacitors with low ESR (< 1Ω) are necessary for optimum performance. High ESR capacitors will lead to oscillation of the internal buffer. Ceramic capacitors with ESR < 1Ω at 100kHz are recommended. The reference voltage is used to reset the integration capacitors before an integration cycle begins. It is also used by the ADCs when they measure the voltage stored on the integrators after an integration cycle ends. During this sampling, the external reference must supply the charge needed by the ADCs. For an integration time of 20µs, this charge translates to an average VREF current of approximately 270µA. The amount of charge needed by the ADC is independent of the integration time; therefore, increasing the integration time lowers the average current. For example, an integration time of 40µs lowers the average VREF current to 135µA. +5V VREF (4A, 6A, 6B) 0.47mF + 10mF 0.1mF DDC316 1 REF3140 2 10kW VREF_IN (4B) + 10mF 0.1mF 3 It is critical that VREF be stable during the different modes of operation (see Figure 7). The ADC measures the voltage on the integrator with respect to VREF. Since the integrator capacitors are initially reset to VREF, any drop in VREF, from the time the capacitors are reset to the time when the converter measures the integrator output, introduces an offset. It is also important that VREF be stable over longer periods of time because changes in VREF correspond directly to changes in the full-scale range. Finally, VREF should introduce as little additional noise as possible. For these reasons, it is strongly recommended that the external reference source be buffered with an operational amplifier. Figure 14. Recommended Circuit when Using the Internal VREF Buffer External VREF Buffer The internal buffer can be turned off using the control bits as explained in the Configuring the Modes section under Bit 4 and Table 10. For this option, configure the driving circuit as illustrated in Figure 15. The voltage reference is generated by a +4.096V reference. A low-pass filter to reduce noise connects the reference to an operational amplifier configured as a buffer. The VREF_IN pin must be left disconnected. The DDC316 offers two options for driving the reference voltage: through an external buffer or through an internal buffer. In both the cases, the reference voltage is generated external to the chip using an accurate reference, such as the REF3140. This amplifier used as buffer should have low noise and input/output common-mode ranges that support VREF. Even though the circuit in Figure 15 might appear to be unstable as a result of the large output capacitors, it works well for most operational amplifiers. It is not recommended that series resistance be placed in the output lead to improve stability because it can cause a drop in VREF and produce large offsets. Internal VREF Buffer The DDC316 provides an internal VREF buffer to drive the four on-chip ADCs. The reference voltage must be provided at VREF_IN (pin 4B), as shown in Figure 14. The external capacitors at the VREF pins are necessary to stabilize the internal buffer. It is recommended that these capacitors be placed as close as possible to the device under test. Also, good +5V +5V 0.1mF 0.47mF 7 2 1 REF3140 2 10kW 3 + 10mF 3 0.1mF OPA350 6 VREF (4A, 6A, 6B) + 10mF 4 0.1mF DDC316 VREF_IN (4B) Figure 15. Recommended Circuit when Using an External VREF Buffer Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 19 DDC316 SBAS370A – MARCH 2008 – REVISED APRIL 2009......................................................................................................................................................... www.ti.com RESET (RESET) LAYOUT The DDC316 can be reset asynchronously by taking the RESET input low. Make sure the reset pulse is at least two CLK cycles wide. Once the RESET signal is pulled high, the internal reset is released tRST later, after which the configuration register can be written. It is very important that RESET is glitch-free to avoid unintentional resets. Power Supplies and Grounding tCLK period CLK tRST,PUL Both AVDD and DVDD should be as quiet as possible. It is particularly important to eliminate noise from AVDD that is nonsynchronous with the DDC316 operation. For this reason, switching-supplies are not recommended. Figure 18 illustrates how to supply power to the DDC316. Each supply of the DDC316 should be bypassed with 10µF solid ceramic capacitors. It is recommended that both the analog and digital grounds (AGND and DGND) be connected to a single ground plane on the PCB. VA RESET AVDD RESETINTERNAL AGND 10mF tRST DDC316 DIN_CFG VD DVDD Figure 16. Reset Timing DGND 10mF POWER-UP SEQUENCING Figure 18. Power-Supply Connections Figure 17 shows the internal timing after the part powers up. Once the digital supply is above the threshold voltage, the internal power-on reset circuit releases the POR signal. The internal reset signal to the digital logic is released tPOR time after the PORINTERNAL, after which the configuration register can be written. CLK PORINTERNAL RESETINTERNAL tPOR DIN_CFG Shielding Analog Signal Paths As with any precision circuit, careful PCB layout ensures the best performance. It is essential to make short, direct interconnections and avoid stray wiring capacitance, particularly at the analog input pins and QGND. These analog input pins are high-impedance and extremely sensitive to extraneous noise. The QGND pin should be treated as a sensitive analog signal and connected directly to the supply ground with proper shielding. Leakage currents between the PCB traces can exceed the input bias current of the DDC316 if shielding is not implemented. Digital signals should be kept as far as possible from the analog input signals on the PCB. Figure 17. Power-Up Timing Table 11. Timing Figure 16 and Figure 17 SYMBOL tRST,PUL 20 DESCRIPTION MIN TYP MAX UNITS RESET pin low width 2 tCLK periods tRST Wait from RESET high to beginning of configuration register write 20 tCLK periods tPOR Wait from power-up to power-on reset release 40,000 tCLK periods Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 DDC316 www.ti.com......................................................................................................................................................... SBAS370A – MARCH 2008 – REVISED APRIL 2009 Revision History NOTE: Page numbers for previous revisions may be differ from page numbers in the current version. Changes from Original (March 2008) to Revision A ....................................................................................................... Page • • • • • Changed test condition for Offset Drift Stability specification ................................................................................................ 3 Changed Figure 1 ................................................................................................................................................................. 6 Changed Figure 2 ................................................................................................................................................................. 7 Added missing text................................................................................................................................................................. 9 Deleted duplicate mechanical package drawing.................................................................................................................. 20 Submit Documentation Feedback Copyright © 2008–2009, Texas Instruments Incorporated Product Folder Link(s): DDC316 21 PACKAGE OPTION ADDENDUM www.ti.com 17-Feb-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) DDC316CGXGR ACTIVE NFBGA GXG 64 1000 TBD SN/PB Level-3-240C-168 HR 0 to 70 DDC316 DDC316CGXGT ACTIVE NFBGA GXG 64 250 TBD SN/PB Level-3-240C-168 HR 0 to 70 DDC316 DDC316CZXGR ACTIVE NFBGA ZXG 64 1000 Green (RoHS & no Sb/Br) SNAGCU Level-3-260C-168 HR 0 to 70 DDC316 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 17-Feb-2017 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Feb-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing DDC316CGXGR NFBGA GXG 64 DDC316CGXGT NFBGA GXG DDC316CZXGR NFBGA ZXG SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 1000 330.0 16.4 8.3 8.3 2.25 12.0 16.0 Q1 64 250 180.0 16.4 8.3 8.3 2.25 12.0 16.0 Q1 64 1000 330.0 16.4 8.3 8.3 2.25 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Feb-2017 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DDC316CGXGR NFBGA GXG 64 1000 336.6 336.6 28.6 DDC316CGXGT NFBGA GXG 64 250 213.0 191.0 55.0 DDC316CZXGR NFBGA ZXG 64 1000 336.6 336.6 28.6 Pack Materials-Page 2 IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you (individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of this Notice. TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications (and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your noncompliance with the terms and provisions of this Notice. This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services. These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation modules, and samples (http://www.ti.com/sc/docs/sampterms.htm). Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2017, Texas Instruments Incorporated