Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) High Voltage with Flexible Termination System (HV FT-CAP) X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Overview KEMET’s High Voltage with Flexible Termination (HV FT-CAP) surface mount MLCCs in X7R dielectric combine high voltage and flexible termination technologies. Featuring a 125°C maximum operating temperature and considered “temperature stable,” these devices address the primary failure mode of MLCCs—flex cracks, which are typically the result of excessive shear stresses produced during board flexure or thermal cycling. Utilizing a conductive silver epoxy between the base metal and nickel barrier layers of KEMET’s standard termination system, flexible termination technology directs board flex stress away from the ceramic body and into the termination area, therefore mitigating flex cracks which can result in low IR or short circuit failures. Although flexible termination technology does not eliminate the potential for mechanical damage that may propagate during extreme environmental and handling conditions, it does provide superior flex performance over standard termination systems. The HV FT-CAP offers low leakage current, exhibits low ESR at high frequencies and finds conventional use as snubbers or filters in applications such as switching power supplies and lighting ballasts. Their exceptional performance at high frequencies has made them a preferred choice of design engineers worldwide. In addition to their use in power supplies, these capacitors are widely used in industries related to telecommunications, medical, military, aerospace, semiconductors and test/diagnostic equipment. Combined with the stability of an X7R dielectric and designed to accommodate all capacitance requirements, these flex-robust devices are RoHS-compliant, offer up to 5mm of flex-bend capability and exhibit a predictable change in capacitance with respect to time and voltage. Capacitance change with reference to ambient temperature is limited to ±15% from -55°C to +125°C. Benefits Applications • • • • • • • • • • -55°C to +125°C operating temperature range Superior flex performance (up to 5mm) Pb-Free and RoHS compliant EIA 0805, 1206, 1210, 1808, 1812, 1825, 2220 and 2225 case sizes DC voltage ratings of 500V, 630V, 1KV, 1.5KV, 2KV, 2.5KV and 3KV Capacitance offerings ranging from 62pF to 0.27μF Available capacitance tolerances of ±5%, ±10% or ±20%. Low ESR and ESL Non-polar device, minimizing installation concerns 100% pure matte tin-plated end metallization allowing for excellent solderability • SnPb plated end metallization option available upon request (5% min) Typical applications include switch mode power supplies (input filters, resonators, tank circuits, snubber circuits, output filters), high voltage coupling and DC blocking, lighting ballasts, voltage multiplier circuits, DC/DC converters and coupling capacitors in Ćuk converters. Markets include power supply, LCD fluorescent backlight ballasts, HID lighting, telecom equipment, industrial and medical equipment/control, LAN/WAN interface, analog and digital modems, and automotive. X7R dielectrics are not designed for AC line filtering or pulse applications. Ordering Information C Ceramic 1210 Case Size Specification/ (L" x W") Series 0805 1206 1210 1808 1812 1825 2220 2225 1 2 X X = Flexible Termination 473 K C R A C TU Capacitance Code (pF) Capacitance Tolerance Voltage Dielectric Failure Rate/ Design End Metallization1 Packaging/Grade (C-Spec)2 C = 500V B = 630V D = 1000V F = 1500V G = 2000V Z = 2500V H = 3000V R = X7R A = N/A 2 Sig. Digits + Number of Zeros J = ±5% K = ±10% M = ±20% C = 100% Matte Sn L = SnPb (5% min) Blank = Bulk TU = 7" Reel Unmarked TM = 7" Reel Marked Additional termination options may be available. Contact KEMET for details. Additional reeling or packaging options may be available. Contact KEMET for details. One WORLD One Brand One Strategy One Focus One Team © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com One KEMET C1025-1 • 9/13/2010 1 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Dimensions – Millimeters (Inches) W L B T S EIA Size Code Metric Size Code L Length W Width B Bandwidth 0805 1206 1210 1808 1812 1825 2220 2225 2012 3216 3225 4520 4532 4564 5650 5664 2.1 (.083) ± 0.30 (.012) 3.3 (.130) ± 0.40 (.016) 3.3 (.130) ± 0.40 (.016) 4.7 (.185) ± 0.50 (.020) 4.5 (.178) ± 0.40 (.016) 4.6 (.181) ± 0.40 (.016) 5.9 (.232) ± 0.75 (.030) 5.9 (.232) ± 0.75 (.030) 1.25 (.049) ± 0.20 (.008) 1.60 (.063) ± 0.20 (.008) 2.50 (.098) ± 0.20 (.008) 2.00 (.079) ± 0.20 (.008) 3.20 (.126) ± 0.30 (.012) 6.40 (.252) ± 0.40 (.016) 5.00 (.197) ± 0.40 (.016) 6.40 (.248) ± 0.40 (.016) 0.50 (0.02) ± 0.25 (.010) 0.60 (.024) ± 0.25 (.010) 0.60 (.024) ± 0.25 (.010) 0.70 (.028) ± 0.35 (.014) 0.70 (.028) ± 0.35 (.014) 0.70 (.028) ± 0.35 (.014) 0.70 (.028) ± 0.35 (.014) 0.70 (.028) ± 0.35 (.014) T Thickness Mounting Technique Solder Wave or Solder Reflow See Table 2 for Thickness Solder Reflow Only Qualification/Certification Commercial grade products are subject to internal qualification. Details regarding test methods and conditions are referenced in Table 4, Performance and Reliability. Environmental Compliance RoHS PRC ( Peoples Republic of China) compliant Electrical Parameters/Characteristics Item Parameters/Characteristics Operating Temperature Range: Capacitance Change with Reference to +25°C and 0 Vdc Applied (TCC): Aging Rate (Max % Cap Loss/Decade Hour): Dielectric Withstanding Voltage: Dissipation Factor (DF) Maximum Limit @ 25ºC: Insulation Resistance (IR) Limit @ 25°C: Insulation Resistance (IR) Limit @ 125°C: -55°C to +125°C ±15% 3.5% 150% of rated voltage for voltage rating of < 1000V 120% of rated voltage for voltage rating of ≥ 1000V 2.5% 1000 megohm microfarads or 100GΩ 100 megohm microfarads or 10GΩ To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits. Capacitance and Dissipation Factor (DF) measured under the following conditions: 1kHz and 1 Vrms if capacitance >1000pF © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 2 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Table 1A – (0805 - 1812 Case Sizes) Cap Cap Code Series Voltage Code C0805 C B C1206 D C B D C1210 F G C B D C1808 F G C B D F C1812 G Z H C B D F G Z H Voltage VDC 500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000 Cap Tolerance Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions 10 pF 100 J K M 11 pF 110 J K M 12 pF 120 J K M 13 pF 130 J K M 15 pF 150 J K M 16 pF 160 J K M 18 pF 180 J K M 20 pF 200 J K M 22 pF 220 J K M 24 pF 240 J K M 27 pF 270 J K M 30 pF 300 J K M 33 pF 330 J K M J K M 36 pF 360 39 pF 390 J K M 43 pF 430 J K M 47 pF 470 J K M 51 pF 510 J K M 56 pF 560 J K M 62 pF 620 J K M DG DG DG 68 pF 680 J K M DG DG DG 75 pF 750 J K M DG DG DG EG EG EG 82 pF 820 J K M DG DG DG EG EG EG 91 pF 910 J K M DG DG DG EG EG EG 100 pF 101 J K M DG DG DG EG EG EG 110 pF 111 J K M DG DG DG EF EF EF 120 pF 121 J K M DG DG DG EF EF EF 130 pF 131 J K M DG DG DG EF EF EF 150 pF 151 J K M DG DG DG EF EF EF 180 pF 181 J K M DG DG DG EF EF EF 220 pF 221 J K M DG DG DG EF EF EF 270 pF 271 J K M DG DG DG EF EF EF 330 pF 331 J K M DG DG DG EF EF EF 390 pF 391 J K M DG DG DG EF EF EF 470 pF 471 J K M DG DG DG EF EF EF 560 pF 561 J K M DG DG DG EF EF EF 680 pF 681 J K M DG DG DG EF EF EF 820 pF 821 J K M DG DG DG EF EF EF 1,000 pF 102 J K M DG DG DG EF EF EF 1,200 pF 122 J K M DG DG DG EF EF EF 1,500 pF 152 J K M DG DG DG EF EF EF 1,800 pF 182 J K M DG DG DG EF EF EF 2,000 pF 202 J K M DG DG DG EF EF EF 2,200 pF 222 J K M DG DG DG EF EF EF 2,700 pF 272 J K M DG DG DG EF EF EF 3,300 pF 332 J K M DG DG DG EF EF EF 3,900 pF 392 J K M DG UD UD EF EF EF 4,700 pF 472 J K M DG UD UD EF EF EF EF EF 5,600 pF J1210 K M DG XUD UD EF 473 C562 6,800 pF 682 J K M DG UD UD EG EG EG Case Capacitance EG EG 8,200 pF Ceramic 822 J Size K MSpecifi DG cation/ UD UD EG (L" Series EG(pF)EG 10,000 pF 103 J x W") K M UD UD UD EGCode 12,000 pF 123 J K M UD UD UD EG UD UD 0805 X = Flexible 2 Sig. Digits + 15,000 pF 153 J K M UD UD UD EG UD UD 1206 Termination Number of Zeros 18,000 pF 183 J K M UD UD UD UD UD UD 1210K M J 22,000 pF 223 UD UD UD UD 27,000 pF 273 J1808K M UD UD UD UD 1812 1825 Cap Voltage 2220 Code C B D Code 2225 Series C0805 EG EG EG EG EF EF EF EF EF EF EF EF EF EF EF EF EF EF EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG EG LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LB LA LA LA LA LB LB LB FL FL FL FL FL LA LA LA LA LB LB LB FL FL FL FL FL LA LA LA LA LB LB LB GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LB GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LB GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LC GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LC GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LC GK GK GK GK GK FL FL FL FL FL LA LA LA LA LB LB LC GH GH GH GH GH FL FL FL FL FL LA LA LA LA LB LB LC GH GH GH GH GH EG FL FL FL FL FL LA LA LA LA LB LC LC GH GH GH GH GH EG FL FL FL FL FL LA LA LA LA LB LC LC GH GH GH GH GH EG FL FL FL FL FL LA LA LA LA LB LC LC GH GH GH GH GH EG FL FL FL FL FM LB LB LB LB LC GH GH GH GH GH EG FL FL FL FL FM LA LA LA LB LC GH GH GH GH GH EG FL FL FL FL FM LA LA LA LB LC GH GH GH GH GH EG FL FL FL FL FM LA LA LA LB LC GH GH GH GH GH GH GH GH GH GH EG FL FL FL FL FM LA LA LA LB LC FL FL FL FL FM LA LA LA LB LC GH GH GH GH GK FL FL FL FL FM LA LA LA LB GH GH GH GH GK FL FL FL FL FK LA LA LA LB GH GH GH GH GK FL FL FL FL FK LA LA LA LB GH GH GH GH GH GH GHTUGK K FL FL CFL FM R LA LB ALB LC C FL FL FL FM LA LB LB LC GH GH GH GK Rate/LC Capacitance Packaging/Grade FL FLVoltage FL FK Dielectric LA Failure LB LB End Metallization1 GH GH GH GK2 Tolerance FL FL FL FK LA LBDesign LB LC GH GH (C-Spec) GH GK FL FK LA LC LC GK GK GK J = ±5%FL FL C = 500V R = X7R A = N/A C = 100% Matte SnGH Blank = Bulk FL FL FL LA LC LC GH GK GK K = ±10% B = 630V L = SnPb (5% min) TU = 7" Reel FL FL FL LA UD UD GH GK GK M = ±20% D = 1000V Unmarked FL FM FM LA UD UD GH GK GK F = 1500V FM FK FK LA UD UD GH TM = 7" Reel Marked G = 2000V Z = 2500V BH = 3000V D F GK GK GK GK GK GK GK GK GK GK GK GK GK GK GK GK GK GK GK GK GK GK GK GK Voltage VDC 500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000 Cap C B D C1206 F G C C1210 G C B D F C1808 G Z H C B D F G Z H C1812 UD = Under Developement © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Roll Over for Order Info. C1025-1 • 9/13/2010 3 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Table 1A con't – (0805 - 1812 Case Sizes) Cap Cap Code 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.10 uF 0.12 uF 0.15 uF 0.18 uF 0.22 uF 0.27 uF 0.33 uF 333 393 473 563 683 823 104 124 154 184 224 274 334 Series C0805 Voltage Code C B C1206 D C B D C1210 F G C B D C1808 F G C B D F C1812 G Z H C B D F G Z H Voltage VDC 500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000 Cap Tolerance J J J J J J J J J J J K K K K K K K K K K K M M M M M M M M M M M Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions UD UD UD UD UD UD UD UD UD UD UD UD UD UD FM FK FK UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD UD LC LC LC LC UD UD UD UD UD UD UD GH GH GH GH GK GK GK Voltage VDC 500 630 1000 500 630 1000 1500 2000 500 630 1000 1500 2000 500 630 1000 1500 2000 2500 3000 500 630 1000 1500 2000 2500 3000 Cap Cap Voltage Code C Code Series B D C B C0805 D F G C B C1206 D F G C B D C1210 F G Z H C B D F C1808 G Z H C1812 Table 1B – (1825 - 2225 Case Sizes) Cap Cap Code Series C1825 Voltage Code C B Voltage VDC 500 630 Cap Tolerance Cap 1812 Voltage VDC 1825 Voltage Code 2220 2225Series F G Z H 1000 1500 2000 2500 3000 C B 500 630 D F C2225 G Z H 1000 1500 2000 2500 3000 C B 500 630 D F G Z H 1000 1500 2000 2500 3000 Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions 100 pF 101 J K M 110 pF 111 J K M 120 pF 121 J K M 130 pF 131 J K M 150 pF 151 J K M 180 pF 181 J K M 220 pF 221 J K M 270 pF 271 J K M 330 pF 331 J K M HG 390 pF 391 J K M HG K M HG 470 pF 471 J 560 pF 561 J K M HG 680 pF 681 J K M HG 820 pF 821 J K M HG 1,000 pF 102 J K M HG 1,200 pF 122 J K M HG 1,500 pF 152 J K M HG 1,800 pF 182 J K M HE C 1210 X 2,000 pF 202 J K M HE 2,200 pF 222 Case J SizeK Specifi M cation/ HE 2,700 pF Ceramic 272 M HE (L" xJ W") K Series 3,300 pF 332 J K M HE 0805 = Flexible 3,900 pF 392 J K XM HE 1206 4,700 pF 472 J K Termination M HE 5,600 pF 562 J K M HE 1210 6,800 pF 682 J K M HE 1808 Cap Code D C2220 HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HG HE HE HE 473 HE HE HE HE Capacitance HE HE HE HE Code (pF)HE HE HE HE HE2 Sig. HEDigitsHE+ Number HE HE of Zeros HE HE HE HE HE HE HE 500 630 C B HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HG HG HG JP JP JP HE HG HG JP JP JP C RJE HE KHG HG JE JE HE HG HG JE JE JE Capacitance HG Voltage JE JE Dielectric JE HE HG Tolerance HE HG HG JE JE JE C = 500V X7R HEJ = ±5% JE JE R = JE B = 630V HEK = ±10% JE JE JE HEM = ±20% D = 1000V JE JE JE HE JE JE JE F = 1500V 2000V630 1000 1500 2000 2500 3000G = 500 D F C1825 G Z H Z = 2500V C B H = 3000V JP JP JP JP JP JP JP JP JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF JP JP JP JP KF KF KF KF KF AJE JP JP C KF KF KF KF TU KF JE JE JP KF KF KF KF KF FailureJERate/JP Packaging/Grade 1 Metallization JE JE JP EndJP KE KE KE KE 2KE Design (C-Spec) JE JE JP JP KE KE KE KE KE N/A JPC = 100% JE A = JE JP Matte KE Sn KE Blank KE = Bulk KE KE L = SnPb (5% JE JP KE min)KE TUKE= 7" Reel KE KE JE JP KE KE KE Unmarked KE KE JE JP KE KE TM KE= 7" Reel KE Marked KF 1000 1500 2000 2500 3000 D F G C2220 Z H 500 630 C B KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF KF 1000 1500 2000 2500 3000 D F G Z H C2225 UD = Under Developement. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Roll Over for Order Info. C1025-1 • 9/13/2010 4 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Table 1B con't – (1825 - 2225 Case Sizes) Cap Cap Code 8,200 pF 10,000 pF 12,000 pF 15,000 pF 18,000 pF 22,000 pF 27,000 pF 33,000 pF 39,000 pF 47,000 pF 56,000 pF 68,000 pF 82,000 pF 0.10 uF 0.12 uF 0.15 uF 0.18 uF 0.22 uF 0.27 uF 0.33 uF 0.39 uF 0.47 uF 0.56 uF 0.68 uF 0.82 uF 1.0 uF 1.2 uF 1.5 uF 1.8 uF 2.2 uF 2.7 uF 3.3 uF 822 103 123 153 183 223 273 333 393 473 563 683 823 104 124 154 184 224 274 334 394 474 564 684 824 105 125 155 185 225 275 335 Cap Cap Code Series C1825 Voltage Code C B Voltage VDC 500 630 HE HE HE HE HE HE HE HE HE HE HE HG HG HG HG HG HG HG HE HE HE HE HE HG HG HG HG HG Voltage VDC 500 630 Voltage Code C B Cap Tolerance C Ceramic J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K K D Z H C B 500 630 D F C2225 G Z H 1000 1500 2000 2500 3000 C B 500 630 D F G Z H 1000 1500 2000 2500 3000 Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M M HE HE HE HE HE HG HG HG HG HG HE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JE JP JP JP JE JE JP JP JP JP JP JP JP JP 1000 1500 2000 2500 3000 500 630 C B D HE HE HG HG HG HG HG F G Z H JE JE JP JP JP JP JP JP JP JP JP KE KE KE KE KE KE KE KE KE KE KE KE KE KE KE KF KF KF KF KE KE KE KE KE KF KF KF KF KF KF KF KF 1000 1500 2000 2500 3000 500 630 X X = Flexible Termination JE JE JP JP JP JP JP JP C B D C1825 Case Size Specification/ (L" x W") Series 0805 1206 1210 1808 1812 1825 2220 2225 G 1000 1500 2000 2500 3000 Series 1210 F C2220 F G Z H C2220 KE KE KE KE KE KF KF KF KF KF KF KF KF KE KE KE KE KE KF KF KF KF KF KF KF KF 1000 1500 2000 2500 3000 D F G 473 K C R A C TU Capacitance Code (pF) Capacitance Tolerance Voltage Dielectric Failure Rate/ Design End Metallization1 Packaging/Grade (C-Spec)2 C = 500V B = 630V D = 1000V F = 1500V G = 2000V Z = 2500V H = 3000V R = X7R A = N/A 2 Sig. Digits + Number of Zeros J = ±5% K = ±10% M = ±20% © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Roll Over for Order Info. Z H C2225 C = 100% Matte Sn L = SnPb (5% min) Blank = Bulk TU = 7" Reel Unmarked TM = 7" Reel Marked C1025-1 • 9/13/2010 5 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Table 2 – Chip Thickness / Packaging Quantities Thickness Code AA AB BB CB CC CD DC DD DL DE DF DG DH EB EK EC EN ED EE EF EM EG EH EJ FB FC FD FE FF FG FL FO FH FP FM FJ FN FT FK FR FS PA MA NA NA LD LA LB LC GB GC GD GE GH GF GG GK GJ GN GL GM GO HB HC HD HE HF HG JB JC JD JE JF JP JG JH JO KB KC KD KE KF Chip Size 01005 0201 0402 0603 0603 0603 0805 0805 0805 0805 0805 0805 0805 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1210 1220 1632 1706 1706 1808 1808 1808 1808 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1812 1825 1825 1825 1825 1825 1825 2220 2220 2220 2220 2220 2220 2220 2220 2220 2225 2225 2225 2225 2225 Thickness ± Range (mm) 0.20 ± 0.02 0.30 ± 0.03 0.50 ± 0.05 0.80 ± 0.07 0.80 ± 0.10 0.80 ± 0.15 0.78 ± 0.10 0.90 ± 0.10 0.95 ± 0.10 1.00 ± 0.10 1.10 ± 0.10 1.25 ± 0.15 1.25 ± 0.20 0.78 ± 0.10 0.80 ± 0.10 0.90 ± 0.10 0.95 ± 0.10 1.00 ± 0.10 1.10 ± 0.10 1.20 ± 0.15 1.25 ± 0.15 1.60 ± 0.15 1.60 ± 0.20 1.70 ± 0.20 0.78 ± 0.10 0.90 ± 0.10 0.95 ± 0.10 1.00 ± 0.10 1.10 ± 0.10 1.25 ± 0.15 1.40 ± 0.15 1.50 ± 0.20 1.55 ± 0.15 1.60 ± 0.20 1.70 ± 0.20 1.85 ± 0.20 1.85 ± 0.20 1.90 ± 0.20 2.10 ± 0.20 2.25 ± 0.20 2.50 ± 0.20 0.80 ± 0.10 0.80 ± 0.10 0.90 ± 0.10 0.90 ± 0.10 0.90 ± 0.10 1.40 ± 0.15 1.60 ± 0.15 2.00 ± 0.15 1.00 ± 0.10 1.10 ± 0.10 1.25 ± 0.15 1.30 ± 0.10 1.40 ± 0.15 1.50 ± 0.10 1.55 ± 0.10 1.60 ± 0.20 1.70 ± 0.15 1.70 ± 0.20 1.90 ± 0.20 2.00 ± 0.20 2.50 ± 0.20 1.10 ± 0.15 1.15 ± 0.15 1.30 ± 0.15 1.40 ± 0.15 1.50 ± 0.15 1.60 ± 0.20 1.00 ± 0.15 1.10 ± 0.15 1.30 ± 0.15 1.40 ± 0.15 1.50 ± 0.15 1.60 ± 0.20 1.70 ± 0.15 1.80 ± 0.15 2.40 ± 0.15 1.00 ± 0.15 1.10 ± 0.15 1.30 ± 0.15 1.40 ± 0.15 1.60 ± 0.20 Qty per Reel 7" Plastic 4000 2500 2500 2500 2500 4000 2000 4000 4000 2500 2500 2500 2500 2000 2000 2000 4000 4000 4000 2500 2500 2500 2000 2000 2000 2000 2000 2000 2000 1500 2000 2000 1000 4000 4000 4000 4000 2500 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 500 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 500 1000 1000 1000 1000 1000 Qty per Reel 13" Plastic 10000 10000 10000 10000 10000 10000 8000 10000 10000 10000 10000 10000 10000 8000 8000 8000 10000 10000 10000 10000 10000 10000 8000 8000 8000 8000 8000 8000 8000 4000 8000 8000 4000 10000 10000 10000 10000 10000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 2000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 4000 2000 4000 4000 4000 4000 4000 Qty per Reel 7" Paper 15000 15000 10000 4000 4000 4000 4000 4000 4000 Qty per Reel 13" Paper Qty per Bulk Cassette 50000 10000 10000 10000 10000 10000 50000 15000 10000 Package Quantity Based on Finished Chip Thickness Specifications © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 6 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Soldering Process Recommended Soldering Technique: • Solder wave or solder reflow for case sizes 1206 and less • Case sizes 1210 and greater are limited to solder reflow only Recommended Soldering Profile • KEMET recommends following the guidelines outlined in IPC/JEDEC J-STD-020D.1 Table 3 – Chip Capacitor Land Pattern Design Recommendations per IPC-7351 (mm) EIA Size Code Metric Size Code Density Level A: Maximum (Most) Land Protrusion (mm) C Y X V1 Density Level B: Median (Nominal) Land Protrusion (mm) V2 C Y X V1 Density Level C: Minimum (Least) Land Protrusion (mm) V2 C Y X V1 V2 0603 1608 0.85 1.25 1.10 4.00 2.10 0.75 1.05 1.00 3.10 1.50 0.65 0.85 0.90 2.40 1.20 0805 2012 1.05 1.45 1.55 4.60 2.60 0.95 1.25 1.45 3.70 2.00 0.85 1.05 1.35 3.00 1.70 1206 3216 1.60 1.65 1.90 5.90 2.90 1.50 1.45 1.80 5.00 2.30 1.40 1.25 1.70 4.30 2.00 1210 3225 1.60 1.65 2.80 5.90 3.80 1.50 1.45 2.70 5.00 3.20 1.40 1.25 2.60 4.30 2.90 1808 4520 2.25 1.85 2.30 7.40 3.30 2.15 1.65 2.20 6.50 2.70 2.05 1.45 2.10 5.80 2.40 1812 4532 2.10 1.80 3.60 7.00 4.60 2.00 1.60 3.50 6.10 4.00 1.90 1.40 3.40 5.40 3.70 1825 4564 2.15 1.80 6.90 7.10 7.90 2.05 1.60 6.80 6.20 7.30 1.95 1.40 6.70 5.50 7.00 2220 5650 2.85 2.10 5.50 8.80 6.50 2.75 1.90 5.40 7.90 5.90 2.65 1.70 5.30 7.20 5.60 2225 5664 2.85 2.10 6.90 8.80 7.90 2.75 1.90 6.80 7.90 7.30 2.65 1.70 6.70 7.20 7.00 Density Level A: For low-density Product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. KEMET only recommends wave soldering of EIA 0603, 0805 and 1206 case sizes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC standard 7351 (IPC-7351). © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 7 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Table 4 – Performance & Reliability: Test Methods and Conditions Stress Reference Ripple Current "Heat Generation ∆T : 20ºC max." Test or Inspection Method Terminal Strength JIS-C-6429 Appendix 1, Note: Force of 1.8kg for 60 seconds. Board Flex JIS-C-6429 Appendix 2, Note: 2mm (min) for all except 3mm for C0G. "Reflow solder the capacitor onto a PC board and apply voltage with 10kHz~1Mhz sine curve. (Ripple voltage must be < rated voltage)" Magnification 50X. Conditions: Solderability J-STD-002 a) Method B, 4 hrs @ 155°C, dry heat @ 235°C b) Method B @ 215°C category 3 c) Method D, category 3 @ 260°C Temperature Cycling JESD22 Method JA-104 1000 Cycles (-55°C to +125°C), Measurement at 24 hrs. +/- 2 hrs after test conclusion. Load Humidity: 1000 hours 85°C/85%RH and 300VDC Max. Add 100K ohm resistor. Measurement at 24 hrs. +/- 2 hrs after test conclusion. Low Volt Humidity: 1000 hours 85C°/85%RH and 1.5V. Add 100K ohm resistor. Measurement at 24 hrs. +/- 2 hrs after test conclusion. t = 24 hours/cycle. Steps 7a & 7b not required. Unpowered. Measurement at 24 hrs. +/- 2 hrs after test conclusion. -55°C/+125°C. Note: Number of cycles required-300, Maximum transfer time-20 seconds, Dwell time-15 minutes. Air-Air. Biased Humidity MIL-STD-202 Method 103 Moisture Resistance MIL-STD-202 Method 106 Thermal Shock MIL-STD-202 Method 107 High Temperature Life MIL-STD-202 Method 108 1000 hours at 125°C (85°C for X5R, Z5U and Y5V) with rated voltage applied. Storage Life MIL-STD-202 Method 108 150°C, 0VDC, for 1000 Hours. Mechanical Shock MIL-STD-202 Method 213 Figure 1 of Method 213, Condition F. Resistance to Solvents MIL-STD-202 Method 215 Add Aqueous wash chemical - OKEM Clean or equivalent. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 8 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Tape & Reel Packaging Information KEMET offers Multilayer Ceramic Chip Capacitors packaged in 8mm, 12mm and 16mm tape on 7" and 13" reels in accordance with EIA standard 481. This packaging system is compatible with all tape fed automatic pick and place systems. See Table 2 for details on reeling quantities for commercial chips. Bar Code Label Anti-Static Reel ® Embossed Plastic* or Punched Paper Carrier. T ME KE Chip and KPS Orientation in Pocket (except 1825 Commercial, and 1825 & 2225 Military) Sprocket Holes Embossment or Punched Cavity 8mm, 12mm or 16mm Carrier Tape 178mm (7.00") or 330mm (13.00") Anti-Static Cover Tape (.10mm (.004") Max Thickness) *EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only. Table 5 – Carrier Tape Configuration (mm) EIA Case Size Tape size (W)* Pitch (P1)* 01005 - 0402 8 2 0603 - 1210 8 4 1805 - 1808 12 4 ≥ 1812 12 8 KPS 1210 12 8 KPS 1812 & 2220 16 12 Array 0508 & 0612 8 4 *Refer to Figure 1 for W and P1 carrier tape reference locations. *Refer to Table 6 for tolerance specifications. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 9 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Figure 1 – Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ØDo Po [10 pitches cumulative tolerance on tape ±0.2 mm] E1 Ao F Ko B1 E2 Bo S1 W P1 T1 Center Lines of Cavity ØD 1 Cover Tape B 1 is for tape feeder reference only, including draft concentric about B o. Embossment For cavity size, see Note 1 Table 6 User Direction of Unreeling Table 6 – Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size D0 8mm 12mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) 16mm D1 Min. Note 1 1.0 (0.039) 1.5 (0.059) E1 P0 P2 1.75 ± 0.10 (0.069 ± 0.004) 4.0 ± 0.10 (0.157 ± 0.004) 2.0 ± 0.05 (0.079 ± 0.002) R Ref. Note 2 25.0 (0.984) 30 (1.181) S1 Min. Note 3 T Max. T1 Max. 0.600 (0.024) 0.600 (0.024) 0.100 (0.004) Variable Dimensions — Millimeters (Inches) Tape Size Pitch 8mm Single (4mm) 12mm Single (4mm) & Double (8mm) 16mm Triple (12mm) B1 Max. Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Min. F P1 T2 Max W Max A0,B0 & K0 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) 3.5 ± 0.05 (0.138 ± 0.002) 5.5 ± 0.05 (0.217 ± 0.002) 5.5 ± 0.05 (0.217 ± 0.002) 4.0 ± 0.10 (0.157 ± 0.004) 8.0 ± 0.10 (0.315 ± 0.004) 8.0 ± 0.10 (0.315 ± 0.004) 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape with or without components shall pass around R without damage (see Figure 5). 3. If S1<1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Document 481 paragraph 4.3 (b)). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20° maximum for 8 and 12mm tapes and 10° maximum for 16mm tapes (see Figure 3). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8mm and 12mm wide tape and to 1.0mm maximum for 16mm tape (see Figure 4). (e) for KPS Series product A0 and B0 are measured on a plane 0.3mm above the bottom of the pocket. (f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 10 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Figure 2 – Punched (Paper) Carrier Tape Dimensions P2 T Po ØDo [10 pitches cumulative tolerance on tape ±0.2 mm] A0 F P1 T1 T1 Top Cover Tape W E2 B0 Bottom Cover Tape E1 G Cavity Size, See Note 1, Table 7 Center Lines of Cavity Bottom Cover Tape User Direction of Unreeling Table 7 – Punched (Paper) Carrier Tape Dimensions Metric will govern Constant Dimensions — Millimeters (Inches) Tape Size D0 E1 P0 P2 T1Max G Min 8mm 1.5 +0.10-0.0 (0.059 +0.004, -0.0) 1.75 ±0.10 (0.069 ±0.004) 4.0 ±0.10 (0.157 ±0.004) 2.0 ±0.05 (0.079 ±0.002) 0.10 (.004) Max. 0.75 (.030) R Ref. Note 2 25 (.984) T Max W Max A0 B 0 1.1 (0.098) 8.3 (0.327) 8.3 (0.327) Variable Dimensions — Millimeters (Inches) Tape Size Pitch 8mm Half (2mm) 8mm Single (4mm) E2 Min 6.25 (0.246) F 3.5 ± 0.05 (0.138 ± 0.002) P1 2.0 ± 0.05 (0.079 ± 0.002) 4.0 ± 0.10 (0.157 ± 0.004) Note 5 1. The cavity defined by A0, B0 and T shall surround the component with sufficient clearance that: a) the component does not protrude beyond either surface of the carrier tape. b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4). e) see Addendum in EIA Document 481 for standards relating to more precise taping requirements. 2. The tape with or without components shall pass around R without damage (see Figure 5). © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 11 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 Kg Minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8mm 12mm & 16mm 0.1 Newton to 1.0 Newton (10g to 100g) 0.1 Newton to 1.3 Newton (10g to 130g) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180° from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300±10 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA-556 and EIA-624. Figure 3 – Maximum Component Rotation ° T Maximum Component Rotation Top View Maximum Component Rotation Side View Typical Pocket Centerline Tape Width (mm) 8,12 16-200 Bo Maximum Rotation ( 20 10 ° T) Typical Component Centerline Ao ° s Tape Width (mm) 8,12 16-56 72-200 Maximum Rotation ( 20 10 5 ° S) Figure 4 – Maximum Lateral Movement 8mm & 12mm Tape 16mm Tape 0.5 mm maximum 0.5 mm maximum 1.0 mm maximum 1.0 mm maximum Figure 5 – Bending Radius Embossed Carrier R Punched Carrier Bending Radius R © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 12 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Figure 6 – Reel Dimensions Full Radius, See Note W3 (Includes Access Hole at Slot Location (Ø 40 mm min.) flange distortion at outer edge) W2 (Measured at hub) D A (See Note) N C (Arbor hole diameter) B (see Note) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm min. width x 10.0 mm min. depth Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 8 – Reel Dimensions Metric Dimensions Will Govern Constant Dimensions — Millimeters (Inches) Tape Size A B Min C D Min 8mm 178 ± 0.20 (7.008 ± 0.008) or 330 ± 0.20 (13.000 ± 0.008) 1.5 (0.059) 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) 20.2 (0.795) 12mm 16mm Variable Dimensions — Millimeters (Inches) Tape Size N Min 8mm 12mm 16mm 50 (1.969) W1 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com W2 Max 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) W3 Shall accommodate tape width without interference C1025-1 • 9/13/2010 13 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Figure 7 – Tape Leader & Trailer Dimensions Embossed Carrier Carrier Tape Punched Carrier 8 mm & 12 mm only Round Sprocket Holes END START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm minimum, Components 100 mm Min. Leader 400 mm Minimum, Top Cover Tape Figure 8 – Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm maximum, either direction Straight Edge 250 mm © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 14 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Figure 9 – Bulk Cassette Packaging (Ceramic Chips Only) Meets Dimensional Requirements IEC-286 and EIAJ 7201 6 8 ± 0.1 8 8 ± 0.1 12.0 ± 0.1 Unit mm *Reference 19.0* 36 ± 00.2 31.5 ± 0.2 0 53 3* 10* 1.5 ± 2.0 ± 3.0 ± 0.1 0 0 0.1 0.2 0 5 0* 110 ± 0.7 Table 9 – Capacitor Dimensions for Bulk Cassette Cassette Packaging – Millimeters EIA Size Metric Size L Length Code Code W Width B Bandwidth S Separation minimum T Thickness Number of Pcs/Cassette 0402 1005 1.0 ± 0.05 0.5 ± 0.05 0.2 to 0.4 0.3 0.5 ± .05 50,000 0603 1608 1.6 ± 0.07 0.8 ± 0.07 0.2 to 0.5 0.7 0.8 ± .07 15,000 Table 10 – Capacitor Marking Laser marking is available as an extra-cost option for most KEMET ceramic chips. Such marking is two sided, and includes a K to identify KEMET, followed by two characters (per EIA-198) to identify the capacitance value. Note that marking is not available for any Y5V chip. ln addition, the 0603 marking option is limited to the K only. (Marking Optional – Not Available for 0402 Size) Numeral Alpha Character A B C D E F G H J K L M N P Q R S T U V W X Y Z a b d e f m n t y Capacitance (pF) For Various Numeral Identifiers 9 0.1 0.11 0.12 0.13 0.15 0.16 0.18 0.2 0.22 0.24 0.27 0.3 0.33 0.36 0.39 0.43 0.47 0.51 0.56 0.62 0.68 0.75 0.82 0.91 0.25 0.35 0.4 0.45 0.5 0.6 0.7 0.8 0.9 0 1 1.1 1.2 1.3 1.5 1.6 1.8 2 2.2 2.4 2.7 3 3.3 3.6 3.9 4.3 4.7 5.1 5.6 6.2 6.8 7.5 8.2 9.1 2.5 3.5 4 4.5 5 6 7 8 9 1 10 11 12 13 15 16 18 20 22 24 27 30 33 36 39 43 47 51 56 62 68 75 82 91 25 35 40 45 50 60 70 80 90 2 100 110 120 130 150 160 180 200 220 240 270 300 330 360 390 430 470 510 560 620 680 750 820 910 250 350 400 450 500 600 700 800 900 3 1000 1100 1200 1300 1500 1600 1800 2000 2200 2400 2700 3000 3300 3600 3900 4300 4700 5100 5600 6200 6800 7500 8200 9100 2500 3500 4000 4500 5000 6000 7000 8000 9000 4 10000 11000 12000 13000 15000 16000 18000 20000 22000 24000 27000 30000 33000 36000 39000 43000 47000 51000 56000 62000 68000 75000 82000 91000 25000 35000 40000 45000 50000 60000 70000 80000 90000 5 100000 110000 120000 130000 150000 160000 180000 200000 220000 240000 270000 300000 330000 360000 390000 430000 470000 510000 560000 620000 680000 750000 820000 910000 250000 350000 400000 450000 500000 600000 700000 800000 900000 6 1000000 1100000 1200000 1300000 1500000 1600000 1800000 2000000 2200000 2400000 2700000 3000000 3300000 3600000 3900000 4300000 4700000 5100000 5600000 6200000 6800000 7500000 8200000 9100000 2500000 3500000 4000000 4500000 5000000 6000000 7000000 8000000 9000000 7 10000000 11000000 12000000 13000000 15000000 16000000 18000000 20000000 22000000 24000000 27000000 30000000 33000000 36000000 39000000 43000000 47000000 51000000 56000000 62000000 68000000 75000000 82000000 91000000 25000000 35000000 40000000 45000000 50000000 60000000 70000000 80000000 90000000 © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com Example shown is 1,000 pF capacitor C1025-1 • 9/13/2010 15 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) Other KEMET Resources Tools Resource Location Configure A Part: CapEdge http://capacitoredge.kemet.com SPICE & FIT Software http://www.kemet.com/spice Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask Product Information Resource Location Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Product Request Resource Location Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Contact Resource Location Website Contact Us Investor Relations www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir Call Us 1-877-MyKEMET Twitter http://twitter.com/kemetcapacitors Disclaimer All product specifications, statements, information and data (collectively, the “Information”) are subject to change without notice. All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute – and we specifically disclaim – any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 16 SMD MLCCs – High Voltage with Flexible Termination System (HV FT-CAP), X7R Dielectric, 500VDC-3000VDC (Commercial Grade) KEMET Corporation World Headquarters P.O. Box 5928 Greenville, SC 29606 2835 KEMET Way Simpsonville, SC 29681 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 North America Corporate Offices 101 NE Third Avenue Tower 101, Suite 1700 Fort Lauderdale, FL 33301 Tel: 954-766-2800 Fax: 954-766-2805 Southeast 801 International Parkway, Suite 5070 Lake Mary, FL 32746 Tel: 407-855-8886 Northeast 340-X Fordham Road Wilmington, MA 01887 Tel: 978-658-1663 Fax: 978-658-1790 Central 1900 North Roselle Road, Suite 405 Schaumburg, IL 60195 Tel: 847-882-3590 Fax: 847-882-3046 Europe Southern Europe 15bis chemin des Mines, 4th floor 1202 Geneva Switzerland Tel: 41-22-715-0100 Fax: 41-22-715-0170 Zac Paris Rive Gauche 118-122 avenue de France 75013 Paris France Tel: 33-1-4646-1009 Fax: 33-1-4646-1599 Via San Lorenzo 19 Sasso Marconi, BO 40037 Italy Tel: 39-051-939111 Fax: 39-051-840684 Viale Milanofiori 1 Palazzo E1 20090 Assago Milano Italy Tel: 39-02-57518176 Fax: 39-02-57512093 Central Europe Hermann-Koehl-Str. 2 Landsberg am Lech 86899 Germany Tel: 49-8191-3350800 Fax: 49-8191-3350990 West 1551 McCarthy Boulevard, Suite 117 Milpitas, CA 95035 Tel: 408-433-9946 Fax: 408-433-9946 Ruhrallee 9 Dortmund 44139 Germany Tel: 49-2307-3619672 Fax: 49-2307-961527 Mexico Northern Europe Tezozomoc No. 47 Col. Ciudad del Sol Zapopan, Jalisco C.P. 45050 Mexico Tel: 52-33-3123-2141 Fax: 52-33-3123-2144 Unit 1, Ducketts Wharf South Street Bishops Stortford Hertfordshire CM23 3AL United Kingdom Tel: 44-1279-757201 Fax: 44-1279-465237 20-21 Cumberland Drive Granby Industrial Estate Weymouth, Dorset DT4 9TE United Kingdom Tel: 44-1305-830747 Fax: 44-1305-760670 Room 305, Floor 3, #142 Sec. 4, Chung Hsiao East Road Taipei 106 Taiwan ROC Tel: 886-2-27528585 Fax: 886-2-27213129 Thörnblads Väg 6 Färjestaden 386 90 Sweden Tel: 46-485-563934 Fax: 46-485-563938 Southeast Asia Stella Business Park Lars Sonckin kaari 16 Espoo 02600 Finland Tel: 358-9-5406-5000 Fax: 358-9-5406-5010 Asia Northeast Asia 30 Canton Road, Room 1512 Silvercord Tower II Tsimshatshui, Kowloon Hong Kong Tel: 852-2305-1168 Fax: 852-2759-0345 73 Bukit Timah Road #05-01 Rex House 229832 Singapore Tel: 65-6586-1900 Fax: 65-6586-1901 1-5-20 Krystal Point 2 Lebuh Bukit Kecil 6 11900 Bayan Baru Penang Malaysia Tel: 6- 04-6430200 Fax: 6 -04-6444220 Office No. 605, 6th Floor Barton Centre M.G. Road Bangalore 560 001 India Tel: 91-80-653-76817 Fax: 91-80-2532-0160 Room 1411, 14/F New China Insurance Edifice Mintian Road, CBD Futian District Shenzhen 518001 China Tel: 1-867-55-25181306 Fax: 1-867-55-25181307 Floor 17, Tower B, Ping An IFC No.1-3 Xin Yuan South Road Chao Yang District Beijing 100027 China Tel: 86-10-5829-1711 Fax: 86-10-5829-1963 Room 2602, Grand Gateway Tower 1 No.1 Hong Qiao Road Shanghai 200030 China Tel: 86-21-6447-0707 Fax: 86-21-6447-0070 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1025-1 • 9/13/2010 17