SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS TM AIchip MZR - Series ・Downsizing and Lower ESR, 2,000hours at 105℃ ・Rated voltage range : 6.3 to 50V, Nominal capacitance range : 100 to 2,200μF ・Solvent resistant type(see PRECAUTIONS AND GUIDELINES) ・Vibration resistance structure ・RoHS Compliant ・AEC-Q200 compliant : Please contact Chemi-Con for more details, test data, information. Low ESR, 105℃ MZR Downsized MZJ P98 ◆SPECIFICATIONS Items Category Temperature Range Rated Voltage Range Capacitance Tolerance Leakage Current Dissipation Factor (tanδ) Low Temperature Characteristics (Max. Impedance Ratio) Endurance Shelf Life Surge Voltage Test Characteristics -55 to +105℃ 6.3 to 50Vdc (at 20℃, 120Hz) ±20% (M) I=0.01CV or 3μA, whichever is greater. Where, I : Max. leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V) (at 20℃ after 2 minutes) Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V (at 20℃, 120Hz) tanδ(Max.) 0.26 0.19 0.16 0.14 0.12 0.10 Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V (at 120Hz) Z(-25℃)/Z(+20℃) 2 2 2 2 2 2 Z(-40℃)/Z(+20℃) 3 3 3 3 3 3 Z(-55℃)/Z(+20℃) 4 4 4 3 3 3 The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours at 105℃. Capacitance change ≦±30% of the initial value D.F. (tanδ) ≦200% of the initial specified value Leakage current ≦The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4. Capacitance change ≦±30% of the initial value D.F. (tanδ) ≦200% of the initial specified value Leakage current ≦The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specified surge voltage for 30±5 seconds through a protective resistor (as required for RC=0.1±0.05sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35℃. Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V 7.2V 12V 18V 29V 40V 58V Surge voltage (Vdc) Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦200% of the initial specified value Leakage current ≦The initial specified value (Caution) Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specific conditions.It does not imply long-term use at all. ◆DIMENSIONS [mm] ● Terminal ● Terminal ● Size ● Size B±0.2 φD±0.5 P C±0.2 0.3max. L±0.3 (Note) D 6.3 8 10 C B A L 7.7 6.6 6.6 7.2 10.0 8.3 8.3 9.0 10.0 10.3 10.3 11.0 W 0.5 to 0.8 0.7 to 1.1 0.7 to 1.1 P 1.9 3.1 4.5 A±0.2 L±0.5 A±0.2 F80 HA0 JA0 W 0.3max. Vent for JA0 W B±0.2 φD±0.5 Vent for JA0 Code : G(Vibration resistant structure) code : HA0 and JA0 Size code P C±0.2 Code : A code : F80 to JA0 Note : L±0.5 for HA0 and JA0 : Dummy terminals ◆MARKING EX) 35V330µF 3Q 330 VZR ● Rated voltage symbol Rated voltage (Vdc) Symbol 6.3 j 10 A 16 C 25 E 35 V 50 H Applying voltage over the rated voltages causes the capacitors to have short lifetime. Besides, applying voltage over the specified surge voltages may cause to have short circuit failure. A protection circuit should be used if applied voltage will exceed the rated voltages. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 96 CAT. No. E1001Q SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS MZRSeries TM AIchip Low ESR, 105℃ - ◆PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 E MZ R AAA A DA AAA M AAA G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 220µF:221, 470µF:471) Taping code Terminal code (A, G) Voltage code (ex. 6.3V:6R3, 10V:100, 35V:350) Series code Category Please refer to "Product code guide (surface mount type)" ◆STANDARD RATINGS WV (Vdc) Cap (µF) 680 1,500 2,200 470 1,000 1,500 330 680 1,000 220 470 820 150 330 560 100 220 330 6.3 10 16 25 35 50 Size code tanδ ESR (Ω max./20℃, 100kHz) Rated ripple current (mArms/105℃, 100kHz) Part No. F80 HA0 JA0 F80 HA0 JA0 F80 HA0 JA0 F80 HA0 JA0 F80 HA0 JA0 F80 HA0 JA0 0.26 0.26 0.26 0.19 0.19 0.19 0.16 0.16 0.16 0.14 0.14 0.14 0.12 0.12 0.12 0.10 0.10 0.10 0.16 0.08 0.06 0.16 0.08 0.06 0.16 0.08 0.06 0.16 0.08 0.06 0.16 0.08 0.06 0.34 0.18 0.12 600 850 1,190 600 850 1,190 600 850 1,190 600 850 1,190 600 850 1,190 350 670 900 EMZR6R3ADA681MF80G EMZR6R3□DA152MHA0G EMZR6R3□DA222MJA0G EMZR100ADA471MF80G EMZR100□DA102MHA0G EMZR100□DA152MJA0G EMZR160ADA331MF80G EMZR160□DA681MHA0G EMZR160□DA102MJA0G EMZR250ADA221MF80G EMZR250□DA471MHA0G EMZR250□DA821MJA0G EMZR350ADA151MF80G EMZR350□DA331MHA0G EMZR350□DA561MJA0G EMZR500ADA101MF80G EMZR500□DA221MHA0G EMZR500□DA331MJA0G □ : Enter the appropriate terminal code. ◆RATED RIPPLE CURRENT MULTIPLIERS ・Frequency Multipliers Capacitance(µF) Frequency(Hz) 100 to 150 220 to 560 680 to 2,200 120 0.40 0.50 0.60 1k 0.75 0.85 0.87 10k 0.90 0.94 0.95 100k 1.00 1.00 1.00 The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5℃ rise. When long life performance is required in actual use, the rms ripple current has to be reduced. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 97 CAT. No. E1001Q