ADC200 SERIES 1W, High Isolation SIP, Single & Dual Output DC/DC Converters Selection Guide Model Number The ADC200 series is an excellent selection for a variety of applications including distributed power systems, mixed analog/digital subsystems, portable test equipments, local power networks and battery backed systems. 2.54 [0.100] 2.1 [0.08] 18.5 [0.73] 1 2 5 6 0.50 [0.020] 7 Load Regulation % Max. 10 10 8 7 7 10 8 7 7 8 8 5 5 5 8 5 5 5 8 8 5 5 5 8 5 5 5 % Typ. 73 71 76 78 78 72 77 78 79 74 73 78 80 80 74 79 81 81 73 71 76 78 79 72 76 79 80 Pin Singles Duals 1 2 5 6 7 +Vin -Vin -Vout No Pin +Vout +Vin -Vin -Vout Common +Vout Case Size – 5V & 12V Input – 19.5x6.1x10.2mm (0.77x0.24x0.40inch) 24V Input –19.5x7.1x10.2mm (0.77x0.28x0.40inch) Case Material – Non-Conductive Black Plastic Weight – 5V & 12V Input – 2.2g (0.08Oz) 24V Input– 2.6g (0.09Oz) Tolerance Millimeters X.X±0.25 X.XX±0.13 Inches X.XX±0.01 X.XXX±0.005 Pin ±0.05 ±0.002 T= 6.1 (0.24) for 5V & 12V Input Models T= 7.1 (0.28) for 24V Input Models Efficiency Pin Connections 19.5 [0.77] 3.2 [0.13] The series consists of 27 models with input voltages of 5V, 12V and 24VDC which offers standard output voltages of 3.3V, 5V, 9V, 12V, 15V, ±5V, ±9V, ±12V and ±15VDC for a wide choice. Mechanical Dimensions T MPS Industries ADC200 1W DC/DC's are specially designed to provide high levels of isolation 3000VDC in a miniature SIP package. 24 (21.6 – 26.4) Output Current mA 260 200 110 84 67 ±100 ±56 ±42 ±34 260 200 110 84 67 ±100 ±56 ±42 ±34 260 200 110 84 67 ±100 ±56 ±42 ±34 10.2 [0.40] • • • 12 (10.8 – 13.2) 0.5 [0.02] • Efficiency up to 81% 3000VDC Isolation MTBF > 2,000,000 Hours Low Cost Input 5, 12 and 24VDC Output 3.3, 5, 9, 12, 15, ±5, ±9, ±12 and ±15VDC Temperature Performance -40°C to +85°C UL 94V-0 Package Material Internal SMD Construction Industry Standard Pinout 5 (4.5 – 5.5) 1.3 [0.05] • • • • • • ADC201 ADC202 ADC203 ADC204 ADC205 ADC206 ADC207 ADC208 ADC209 ADC211 ADC212 ADC213 ADC214 ADC215 ADC216 ADC217 ADC218 ADC219 ADC221 ADC222 ADC223 ADC224 ADC225 ADC226 ADC227 ADC228 ADC229 Output Voltage VDC 3.3 5 9 12 15 ±5 ±9 ±12 ±15 3.3 5 9 12 15 ±5 ±9 ±12 ±15 3.3 5 9 12 15 ±5 ±9 ±12 ±15 0.25 [0.010] Key Features Input Voltage VDC 2463 208th Street, Ste. 205 Tel: (310) 533-1455 http://www.mpsind.com Torrance, CA 90501 Fax: (310) 533-1853 E-mail: [email protected] ADC200 SERIES 1W, High Isolation SIP, Single & Dual Output DC/DC Converters Absolute Maximum Ratings Parameter General Characteristics Min. 5VDC Input Models Max. Units -0.7 9 VDC Input Surge Voltage 12VDC Input Models (1000mS) -0.7 18 VDC 24VDC Input Models -0.7 30 VDC Lead Temperature (1.5mm from case for 10sec.) --- 260 °C Internal Power Dissipation --- 450 mW Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Conditions Min. Typ. Max. Units 60 Seconds 3000 --- --- VDC 500VDC 10 --- --- GΩ 100kHz, 1V --- 60 100 pF 70 100 120 kHz 2 --- --- MHrs Min. Typ. Max. Units --- ±1.2 ±1.5 % Switching Frequency MIL-HDBK-217F @25°C Ground Benign Exceeding the unit absolute maximum ratings could cause damage. These are not continuous operating ratings. MTBF Environmental Characteristics Output Characteristics Parameter Conditions Min. Ambient -40 85 °C Line Regulation Case -40 90 °C Load Regulation -40 125 °C Ripple & Noise --95 Free-Air Convection % Short Circuit Operating Temperature Operating Temperature Storage Temperature Humidity Cooling Max. Units Parameter Conditions For Vin Change of 1% See Selection Guide Io = 20% to 100% 20MHz BW --- 65 100 % mV P-P 0.5 Second Max. Maximum Capacitive Load Derating Curve (3.3, 5 & ±5V Outputs) 100 100LFM 200LFM Natural convection 400LFM Output Power (%) 80 60 40 20 0 ¡ã -40 50 70 60 90 80 Ambient Temperature 100 110 ] Derating Curve (Other Outputs) 100 100LFM 400LFM 200LFM Output Power (%) 80 Models by Output Voltage (Each Output on Duals) Singles Duals Units 220 100 uF Notes: 1. Specifications typical at Ta=+25°C, resistive load, nominal input voltage, rated output current unless otherwise noted. 2. These power converters require a minimum output load to maintain specified regulation. 3. Operation under no-load conditions will not damage these modules; however, they may not meet all specifications listed. 4. All DC/DC converters should be externally fused at the front end for protection. 5. Other input and output voltage may be available, please contact factory. 6. All specifications subject to change without notice. 7. For detailed data sheet, please visit our website. 60 Natural convection 40 20 0 ¡ã -40 50 60 70 80 Ambient Temperature 90 100 110 ] 2463 208th Street, Ste. 205 Tel: (310) 533-1455 http://www.mpsind.com Torrance, CA 90501 Fax: (310) 533-1853 E-mail: [email protected]