BP5075-5 AC/DC converter AC100V input, −5V/120mA output Dimensions (Unit : mm) Absolute Maximum Ratings Unit Vin Topr Tstg Tsmax Iopeak −170 −20 to +80 −25 to +105 105 120 V °C °C °C mApk 10.7MAX. 20.5MAX. Mark Side Limits 19.5MAX. Symbol 4.0±1.0 Parameter Input voltage Operating temperature range Storage temperature range Maximum surface temperature Maximum output current 1 4 5 6 7 0.5±0.1 3.25MAX. P=2.54±0.2 1.3±0.2 0.25±0.05 6.25MAX. 4.45MAX. 2.54x6=15.24TYP. Electrical Characteristics Conditions DC Vin=−141V, Io=60mA Unit V V mA V V Vp-p % Derating Curve ∗1 Vin=−113 to −170V, Io=60mA Vin=−141V, Io=0 to 60mA Vin=−141V, Io=60mA ∗2 Vin=−141V, Io=120mA ∗1 Maximum output current varies depending on ambient temperature ; please refer to derating curve. ∗2 An output ripple voltage sometimes change in capacitor to use, the measurement environment. BP5075-5 Be sure to use fuse for safety. 1 D1 R1 4 5 6 Functions Input terminal Not used Not used COMMON COMMON NC Output terminal Vin + − C1 C3 C2 80 Operation Range 60 40 20 0 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 Ambient Temperature Ta(°C) 40 35 30 25 20 15 10 5 0 0 + − V − Vo For actual usage, Please kindly evaluate and confirm our part mounted in your product, Especially, Please make sure to confirm whether the load current exceed Max. rated current by using the current probe. 100 90 80 70 60 50 40 30 20 10 0 0 External components setting Capacitance : 3.3µF to 33µF Rated voltage : 250V or higher C2: Capacitor for Output voltage smoothing 20 40 60 80 100 Output Current Io(mA) 120 Capacitance : 47µF to 470µF Rated voltage : 16V or higher, Low impedance part Impedance is 0.42Ω max at High frequency range. Ripple current is 0.2Arms above. Impedance of capacitor affects the output ripple voltage. C3: For noise terminal voltage reduction Capacitance : 0.1µF to 0.22µF Rated voltage : 250V or higher Film capacitor or ceramic capacitor. Reduce the noise terminal voltage. The constant value should be evaluated in the set. D1: Rectifier diode In the absolute maximum ratings, the reverse peak voltage should be 400V or higher, the average rectifying current should be 1A or higher, and the forward surge current should be 40A or higher. R1: For noise terminal voltage reduction 10Ω to 22Ω 1/4W Reduce the noise terminal voltage. The constant value should be evaluated in set. ZNR: Varistor Varistor must be used. It protects this part from lightning surge and static electricity. Conversion Efficiency (Ta=25°C, Vi= −141V) 20 40 60 80 100 Output Current Io(mA) 120 Load Regulation Load Regulation (Ta=25°C, Vi= −141V) -6.0 Output Voltage Vo(V) Please make sure to use fuse 1.0A C1: Capacitor for input voltage smoothing -5.0 -4.0 -3.0 Maximum Io=120mA -2.0 -1.0 0.0 0 20 40 60 80 100 120 140 160 Output Current Io(mA) Surface Temperature Rising Surface Temperature Increase ∆T(°C) FUSE: Fuse Switching Frequency (Ta=25°C, Vi= −141V) Conversion Efficiency A ZNR 100 7 FUSE − 120 Switching frequency Application circuit Pin No. 1 2 3 4 5 6 7 Derating Curve 140 Output Current Io(mA) Max. −170 −5.3 120 0.20 0.20 0.20 − Switching Frequency fsw(kHz) Typ. −141 −5.0 − 0.02 0.03 0.04 59 Conversion Efficiency η(%) Symbol Min. Parameter Input voltage −113 Vin Output voltage −4.7 Vo Output current − Io Line regulation − Vr Load regulation − Vl Output ripple voltage − Vp Power conversion efficiency 55 η Surface Temperature Increase (Ta=25°C, Vi= −141V) 40 35 30 25 20 15 10 5 0 0 20 40 60 80 100 Output Current Io(mA) 120 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2007 ROHM CO.,LTD. THE AMERICAS / EUPOPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21, Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0