anyCAP® 100 mA Low Dropout Linear Regulator ADP3309 FEATURES FUNCTIONAL BLOCK DIAGRAM ADP3309 Q1 IN THERMAL PROTECTION ERR/NC R1 CC Q2 OUT gm DRIVER R2 SD BANDGAP REF 00141-001 ±1.2% accuracy over line and load regulations @ 25°C Ultralow dropout voltage: 120 mV typical @ 100 mA Requires only COUT = 0.47 μF for stability anyCAP LDOs are stable with all types of capacitors (including MLCC) Current and thermal limiting Low noise Low shutdown current: 1 μA 2.8 V to 12 V supply range −20°C to +85°C ambient temperature range Several fixed voltage options Ultrasmall 5-lead SOT-23 package Excellent line and load regulations GND Figure 1. APPLICATIONS Cellular telephones Notebook, palmtop computers Battery-powered systems PCMCIA regulator Bar code scanners Camcorders, cameras GENERAL DESCRIPTION The ADP3309 operates with a wide input voltage range from 2.8 V to 12 V and delivers a load current in excess of 100 mA. The ADP3309 anyCAP LDO offers a wide range of output voltages. ERR/NC 4 ADP3309-3.3 VIN C1 + 0.47µF – 1 VOUT = 3.3V OUT 5 IN 2 3 + – C2 0.47µF ON OFF SD GND 00141-002 The ADP3309 is a member of the ADP330x family of precision low dropout anyCAP voltage regulators. It is pin-for-pin and functionally compatible with National’s LP2981, but offers performance advantages. The ADP3309 stands out from conventional LDOs with a novel architecture and an enhanced process. Its patented design requires only a 0.47 μF output capacitor for stability. This device is stable with any type of capacitor regardless of its equivalent series resistance (ESR) value, including ceramic types for space restricted applications. The ADP3309 achieves ±1.2% accuracy at room temperature and ±2.2% overall accuracy over temperature, line, and load regulations. The dropout voltage of the ADP3309 is only 120 mV (typical) at 100 mA. This device also includes a current limit and a shutdown feature. In shutdown mode, the ground current is reduced to ~1 μA. Figure 2. Typical Application Circuit Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2006 Analog Devices, Inc. All rights reserved. ADP3309 TABLE OF CONTENTS Features .............................................................................................. 1 Capacitor Selection: anyCAP.................................................... 10 Applications....................................................................................... 1 Thermal Overload Protection .................................................. 10 Functional Block Diagram .............................................................. 1 Calculating Junction Temperature........................................... 10 General Description ......................................................................... 1 Printed Circuit Board Layout Consideration ......................... 10 Revision History ............................................................................... 2 Shutdown Mode ......................................................................... 10 Specifications..................................................................................... 3 Error Flag Dropout Detector .................................................... 10 Absolute Maximum Ratings............................................................ 4 Application Circuits ....................................................................... 11 ESD Caution.................................................................................. 4 Crossover Switch ........................................................................ 11 Pin Configuration and Function Descriptions............................. 5 Higher Output Current ............................................................. 11 Typical Performance Characteristics ............................................. 6 Constant Dropout Post Regulator............................................ 11 Theory of Operation ........................................................................ 9 Outline Dimensions ....................................................................... 12 Application Information................................................................ 10 Ordering Guide .......................................................................... 12 REVISION HISTORY 12/06—Rev. B to Rev. C Change to Table 1 ............................................................................. 3 Updated Outline Dimensions ....................................................... 12 Changes to the Ordering Guide.................................................... 12 7/04—Rev. A to Rev. B. Changes to the Ordering Guide...................................................... 3 Updated Outline Dimensions ......................................................... 8 12/00—Rev. 0 to Rev. A 9/98—Revision 0: Initial Version Rev. C | Page 2 of 12 ADP3309 SPECIFICATIONS @ TA = −20°C to +85°C, VIN = 7 V, CIN = 0.47 μF, COUT = 0.47 μF, unless otherwise noted. 1 The following specifications apply to all voltage options. Table 1. Parameter Output Voltage Accuracy Line Regulation Symbol VOUT ΔVOUT ΔVIN Load Regulation ΔVOUT Ground Current IGND Ground Current in Dropout Dropout Voltage IGND VDROP Conditions VIN = VOUTNOM + 0.3 V to 12 V, IL = 0.1 mA to 100 mA, TA = 25°C VIN = VOUTNOM + 0.3 V to 12 V, IL = 0.1 mA to 100 mA VIN = VOUTNOM + 0.3 V to 12 V, TA = 25°C Min −1.2 Typ −2.2 Max +1.2 Unit % +2.2 % 0.02 mV/V IL = 0.1 mA to 100 mA, TA = 25°C 0.06 mV/mA 0.8 0.19 0.9 2.0 0.3 1.7 mA mA mA 0.12 0.025 0.004 0.25 0.07 0.015 V V V V V μA ΔIL Shutdown Threshold VTHSD Shutdown Pin Input Current ISDIN IL = 100 mA IL = 0.1 mA VIN = 2.4 V, IL = 0.1 mA VOUT = 98% of VOUTNOM IL = 100 mA IL = 10 mA IL = 1 mA On Off 0 < VSD ≤ 5 V 9 μA Ground Current in Shutdown Mode IQ VSD = 0 V, VIN = 12 V, TA = 25°C 0.005 1 μA VSD = 0 V, VIN = 12 V, TA = 85°C 0.01 3 μA Output Current in Shutdown Mode IOSD Error Pin Output Leakage Error Pin Output Low Voltage Peak Load Current Output Noise @ 5 V Input IEL VEOL ILDPK VNOISE TA = 25°C @ VIN = 12 V TA = 85°C @ VIN = 12 V VEO = 5 V ISINK = 400 μA VIN = VOUTNOM + 1 V, TA = 25°C f = 10 Hz to 100 kHz 2 4 13 0.3 μA μA μA V mA μV rms 2.0 0.3 1 5 < VSD ≤ 12 V @ VIN = 12 V 1 Ambient temperature of 85°C corresponds to a junction temperature of 125°C under typical full load test conditions. Rev. C | Page 3 of 12 0.12 150 100 ADP3309 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Input Supply Voltage Shutdown Input Voltage Power Dissipation Operating Ambient Temperature Range Operating Junction Temperature Range θJA θJC Storage Temperature Range Lead Temperature (Soldering 10 sec) Vapor Phase (60 sec) Infrared (15 sec) Rating −0.3 V to +16 V −0.3 V to +16 V Internally Limited −55°C to +125°C −55°C to +125°C 190°C/W 92°C/W −65°C to +150°C 300°C 215°C 220°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION Rev. C | Page 4 of 12 ADP3309 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS GND 2 SD 3 ADP3309 5 OUT 3 ERR/NC TOP VIEW (Not to Scale) NC = NO CONNECT 00141-003 IN 1 Figure 3. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 2 3 Mnemonic IN GND SD 4 ERR/NC 5 OUT Description Regulator Input. Ground Pin. Active Low Shutdown Pin. Connect to ground to disable the regulator output. When shutdown is not used, this pin should be connected to the input pin. Open Collector. Output that goes low to indicate the output is about to go out of regulation. This pin can be left open. (NC = No Connect). Output of the Regulator. Fixed 2.5 V, 2.7 V, 2.85 V, 2.9 V, 3.0 V, 3.3 V, or 3.6 V output voltage. Bypass to ground with a 0.47 μF or larger capacitor. Rev. C | Page 5 of 12 ADP3309 TYPICAL PERFORMANCE CHARACTERISTICS 3.302 900 VOUT = 3.3V IL = 0mA IL = 0 TO 100mA 3.301 3.300 GROUND CURRENT (µA) OUTPUT VOLTAGE (V) 750 IL = 10mA 3.299 IL = 50mA 3.298 3.297 600 450 300 3.296 7 8 9 10 INPUT VOLTAGE (V) 11 12 13 14 150 0 Figure 4. Line Regulation: Output Voltage vs. Supply Voltage 75 OUTPUT VOLTAGE (%) 3.299 3.298 3.297 0 135 IL = 0mA –0.1 IL = 100mA –0.2 –0.3 3.296 10 20 30 40 50 60 70 OUTPUT LOAD (mA) 80 90 100 –0.4 –45 00141-005 0 –25 –5 15 35 55 75 TEMPERATURE (°C) 95 115 Figure 8. Output Voltage Variation % vs. Temperature Figure 5. Output Voltage vs. Load Current 1150 1250 VOUT = 3.3V IL = 0mA VIN = 7V 900 GROUND CURRENT (µA) 1000 650 400 IL = 100mA 750 500 IL = 0mA 250 150 0 1.2 2.4 3.6 4.8 6.0 7.2 8.4 INPUT VOLTAGE (V) 9.6 10.8 12.0 0 –25 00141-006 GROUND CURRENT (µA) 135 IL = 50mA 0.1 3.300 0 100 0.2 VOUT = 3.3V VIN = 7V 3.301 OUTPUT VOLTAGE (V) 50 OUTPUT LOAD (mA) Figure 7. Quiescent Current vs. Load Current 3.302 3.295 25 00141-007 6 00141-008 5 00141-004 4 00141-009 IL = 100mA 3.295 3.3 Figure 6. Quiescent Current vs. Supply Voltage –5 15 35 55 75 TEMPERATURE (°C) 95 115 Figure 9. Quiescent Current vs. Temperature Rev. C | Page 6 of 12 ADP3309 120 3.32 VOUT = 3.3V 96 3.30 3.29 72 VOLTS INPUT/OUTPUT VOLTAGE (mV) 3.31 RL = 33Ω CL = 0.47µF 3.28 48 VIN 7.50 24 50 OUTPUT LOAD (mA) 75 100 0 40 Figure 10. Dropout Voltage vs. Output Current 120 160 200 240 TIME (µs) 280 320 360 400 180 200 500 Figure 13. Line Transient Response 5 3.32 VOUT = 3.3V RL = 33Ω VOUT = 3.3V 3.31 4 3.30 3.29 3 VOLTS INPUT/OUTPUT VOLTAGE (V) 80 00141-013 25 00141-014 0 00141-015 0 00141-010 7.00 2 RL = 3.3kΩ CL = 0.47µF 3.28 VIN 7.50 1 0 0 1 2 3 4 3 INPUT VOLTAGE (V) 2 1 0 00141-011 7.00 0 Figure 11. Power-Up/Power-Down 40 60 80 100 120 TIME (µs) 140 160 Figure 14. Line Transient Response 8 3.32 VSD = VIN CL = 0.47µF RL = 33Ω VOUT = 3.3V 6 VIN VOUT = 3.3V CL = 0.47µF 3.31 VOLTS 7 5 3.30 3.29 4 VOUT 3.28 3 mA 10 1 0 IOUT 100 2 0 20 40 60 80 100 120 TIME (µs) 140 160 180 200 00141-012 INPUT/OUTPUT VOLTAGE (V) 20 0 Figure 12. Power-Up Overshoot 100 200 300 TIME (µs) Figure 15. Load Transient Rev. C | Page 7 of 12 400 ADP3309 3.32 4 VOUT = 3.3V CL = 4.7µF 3.3V VOUT = 3.3V RL = 33Ω CL = 0.47µF 3 3.30 2 3.29 1 VOLTS VOLTS 3.31 3.28 0 IOUT 10 0 200 300 TIME (µs) 400 500 0 10 20 30 40 Figure 16. Load Transient Figure 19. Turn-Off 0 300 IOUT RIPPLE REJECTION (dB) 0 VOLTS 4 VOUT = 3.3V 2 –40 d –50 –60 a b –70 VOUT c 0.5 1.0 1.5 2.0 2.5 3.0 TIME (Seconds) 3.5 4.0 4.5 5.0 00141-017 –90 0 –100 a 10 VOLTAGE NOISE SPECTRAL DENSITY (µV/√Hz) 4 VOUT 3 CL = 0.47µF 3.3V 2 CL = 4.7µF VOUT = 3.3V RL = 33Ω 1 0 3 VSD 0 3V 40 60 TIME (µs) 80 100 100 1k 10k 100k FREQUENCY (Hz) 1M 10M 10 VOUT = 3.3V, CL = 0.47µF IL = 1mA 1 0.1 0.01 100 00141-018 20 c Figure 20. Power Supply Ripple Rejection Figure 17. Short-Circuit Current VOLTS d –80 0 0 b –30 00141-020 mA –20 100 VOUT = 3.3V a. 0.47µF, RL = 33kΩ b. 0.47µF, RL = 33Ω c. 10µF, RL = 33kΩ d. 10µF, RL = 33Ω –10 200 50 TIME (µs) 1k 10k FREQUENCY (Hz) Figure 21. Output Noise Density Figure 18. Turn-On Rev. C | Page 8 of 12 100k 00141-021 100 00141-016 0 VSD 00141-019 3 mA 100 ADP3309 THEORY OF OPERATION The ADP3309 anyCAP LDO uses a single control loop for regulation and reference functions. The output voltage is sensed by a resistive voltage divider consisting of R1 and R2, which is varied to provide the available output voltage option. Feedback is taken from this network by way of a series diode (D1) and a second resistor divider (R3 and R4) to the input of an amplifier. INPUT OUTPUT Q1 COMPENSATION CAPACITOR NONINVERTING WIDEBAND DRIVER gm ATTENUATION (VBANDGAP /VOUT) R3 PTAT VOS R4 D1 PTAT CURRENT R1 (a) R2 RLOAD CLOAD 00141-022 ADP3309 GND Figure 22. Functional Block Diagram A very high gain error amplifier is used to control this loop. The amplifier is constructed in such a way that at equilibrium, it produces a large, temperature proportional input offset voltage that is repeatable and very well controlled. The temperature proportional offset voltage is combined with the complementary diode voltage to form a virtual band gap voltage, implicit in the network, although it never appears explicitly in the circuit. Ultimately, this patented design makes it possible to control the loop with only one amplifier. This technique also improves the noise characteristics of the amplifier by providing more flexibility on the trade-off of noise sources that leads to a low noise design. The R1, R2 divider is chosen in the same ratio as the band gap voltage to the output voltage. Although the R1, R2 resistor divider is loaded by the diode (D1), and a second divider consisting of R3 and R4, the values can be chosen to produce a temperature stable output. The patented amplifier controls a new and unique noninverting driver that drives the pass transistor (Q1). The use of this special noninverting driver enables the frequency compensation to include the load capacitor in a pole splitting arrangement to achieve reduced sensitivity to the value, type, and ESR of the load capacitance. Most LDOs place very strict requirements on the range of ESR values for the output capacitor because they are difficult to stabilize due to the uncertainty of load capacitance and resistance. Moreover, the ESR value, required to keep conventional LDOs stable, changes depending on load and temperature. These ESR limitations make designing with LDOs more difficult because of their unclear specifications and extreme variations over temperature. This is no longer true with the ADP3309 anyCAP LDO. It can be used with virtually any capacitor, with no constraint on the minimum ESR. This innovative design allows the circuit to be stable with just a small 0.47 μF capacitor on the output. Additional advantages of the design scheme include superior line noise rejection and very high regulator gain, which leads to excellent line, and load regulation. An impressive ±2.2% accuracy is guaranteed over line, load, and temperature. Additional features of the circuit include current limit and thermal shutdown. Compared to the standard solutions that give warning after the output has lost regulation, the ADP3309 provides improved system performance by enabling the ERR pin to give warning before the device loses regulation. As the chip’s temperature rises above 165°C, the circuit activates a soft thermal shutdown, indicated by a signal low on the ERR pin, to reduce the current to a safe level. Rev. C | Page 9 of 12 ADP3309 APPLICATION INFORMATION CAPACITOR SELECTION: anyCAP Output Capacitors: As with any micropower device, output transient response is a function of the output capacitance. The ADP3309 is stable with a wide range of capacitor values, types, and ESR (anyCAP). A capacitor as low as 0.47 μF is all that is needed for stability. However, larger capacitors can be used if high output current surges are anticipated. The ADP3309 is stable with extremely low ESR capacitors (ESR ≈ 0), such as multilayer ceramic capacitors (MLCC) or OSCON. Input Bypass Capacitor: An input bypass capacitor is not required. However, for applications where the input source is high impedance or far from the input pin, a bypass capacitor is recommended. Connecting a 0.47 μF capacitor from the input pin (Pin 1) to ground reduces the circuit’s sensitivity to PC board layout. If a bigger output capacitor is used, the input capacitor must be 1 μF minimum. PRINTED CIRCUIT BOARD LAYOUT CONSIDERATION Surface-mount components rely on the conductive traces or pads to transfer heat away from the device. Appropriate PC board layout techniques should be used to remove heat from the immediate vicinity of the package. The following general guidelines will be helpful when designing a board layout: 1. PC board traces with larger cross section areas remove more heat. For optimum results, use PC boards with thicker copper and/or wider traces. 2. Increase the surface area exposed to open air so heat can be removed by convection or forced air flow. 3. Do not use solder mask or silk screen on the heat dissipating traces because it increases the junction to ambient thermal resistance of the package. THERMAL OVERLOAD PROTECTION The ADP3309 is protected against damage due to excessive power dissipation by its thermal overload protection circuit, which limits the die temperature to a maximum of 165°C. Under extreme conditions (that is, high ambient temperature and power dissipation) where die temperature starts to rise above 165°C, the output current is reduced until the die temperature has dropped to a safe level. The output current is restored when the die temperature is reduced. Current and thermal limit protections are intended to protect the device against accidental overload conditions. For normal operation, device power dissipation should be externally limited so that junction temperatures do not exceed 125°C. CALCULATING JUNCTION TEMPERATURE Device power dissipation is calculated as follows: SHUTDOWN MODE Applying a TTL high signal to the shutdown pin or tying it to the input pin turns the output on. Pulling the shutdown pin down to a TTL low signal or tying it to ground turns the output off. In shutdown mode, quiescent current is reduced to less than 1 μA. ERROR FLAG DROPOUT DETECTOR The ADP3309 maintains its output voltage over a wide range of load, input voltage, and temperature conditions. If the output is about to lose regulation, for example, by reducing the supply voltage below the combined regulated output and dropout voltages, the ERR pin will be activated. The ERR output is an open collector that will be driven low. Once set, the ERR or flag’s hysteresis keeps the output low until a small margin of operating range is restored either by raising the supply voltage or reducing the load. PD = (VIN – VOUT) ILOAD + (VIN) IGND where: ILOAD is the load current. IGND is the ground current. VIN is the input voltage. VOUT is the output voltage. Assuming ILOAD = 100 mA, IGND = 2 mA, VIN = 5.0 V, and VOUT = 3.3 V, device power dissipation is PD = (5.0 − 3.3) 100 mA + 5.0 × 2 mA = 180 mW ΔT = TJ – TA = PD × θJA = 0.18 × 190 = 34.2°C With a maximum junction temperature of 125°C, this yields a maximum ambient temperature of ~90°C. Rev. C | Page 10 of 12 ADP3309 APPLICATION CIRCUITS VIN = 4V TO 8V The circuit in Figure 23 shows that two ADP3309s can be used to form a mixed supply voltage system. The output switches between two different levels selected by an external digital input. Output voltages can be any combination of voltages from the Ordering Guide of the data sheet. VIN = 4V TO 12V IN OUTPUT SELECT 4V 0V MJE253* IN SD ADP3309-2.7 SD OUT ADP3309-3.3 VOUT = 2.7V/3.3V OUT VOUT = 3.3V @ 1A R1 50Ω C1 47µF GND + C2 10µF ERR 00141-024 CROSSOVER SWITCH *AAVID531002 HEAT SINK IS USED Figure 24. Higher Output Current Linear Regulator GND CONSTANT DROPOUT POST REGULATOR + IN OUT + ADP3309-3.3 SD The circuit in Figure 25 provides high precision with low dropout for any regulated output voltage. It significantly reduces the ripple from a switching regulator while providing a constant dropout voltage, which limits the power dissipation of the LDO to 30 mW. The ADP3000 used in this circuit is a switching regulator in the step-up configuration. C2 0.47µF GND 00141-023 C1 1µF Figure 23. Crossover Switch HIGHER OUTPUT CURRENT The ADP3309 can source up to 100 mA without any heat sink or pass transistor. If higher current is needed, an appropriate pass transistor can be used, as in Figure 24, to increase the output current to 1 A. VIN = 2.5V TO 3.5V C1 100µF 10V D1 1N5817 ADP3309-3.3 IN R1 120Ω ILIM C2 100µF 10V VIN SW1 ADP3000-ADJ GND SW2 FB R2 30.1kΩ 1% SD VOUT = 3.3V @ 100mA OUT GND + C3 2.2µF Q2 2N3906 Q1 2N3906 R3 124kΩ 1% Figure 25. Constant Dropout Post Regulator Rev. C | Page 11 of 12 R4 274kΩ 00141-025 L1 6.8µF ADP3309 OUTLINE DIMENSIONS 2.90 BSC 5 4 2.80 BSC 1.60 BSC 1 2 3 PIN 1 0.95 BSC 1.90 BSC 1.30 1.15 0.90 1.45 MAX 0.15 MAX 0.50 0.30 0.22 0.08 SEATING PLANE 10° 5° 0° 0.60 0.45 0.30 COMPLIANT TO JEDEC STANDARDS MO-178-AA Figure 26. 5-Lead Small Outline Transistor Package [SOT-23] (RJ-5) Dimensions shown in millimeters ORDERING GUIDE Model ADP3309ART-2.5-RL ADP3309ART-2.5-RL7 ADP3309ARTZ-2.5RL7 1 ADP3309ART-2.7-RL ADP3309ART-2.7-RL7 ADP3309ARTZ-2.7-R71 ADP3309ART-2.85-R7 ADP3309ART-2.85-RL ADP3309ARTZ-2.85R71 ADP3309ART-2.9-RL ADP3309ART-2.9-RL7 ADP3309ARTZ-2.9-R71 ADP3309ART-3-REEL ADP3309ART-3-REEL7 ADP3309ARTZ-3REEL71 ADP3309ART-3.3-RL ADP3309ART-3.3-RL7 ADP3309ARTZ-3.3-R71 ADP3309ART-3.6-RL ADP3309ART-3.6-RL7 ADP3309ARTZ-3.6-R71 1 Temperature Range −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C −20°C to +85°C Voltage Output 2.5 V 2.5 V 2.5 V 2.7 V 2.7 V 2.7 V 2.85 V 2.85 V 2.85 V 2.9 V 2.9 V 2.9 V 3.0 V 3.0 V 3.0 V 3.3 V 3.3 V 3.3 V 3.6 V 3.6 V 3.6 V Z = Pb-free part, # denotes lead-free product may be top or bottom marked. ©2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C00141-0-12/06(C) Rev. C | Page 12 of 12 Package Description 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 5-Lead SOT-23 Package Option RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 RJ-5 Branding LDE LDE LDE# DNC DNC L1P DVC DVC L1R DWC DWC L1S DPC DPC DPC# DRC DRC L1Q DTC DTC L1T