CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS TM NPCAP Radial Lead PSK - Series PSK ・Super low ESR, high ripple current capability ・Downsized from PSE series (φ6.3×8L to φ5×8L) ・Long life (20,000 hours at 105℃) ・Solvent resistant type (see PRECAUTIONS AND GUIDELINES) ・RoHS Compliant ・Halogen Free Downsized PSE P56 ◆SPECIFICATIONS Items Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current*Note Dissipation Factor (tanδ) Low Temperature Characteristics (Max.Impedance Ratio) Endurance Bias Humidity Test Surge Voltage Test Failure Rate Characteristics -55 to +105℃ 2.5 to 6.3 Vdc ±20% (M) Rated voltage(V)×1.15 500µA max. (at 20℃, 120Hz) (at 105℃) (at 20℃ after 2 minutes) 0.10 max. (at 20℃, 120Hz) Z(-25℃)/Z(+20℃)≦1.15 Z(-55℃)/Z(+20℃)≦1.25 (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 20,000 hours at 105℃. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦150% of the initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦The initial specified value Leakage current ≦The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦The initial specified value Leakage current ≦The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃. ◆DIMENSIONS [mm] Code : E F±0.5 ● Terminal φD' φd Coated Case L' 15min. 4min. Size code E08 φD 5.0 φd 0.5(Note2) F 2.0 φD' φD+0.5max. L' L+1.0max. Note2 : 0.45 for rated vollage 2.5V ◆MARKING EX) 2.5V560µF K6D6 560 2.5V Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 52 CAT. No. E1001Q CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS TM NPCAP Radial Lead PSKSeries - ◆PART NUMBERING SYSTEM 1 2 3 4 A PSK 5 6 7 8 9 10 11 12 13 14 15 16 17 18 E AA 5 6 1 M E 0 8 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 560µF:561) Lead forming.Taping code Terminal code Voltage code (ex. 2.5V:2R5, 6.3V:6R3) Series code Category Please refer to "Product code guide (conductive polymer type)" ◆STANDARD RATINGS WV (Vdc) 2.5 4 6.3 Cap (µF) Case size φD×L (mm) ESR (mΩ max./20℃, 100k to 300kHz) Rated ripple current (mArms/105℃, 100kHz) Part No. 220 330 470 560 330 270 330 5 ×8 5× 8 5× 8 5× 8 5×8 5 ×8 5×8 7 7 7 7 8 10 8 4,350 4,350 4,350 4,350 4,050 3,700 4,050 APSK2R5E□□221ME08S APSK2R5E□□331ME08S APSK2R5E□□471ME08S APSK2R5E□□561ME08S APSK4R0E□□331ME08S APSK6R3E□□271ME08S APSK6R3E□□331ME08S □□ : Enter the appropriate lead forming or taping code. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. 53 CAT. No. E1001Q