TI1 C6416 Fixed-point digital signal processor Datasheet

SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Highest-Performance Fixed-Point Digital
Signal Processors (DSPs)
− 2-, 1.67-, 1.39-ns Instruction Cycle Time
− 600-MHz Clock Rate
− Eight 32-Bit Instructions/Cycle
− Twenty-Eight Operations/Cycle
− 4800 MIPS
− Fully Software-Compatible With C62x
− C6414/15/16 Devices Pin-Compatible
VelociTI.2 Extensions to VelociTI
Advanced Very-Long-Instruction-Word
(VLIW) TMS320C64x DSP Core
− Eight Highly Independent Functional
Units With VelociTI.2 Extensions:
− Six ALUs (32-/40-Bit), Each Supports
Single 32-Bit, Dual 16-Bit, or Quad
8-Bit Arithmetic per Clock Cycle
− Two Multipliers Support
Four 16 x 16-Bit Multiplies
(32-Bit Results) per Clock Cycle or
Eight 8 x 8-Bit Multiplies
(16-Bit Results) per Clock Cycle
− Non-Aligned Load-Store Architecture
− 64 32-Bit General-Purpose Registers
− Instruction Packing Reduces Code Size
− All Instructions Conditional
Instruction Set Features
− Byte-Addressable (8-/16-/32-/64-Bit Data)
− 8-Bit Overflow Protection
− Bit-Field Extract, Set, Clear
− Normalization, Saturation, Bit-Counting
− VelociTI.2 Increased Orthogonality
Viterbi Decoder Coprocessor (VCP) [C6416]
− Supports Over 500 7.95-Kbps AMR
− Programmable Code Parameters
Turbo Decoder Coprocessor (TCP) [C6416]
− Supports up to Six 2-Mbps 3GPP
(6 Iterations)
− Programmable Turbo Code and
Decoding Parameters
L1/L2 Memory Architecture
− 128K-Bit (16K-Byte) L1P Program Cache
(Direct Mapped)
− 128K-Bit (16K-Byte) L1D Data Cache
(2-Way Set-Associative)
− 8M-Bit (1024K-Byte) L2 Unified Mapped
RAM/Cache (Flexible Allocation)
Two External Memory Interfaces (EMIFs)
− One 64-Bit (EMIFA), One 16-Bit (EMIFB)
− Glueless Interface to Asynchronous
Memories (SRAM and EPROM) and
Synchronous Memories (SDRAM,
SBSRAM, ZBT SRAM, and FIFO)
− 1280M-Byte Total Addressable External
Memory Space
Enhanced Direct-Memory-Access (EDMA)
Controller (64 Independent Channels)
Host-Port Interface (HPI)
− User-Configurable Bus Width (32-/16-Bit)
32-Bit/33-MHz, 3.3-V PCI Master/Slave
Interface Conforms to PCI Specification 2.2
[C6415/C6416 ]
− Three PCI Bus Address Registers:
Prefetchable Memory
Non-Prefetchable Memory I/O
− Four-Wire Serial EEPROM Interface
− PCI Interrupt Request Under DSP
Program Control
− DSP Interrupt Via PCI I/O Cycle
Three Multichannel Buffered Serial Ports
− Direct Interface to T1/E1, MVIP, SCSA
Framers
− Up to 256 Channels Each
− ST-Bus-Switching-, AC97-Compatible
− Serial Peripheral Interface (SPI)
Compatible (Motorola)
Three 32-Bit General-Purpose Timers
Universal Test and Operations PHY
Interface for ATM (UTOPIA) [C6415/C6416]
− UTOPIA Level 2 Slave ATM Controller
− 8-Bit Transmit and Receive Operations
up to 50 MHz per Direction
− User-Defined Cell Format up to 64 Bytes
Sixteen General-Purpose I/O (GPIO) Pins
Flexible PLL Clock Generator
IEEE-1149.1 (JTAG†)
Boundary-Scan-Compatible
570-Pin Grid Array (PGA) Package (GAD
Suffix)
0.13-µm/6-Level Cu Metal Process (CMOS)
3.3-V I/Os, 1.4-V Internal
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
C62x, VelociTI.2, VelociTI, and TMS320C64x are trademarks of Texas Instruments.
Motorola is a trademark of Motorola, Inc.
† IEEE Standard 1149.1-1990 Standard-Test-Access Port and Boundary Scan Architecture.
Copyright  2004, Texas Instruments Incorporated
!"#$ % &'!!($ #% )'*+&#$ ,#$(!,'&$% &!" $ %)(&&#$% )(! $.( $(!"% (/#% %$!'"($%
%$#,#!, 0#!!#$1- !,'&$ )!&(%%2 ,(% $ (&(%%#!+1 &+',(
$(%$2 #++ )#!#"($(!%-
POST OFFICE BOX 1443
)!,'&$% &")+#$ $ 3 #++ )#!#"($(!% #!( $(%$(,
'+(%% $.(!0%( $(,- #++ $.(! )!,'&$% )!,'&$
)!&(%%2 ,(% $ (&(%%#!+1 &+',( $(%$2 #++ )#!#"($(!%-
• HOUSTON, TEXAS 77251−1443
1
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Table of Contents
revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
GAD PGA package (bottom view) . . . . . . . . . . . . . . . . . . . . . 3
description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
device compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
functional block and CPU (DSP core) diagram . . . . . . . . . . . 7
CPU (DSP core) description . . . . . . . . . . . . . . . . . . . . . . . . . . 8
memory map summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
peripheral register descriptions . . . . . . . . . . . . . . . . . . . . . . . 13
EDMA channel synchronization events . . . . . . . . . . . . . . . . 26
interrupt sources and interrupt selector . . . . . . . . . . . . . . . . 28
signal groups description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
device configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
multiplexed pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
debugging considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
terminal functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
development support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
documentation support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
clock PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
general-purpose input/output (GPIO) . . . . . . . . . . . . . . . . . . 70
power-down mode logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
power-supply sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . .
power-supply decoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IEEE 1149.1 JTAG compatibility statement . . . . . . . . . . . . .
EMIF device speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
POST OFFICE BOX 1443
71
73
73
74
74
bootmode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
absolute maximum ratings over operating case
temperature range . . . . . . . . . . . . . . . . . . . . . . . . . .
recommended operating conditions . . . . . . . . . . . . . . . .
electrical characteristics over recommended ranges of
supply voltage and operating case temperature .
75
76
76
77
recommended clock and control signal transition
behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
parameter measurement information . . . . . . . . . . . . . . . 78
input and output clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
asynchronous memory timing . . . . . . . . . . . . . . . . . . . . . 84
programmable synchronous interface timing . . . . . . . . 88
synchronous DRAM timing . . . . . . . . . . . . . . . . . . . . . . . . 93
HOLD/HOLDA timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
BUSREQ timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
reset timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
external interrupt timing . . . . . . . . . . . . . . . . . . . . . . . . . 107
host-port interface (HPI) timing . . . . . . . . . . . . . . . . . . . 108
peripheral component interconnect (PCI) timing
[C6415 and C6416 only] . . . . . . . . . . . . . . . . . . . . 113
multichannel buffered serial port (McBSP) timing . . . . 116
UTOPIA slave timing [C6415 and C6416 only] . . . . . . 124
timer timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
general-purpose input/output (GPIO) port timing . . . . 128
JTAG test-port timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
REVISION HISTORY
This data sheet revision history highlights the technical changes made to the SMJ320C6414, SMJ320C6415, and
SMJ320C6416 device-specific data sheet.
Scope: Applicable updates to the C64x device family, specifically relating to the C6414, C6415, and C6416
devices, have been incorporated.
PAGE(S)
NO.
All
3, 81, 82,
83
ADDITIONS/CHANGES/DELETIONS
Original release
Removed pin A24, changed Cycle-to-cycle jitter to Period jitter.
GAD Ceramic PGA package (bottom view)
GAD CERAMIC 570-PIN GRID ARRAY (PGA) PACKAGE
( BOTTOM VIEW )
AD
AC
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
8
9
10
11 13 15 17 19 21 23
12
14 16 18 20 22 24
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
3
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
description
The TMS320C64x DSPs (including the SMJ320C6414, SMJ320C6415, and SMJ320C6416 devices) are the
highest-performance fixed-point DSP generation in the TMS320C6000 DSP platform. The TMS320C64x
(C64x†) device is based on the second-generation high-performance, advanced VelociTI
very-long-instruction-word (VLIW) architecture (VelociTI.2) developed by Texas Instruments (TI), making
these DSPs an excellent choice for multichannel and multifunctional applications. The C64x is a
code-compatible member of the C6000 DSP platform.
With performance of up to 5760 million instructions per second (MIPS) at a clock rate of 720 MHz, the C64x
devices offer cost-effective solutions to high-performance DSP programming challenges. The C64x DSPs
possess the operational flexibility of high-speed controllers and the numerical capability of array processors.
The C64x DSP core processor has 64 general-purpose registers of 32-bit word length and eight highly
independent functional units—two multipliers for a 32-bit result and six arithmetic logic units (ALUs)— with
VelociTI.2 extensions. The VelociTI.2 extensions in the eight functional units include new instructions to
accelerate the performance in key applications and extend the parallelism of the VelociTI architecture. The
C64x can produce four 32-bit multiply-accumulates (MACs) per cycle for a total of 2400 million MACs per
second (MMACS), or eight 8-bit MACs per cycle for a total of 4800 MMACS. The C64x DSP also has
application-specific hardware logic, on-chip memory, and additional on-chip peripherals similar to the other
C6000 DSP platform devices.
The C6416 device has two high-performance embedded coprocessors [Viterbi Decoder Coprocessor (VCP)
and Turbo Decoder Coprocessor (TCP)] that significantly speed up channel-decoding operations on-chip. The
VCP operating at CPU clock divided-by-4 can decode over 500 7.95-Kbps adaptive multi-rate (AMR) [K = 9,
R = 1/3] voice channels. The VCP supports constraint lengths K = 5, 6, 7, 8, and 9, rates R = 1/2, 1/3, and 1/4,
and flexible polynomials, while generating hard decisions or soft decisions. The TCP operating at CPU clock
divided-by-2 can decode up to thirty-six 384-Kbps or six 2-Mbps turbo encoded channels (assuming 6
iterations). The TCP implements the max*log-map algorithm and is designed to support all polynomials and
rates required by Third-Generation Partnership Projects (3GPP and 3GPP2), with fully programmable frame
length and turbo interleaver. Decoding parameters such as the number of iterations and stopping criteria are
also programmable. Communications between the VCP/TCP and the CPU are carried out through the EDMA
controller.
The C64x uses a two-level cache-based architecture and has a powerful and diverse set of peripherals. The
Level 1 program cache (L1P) is a 128K-bit direct mapped cache and the Level 1 data cache (L1D) is a 128K-bit
2-way set-associative cache. The Level 2 memory/cache (L2) consists of an 8M-bit memory space that is
shared between program and data space. L2 memory can be configured as mapped memory or combinations
of cache (up to 256K bytes) and mapped memory. The peripheral set includes three multichannel buffered serial
ports (McBSPs); an 8-bit Universal Test and Operations PHY Interface for Asynchronous Transfer Mode (ATM)
Slave [UTOPIA Slave] port (C6415/C6416 only); three 32-bit general-purpose timers; a user-configurable 16-bit
or 32-bit host-port interface (HPI16/HPI32); a peripheral component interconnect (PCI) [C6415/C6416 only];
a general-purpose input/output port (GPIO) with 16 GPIO pins; and two glueless external memory interfaces
(64-bit EMIFA and 16-bit EMIFB‡), both of which are capable of interfacing to synchronous and asynchronous
memories and peripherals.
The C64x has a complete set of development tools which includes: an advanced C compiler with C64x-specific
enhancements, an assembly optimizer to simplify programming and scheduling, and a Windows debugger
interface for visibility into source code execution.
TMS320C6000, C64x, and C6000 are trademarks of Texas Instruments.
Windows is a registered trademark of the Microsoft Corporation.
All trademarks are the property of their respective owners.
† Throughout the remainder of this document, the SMJ320C6414, SMJ320C6415, and SMJ320C6416 shall be referred to as SMJ320C64x or
C64x where generic, and where specific, their individual full device part numbers will be used or abbreviated as C6414, C6415, or C6416.
‡ These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.
4
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
device characteristics
Table 1 provides an overview of the C6414, C6415, and C6416 DSPs. The table shows significant features of
the C64x devices, including the capacity of on-chip RAM, the peripherals, the CPU frequency, and the package
type with pin count.
Table 1. Characteristics of the C6414, C6415, and C6416 Processors
HARDWARE FEATURES
Peripherals
Not all peripherals pins
are available at the same
time. (For more details,
see the Device
Configuration section.)
Peripheral performance is
dependent on chip-level
configuration.
Decoder Coprocessors
C6414, C6415, AND C6416
EMIFA (64-bit bus width)
(default clock source = AECLKIN)
1
EMIFB (16-bit bus width)
(default clock source = BECLKIN)
1
EDMA (64 independent channels)
1
HPI (32- or 16-bit user selectable)
1 (HPI16 or HPI32)
PCI (32-bit) [DeviceID Register value 0xA106]
1 [C6415/C6416 only]
McBSPs
(default internal clock source = CPU/4 clock
frequency)
3
UTOPIA (8-bit mode)
1 [C6415/C6416 only]
32-Bit Timers
(default internal clock source = CPU/8 clock
frequency)
3
General-Purpose Input/Output 0 (GP0)
16
VCP
1 (C6416 only)
TCP
1 (C6416 only)
Size (Bytes)
On-Chip Memory
1056K
16K-Byte (16KB) L1 Program (L1P) Cache
16KB L1 Data (L1D) Cache
1024KB Unified Mapped RAM/Cache (L2)
Organization
CPU ID + CPU Rev ID
Control Status Register (CSR.[31:16])
Device_ID
Silicon Revision Identification Register
(DEVICE_REV [19:16])
Address: 0x01B0 0200
Frequency
MHz
Cycle Time
ns
0x0C01
DEVICE_REV[19:16]
1111
0001
0010 or 0000
600
1.67 ns (C6414, C6415, C6416) and
(C6414A, C6415A, C6416A)
[600-MHz CPU, 133-MHz EMIFA]†
Core (V)
Voltage
Silicon Revision
1.03 or earlier
1.03
1.1
1.4 V
I/O (V)
3.3 V
PLL Options
CLKIN frequency multiplier
Bypass (x1), x6, x12
PGA Package
33 x 33 mm
570-Pin PGA (GAD)
Process Technology
µm
Product Status
Product Preview (PP)
Advance Information (AI)
Production Data (PD)
0.13 µm
PD
† On these C64x devices, the rated EMIF speed affects only the SDRAM interface on EMIFA. For more detailed information, see the EMIF
Device Speed section of this data sheet.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
5
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
device compatibility
The C64x generation of devices has a diverse and powerful set of peripherals. The common peripheral set
and pin-compatibility that the C6414, C6415, and C6416 devices offer lead to easier system designs and faster
time to market. Table 2 identifies the peripherals and coprocessors that are available on the C6414, C6415, and
C6416 devices.
The C6414, C6415, and C6416 devices are pin-for-pin compatible, provided the following conditions are met:
All devices are using the same peripherals.
The C6414 is pin-for-pin compatible with the C6415/C6416 when the PCI and UTOPIA peripherals on the
C6415/C6416 are disabled.
The C6415 is pin-for-pin compatible with the C6416 when they are in the same peripheral selection mode.
[For more information on peripheral selection, see the Device Configurations section of this data sheet.]
The BEA[9:7] pins are properly pulled up/down.
[For more details on the device-specific BEA[9:7] pin configurations, see the Terminal Functions table of
this data sheet.]
Table 2. Peripherals and Coprocessors Available on the C6414, C6415, and C6416 Devices†‡
C6414
C6415
C6416
EMIFA (64-bit bus width)
PERIPHERALS/COPROCESSORS
√
√
√
EMIFB (16-bit bus width)
√
√
√
EDMA (64 independent channels)
√
√
√
HPI (32- or 16-bit user selectable)
√
√
√
PCI (32-bit) [Specification v2.2]
—
√
√
McBSPs (McBSP0, McBSP1, McBSP2)
√
√
√
UTOPIA (8-bit mode) [Specification v1.0]
—
√
√
Timers (32-bit) [TIMER0, TIMER1, TIMER2]
√
√
√
√
√
√
GPIOs (GP[15:0])
√
† — denotes peripheral/coprocessor is not available on this device.
‡ Not all peripherals pins are available at the same time. (For more details, see the Device Configuration section.)
VCP/TCP Coprocessors
—
—
For more detailed information on the device compatibility and similarities/differences among the C6414, C6415,
and C6416 devices, see the How To Begin Development Today With the TMS320C6414, TMS320C6415, and
TMS320C6416 DSPs application report (literature number SPRA718).
6
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
functional block and CPU (DSP core) diagram
C64x Digital Signal Processor
VCP†
L1P Cache
Direct-Mapped
16K Bytes Total
TCP†
SDRAM
64
SBSRAM
16
EMIF A
EMIF B
C64x DSP Core
ZBT SRAM
Instruction Fetch
Timer 2
FIFO
SRAM
Control
Registers
Instruction Dispatch
Advanced Instruction Packet
Timer 1
ROM/FLASH
Control
Logic
Instruction Decode
Timer 0
I/O Devices
Data Path A
A Register File
A31−A16
A15−A0
McBSP2
.L1
UTOPIA‡
UTOPIA:
Up to 400 Mbps
Master ATMC
or
McBSPs:
Framing Chips:
H.100, MVIP,
SCSA, T1, E1
AC97 Devices,
SPI Devices,
Codecs
Enhanced
DMA
Controller
(64-channel)
.S1
.M1 .D1
Data Path B
Test
B Register File
B31−B16
B15−B0
.D2 .M2 .S2
Advanced
In-Circuit
Emulation
.L2
L2
Memory
1024K
Bytes
Interrupt
Control
McBSP1‡
L1D Cache
2-Way Set-Associative
16K Bytes Total
McBSP0
16
GPIO[8:0]
GPIO[15:9]‡
32
HPI‡
or
PCI‡
Boot Configuration
PLL
(x1, x6, x12)
Power-Down
Logic
Interrupt
Selector
† VCP and TCP decoder coprocessors are applicable to the C6416 device only.
‡ For the C6415 and C6416 devices, the UTOPIA peripheral is MUXed with McBSP1, and the PCI peripheral is MUXed with the HPI
peripheral and the GPIO[15:9] port. For more details on the multiplexed pins of these peripherals, see the Device Configurations section
of this data sheet.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
7
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
CPU (DSP core) description
The CPU fetches VelociTI advanced very-long instruction words (VLIWs) (256 bits wide) to supply up to eight
32-bit instructions to the eight functional units during every clock cycle. The VelociTI VLIW architecture
features controls by which all eight units do not have to be supplied with instructions if they are not ready to
execute. The first bit of every 32-bit instruction determines if the next instruction belongs to the same execute
packet as the previous instruction, or whether it should be executed in the following clock as a part of the next
execute packet. Fetch packets are always 256 bits wide; however, the execute packets can vary in size. The
variable-length execute packets are a key memory-saving feature, distinguishing the C64x CPUs from other
VLIW architectures. The C64x VelociTI.2 extensions add enhancements to the TMS320C62x DSP
VelociTI architecture. These enhancements include:
Register file enhancements
Data path extensions
Quad 8-bit and dual 16-bit extensions with data flow enhancements
Additional functional unit hardware
Increased orthogonality of the instruction set
Additional instructions that reduce code size and increase register flexibility
The CPU features two sets of functional units. Each set contains four units and a register file. One set contains
functional units .L1, .S1, .M1, and .D1; the other set contains units .D2, .M2, .S2, and .L2. The two register files
each contain 32 32-bit registers for a total of 64 general-purpose registers. In addition to supporting the packed
16-bit and 32-/40-bit fixed-point data types found in the C62x VelociTI VLIW architecture, the C64x register
files also support packed 8-bit data and 64-bit fixed-point data types. The two sets of functional units, along with
two register files, compose sides A and B of the CPU [see the functional block and CPU (DSP core) diagram,
and Figure 1]. The four functional units on each side of the CPU can freely share the 32 registers belonging to
that side. Additionally, each side features a “data cross path”—a single data bus connected to all the registers
on the other side, by which the two sets of functional units can access data from the register files on the opposite
side. The C64x CPU pipelines data-cross-path accesses over multiple clock cycles. This allows the same
register to be used as a data-cross-path operand by multiple functional units in the same execute packet. All
functional units in the C64x CPU can access operands via the data cross path. Register access by functional
units on the same side of the CPU as the register file can service all the units in a single clock cycle. On the C64x
CPU, a delay clock is introduced whenever an instruction attempts to read a register via a data cross path if that
register was updated in the previous clock cycle.
In addition to the C62x DSP fixed-point instructions, the C64x DSP includes a comprehensive collection of
quad 8-bit and dual 16-bit instruction set extensions. These VelociTI.2 extensions allow the C64x CPU to
operate directly on packed data to streamline data flow and increase instruction set efficiency.
Another key feature of the C64x CPU is the load/store architecture, where all instructions operate on registers
(as opposed to data in memory). Two sets of data-addressing units (.D1 and .D2) are responsible for all data
transfers between the register files and the memory. The data address driven by the .D units allows data
addresses generated from one register file to be used to load or store data to or from the other register file. The
C64x .D units can load and store bytes (8 bits), half-words (16 bits), and words (32 bits) with a single instruction.
And with the new data path extensions, the C64x .D unit can load and store doublewords (64 bits) with a single
instruction. Furthermore, the non-aligned load and store instructions allow the .D units to access words and
doublewords on any byte boundary. The C64x CPU supports a variety of indirect addressing modes using either
linear- or circular-addressing with 5- or 15-bit offsets. All instructions are conditional, and most can access any
one of the 64 registers. Some registers, however, are singled out to support specific addressing modes or to
hold the condition for conditional instructions (if the condition is not automatically “true”).
TMS320C62x is a trademark of Texas Instruments.
8
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
CPU (DSP core) description (continued)
The two .M functional units perform all multiplication operations. Each of the C64x .M units can perform two
16 × 16-bit multiplies or four 8 × 8-bit multiplies per clock cycle. The .M unit can also perform 16 × 32-bit multiply
operations, dual 16 × 16-bit multiplies with add/subtract operations, and quad 8 × 8-bit multiplies with add
operations. In addition to standard multiplies, the C64x .M units include bit-count, rotate, Galois field multiplies,
and bidirectional variable shift hardware.
The two .S and .L functional units perform a general set of arithmetic, logical, and branch functions with results
available every clock cycle. The arithmetic and logical functions on the C64x CPU include single 32-bit, dual
16-bit, and quad 8-bit operations.
The processing flow begins when a 256-bit-wide instruction fetch packet is fetched from a program memory.
The 32-bit instructions destined for the individual functional units are “linked” together by “1” bits in the least
significant bit (LSB) position of the instructions. The instructions that are “chained” together for simultaneous
execution (up to eight in total) compose an execute packet. A “0” in the LSB of an instruction breaks the chain,
effectively placing the instructions that follow it in the next execute packet. A C64x DSP device enhancement
now allows execute packets to cross fetch-packet boundaries. In the TMS320C62x/TMS320C67x DSP
devices, if an execute packet crosses the fetch-packet boundary (256 bits wide), the assembler places it in the
next fetch packet, while the remainder of the current fetch packet is padded with NOP instructions. In the C64x
DSP device, the execute boundary restrictions have been removed, thereby, eliminating all of the NOPs added
to pad the fetch packet, and thus, decreasing the overall code size. The number of execute packets within a
fetch packet can vary from one to eight. Execute packets are dispatched to their respective functional units at
the rate of one per clock cycle and the next 256-bit fetch packet is not fetched until all the execute packets from
the current fetch packet have been dispatched. After decoding, the instructions simultaneously drive all active
functional units for a maximum execution rate of eight instructions every clock cycle. While most results are
stored in 32-bit registers, they can be subsequently moved to memory as bytes, half-words, words, or
doublewords. All load and store instructions are byte-, half-word-, word-, or doubleword-addressable.
For more details on the C64x CPU functional units enhancements, see the following documents:
The TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189)
TMS320C64x Technical Overview (literature number SPRU395)
How To Begin Development Today With the TMS320C6414, TMS320C6415, and TMS320C6416 DSPs
application report (literature number SPRA718)
TMS320C67x is a trademark of Texas Instruments.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
9
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
CPU (DSP core) description (continued)
src1
.L1
src2
dst
long dst
long src
ST1b (Store Data)
ST1a (Store Data)
8
8
32 MSBs
32 LSBs
long src
long dst
dst
.S1 src1
Data Path A
8
8
Register
File A
(A0−A31)
src2
See Note A
See Note A
long dst
dst
.M1 src1
src2
LD1b (Load Data)
LD1a (Load Data)
32 MSBs
32 LSBs
DA1 (Address)
.D1
dst
src1
src2
2X
1X
src2
.D2
DA2 (Address)
LD2a (Load Data)
LD2b (Load Data)
src1
dst
32 LSBs
32 MSBs
src2
.M2 src1
dst
See Note A
See Note A
long dst
Register
File B
(B0− B31)
src2
Data Path B
.S2
src1
dst
long dst
long src
ST2a (Store Data)
ST2b (Store Data)
8
8
32 MSBs
32 LSBs
long src
long dst
dst
8
8
.L2 src2
src1
Control Register
File
NOTE A: For the .M functional units, the long dst is 32 MSBs and the dst is 32 LSBs.
Figure 1. SMJ320C64x CPU (DSP Core) Data Paths
10
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
memory map summary
Table 3 shows the memory map address ranges of the SMJ320C64x device. Internal memory is always located
at address 0 and can be used as both program and data memory. The external memory address ranges in the
C64x device begin at the hex address locations 0x6000 0000 for EMIFB and 0x8000 0000 for EMIFA.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
11
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
memory map summary (continued)
Table 3. SMJ320C64x Memory Map Summary
MEMORY BLOCK DESCRIPTION
BLOCK SIZE (BYTES)
Internal RAM (L2)
1M
Reserved
23M
External Memory Interface A (EMIFA) Registers
256K
L2 Registers
256K
HPI Registers
256K
McBSP 0 Registers
256K
McBSP 1 Registers
256K
Timer 0 Registers
256K
Timer 1 Registers
256K
Interrupt Selector Registers
256K
EDMA RAM and EDMA Registers
256K
McBSP 2 Registers
256K
EMIFB Registers
256K
Timer 2 Registers
256K
GPIO Registers
256K
UTOPIA Registers (C6415 and C6416 only)†
TCP/VCP Registers (C6416 only)‡
256K
Reserved
256K
PCI Registers (C6415 and C6416 only)†
256K
Reserved
256K
4M – 256K
QDMA Registers
52
Reserved
736M – 52
McBSP 0 Data
64M
McBSP 1 Data
64M
McBSP 2 Data
64M
UTOPIA Queues (C6415 and C6416 only)†
64M
Reserved
256M
TCP/VCP (C6416 only)‡
256M
EMIFB CE0
64M
EMIFB CE1
64M
EMIFB CE2
64M
EMIFB CE3
64M
Reserved
256M
EMIFA CE0
256M
EMIFA CE1
256M
EMIFA CE2
256M
EMIFA CE3
256M
Reserved
1G
HEX ADDRESS RANGE
0000
0010
0180
0184
0188
018C
0190
0194
0198
019C
01A0
01A4
01A8
01AC
01B0
01B4
01B8
01BC
01C0
01C4
0200
0200
3000
3400
3800
3C00
4000
5000
6000
6400
6800
6C00
7000
8000
9000
A000
B000
C000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0034
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
000F
017F
0183
0187
018B
018F
0193
0197
019B
019F
01A3
01A7
01AB
01AF
01B3
01B7
01BB
01BF
01C3
01FF
0200
2FFF
33FF
37FF
3BFF
3FFF
4FFF
5FFF
63FF
67FF
6BFF
6FFF
7FFF
8FFF
9FFF
AFFF
BFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
0033
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
FFFF
† For the C6414 device, these memory address locations are reserved. The C6414 device does not support the UTOPIA and PCI peripherals.
‡ Only the C6416 device supports the VCP/TCP Coprocessors. For the C6414 and C6415 devices, these memory address locations are reserved.
12
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions
Table 4 through Table 23 identify the peripheral registers for the C6414, C6415, and C6416 devices by their
register names, acronyms, and hex address or hex address range. For more detailed information on the register
contents, bit names and their descriptions, see the specific peripheral reference guide listed in the
TMS320C6000 DSP Peripherals Overview Reference Guide (literature number SPRU190).
Table 4. EMIFA Registers
HEX ADDRESS RANGE
ACRONYM
0180 0000
GBLCTL
EMIFA global control
REGISTER NAME
0180 0004
CECTL1
EMIFA CE1 space control
0180 0008
CECTL0
EMIFA CE0 space control
0180 000C
−
0180 0010
CECTL2
EMIFA CE2 space control
0180 0014
CECTL3
EMIFA CE3 space control
0180 0018
SDCTL
EMIFA SDRAM control
0180 001C
SDTIM
EMIFA SDRAM refresh control
0180 0020
SDEXT
EMIFA SDRAM extension
0180 0024 − 0180 003C
−
0180 0040
PDTCTL
Peripheral device transfer (PDT) control
0180 0044
CESEC1
EMIFA CE1 space secondary control
0180 0048
CESEC0
EMIFA CE0 space secondary control
Reserved
Reserved
0180 004C
−
0180 0050
CESEC2
Reserved
EMIFA CE2 space secondary control
0180 0054
CESEC3
EMIFA CE3 space secondary control
0180 0058 − 0183 FFFF
–
Reserved
Table 5. EMIFB Registers
HEX ADDRESS RANGE
ACRONYM
01A8 0000
GBLCTL
EMIFB global control
REGISTER NAME
01A8 0004
CECTL1
EMIFB CE1 space control
01A8 0008
CECTL0
EMIFB CE0 space control
01A8 000C
−
01A8 0010
CECTL2
EMIFB CE2 space control
01A8 0014
CECTL3
EMIFB CE3 space control
01A8 0018
SDCTL
EMIFB SDRAM control
01A8 001C
SDTIM
EMIFB SDRAM refresh control
01A8 0020
SDEXT
EMIFB SDRAM extension
01A8 0024 − 01A8 003C
−
01A8 0040
PDTCTL
Peripheral device transfer (PDT) control
01A8 0044
CESEC1
EMIFB CE1 space secondary control
01A8 0048
CESEC0
EMIFB CE0 space secondary control
01A8 004C
−
01A8 0050
CESEC2
EMIFB CE2 space secondary control
01A8 0054
CESEC3
EMIFB CE3 space secondary control
01A8 0058 − 01AB FFFF
–
Reserved
Reserved
Reserved
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
13
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 6. L2 Cache Registers
14
HEX ADDRESS RANGE
ACRONYM
0184 0000
CCFG
0184 0004 − 0184 0FFC
−
0184 1000
EDMAWEIGHT
REGISTER NAME
Cache configuration register
Reserved
L2 EDMA access control register
0184 1004 − 0184 1FFC
−
0184 2000
L2ALLOC0
Reserved
L2 allocation register 0
0184 2004
L2ALLOC1
L2 allocation register 1
0184 2008
L2ALLOC2
L2 allocation register 2
0184 200C
L2ALLOC3
L2 allocation register 3
0184 2010 − 0184 3FFC
−
0184 4000
L2FBAR
Reserved
L2 flush base address register
0184 4004
L2FWC
L2 flush word count register
0184 4010
L2CBAR
L2 clean base address register
0184 4014
L2CWC
L2 clean word count register
0184 4020
L1PFBAR
L1P flush base address register
0184 4024
L1PFWC
L1P flush word count register
0184 4030
L1DFBAR
L1D flush base address register
0184 4034
L1DFWC
L1D flush word count register
0184 4038 − 0184 4FFC
−
Reserved
0184 5000
L2FLUSH
L2 flush register
0184 5004
L2CLEAN
L2 clean register
0184 5008 − 0184 7FFC
−
Reserved
0184 8000 − 0184 817C
MAR0 to
MAR95
Reserved
0184 8180
MAR96
Controls EMIFB CE0 range 6000 0000 − 60FF FFFF
0184 8184
MAR97
Controls EMIFB CE0 range 6100 0000 − 61FF FFFF
0184 8188
MAR98
Controls EMIFB CE0 range 6200 0000 − 62FF FFFF
0184 818C
MAR99
Controls EMIFB CE0 range 6300 0000 − 63FF FFFF
0184 8190
MAR100
Controls EMIFB CE1 range 6400 0000 − 64FF FFFF
0184 8194
MAR101
Controls EMIFB CE1 range 6500 0000 − 65FF FFFF
0184 8198
MAR102
Controls EMIFB CE1 range 6600 0000 − 66FF FFFF
0184 819C
MAR103
Controls EMIFB CE1 range 6700 0000 − 67FF FFFF
0184 81A0
MAR104
Controls EMIFB CE2 range 6800 0000 − 68FF FFFF
0184 81A4
MAR105
Controls EMIFB CE2 range 6900 0000 − 69FF FFFF
0184 81A8
MAR106
Controls EMIFB CE2 range 6A00 0000 − 6AFF FFFF
0184 81AC
MAR107
Controls EMIFB CE2 range 6B00 0000 − 6BFF FFFF
0184 81B0
MAR108
Controls EMIFB CE3 range 6C00 0000 − 6CFF FFFF
0184 81B4
MAR109
Controls EMIFB CE3 range 6D00 0000 − 6DFF FFFF
0184 81B8
MAR110
Controls EMIFB CE3 range 6E00 0000 − 6EFF FFFF
0184 81BC
MAR111
Controls EMIFB CE3 range 6F00 0000 − 6FFF FFFF
0184 81C0 − 0184 81FC
MAR112 to
MAR127
0184 8200
MAR128
Controls EMIFA CE0 range 8000 0000 − 80FF FFFF
0184 8204
MAR129
Controls EMIFA CE0 range 8100 0000 − 81FF FFFF
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
COMMENTS
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Table 6. L2 Cache Registers (Continued)
HEX ADDRESS RANGE
ACRONYM
0184 8208
MAR130
Controls EMIFA CE0 range 8200 0000 − 82FF FFFF
REGISTER NAME
0184 820C
MAR131
Controls EMIFA CE0 range 8300 0000 − 83FF FFFF
0184 8210
MAR132
Controls EMIFA CE0 range 8400 0000 − 84FF FFFF
0184 8214
MAR133
Controls EMIFA CE0 range 8500 0000 − 85FF FFFF
0184 8218
MAR134
Controls EMIFA CE0 range 8600 0000 − 86FF FFFF
0184 821C
MAR135
Controls EMIFA CE0 range 8700 0000 − 87FF FFFF
0184 8220
MAR136
Controls EMIFA CE0 range 8800 0000 − 88FF FFFF
0184 8224
MAR137
Controls EMIFA CE0 range 8900 0000 − 89FF FFFF
0184 8228
MAR138
Controls EMIFA CE0 range 8A00 0000 − 8AFF FFFF
0184 822C
MAR139
Controls EMIFA CE0 range 8B00 0000 − 8BFF FFFF
0184 8230
MAR140
Controls EMIFA CE0 range 8C00 0000 − 8CFF FFFF
0184 8234
MAR141
Controls EMIFA CE0 range 8D00 0000 − 8DFF FFFF
0184 8238
MAR142
Controls EMIFA CE0 range 8E00 0000 − 8EFF FFFF
0184 823C
MAR143
Controls EMIFA CE0 range 8F00 0000 − 8FFF FFFF
0184 8240
MAR144
Controls EMIFA CE1 range 9000 0000 − 90FF FFFF
0184 8244
MAR145
Controls EMIFA CE1 range 9100 0000 − 91FF FFFF
0184 8248
MAR146
Controls EMIFA CE1 range 9200 0000 − 92FF FFFF
0184 824C
MAR147
Controls EMIFA CE1 range 9300 0000 − 93FF FFFF
0184 8250
MAR148
Controls EMIFA CE1 range 9400 0000 − 94FF FFFF
0184 8254
MAR149
Controls EMIFA CE1 range 9500 0000 − 95FF FFFF
0184 8258
MAR150
Controls EMIFA CE1 range 9600 0000 − 96FF FFFF
0184 825C
MAR151
Controls EMIFA CE1 range 9700 0000 − 97FF FFFF
0184 8260
MAR152
Controls EMIFA CE1 range 9800 0000 − 98FF FFFF
0184 8264
MAR153
Controls EMIFA CE1 range 9900 0000 − 99FF FFFF
0184 8268
MAR154
Controls EMIFA CE1 range 9A00 0000 − 9AFF FFFF
0184 826C
MAR155
Controls EMIFA CE1 range 9B00 0000 − 9BFF FFFF
0184 8270
MAR156
Controls EMIFA CE1 range 9C00 0000 − 9CFF FFFF
0184 8274
MAR157
Controls EMIFA CE1 range 9D00 0000 − 9DFF FFFF
0184 8278
MAR158
Controls EMIFA CE1 range 9E00 0000 − 9EFF FFFF
0184 827C
MAR159
Controls EMIFA CE1 range 9F00 0000 − 9FFF FFFF
0184 8280
MAR160
Controls EMIFA CE2 range A000 0000 − A0FF FFFF
0184 8284
MAR161
Controls EMIFA CE2 range A100 0000 − A1FF FFFF
0184 8288
MAR162
Controls EMIFA CE2 range A200 0000 − A2FF FFFF
0184 828C
MAR163
Controls EMIFA CE2 range A300 0000 − A3FF FFFF
0184 8290
MAR164
Controls EMIFA CE2 range A400 0000 − A4FF FFFF
0184 8294
MAR165
Controls EMIFA CE2 range A500 0000 − A5FF FFFF
0184 8298
MAR166
Controls EMIFA CE2 range A600 0000 − A6FF FFFF
0184 829C
MAR167
Controls EMIFA CE2 range A700 0000 − A7FF FFFF
0184 82A0
MAR168
Controls EMIFA CE2 range A800 0000 − A8FF FFFF
0184 82A4
MAR169
Controls EMIFA CE2 range A900 0000 − A9FF FFFF
0184 82A8
MAR170
Controls EMIFA CE2 range AA00 0000 − AAFF FFFF
0184 82AC
MAR171
Controls EMIFA CE2 range AB00 0000 − ABFF FFFF
0184 82B0
MAR172
Controls EMIFA CE2 range AC00 0000 − ACFF FFFF
0184 82B4
MAR173
Controls EMIFA CE2 range AD00 0000 − ADFF FFFF
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
COMMENTS
15
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Table 6. L2 Cache Registers (Continued)
16
HEX ADDRESS RANGE
ACRONYM
0184 82B8
MAR174
Controls EMIFA CE2 range AE00 0000 − AEFF FFFF
REGISTER NAME
0184 82BC
MAR175
Controls EMIFA CE2 range AF00 0000 − AFFF FFFF
0184 82C0
MAR176
Controls EMIFA CE3 range B000 0000 − B0FF FFFF
0184 82C4
MAR177
Controls EMIFA CE3 range B100 0000 − B1FF FFFF
0184 82C8
MAR178
Controls EMIFA CE3 range B200 0000 − B2FF FFFF
0184 82CC
MAR179
Controls EMIFA CE3 range B300 0000 − B3FF FFFF
0184 82D0
MAR180
Controls EMIFA CE3 range B400 0000 − B4FF FFFF
0184 82D4
MAR181
Controls EMIFA CE3 range B500 0000 − B5FF FFFF
0184 82D8
MAR182
Controls EMIFA CE3 range B600 0000 − B6FF FFFF
0184 82DC
MAR183
Controls EMIFA CE3 range B700 0000 − B7FF FFFF
0184 82E0
MAR184
Controls EMIFA CE3 range B800 0000 − B8FF FFFF
0184 82E4
MAR185
Controls EMIFA CE3 range B900 0000 − B9FF FFFF
0184 82E8
MAR186
Controls EMIFA CE3 range BA00 0000 − BAFF FFFF
0184 82EC
MAR187
Controls EMIFA CE3 range BB00 0000 − BBFF FFFF
0184 82F0
MAR188
Controls EMIFA CE3 range BC00 0000 − BCFF FFFF
0184 82F4
MAR189
Controls EMIFA CE3 range BD00 0000 − BDFF FFFF
0184 82F8
MAR190
Controls EMIFA CE3 range BE00 0000 − BEFF FFFF
0184 82FC
MAR191
Controls EMIFA CE3 range BF00 0000 − BFFF FFFF
0184 8300 − 0184 83FC
MAR192 to
MAR255
Reserved
0184 8400 − 0187 FFFF
−
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
COMMENTS
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 7. EDMA Registers
HEX ADDRESS RANGE
ACRONYM
01A0 FF9C
EPRH
Event polarity high register
REGISTER NAME
01A0 FFA4
CIPRH
Channel interrupt pending high register
01A0 FFA8
CIERH
Channel interrupt enable high register
01A0 FFAC
CCERH
Channel chain enable high register
01A0 FFB0
ERH
01A0 FFB4
EERH
Event enable high register
Event high register
01A0 FFB8
ECRH
Event clear high register
01A0 FFBC
ESRH
Event set high register
01A0 FFC0
PQAR0
Priority queue allocation register 0
01A0 FFC4
PQAR1
Priority queue allocation register 1
01A0 FFC8
PQAR2
Priority queue allocation register 2
01A0 FFCC
PQAR3
Priority queue allocation register 3
01A0 FFDC
EPRL
Event polarity low register
01A0 FFE0
PQSR
Priority queue status register
01A0 FFE4
CIPRL
Channel interrupt pending low register
01A0 FFE8
CIERL
Channel interrupt enable low register
01A0 FFEC
CCERL
Channel chain enable low register
01A0 FFF0
ERL
01A0 FFF4
EERL
Event enable low register
Event low register
01A0 FFF8
ECRL
Event clear low register
01A0 FFFC
ESRL
Event set low register
01A1 0000 − 01A3 FFFF
–
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
17
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 8. EDMA Parameter RAM†
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
01A0 0000 − 01A0 0017
−
Parameters for Event 0 (6 words)
01A0 0018 − 01A0 002F
−
Parameters for Event 1 (6 words)
01A0 0030 − 01A0 0047
−
Parameters for Event 2 (6 words)
01A0 0048 − 01A0 005F
−
Parameters for Event 3 (6 words)
01A0 0060 − 01A0 0077
−
Parameters for Event 4 (6 words)
01A0 0078 − 01A0 008F
−
Parameters for Event 5 (6 words)
01A0 0090 − 01A0 00A7
−
Parameters for Event 6 (6 words)
01A0 00A8 − 01A0 00BF
−
Parameters for Event 7 (6 words)
01A0 00C0 − 01A0 00D7
−
Parameters for Event 8 (6 words)
01A0 00D8 − 01A0 00EF
−
Parameters for Event 9 (6 words)
01A0 00F0 − 01A0 00107
−
Parameters for Event 10 (6 words)
01A0 0108 − 01A0 011F
−
Parameters for Event 11 (6 words)
01A0 0120 − 01A0 0137
−
Parameters for Event 12 (6 words)
01A0 0138 − 01A0 014F
−
Parameters for Event 13 (6 words)
01A0 0150 − 01A0 0167
−
Parameters for Event 14 (6 words)
01A0 0168 − 01A0 017F
−
Parameters for Event 15 (6 words)
01A0 0150 − 01A0 0167
−
Parameters for Event 16 (6 words)
01A0 0168 − 01A0 017F
−
Parameters for Event 17 (6 words)
...
...
...
...
01A0 05D0 − 01A0 05E7
−
Parameters for Event 62 (6 words)
01A0 05E8 − 01A0 05FF
−
Parameters for Event 63 (6 words)
01A0 0600 − 01A0 0617
−
Reload/link parameters for Event M (6 words)
01A0 0618 − 01A0 062F
−
Reload/link parameters for Event N (6 words)
...
...
01A0 07E0 − 01A0 07F7
−
01A0 07F8 − 01A0 07FF
−
Reload/link parameters for Event Z (6 words)
Scratch pad area (2 words)
† The C64x device has twenty-one parameter sets [six (6) words each] that can be used to reload/link EDMA transfers.
Table 9. Quick DMA (QDMA) and Pseudo Registers
HEX ADDRESS RANGE
ACRONYM
0200 0000
QOPT
QDMA options parameter register
0200 0004
QSRC
QDMA source address register
0200 0008
QCNT
QDMA frame count register
0200 000C
QDST
QDMA destination address register
0200 0010
QIDX
QDMA index register
0200 0014 − 0200 001C
18
REGISTER NAME
Reserved
0200 0020
QSOPT
QDMA pseudo options register
0200 0024
QSSRC
QDMA pseudo source address register
0200 0028
QSCNT
QDMA pseudo frame count register
0200 002C
QSDST
QDMA pseudo destination address register
0200 0030
QSIDX
QDMA pseudo index register
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
COMMENTS
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 10. Interrupt Selector Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
019C 0000
MUXH
Interrupt multiplexer high
Selects which interrupts drive CPU
interrupts 10−15 (INT10−INT15)
019C 0004
MUXL
Interrupt multiplexer low
Selects which interrupts drive CPU
interrupts 4−9 (INT04−INT09)
019C 0008
EXTPOL
External interrupt polarity
Sets the polarity of the external
interrupts (EXT_INT4−EXT_INT7)
019C 000C − 019C 01FF
−
Reserved
Table 11. McBSP 0 Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
018C 0000
DRR0
McBSP0 data receive register via Configuration Bus
0x3000 0000 − 0x33FF FFFF
DRR0
McBSP0 data receive register via Peripheral Bus
018C 0004
DXR0
McBSP0 data transmit register via Configuration Bus
0x3000 0000 − 0x33FF FFFF
DXR0
McBSP0 data transmit register via Peripheral Bus
018C 0008
SPCR0
018C 000C
RCR0
McBSP0 receive control register
018C 0010
XCR0
McBSP0 transmit control register
018C 0014
SRGR0
COMMENTS
The CPU and EDMA controller
can only read this register;
they cannot write to it.
McBSP0 serial port control register
McBSP0 sample rate generator register
018C 0018
MCR0
018C 001C
RCERE00
McBSP0 multichannel control register
McBSP0 enhanced receive channel enable register 0
018C 0020
XCERE00
McBSP0 enhanced transmit channel enable register 0
018C 0024
PCR0
018C 0028
RCERE10
McBSP0 enhanced receive channel enable register 1
018C 002C
XCERE10
McBSP0 enhanced transmit channel enable register 1
018C 0030
RCERE20
McBSP0 enhanced receive channel enable register 2
018C 0034
XCERE20
McBSP0 enhanced transmit channel enable register 2
McBSP0 pin control register
018C 0038
RCERE30
McBSP0 enhanced receive channel enable register 3
018C 003C
XCERE30
McBSP0 enhanced transmit channel enable register 3
018C 0040 − 018F FFFF
–
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
19
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 12. McBSP 1 Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
0190 0000
DRR1
McBSP1 data receive register via Configuration Bus
0x3400 0000 − 0x37FF FFFF
DRR1
McBSP1 data receive register via Peripheral Bus
0190 0004
DXR1
McBSP1 data transmit register via Configuration Bus
0x3400 0000 − 0x37FF FFFF
DXR1
McBSP1 data transmit register via Peripheral Bus
0190 0008
SPCR1
0190 000C
RCR1
McBSP1 receive control register
0190 0010
XCR1
McBSP1 transmit control register
0190 0014
SRGR1
COMMENTS
The CPU and EDMA controller
can only read this register;
they cannot write to it.
McBSP1 serial port control register
McBSP1 sample rate generator register
0190 0018
MCR1
0190 001C
RCERE01
McBSP1 multichannel control register
McBSP1 enhanced receive channel enable register 0
0190 0020
XCERE01
McBSP1 enhanced transmit channel enable register 0
0190 0024
PCR1
0190 0028
RCERE11
McBSP1 enhanced receive channel enable register 1
0190 002C
XCERE11
McBSP1 enhanced transmit channel enable register 1
0190 0030
RCERE21
McBSP1 enhanced receive channel enable register 2
0190 0034
XCERE21
McBSP1 enhanced transmit channel enable register 2
McBSP1 pin control register
0190 0038
RCERE31
McBSP1 enhanced receive channel enable register 3
0190 003C
XCERE31
McBSP1 enhanced transmit channel enable register 3
0190 0040 − 0193 FFFF
–
Reserved
Table 13. McBSP 2 Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
01A4 0000
DRR2
McBSP2 data receive register via Configuration Bus
0x3800 0000 − 0x3BFF FFFF
DRR2
McBSP2 data receive register via Peripheral Bus
01A4 0004
DXR2
McBSP2 data transmit register via Configuration Bus
0x3800 0000 − 0x3BFF FFFF
DXR2
McBSP2 data transmit register via Peripheral Bus
01A4 0008
SPCR2
01A4 000C
RCR2
McBSP2 receive control register
01A4 0010
XCR2
McBSP2 transmit control register
01A4 0014
SRGR2
20
McBSP2 serial port control register
McBSP2 sample rate generator register
01A4 0018
MCR2
01A4 001C
RCERE02
McBSP2 multichannel control register
McBSP2 enhanced receive channel enable register 0
01A4 0020
XCERE02
McBSP2 enhanced transmit channel enable register 0
01A4 0024
PCR2
01A4 0028
RCERE12
McBSP2 enhanced receive channel enable register 1
01A4 002C
XCERE12
McBSP2 enhanced transmit channel enable register 1
01A4 0030
RCERE22
McBSP2 enhanced receive channel enable register 2
01A4 0034
XCERE22
McBSP2 enhanced transmit channel enable register 2
McBSP2 pin control register
01A4 0038
RCERE32
McBSP2 enhanced receive channel enable register 3
01A4 003C
XCERE32
McBSP2 enhanced transmit channel enable register 3
01A4 0040 − 01A7 FFFF
–
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
COMMENTS
The CPU and EDMA controller
can only read this register;
they cannot write to it.
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 14. Timer 0 Registers
HEX ADDRESS RANGE
ACRONYM
0194 0000
CTL0
REGISTER NAME
COMMENTS
Timer 0 control register
Determines the operating
mode of the timer, monitors the
timer status, and controls the
function of the TOUT pin.
0194 0004
PRD0
Timer 0 period register
Contains the number of timer
input clock cycles to count.
This number controls the
TSTAT signal frequency.
0194 0008
CNT0
Timer 0 counter register
Contains the current value of
the incrementing counter.
0194 000C − 0197 FFFF
−
Reserved
Table 15. Timer 1 Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
0198 0000
CTL1
Timer 1 control register
Determines the operating
mode of the timer, monitors the
timer status, and controls the
function of the TOUT pin.
0198 0004
PRD1
Timer 1 period register
Contains the number of timer
input clock cycles to count.
This number controls the
TSTAT signal frequency.
0198 0008
CNT1
Timer 1 counter register
Contains the current value of
the incrementing counter.
0198 000C − 019B FFFF
−
Reserved
Table 16. Timer 2 Registers
HEX ADDRESS RANGE
01AC 0000
ACRONYM
CTL2
REGISTER NAME
COMMENTS
Timer 2 control register
Determines the operating
mode of the timer, monitors the
timer status, and controls the
function of the TOUT pin.
01AC 0004
PRD2
Timer 2 period register
Contains the number of timer
input clock cycles to count.
This number controls the
TSTAT signal frequency.
01AC 0008
CNT2
Timer 2 counter register
Contains the current value of
the incrementing counter.
01AC 000C − 01AF FFFF
−
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
21
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 17. HPI Registers
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
COMMENTS
−
HPID
HPI data register
Host read/write access only
0188 0000
HPIC
HPI control register
HPIC has both Host/CPU
read/write access
0188 0004
HPIA
(HPIAW)†
HPI address register (Write)
0188 0008
HPIA
(HPIAR)†
HPI address register (Read)
0188 000C − 0189 FFFF
−
018A 0000
TRCTL
018A 0004 − 018B FFFF
−
HPIA has both Host/CPU
read/write access
Reserved
HPI transfer request control register
Reserved
† Host access to the HPIA register updates both the HPIAW and HPIAR registers. The CPU can access HPIAW and HPIAR independently.
Table 18. GPIO Registers
22
HEX ADDRESS RANGE
ACRONYM
01B0 0000
GPEN
GPIO enable register
REGISTER NAME
01B0 0004
GPDIR
GPIO direction register
01B0 0008
GPVAL
GPIO value register
01B0 000C
−
01B0 0010
GPDH
GPIO delta high register
01B0 0014
GPHM
GPIO high mask register
01B0 0018
GPDL
GPIO delta low register
01B0 001C
GPLM
GPIO low mask register
01B0 0020
GPGC
GPIO global control register
01B0 0024
GPPOL
GPIO interrupt polarity register
01B0 0028 − 01B0 01FF
−
01B0 0200
DEVICE_REV
01B0 0204 − 01B3 FFFF
−
Reserved
Reserved
Silicon Revision Identification Register
(For more details, see the device characteristics listed in Table 1.)
Reserved
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 19. PCI Peripheral Registers (C6415 and C6416 Only)†
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
01C0 0000
RSTSRC
01C0 0004
−
01C0 0008
PCIIS
PCI interrupt source register
01C0 000C
PCIIEN
PCI interrupt enable register
01C0 0010
DSPMA
DSP master address register
01C0 0014
PCIMA
PCI master address register
01C0 0018
PCIMC
PCI master control register
01C0 001C
CDSPA
Current DSP address register
01C0 0020
CPCIA
Current PCI address register
01C0 0024
CCNT
Current byte count register
01C0 0028
−
Reserved
01C0 002C − 01C1 FFEF
–
Reserved
0x01C1 FFF0
HSR
0x01C1 FFF4
HDCR
Host-to-DSP control register
DSP page register
DSP Reset source/status register
Reserved
Host status register
0x01C1 FFF8
DSPP
0x01C1 FFFC
−
01C2 0000
EEADD
EEPROM address register
01C2 0004
EEDAT
EEPROM data register
01C2 0008
EECTL
EEPROM control register
01C2 000C − 01C2 FFFF
–
01C3 0000
TRCTL
01C3 0004 − 01C3 FFFF
–
Reserved
Reserved
PCI transfer request control register
Reserved
† These PCI registers are not supported on the C6414 device.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
23
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 20. UTOPIA (C6415 and C6416 Only)†
HEX ADDRESS RANGE
ACRONYM
REGISTER NAME
01B4 0000
UCR
01B4 0004
−
Reserved
01B4 0008
−
Reserved
01B4 000C
UIER
UTOPIA interrupt enable register
01B4 0010
UIPR
UTOPIA interrupt pending register
01B4 0014
CDR
Clock detect register
01B4 0018
EIER
Error interrupt enable register
01B4 001C
EIPR
Error interrupt pending register
01B4 0020 − 01B7 FFFF
−
UTOPIA control register
Reserved
† These UTOPIA registers are not supported on the C6414 device.
Table 21. UTOPIA QUEUES (C6415 and C6416 Only)†
HEX ADDRESS RANGE
ACRONYM
3C00 0000
URQ
UTOPIA receive queue
REGISTER NAME
3D00 0000
UXQ
UTOPIA transmit queue
3D00 0004 − 3FFF FFFF
−
Reserved
† These UTOPIA registers are not supported on the C6414 device.
24
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
peripheral register descriptions (continued)
Table 22. VCP Registers (C6416 Only)†
EDMA BUS
HEX ADDRESS RANGE
PERIPHERAL BUS
HEX ADDRESS RANGE
ACRONYM
5000 0000
01B8 0000
VCPIC0
VCP input configuration register 0
5000 0004
01B8 0004
VCPIC1
VCP input configuration register 1
5000 0008
01B8 0008
VCPIC2
VCP input configuration register 2
5000 000C
01B8 000C
VCPIC3
VCP input configuration register 3
5000 0010
01B8 0010
VCPIC4
VCP input configuration register 4
5000 0014
01B8 0014
VCPIC5
VCP input configuration register 5
5000 0040
01B8 0024
VCPOUT0
VCP output register 0
5000 0044
01B8 0028
VCPOUT1
VCP output register 1
5000 0080
−
VCPWBM
VCP branch metrics write register
5000 0088
−
VCPRDECS
−
01B8 0018
VCPEXE
VCP execution register
−
01B8 0020
VCPEND
VCP endian register
−
01B8 0040
VCPSTAT0
VCP status register 0
−
01B8 0044
VCPSTAT1
VCP status register 1
−
01B8 0050
VCPERR
REGISTER NAME
VCP decisions read register
VCP error register
† These VCP registers are supported on the C6416 device only.
Table 23. TCP Registers (C6416 Only)‡
EDMA BUS
HEX ADDRESS RANGE
PERIPHERAL BUS
HEX ADDRESS RANGE
ACRONYM
5800 0000
01BA 0000
TCPIC0
TCP input configuration register 0
5800 0004
01BA 0004
TCPIC1
TCP input configuration register 1
5800 0008
01BA 0008
TCPIC2
TCP input configuration register 2
5800 000C
01BA 000C
TCPIC3
TCP input configuration register 3
5800 0010
01BA 0010
TCPIC4
TCP input configuration register 4
5800 0014
01BA 0014
TCPIC5
TCP input configuration register 5
5800 0018
01BA 0018
TCPIC6
TCP input configuration register 6
5800 001C
01BA 001C
TCPIC7
TCP input configuration register 7
5800 0020
01BA 0020
TCPIC8
TCP input configuration register 8
5800 0024
01BA 0024
TCPIC9
TCP input configuration register 9
5800 0028
01BA 0028
TCPIC10
TCP input configuration register 10
5800 002C
01BA 002C
TCPIC11
TCP input configuration register 11
5800 0030
01BA 0030
TCPOUT
TCP output parameters register
5802 0000
−
TCPSP
5804 0000
−
TCPEXT
5806 0000
−
TCPAP
5808 0000
−
TCPINTER
REGISTER NAME
TCP systematics and parities memory
TCP extrinsic memory
TCP apriori memory
TCP interleaver memory
580A 0000
−
TCPHD
TCP hard decisions memory
−
01BA 0038
TCPEXE
TCP execution register
−
01BA 0040
TCPEND
TCP endian register
−
01BA 0050
TCPERR
TCP error register
−
01BA 0058
TCPSTAT
TCP status register
‡ These TCP registers are supported on the C6416 device only.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
25
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
EDMA channel synchronization events
The C64x EDMA supports up to 64 EDMA channels which service peripheral devices and external memory.
Table 24 lists the source of C64x EDMA synchronization events associated with each of the programmable
EDMA channels. For the C64x device, the association of an event to a channel is fixed; each of the EDMA
channels has one specific event associated with it. These specific events are captured in the EDMA event
registers (ERL, ERH) even if the events are disabled by the EDMA event enable registers (EERL, EERH). The
priority of each event can be specified independently in the transfer parameters stored in the EDMA parameter
RAM. For more detailed information on the EDMA module and how EDMA events are enabled, captured,
processed, linked, chained, and cleared, etc., see the TMS320C6000 DSP Enhanced Direct Memory Access
(EDMA) Controller Reference Guide (literature number SPRU234).
26
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
EDMA channel synchronization events (continued)
Table 24. SMJ320C64x EDMA Channel Synchronization Events†
EDMA
CHANNEL
EVENT NAME
0
DSP_INT
1
TINT0
Timer 0 interrupt
2
TINT1
Timer 1 interrupt
3
SD_INTA
4
GPINT4/EXT_INT4
GPIO event 4/External interrupt pin 4
5
GPINT5/EXT_INT5
GPIO event 5/External interrupt pin 5
6
GPINT6/EXT_INT6
GPIO event 6/External interrupt pin 6
7
GPINT7/EXT_INT7
GPIO event 7/External interrupt pin 7
8
GPINT0
GPIO event 0
9
GPINT1
GPIO event 1
10
GPINT2
GPIO event 2
11
GPINT3
GPIO event 3
12
XEVT0
McBSP0 transmit event
13
REVT0
McBSP0 receive event
14
XEVT1
McBSP1 transmit event
15
REVT1
McBSP1 receive event
16
–
17
XEVT2
McBSP2 transmit event
18
REVT2
McBSP2 receive event
19
TINT2
Timer 2 interrupt
20
SD_INTB
EMIFB SDRAM timer interrupt
21
–
Reserved, for future expansion
22−27
–
None
28
VCPREVT
29
VCPXEVT
30
TCPREVT
31
TCPXEVT
32
UREVT
EVENT DESCRIPTION
HPI/PCI-to-DSP interrupt (PCI peripheral supported on C6415 and C6416 only)‡
EMIFA SDRAM timer interrupt
None
VCP receive event (C6416 only)§
VCP transmit event (C6416 only)§
TCP receive event (C6416 only)§
TCP transmit event (C6416 only)§
UTOPIA receive event (C6415 and C6416 only)‡
33−39
–
40
UXEVT
None
41−47
–
48
GPINT8
GPIO event 8
49
GPINT9
GPIO event 9
50
GPINT10
GPIO event 10
51
GPINT11
GPIO event 11
52
GPINT12
GPIO event 12
53
GPINT13
GPIO event 13
54
GPINT14
GPIO event 14
55
GPINT15
GPIO event 15
56−63
–
UTOPIA transmit event (C6415 and C6416 only)‡
None
None
† In addition to the events shown in this table, each of the 64 channels can also be synchronized with the transfer completion or alternate transfer
completion events. For more detailed information on EDMA event-transfer chaining, see the TMS320C6000 DSP Enhanced Direct Memory
Access (EDMA) Controller Reference Guide (literature number SPRU234).
‡ The PCI and UTOPIA peripherals are not supported on the C6414 device; therefore, these EDMA synchronization events are reserved.
§ The VCP/TCP EDMA synchronization events are supported on the C6416 only. For the C6414 and C6415 devices, these events are reserved.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
27
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
interrupt sources and interrupt selector
The C64x DSP core supports 16 prioritized interrupts, which are listed in Table 25. The highest-priority interrupt
is INT_00 (dedicated to RESET) while the lowest-priority interrupt is INT_15. The first four interrupts
(INT_00−INT_03) are non-maskable and fixed. The remaining interrupts (INT_04−INT_15) are maskable and
default to the interrupt source specified in Table 25. The interrupt source for interrupts 4−15 can be programmed
by modifying the selector value (binary value) in the corresponding fields of the Interrupt Selector Control
registers: MUXH (address 0x019C0000) and MUXL (address 0x019C0004).
28
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
interrupt sources and interrupt selector (continued)
Table 25. C64x DSP Interrupts
INTERRUPT
SELECTOR
CONTROL
REGISTER
SELECTOR
VALUE
(BINARY)
INTERRUPT
EVENT
INT_00†
INT_01†
−
−
RESET
−
−
NMI
INT_02†
INT_03†
−
−
Reserved
Reserved. Do not use.
−
−
Reserved
Reserved. Do not use.
INT_04‡
INT_05‡
MUXL[4:0]
00100
GPINT4/EXT_INT4
GPIO interrupt 4/External interrupt pin 4
MUXL[9:5]
00101
GPINT5/EXT_INT5
GPIO interrupt 5/External interrupt pin 5
INT_06‡
INT_07‡
MUXL[14:10]
00110
GPINT6/EXT_INT6
GPIO interrupt 6/External interrupt pin 6
MUXL[20:16]
00111
GPINT7/EXT_INT7
GPIO interrupt 7/External interrupt pin 7
INT_08‡
INT_09‡
MUXL[25:21]
01000
EDMA_INT
EDMA channel (0 through 63) interrupt
MUXL[30:26]
01001
EMU_DTDMA
INT_10‡
MUXH[4:0]
00011
SD_INTA
INT_11‡
MUXH[9:5]
01010
EMU_RTDXRX
EMU real-time data exchange (RTDX)
receive
INT_12‡
MUXH[14:10]
01011
EMU_RTDXTX
EMU RTDX transmit
INT_13‡
MUXH[20:16]
00000
DSP_INT
INT_14‡
INT_15‡
MUXH[25:21]
00001
TINT0
Timer 0 interrupt
MUXH[30:26]
00010
TINT1
Timer 1 interrupt
−
−
01100
XINT0
McBSP0 transmit interrupt
−
−
01101
RINT0
McBSP0 receive interrupt
−
−
01110
XINT1
McBSP1 transmit interrupt
−
−
01111
RINT1
McBSP1 receive interrupt
−
−
10000
GPINT0
−
−
10001
XINT2
McBSP2 transmit interrupt
−
−
10010
RINT2
McBSP2 receive interrupt
−
−
10011
TINT2
Timer 2 interrupt
−
−
10100
SD_INTB
EMIFB SDRAM timer interrupt
−
−
10101
Reserved
Reserved. Do not use.
−
−
10110
Reserved
Reserved. Do not use.
−
−
10111
UINT
−
−
11000 − 11101
Reserved
−
−
11110
VCPINT
VCP interrupt (C6416 only)
−
−
11111
TCPINT
TCP interrupt (C6416 only)
CPU
INTERRUPT
NUMBER
INTERRUPT SOURCE
EMU DTDMA
EMIFA SDRAM timer interrupt
HPI/PCI-to-DSP interrupt
(PCI supported on C6415 and C6416 only)
GPIO interrupt 0
UTOPIA interrupt (C6415/C6416 only)
Reserved. Do not use.
† Interrupts INT_00 through INT_03 are non-maskable and fixed.
‡ Interrupts INT_04 through INT_15 are programmable by modifying the binary selector values in the Interrupt Selector Control
registers fields. Table 25 shows the default interrupt sources for Interrupts INT_04 through INT_15. For more detailed
information on interrupt sources and selection, see the TMS320C6000 DSP Interrupt Selector Reference Guide (literature
number SPRU646).
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
29
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
signal groups description
CLKIN
CLKOUT4/GP1†
CLKOUT6/GP2†
CLKMODE1
CLKMODE0
PLLV
TMS
TDO
TDI
TCK
TRST
EMU0
EMU1
EMU2
EMU3
EMU4
EMU5
EMU6
EMU7
EMU8
EMU9
EMU10
EMU11
Reset and
Interrupts
Clock/PLL
Reserved
IEEE Standard
1149.1
(JTAG)
Emulation
RESET
NMI
GP7/EXT_INT7‡
GP6/EXT_INT6‡
GP5/EXT_INT5‡
GP4/EXT_INT4‡
RSV
RSV
RSV
RSV
RSV
RSV
•
•
•
RSV
RSV
RSV
Peripheral
Control/Status
PCI_EN
MCBSP2_EN
Control/Status
GP15/PRST§
GP14/PCLK§
GP13/PINTA§
GP12/PGNT§
GP11/PREQ§
GP10/PCBE3§
GP9/PIDSEL§
CLKS2/GP8†
GPIO
GP7/EXT_INT7‡
GP6/EXT_INT6‡
GP5/EXT_INT5‡
GP4/EXT_INT4‡
GP3
CLKOUT6/GP2†
CLKOUT4/GP1†
GP0
General-Purpose Input/Output (GPIO) Port
† These pins are MUXed with the GPIO port pins and by default these signals function as clocks (CLKOUT4 or CLKOUT6) or McBSP2
clock source (CLKS2). To use these MUXed pins as GPIO signals, the appropriate GPIO register bits (GPxEN and GPxDIR) must be
properly enabled and configured. For more details, see the Device Configurations section of this data sheet.
‡ These pins are GPIO pins that can also function as external interrupt sources (EXT_INT[7:4]). Default after reset is EXT_INTx or
GPIO as input-only.
§ For the C6415 and C6416 devices, these GPIO pins are MUXed with the PCI peripheral pins. By default, these signals are set up to
no function with both the GPIO and PCI pin functions disabled. For more details on these MUXed pins, see the Device
Configurations section of this data sheet. For the C6414 device, the GPIO peripheral pins are not MUXed; the C6414 device does
not support the PCI peripheral.
Figure 2. CPU and Peripheral Signals
30
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
signal groups description (continued)
64
Data
AED[63:0]
AECLKIN
ACE3
ACE2
Memory Map
Space Select
ACE1
ACE0
20
AEA[22:3]
External
Memory I/F
Control
Address
ABE7
ABE6
ABE5
ABE4
Byte Enables
ABE3
ABE2
ABE1
ABE0
Bus
Arbitration
AECLKOUT1
AECLKOUT2
ASDCKE
AARE/ASDCAS/ASADS/ASRE
AAOE/ASDRAS/ASOE
AAWE/ASDWE/ASWE
AARDY
ASOE3
APDT
AHOLD
AHOLDA
ABUSREQ
EMIFA (64-bit)†
16
Data
BED[15:0]
BECLKIN
BECLKOUT1
BECLKOUT2
BCE3
BCE2
BCE1
BCE0
Memory Map
Space Select
External
Memory I/F
Control
20
BEA[20:1]
BBE1
BBE0
BARE/BSDCAS/BSADS/BSRE
BAOE/BSDRAS/BSOE
BAWE/BSDWE/BSWE
BARDY
BSOE3
BPDT
Address
Byte Enables
Bus
Arbitration
BHOLD
BHOLDA
BBUSREQ
EMIFB (16-bit)†
† These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is
an EMIFA signal whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document,
in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted from the signal name.
Figure 3. Peripheral Signals
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
31
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
signal groups description (continued)
32
HPI†
(Host-Port Interface)
Data
HD[31:0]/AD[31:0]
HCNTL0/PSTOP
HCNTL1/PDEVSEL
Register Select
Control
Half-Word
Select
HHWIL/PTRDY
(HPI16 ONLY)
HAS/PPAR
HR/W/PCBE2
HCS/PPERR
HDS1/PSERR
HDS2/PCBE1
HRDY/PIRDY
HINT/PFRAME
32
HD[31:0]/AD[31:0]
GP10/PCBE3
HR/W/PCBE2
HDS2/PCBE1
PCBE0§
GP12/PGNT
Data/Address
Clock
Command
Byte Enable
Control
Arbitration
Error
GP11/PREQ
Serial
EEPROM
PCI Interface‡
(C6415 and C6416 Only)
GP14/PCLK
GP9/PIDSEL
HCNTL1/PDEVSEL
HINT/PFRAME
GP13/PINTA
HAS/PPAR
GP15/PRST
HRDY/PIRDY
HCNTL0/PSTOP
HHWIL/PTRDY
HDS1/PSERR
HCS/PPERR
DX2/XSP_DO
XSP_CS§
CLKX2/XSP_CLK
DR2/XSP_DI
† For the C6415 and C6416 devices, these HPI pins are MUXed with the PCI peripheral. By default, these signals function as HPI. For
more details on these MUXed pins, see the Device Configurations section of this data sheet. For the C6414 device, these HPI pins are
not MUXed; the C6414 device does not support the PCI peripheral.
‡ For the C6415 and C6416 devices, these PCI pins (excluding PCBE0 and XSP_CS) are MUXed with the HPI, McBSP2, or GPIO
peripherals. By default, these signals function as HPI, McBSP2, and no function, respectively. For more details on these MUXed pins,
see the Device Configurations section of this data sheet. For the C6414 device, the HPI, McBSP2, and GPIO peripheral pins are not
MUXed; the C6414 device does not support the PCI peripheral.
§ For the C6414 device, these pins are “Reserved (leave unconnected, do not connect to power or ground).”
Figure 3. Peripheral Signals (Continued)
32
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
signal groups description (continued)
McBSP1
McBSP0
CLKX1/URADDR4†
FSX1/UXADDR3†
DX1/UXADDR4†
Transmit
Transmit
CLKR1/URADDR2†
FSR1/UXADDR2†
DR1/UXADDR1†
Receive
Receive
CLKS1/URADDR3†
Clock
CLKX0
FSX0
DX0
CLKR0
FSR0
DR0
Clock
CLKS0
McBSP2
CLKX2/XSP_CLK†
FSX2
DX2/XSP_DO†
Transmit
CLKR2
FSR2
DR2/XSP_DI†
Receive
CLKS2/GP8‡
Clock
McBSPs
(Multichannel Buffered
Serial Ports)
† For the C6415 and C6416 devices, these McBSP2 and McBSP1 pins are MUXed with the PCI and UTOPIA peripherals, respectively.
By default, these signals function as McBSP2 and McBSP1, respectively. For more details on these MUXed pins, see the Device
Configurations section of this data sheet.
For the C6414 device, these McBSP2 and McBSP1 peripheral pins are not MUXed; the C6414 device does not support PCI and
UTOPIA peripherals.
‡ The McBSP2 clock source pin (CLKS2, default) is MUXed with the GP8 pin. To use this MUXed pin as the GP8 signal, the appropriate
GPIO register bits (GP8EN and GP8DIR) must be properly enabled and configured. For more details, see the Device Configurations
section of this data sheet.
Figure 3. Peripheral Signals (Continued)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
33
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
signal groups description (continued)
UTOPIA (SLAVE) [C6415 and C6416 Only]
URDATA7
URDATA6
URDATA5
URDATA4
URDATA3
URDATA2
Receive
Transmit
URDATA1
URDATA0
URENB
CLKX1/URADDR4†
CLKS1/URADDR3†
CLKR1/URADDR2†
URADDR1
URADDR0
URCLAV
URSOC
UXDATA7
UXDATA6
UXDATA5
UXDATA4
UXDATA3
UXDATA2
UXDATA1
UXDATA0
Control/Status
Control/Status
UXENB
DX1/UXADDR4†
FSX1/UXADDR3†
FSR1/UXADDR2†
DR1/UXADDR1†
UXADDR0
UXCLAV
UXSOC
URCLK
Clock
TOUT1
TINP1
Timer 1
TOUT2
TINP2
Timer 2
Clock
Timer 0
UXCLK
TOUT0
TINP0
Timers
† For the C6415 and C6416 devices, these UTOPIA pins are MUXed with the McBSP1 peripheral. By default, these signals function as
McBSP1. For more details on these MUXed pins, see the Device Configurations section of this data sheet.
For the C6414 device, these McBSP1 peripheral pins are not MUXed; the C6414 does not support the UTOPIA peripheral.
Figure 3. Peripheral Signals (Continued)
34
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
DEVICE CONFIGURATIONS
The C6414, C6415, and C6416 peripheral selections and other device configurations are determined by
external pullup/pulldown resistors on the following pins (all of which are latched during device reset):
peripherals selection (C6415 and C6416 devices)
−
BEA11 (UTOPIA_EN)
−
PCI_EN (for C6415 or C6416, see Table 27 footnotes)
−
MCBSP2_EN (for C6414 or C6416, see Table 27 footnotes)
The C6414 device does not support the PCI and UTOPIA peripherals; for proper operation of the C6414
device, do not oppose the internal pulldowns (IPDs) on the BEA11, PCI_EN, and MCBSP2_EN pins. (For
IPUs/IPDs on pins, see the Terminal Functions table of this data sheet.)
other device configurations (C64x)
−
BEA[20:13, 7]
−
HD5
peripherals selection
Some C6415/C6416 peripherals share the same pins (internally MUXed) and are mutually exclusive (i.e., HPI,
general-purpose input/output pins GP[15:9], PCI and its internal EEPROM, McBSP1, McBSP2, and UTOPIA).
The VCP/TCP coprocessors (C6416 only) and other C64x peripherals (i.e., the Timers, McBSP0, and the
GP[8:0] pins), are always available.
UTOPIA and McBSP1 peripherals
The UTOPIA_EN pin (BEA11) is latched at reset. For C6415 and C6416 devices, this pin selects whether
the UTOPIA peripheral or McBSP1 peripheral is functionally enabled (see Table 26).
The C6414 device does not support the UTOPIA peripheral; for proper device operation, do not oppose the
internal pulldown (IPD) on the BEA11 pin.
Table 26. UTOPIA_EN Peripheral Selection (McBSP1 and UTOPIA) (C6415/C6416 Only)
PERIPHERAL SELECTION
UTOPIA_EN
(BEA11) Pin [F14]
PERIPHERALS SELECTED
UTOPIA
√
0
1
√
DESCRIPTION
McBSP1
McBSP1 is enabled and UTOPIA is disabled [default].
This means all multiplexed McBSP1/UTOPIA pins function as McBSP1
and all other standalone UTOPIA pins are tied-off (Hi-Z).
UTOPIA is enabled and McBSP1 is disabled.
This means all multiplexed McBSP1/UTOPIA pins now function as
UTOPIA and all other standalone McBSP1 pins are tied-off (Hi-Z).
HPI, GP[15:9], PCI, EEPROM (internal to PCI), and McBSP2 peripherals
The PCI_EN and MCBSP2_EN pins are latched at reset. They determine specific peripheral selection for
the C6415 and C6416 devices, summarized in Table 27.
The C6414 device does not support the PCI peripheral; for proper device operation, do not oppose the
internal pulldowns (IPDs) on the PCI_EN and MCBSP2_EN pins.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
35
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
DEVICE CONFIGURATIONS (CONTINUED)
Table 27. PCI_EN and MCBSP2_EN Peripheral Selection (HPI, GP[15:9], PCI, and McBSP2)
PERIPHERAL SELECTION†
PERIPHERALS SELECTED
PCI_EN
Pin [T8]
MCBSP2_EN
Pin [AB4]
HPI
GP[15:9]
0
0
√
√
√
0
1
√
√
1
0
√
‡
PCI
√
EEPROM
(Internal to PCI)
√
McBSP2
√
† The PCI_EN pin must be driven valid at all times and the user must not switch values throughout device operation.
The MCBSP2_EN pin must be driven valid at all times and the user can switch values throughout device operation.
‡ The only time McBSP2 is disabled is when both PCI_EN = 1 and MCBSP2_EN = 0. This configuration enables, at reset, the auto-initialization
of the PCI peripheral through the PCI internal EEPROM [provided the PCI EEPROM Auto-Initialization pin (BEA13) is pulled up
(EEAI = 1)]. The user can then enable the McBSP2 peripheral (disabling EEPROM) by dynamically changing MCBSP2_EN to a “1” after the
device is initialized (out of reset).
1
√
1
−
If the PCI is disabled (PCI_EN = 0), the HPI peripheral is enabled and GP[15:9] pins can be programmed
as GPIO, provided the GPxEN and GPxDIR bits are properly configured.
This means all multiplexed HPI/PCI pins function as HPI and all standalone PCI pins (PCBE0 and
XSP_CS) are tied-off (Hi-Z). Also, the multiplexed GPIO/PCI pins can be used as GPIO with the
proper software configuration of the GPIO enable and direction registers (for more details, see
Table 29).
−
If the PCI is enabled (PCI_EN = 1), the HPI peripheral is disabled.
This means all multiplexed HPI/PCI pins function as PCI. Also, the multiplexed GPIO/PCI pins function
as PCI pins (for more details, see Table 29).
−
The MCBSP2_EN pin, in combination with the PCI_EN pin, controls the selection of the McBSP2
peripheral and the PCI internal EEPROM (for more details, see Table 27 and its footnotes).
other device configurations
Table 28 describes the C6414, C6415, and C6416 devices configuration pins, which are set up via external
pullup/pulldown resistors through the specified EMIFB address bus pins (BEA[20:13, 11, 9:7]) and the HD5 pin.
For more details on these device configuration pins, see the Terminal Functions table and the Debugging
Considerations section.
36
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
DEVICE CONFIGURATIONS (CONTINUED)
Table 28. Device Configuration Pins (BEA[20:13, 9:7], HD5, and BEA11)
CONFIGURATION
PIN
NO.
BEA20
E15
BEA[19:18]
BEA[17:16]
BEA[15:14]
BEA13
FUNCTIONAL DESCRIPTION
Device Endian mode (LEND)
0 – System operates in Big Endian mode
1 − System operates in Little Endian mode (default)
[D17,
J14]
Bootmode [1:0]
00 – No boot
01 − HPI boot
10 − EMIFB 8-bit ROM boot with default timings (default mode)
11 − Reserved
[E16,
G15]
EMIFA input clock select
Clock mode select for EMIFA (AECLKIN_SEL[1:0])
00 – AECLKIN (default mode)
01 − CPU/4 Clock Rate
10 − CPU/6 Clock Rate
11 − Reserved
[C18,
F15]
EMIFB input clock select
Clock mode select for EMIFB (BECLKIN_SEL[1:0])
00 – BECLKIN (default mode)
01 − CPU/4 Clock Rate
10 − CPU/6 Clock Rate
11 − Reserved
D16
PCI EEPROM Auto-Initialization (EEAI) [C6415 and C6416 devices only]
[The C6414 device does not support the PCI peripheral; for proper device operation, do not oppose the
internal pulldown (IPD) on the BEA13 pin.]
PCI auto-initialization via external EEPROM
0 − PCI auto-initialization through EEPROM is disabled; the PCI peripheral uses the specified
PCI default values (default).
1 − PCI auto-initialization through EEPROM is enabled; the PCI peripheral is configured
through EEPROM provided the PCI peripheral pin is enabled (PCI_EN = 1) and the
McBSP2 peripheral pin is disabled (MCBSP2_EN = 0).
Note: If the PCI peripheral is disabled (PCI_EN pin = 0), this pin must not be pulled up.
For more information on the PCI EEPROM default values, see the TMS320C6000 DSP Peripheral
Component Interconnect (PCI) Reference Guide (literature number SPRU581).
UTOPIA Enable (UTOPIA_EN) [C6415 and C6416 devices only]
[The C6414 device does not support the UTOPIA peripheral; for proper device operation, do not
oppose the internal pulldown (IPD) on the BEA11 pin.]
UTOPIA peripheral enable (functional)
BEA11
F14
0 − UTOPIA peripheral disabled (McBSP1 functions are enabled). [default]
This means all multiplexed McBSP1/UTOPIA pins function as McBSP1 and all other
standalone UTOPIA pins are tied-off (Hi-Z).
1 − UTOPIA peripheral enabled (McBSP1 functions are disabled).
This means all multiplexed McBSP1/UTOPIA pins now function as UTOPIA and all other
standalone McBSP1 pins are tied-off (Hi-Z).
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
37
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
DEVICE CONFIGURATIONS (CONTINUED)
Table 28. Device Configuration Pins (BEA[20:13, 9:7], HD5, and BEA11) (Continued)
CONFIGURATION
PIN
NO.
FUNCTIONAL DESCRIPTION
C6414 Devices
BEA7
BEA8
BEA9
E14
G14
G13
C6415 Devices
Do not oppose internal pulldown (IPD) Pullup†
Do not oppose IPD
Do not oppose IPD
Do not oppose IPD
Do not oppose IPD
C6416 Devices
Do not oppose IPD
Pullup†
Pullup†
†For proper device operation, this pin must be externally pulled up with a 1-kΩ resistor.
HD5
38
U4
HPI peripheral bus width (HPI_WIDTH)
0 − HPI operates as an HPI16.
(HPI bus is 16 bits wide. HD[15:0] pins are used and the remaining HD[31:16] pins are
reserved pins in the Hi-Z state.)
1 − HPI operates as an HPI32.
(HPI bus is 32 bits wide. All HD[31:0] pins are used for host-port operations.)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
DEVICE CONFIGURATIONS (CONTINUED)
multiplexed pins
Multiplexed pins are pins that are shared by more than one peripheral and are internally multiplexed. Some of
these pins are configured by software, and the others are configured by external pullup/pulldown resistors only
at reset. Those MUXed pins that are configured by software can be programmed to switch functionalities at any
time. Those MUXed pins that are configured by external pullup/pulldown resistors are mutually exclusive; only
one peripheral has primary control of the function of these pins after reset. Table 29 identifies the multiplexed
pins on the C6414, C6415, and C6416 devices; shows the default (primary) function and the default settings
after reset; and describes the pins, registers, etc. necessary to configure specific multiplexed functions.
debugging considerations
It is recommended that external connections be provided to device configuration pins, including
CLKMODE[1:0], BEA[20:13, 11, 9:7], HD5/AD5, PCI_EN, and MCBSP2_EN. Although internal pullup/pulldown
resistors exist on these pins (except for HD5/AD5), providing external connectivity adds convenience to the user
in debugging and flexibility in switching operating modes.
Internal pullup/pulldown resistors also exist on the non-configuration pins on the BEA bus (BEA[12, 10, 6:1]).
Do not oppose the internal pullup/pulldown resistors on these non-configuration pins with external
pullup/pulldown resistors. If an external controller provides signals to these non-configuration pins, these
signals must be driven to the default state of the pins at reset, or not be driven at all.
For the internal pullup/pulldown resistors on the C6414, C6415, and C6416 device pins, see the terminal
functions table.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
39
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
DEVICE CONFIGURATIONS (CONTINUED)
Table 29. C6414, C6415, and C6416 Device Multiplexed Pins†
MULTIPLEXED PINS
NAME
NO.
DEFAULT FUNCTION
DEFAULT SETTING
CLKOUT4/GP1‡
Y7
CLKOUT4
GP1EN = 0 (disabled)
CLKOUT6/GP2‡
T10
CLKOUT6
GP2EN = 0 (disabled)
CLKS2/GP8‡
W7
CLKS2
GP8EN = 0 (disabled)
GP9/PIDSEL
K6
GP10/PCBE3
L7
GP11/PREQ
H6
GP12/PGNT
J7
GP13/PINTA
G4
GP14/PCLK
G5
GP15/PRST
None
Y10
DX1
FSX1/UXADDR3
AA11
FSX1
FSR1/UXADDR2
AA8
FSR1
DR1/UXADDR1
V11
DR1
CLKX1/URADDR4
T12
CLKX1
CLKS1/URADDR3
Y8
CLKS1
CLKR1/URADDR2
AB7
CLKR1
CLKX2/XSP_CLK
W5
CLKX2
DR2/XSP_DI
Y4
DR2
DX2/XSP_DO
DX2
HD[31:0]/AD[31:0]
R9
§
HAS/PPAR
N7
HAS
HCNTL1/PDEVSEL
N8
HCNTL1
HCNTL0/PSTOP
P5
HCNTL0
HDS1/PSERR
R5
HDS1
HDS2/PCBE1
P6
HDS2
HR/W/PCBE2
N6
HR/W
HWWIL/PTRDY
N5
HHWIL (HPI16 only)
HINT/PFRAME
P4
HINT
HCS/PPERR
N9
HCS
These pins are software-configurable.
To use these pins as GPIO pins, the
GPxEN bits in the GPIO Enable
Register and the GPxDIR bits in the
GPIO Direction Register must be
properly configured.
GPxEN = 1: GPx pin enabled
GPxDIR = 0: GPx pin is an input
GPxDIR = 1: GPx pin is an output
GPxEN = 0 (disabled)
PCI_EN = 0 (disabled)†
To use GP[15:9] as GPIO pins, the PCI
needs to be disabled (PCI_EN = 0), the
GPxEN bits in the GPIO Enable
Register and the GPxDIR bits in the
GPIO Direction Register must be
properly configured.
GPxEN = 1: GPx pin enabled
GPxDIR = 0: GPx pin is an input
GPxDIR = 1: GPx pin is an output
UTOPIA_EN (BEA11) = 0
(disabled)†
By default, McBSP1 is enabled upon
reset (UTOPIA is disabled).
To enable the UTOPIA peripheral, an
external pullup resistor (1 kΩ) must be
provided on the BEA11 pin (setting
UTOPIA_EN = 1 at reset).
PCI_EN = 0 (disabled)†
By default, HPI is enabled upon reset
(PCI is disabled).
To enable the PCI peripheral an external
pullup resistor (1 kkΩ)) must be provided
on the PCI_EN pin (setting PCI_EN = 1
at reset).
J8
DX1/UXADDR4
DESCRIPTION
HD[31:0]
HRDY/PIRDY
N4
HRDY
† For the C6415 and C6416 devices, all other standalone UTOPIA and PCI pins are tied-off internally (pins in Hi-Z) when the peripheral is disabled
[UTOPIA_EN (BEA11) = 0 or PCI_EN = 0].
‡ The C6414 device does not support the PCI and UTOPIA peripherals. These are the only multiplexed pins on the C6414 device, all other pins
are standalone peripheral functions and are not MUXed.
§ For the HD[31:0]/AD[31:0] multiplexed pins pin numbers, see the Terminal Functions table.
40
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
CLOCK/PLL CONFIGURATION
CLKIN
H4
I
IPD
Clock Input. This clock is the input to the on-chip PLL.
CLKOUT4/GP1§
Y7
I/O/Z
IPD
Clock output at 1/4 of the device speed (O/Z) [default] or this pin can be programmed as a
GPIO 1 pin (I/O/Z).
CLKOUT6/GP2§
T10
I/O/Z
IPD
Clock output at 1/6 of the device speed (O/Z) [default] or this pin can be programmed as a
GPIO 2 pin (I/O/Z).
CLKMODE1
K8
I
IPD
CLKMODE0
E3
I
IPD
PLLV¶
L9
A#
Clock mode select
• Selects whether the CPU clock frequency = input clock frequency x1 (Bypass), x6, or x12.
For more details on the CLKMODE pins and the PLL multiply factors, see the Clock PLL
section of this data sheet.
PLL voltage supply
JTAG EMULATION
TMS
V14
I
IPU
JTAG test-port mode select
TDO
W16
O/Z
IPU
JTAG test-port data out
TDI
AA17
I
IPU
JTAG test-port data in
TCK
Y15
I
IPU
JTAG test-port clock
TRST
Y14
I
IPD
JTAG test-port reset. For IEEE 1149.1 JTAG compatibility, see the IEEE 1149.1 JTAG
Compatibility Statement section of this data sheet.
EMU11
V15
I/O/Z
IPU
Emulation pin 11. Reserved for future use, leave unconnected.
EMU10
Y16
I/O/Z
IPU
Emulation pin 10. Reserved for future use, leave unconnected.
EMU9
T14
I/O/Z
IPU
Emulation pin 9. Reserved for future use, leave unconnected.
EMU8
U14
I/O/Z
IPU
Emulation pin 8. Reserved for future use, leave unconnected.
EMU7
AB18
I/O/Z
IPU
Emulation pin 7. Reserved for future use, leave unconnected.
EMU6
AA16
I/O/Z
IPU
Emulation pin 6. Reserved for future use, leave unconnected.
EMU5
W15
I/O/Z
IPU
Emulation pin 5. Reserved for future use, leave unconnected.
EMU4
AB17
I/O/Z
IPU
Emulation pin 4. Reserved for future use, leave unconnected.
EMU3
W14
I/O/Z
IPU
Emulation pin 3. Reserved for future use, leave unconnected.
EMU2
AA15
I/O/Z
IPU
Emulation pin 2. Reserved for future use, leave unconnected.
EMU1
EMU0
T13
V13
I/O/Z
IPU
Emulation [1:0] pins
• Select the device functional mode of operation
Operation
EMU[1:0]
00
Boundary Scan/Normal Mode (see Note)
01
Reserved
10
Reserved
11
Emulation/Normal Mode [default] (see the IEEE 1149.1 JTAG
Compatibility Statement section of this data sheet)
Normal mode refers to the DSPs normal operational mode, when the DSP is free running. The
DSP can be placed in normal operational mode when the EMU[1:0] pins are configured for
either Boundary Scan or Emulation.
Note: When the EMU[1:0] pins are configured for Boundary Scan mode, the internal pulldown
(IPD) on the TRST signal must not be opposed in order to operate in Normal mode.
For the Boundary Scan mode pulldown EMU[1:0] pins with a dedicated 1-kΩ resister.
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
§ These pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
¶ PLLV is not part of external voltage supply. See the Clock PLL section for information on how to connect this pin.
# A = Analog signal (PLL Filter)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
41
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
RESETS, INTERRUPTS, AND GENERAL-PURPOSE INPUT/OUTPUTS
RESET
AB5
I
NMI
E6
I
Device reset
GP7/EXT_INT7
Y6
GP6/EXT_INT6
V8
GP5/EXT_INT5
AA5
GP4/EXT_INT4
GP15/PRST§
GP14/PCLK§
GP13/PINTA§
G4
GPIO 13 pin (I/O/Z) or PCI interrupt A (O/Z). No function at default.
IPD
Nonmaskable interrupt, edge-driven (rising edge)
IPU
U9
General-purpose input/output (GPIO) pins (I/O/Z) or external interrupts (input only). The
default after reset setting is GPIO enabled as input-only.
• When these pins function as External Interrupts [by selecting the corresponding interrupt
enable register bit (IER.[7:4])], they are edge-driven and the polarity can be
independently selected via the External Interrupt Polarity Register bits (EXTPOL.[3:0]).
J8
General-purpose input/output (GPIO) 15 pin (I/O/Z) or PCI reset (I). No function at default.
G5
GPIO 14 pin (I/O/Z) or PCI clock (I). No function at default.
I/O/Z
GP12/PGNT§
GP11/PREQ§
J7
GPIO 12 pin (I/O/Z) or PCI bus grant (I). No function at default.
H6
GPIO 11 pin (I/O/Z) or PCI bus request (O/Z). No function at default.
GP10/PCBE3§
GP9/PIDSEL§
K6
L7
GPIO 10 pin (I/O/Z) or PCI command/byte enable 3 (I/O/Z). No function at default.
I/O/Z
GPIO 9 pin (I/O/Z) or PCI initialization device select (I). No function at default.
GP3
AA6
IPD
GPIO 3 pin (I/O/Z). The default after reset setting is GPIO 3 enabled as input-only.
GP0
W8
IPD
GPIO 0 pin.
The general-purpose I/O 0 pin (GPIO 0) (I/O/Z) can be programmed as GPIO 0 (input only)
[default] or as GPIO 0 (output only) pin or output as a general-purpose interrupt (GP0INT)
signal (output only).
CLKS2/GP8§¶
W7
I/O/Z
IPD
McBSP2 external clock source (CLKS2) [input only] [default] or this pin can be programmed as a GPIO 8 pin (I/O/Z).
CLKOUT6/GP2§¶
T10
I/O/Z
IPD
Clock output at 1/6 of the device speed (O/Z) [default] or this pin can be programmed as a
GPIO 2 pin (I/O/Z).
CLKOUT4/GP1§¶
Y7
I/O/Z
IPD
Clock output at 1/4 of the device speed (O/Z) [default] or this pin can be programmed as a
GPIO 1 pin (I/O/Z).
HOST-PORT INTERFACE (HPI) [C64x] or PERIPHERAL COMPONENT INTERCONNECT (PCI) [C6415 or C6416 devices only]
PCI_EN
T8
I
IPD
PCI enable pin. This pin controls the selection (enable/disable) of the HPI and GP[15:9], or
PCI peripherals (for the C6415 and C6416 devices). This pin works in conjunction with the
MCBSP2_EN pin to enable/disable other peripherals (for more details, see the Device Configurations section of this data sheet).
The C6414 device does not support the PCI peripheral; for proper device operation, do not
oppose the internal pulldown (IPD) on this pin.
HINT/PFRAME§
P4
I/O/Z
Host interrupt from DSP to host (O) [default] or PCI frame (I/O/Z)
HCNTL1/
PDEVSEL§
N8
I/O/Z
Host control − selects between control, address, or data registers (I) [default] or PCI device
select (I/O/Z).
HCNTL0/
PSTOP§
P5
I/O/Z
Host control − selects between control, address, or data registers (I) [default] or PCI stop
(I/O/Z)
HHWIL/PTRDY§
N5
I/O/Z
Host half-word select − first or second half-word (not necessarily high or low order)
[For HPI16 bus width selection only] (I) [default] or PCI target ready (I/O/Z)
HR/W/PCBE2§
N6
I/O/Z
Host read or write select (I) [default] or PCI command/byte enable 2 (I/O/Z)
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
§ For the C6415 and C6416 devices, these pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
The C6414 device does not support the PCI or UTOPIA peripherals; therefore, these MUXed peripheral pins are standalone peripheral functions
for this device.
¶ For the C6414 device, only these pins are multiplexed pins.
42
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
HOST-PORT INTERFACE (HPI) [C64x] or PERIPHERAL COMPONENT INTERCONNECT (PCI) [C6415 or C6416 devices only]
(CONTINUED)
HAS/PPAR§
N7
I/O/Z
Host address strobe (I) [default] or PCI parity (I/O/Z)
HCS/PPERR§
HDS1/PSERR§
N9
I/O/Z
Host chip select (I) [default] or PCI parity error (I/O/Z)
R5
I/O/Z
Host data strobe 1 (I) [default] or PCI system error (I/O/Z)
HDS2/PCBE1§
HRDY/PIRDY§
P6
I/O/Z
Host data strobe 2 (I) [default] or PCI command/byte enable 1 (I/O/Z)
N4
I/O/Z
Host ready from DSP to host (O) [default] or PCI initiator ready (I/O/Z).
HD31/AD31§
HD30/AD30§
K7
HD29/AD29§
HD28/AD28§
K4
J4
J5
HD27/AD27§
HD26/AD26§
K5
HD25/AD25§
HD24/AD24§
L8
HD23/AD23§
HD22/AD22§
L5
L6
J6
M6
HD19/AD19§
HD18/AD18§
L4
As HPI data bus (PCI_EN pin = 0)
• Used for transfer of data, address, and control
• Host-Port bus width user-configurable at device reset via a 10-kΩ resistor pullup/pulldown
resistor on the HD5 pin:
M8
M4
HD17/AD17§
HD16/AD16§
M9
HD15/AD15§
HD14/AD14§
P8
M7
R6
HD13/AD13§
HD12/AD12§
R4
HD11/AD11§
HD10/AD10§
R7
HD9/AD9§
HD8/AD8§
T4
P9
HD7/AD7§
HD6/AD6§
R8
P7
T5
I/O/Z
HD5 pin = 0: HPI operates as an HPI16.
(HPI bus is 16 bits wide. HD[15:0] pins are used and the remaining HD[31:16] pins are
reserved pins in the high-impedance state.)
HD5 pin = 1: HPI operates as an HPI32.
(HPI bus is 32 bits wide. All HD[31:0] pins are used for host-port operations.)
As PCI data-address bus (PCI_EN pin = 1) [C6415 and C6416 devices only]
• Used for transfer of data and address
The C6414 device does not support the PCI peripheral; therefore, the HPI peripheral pins are
standalone peripheral functions, not MUXed.
T6
HD5/AD5§
HD4/AD4§
U4
HD3/AD3§
HD2/AD2§
T7
HD1/AD1§
HD0/AD0§
Host-port data (I/O/Z) [default] (C64x) or PCI data-address bus (I/O/Z) [C6415 and C6416]
M5
HD21/AD21§
HD20/AD20§
U5
U6
V4
V5
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
§ For the C6415 and C6416 devices, these pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
The C6414 device does not support the PCI or UTOPIA peripherals; therefore, these MUXed peripheral pins are standalone peripheral functions
for this device.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
43
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
HOST-PORT INTERFACE (HPI) [C64x] or PERIPHERAL COMPONENT INTERCONNECT (PCI) [C6415 or C6416 devices only]
(CONTINUED)
PCBE0
PCI command/byte enable 0 (I/O/Z). When PCI is disabled (PCI_EN = 0), this pin is tied-off.
For the C6414 device this pin is “Reserved (leave unconnected, do not connect to power or
ground).”
Y3
I/O/Z
XSP_CS
AA3
O
IPD
PCI serial interface chip select (O). When PCI is disabled (PCI_EN = 0), this pin is tied-off.
For the C6414 device this pin is “Reserved (leave unconnected, do not connect to power or
ground).”
CLKX2/
XSP_CLK§
W5
I/O/Z
IPD
McBSP2 transmit clock (I/O/Z) [default] or PCI serial interface clock (O).
DR2/XSP_DI§
Y4
I
IPU
McBSP2 receive data (I) [default] or PCI serial interface data in (I). In PCI mode, this pin is
connected to the output data pin of the serial PROM.
DX2/XSP_DO§
R9
O/Z
IPU
McBSP2 transmit data (O/Z) [default] or PCI serial interface data out (O). In PCI mode, this pin
is connected to the input data pin of the serial PROM.
GP15/PRST§
GP14/PCLK§
J8
General-purpose input/output (GPIO) 15 pin (I/O/Z) or PCI reset (I). No function at default.
G5
GPIO 14 pin (I/O/Z) or PCI clock (I). No function at default.
GP13/PINTA§
GP12/PGNT§
G4
GP11/PREQ§
GP10/PCBE3§
H6
GPIO 11 pin (I/O/Z) or PCI bus request (O/Z). No function at default.
L7
GPIO 10 pin (I/O/Z) or PCI command/byte enable 3 (I/O/Z). No function at default.
GP9/PIDSEL§
K6
ACE3
K20
O/Z
IPU
ACE2
L17
O/Z
IPU
ACE1
J21
O/Z
IPU
ACE0
K19
O/Z
IPU
ABE7
P19
O/Z
IPU
ABE6
U22
O/Z
IPU
ABE5
T22
O/Z
IPU
ABE4
R21
O/Z
IPU
ABE3
M17
O/Z
IPU
ABE2
M18
O/Z
IPU
ABE1
H22
O/Z
IPU
ABE0
L19
O/Z
IPU
J7
GPIO 13 pin (I/O/Z) or PCI interrupt A (O/Z). No function at default.
GPIO 12 pin (I/O/Z) or PCI bus grant (I). No function at default.
I/O/Z
GPIO 9 pin (I/O/Z) or PCI initialization device select (I). No function at default.
EMIFA (64-bit) − CONTROL SIGNALS COMMON TO ALL TYPES OF MEMORY||
EMIFA memory space enables
• Enabled by bits 28 through 31 of the word address
• Only one pin is asserted during any external data access
EMIFA byte-enable control
• Decoded from the low-order address bits. The number of address bits or byte enables
used depends on the width of external memory.
• Byte-write enables for most types of memory
• Can be directly connected to SDRAM read and write mask signal (SDQM)
APDT
L20
O/Z
IPU
EMIFA peripheral data transfer, allows direct transfer between external peripherals
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
§ For the C6415 and C6416 devices, these pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
The C6414 device does not support the PCI or UTOPIA peripherals; therefore, these MUXed peripheral pins are standalone peripheral functions
for this device.
|| These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.
To maintain signal integrity for the EMIF signals, serial termination resistors should be inserted into all EMIF output signal lines.
44
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
EMIFA (64-BIT) − BUS ARBITRATION||
AHOLDA
M19
O
IPU
EMIFA hold-request-acknowledge to the host
AHOLD
U21
I
IPU
EMIFA hold request from the host
ABUSREQ
P21
O
IPU
EMIFA bus request output
EMIFA (64-BIT) − ASYNCHRONOUS/SYNCHRONOUS MEMORY CONTROL||
AECLKIN
J19
I
IPD
EMIFA external input clock. The EMIFA input clock (AECLKIN, CPU/4 clock, or CPU/6 clock)
is selected at reset via the pullup/pulldown resistors on the BEA[17:16] pins.
AECLKIN is the default for the EMIFA input clock.
AECLKOUT2
K18
O/Z
IPD
EMIFA output clock 2. Programmable to be EMIFA input clock (AECLKIN, CPU/4 clock, or
CPU/6 clock) frequency divided-by-1, -2, or -4.
AECLKOUT1
H21
O/Z
IPD
EMIFA output clock 1 [at EMIFA input clock (AECLKIN, CPU/4 clock, or CPU/6 clock)
frequency].
AARE/
ASDCAS/
ASADS/ASRE
L16
O/Z
IPU
EMIFA asynchronous memory read-enable/SDRAM column-address strobe/programmable
synchronous interface-address strobe or read-enable
• For programmable synchronous interface, the RENEN field in the CE Space Secondary
Control Register (CExSEC) selects between ASADS and ASRE:
If RENEN = 0, then the ASADS/ASRE signal functions as the ASADS signal.
If RENEN = 1, then the ASADS/ASRE signal functions as the ASRE signal.
AAOE/
ASDRAS/
ASOE
J20
O/Z
IPU
EMIFA asynchronous memory output-enable/SDRAM row-address strobe/programmable
synchronous interface output-enable
AAWE/
ASDWE/
ASWE
G22
O/Z
IPU
EMIFA asynchronous memory write-enable/SDRAM write-enable/programmable synchronous interface write-enable
ASDCKE
K21
O/Z
IPU
EMIFA SDRAM clock-enable (used for self-refresh mode). [EMIFA module only.]
• If SDRAM is not in system, ASDCKE can be used as a general-purpose output.
ASOE3
N16
O/Z
IPU
EMIFA synchronous memory output-enable for ACE3 (for glueless FIFO interface)
AARDY
L18
I
IPU
Asynchronous memory ready input
EMIFA (64-BIT) − ADDRESS||
AEA22
R20
AEA21
P16
AEA20
T20
AEA19
R18
O/Z
IPD
EMIFA external address (doubleword address)
AEA18
V22
AEA17
R19
AEA16
T21
AEA15
P17
AEA14
N18
AEA13
P18
AEA12
P20
AEA11
N17
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
|| These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.
To maintain signal integrity for the EMIF signals, serial termination resistors should be inserted into all EMIF output signal lines.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
45
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
EMIFA (64-BIT) − ADDRESS|| (CONTINUED)
AEA10
N20
AEA9
N21
AEA8
N19
AEA7
M21
AEA6
M20
AEA5
L21
AEA4
M16
AEA3
J22
O/Z
IPD
EMIFA external address (doubleword address)
EMIFA (64-bit) − DATA||
AED63
AB21
AED62
W18
AED61
Y19
AED60
V17
AED59
AA20
AED58
AA19
AED57
Y18
AED56
T15
AED55
U16
AED54
AB20
AED53
AA18
AED52
V16
AED51
W17
AED50
Y17
AED49
U15
AED48
AB19
AED47
T19
AED46
U20
AED45
R17
AED44
Y22
AED43
V21
AED42
T18
AED41
U19
AED40
W21
AED39
V20
AED38
R16
I/O/Z
IPU
EMIFA external data
AED37
T17
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
|| These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.
To maintain signal integrity for the EMIF signals, serial termination resistors should be inserted into all EMIF output signal lines.
46
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
EMIFA (64-bit) − DATA|| (CONTINUED)
AED36
U18
AED35
Y21
AED34
V19
AED33
W20
AED32
AA22
AED31
D22
AED30
G19
AED29
F20
AED28
H18
AED27
E21
AED26
F21
AED25
G20
AED24
K16
AED23
J17
AED22
E22
AED21
G21
AED20
J18
AED19
H19
AED18
H20
AED17
K17
AED16
F22
AED15
F16
AED14
E17
AED13
H15
AED12
C20
AED11
D18
AED10
G16
AED9
F17
AED8
D19
AED7
E18
AED6
J15
AED5
H16
AED4
G17
AED3
D20
AED2
F18
AED1
E19
I/O/Z
IPU
EMIFA external data
AED0
C21
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
|| These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.
To maintain signal integrity for the EMIF signals, serial termination resistors should be inserted into all EMIF output signal lines.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
47
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
EMIFB (16-bit) − CONTROL SIGNALS COMMON TO ALL TYPES OF MEMORY||
BCE3
D11
O/Z
IPU
BCE2
C9
O/Z
IPU
BCE1
H12
O/Z
IPU
BCE0
G12
O/Z
IPU
BBE1
D12
O/Z
IPU
BBE0
E12
O/Z
IPU
BPDT
E11
O/Z
IPU
EMIFB peripheral data transfer, allows direct transfer between external peripherals
EMIFB (16-BIT) − BUS ARBITRATION||
BHOLDA
F12
O
IPU
EMIFB hold-request-acknowledge to the host
BHOLD
C19
I
IPU
EMIFB hold request from the host
BBUSREQ
D14
O
IPU
EMIFB bus request output
EMIFB memory space enables
• Enabled by bits 26 through 31 of the word address
• Only one pin is asserted during any external data access
EMIFB byte-enable control
• Decoded from the low-order address bits. The number of address bits or byte enables
used depends on the width of external memory.
• Byte-write enables for most types of memory
• Can be directly connected to SDRAM read and write mask signal (SDQM)
EMIFB (16-BIT) − ASYNCHRONOUS/SYNCHRONOUS MEMORY CONTROL||
BECLKIN
E10
I
IPD
EMIFB external input clock. The EMIFB input clock (BECLKIN, CPU/4 clock, or CPU/6 clock)
is selected at reset via the pullup/pulldown resistors on the BEA[15:14] pins.
BECLKIN is the default for the EMIFB input clock.
BECLKOUT2
C8
O/Z
IPD
EMIFB output clock 2. Programmable to be EMIFB input clock (BECLKIN, CPU/4 clock, or
CPU/6 clock) frequency divided by 1, 2, or 4.
BECLKOUT1
J12
O/Z
IPD
EMIFB output clock 1 [at EMIFB input clock (BECLKIN, CPU/4 clock, or CPU/6 clock)
frequency].
BARE/
BSDCAS/
BSADS/BSRE
C7
O/Z
IPU
EMIFB asynchronous memory read-enable/SDRAM column-address strobe/programmable
synchronous interface-address strobe or read-enable
• For programmable synchronous interface, the RENEN field in the CE Space Secondary
Control Register (CExSEC) selects between BSADS and BSRE:
If RENEN = 0, then the BSADS/BSRE signal functions as the BSADS signal.
If RENEN = 1, then the BSADS/BSRE signal functions as the BSRE signal.
BAOE/
BSDRAS/
BSOE
D10
O/Z
IPU
EMIFB asynchronous memory output-enable/SDRAM row-address strobe/programmable
synchronous interface output-enable
BAWE/BSDWE/
BSWE
F11
O/Z
IPU
EMIFB asynchronous memory write-enable/SDRAM write-enable/programmable synchronous interface write-enable
BSOE3
J13
O/Z
IPU
EMIFB synchronous memory output enable for BCE3 (for glueless FIFO interface)
BARDY
G11
I
IPU
EMIFB asynchronous memory ready input
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
|| These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.
To maintain signal integrity for the EMIF signals, serial termination resistors should be inserted into all EMIF output signal lines.
48
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
EMIFB (16-BIT) − ADDRESS||
BEA20
E15
IPU
BEA19
D17
IPU
BEA18
J14
BEA17
E16
BEA16
G15
BEA15
C18
BEA14
F15
BEA13
D16
BEA12
H14
BEA11
F14
BEA10
C17
BEA9
G13
BEA8
G14
BEA7
E14
BEA6
H13
BEA5
C16
BEA4
D15
BEA3
E13
BEA2
D13
BEA1
F13
EMIFB external address (half-word address) (O/Z)
• Also controls initialization of DSP modes at reset (I) via pullup/pulldown resistors
− Device Endian mode
BEA20:
0 – Big Endian
1 − Little Endian (default mode)
− Boot mode
BEA[19:18]: 00 – No boot
01 − HPI boot
10 − EMIFB 8-bit ROM boot with default timings (default mode)
11 − Reserved
− EMIF clock select
BEA[17:16]: Clock mode select for EMIFA (AECLKIN_SEL[1:0])
00 – AECLKIN (default mode)
01 − CPU/4 Clock Rate
10 − CPU/6 Clock Rate
11 − Reserved
BEA[15:14]: Clock mode select for EMIFB (BECLKIN_SEL[1:0])
00 – BECLKIN (default mode)
01 − CPU/4 Clock Rate
10 − CPU/6 Clock Rate
11 − Reserved
I/O/Z
IPD
− PCI EEPROM Auto-Initialization (EEAI) [C6415 and C6416 devices only]
BEA13:
PCI auto-initialization via external EEPROM
If the PCI peripheral is disabled (PCI_EN pin = 0), this pin must not be pulled up.
0 − PCI auto-initialization through EEPROM is disabled (default).
1 − PCI auto-initialization through EEPROM is enabled.
− UTOPIA Enable (UTOPIA_EN) [C6415 and C6416 devices only]
BEA11:
UTOPIA peripheral enable (functional)
0 − UTOPIA disabled (McBSP1 enabled) [default]
1 − UTOPIA enabled (McBSP1 disabled)
The C6414 device does not support the PCI and UTOPIA peripherals; for proper device
operation, do not oppose the internal pulldowns (IPDs) on the BEA13 and BEA11 pins.
Also for proper C6414 device operation, do not oppose the IPDs on the BEA7, BEA8,
and BEA9 pins.
For proper C6415 device operation, the BEA7 pin must be externally pulled up with a
1-k
1-kΩ resistor.
For proper C6416 device operation, the BEA8 and BEA9 pins must be externally pulled
up with a 1-kΩ resistor.
For more details, see the Device Configurations section of this data sheet.
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
|| These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.
To maintain signal integrity for the EMIF signals, serial termination resistors should be inserted into all EMIF output signal lines.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
49
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
EMIFB (16-bit) − DATA||
BED15
F8
BED14
J10
BED13
D7
BED12
C5
BED11
H10
BED10
G9
BED9
C6
BED8
E8
BED7
E9
BED6
F9
BED5
G10
BED4
J11
BED3
D9
BED2
D8
BED1
H11
BED0
F10
I/O/Z
IPU
EMIFB external data
MULTICHANNEL BUFFERED SERIAL PORT 2 (McBSP2)
MCBSP2_EN
AB4
I
IPD
McBSP2 enable pin. This pin works in conjunction with the PCI_EN pin to enable/disable other
peripherals (for more details, see the Device Configurations section of this data sheet).
CLKS2/GP8§
W7
I/O/Z
IPD
McBSP2 external clock source (CLKS2) [input only] [default] or this pin can also be
programmed as a GPIO 8 pin (I/O/Z).
CLKR2
W4
I/O/Z
IPD
McBSP2 receive clock. When McBSP2 is disabled (PCI_EN = 1 and MCBSP2_EN pin = 0),
this pin is tied-off.
CLKX2/
XSP_CLK§
W5
I/O/Z
IPD
McBSP2 transmit clock (I/O/Z) [default] or PCI serial interface clock (O).
DR2/XSP_DI§
Y4
I
IPU
McBSP2 receive data (I) [default] or PCI serial interface data in (I). In PCI mode, this pin is
connected to the output data pin of the serial PROM.
DX2/XSP_DO§
R9
O/Z
IPU
McBSP2 transmit data (O/Z) [default] or PCI serial interface data out (O). In PCI mode, this pin
is connected to the input data pin of the serial PROM.
FSR2
V6
I/O/Z
IPD
McBSP2 receive frame sync. When McBSP2 is disabled (PCI_EN = 1 and MCBSP2_EN pin
= 0), this pin is tied-off.
FSX2
U7
I/O/Z
IPD
McBSP2 transmit frame sync. When McBSP2 is disabled (PCI_EN = 1 and MCBSP2_EN pin
= 0), this pin is tied-off.
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
§ For the C6415 and C6416 devices, these pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
The C6414 device does not support the PCI or UTOPIA peripherals; therefore, these MUXed peripheral pins except CLKS2/GP8 are standalone
peripheral functions for this device.
|| These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). The prefix “A” in front of a signal name indicates it is an EMIFA signal
whereas a prefix “B” in front of a signal name indicates it is an EMIFB signal. Throughout the rest of this document, in generic EMIF areas of
discussion, the prefix “A” or “B” may be omitted from the signal name.
To maintain signal integrity for the EMIF signals, serial termination resistors should be inserted into all EMIF output signal lines.
50
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP1)
CLKS1/
URADDR3§
Y8
I
McBSP1 external clock source (as opposed to internal) (I) [default] or UTOPIA receive
address 3 pin (I)
CLKR1/
URADDR2§
AB7
I/O/Z
McBSP1 receive clock (I/O/Z) [default] or UTOPIA receive address 2 pin (I)
CLKX1/
URADDR4§
T12
I/O/Z
McBSP1 transmit clock (I/O/Z) [default] or UTOPIA receive address 4 pin (I)
DR1/
UXADDR1§
V11
I
DX1/
UXADDR4§
Y10
I/O/Z
McBSP1 transmit data (O/Z) [default] or UTOPIA transmit address 4 pin (I)
FSR1/
UXADDR2§
AA8
I/O/Z
McBSP1 receive frame sync (I/O/Z) [default] or UTOPIA transmit address 2 pin (I)
FSX1/
UXADDR3§
AA11
I/O/Z
McBSP1 transmit frame sync (I/O/Z) [default] or UTOPIA transmit address 3 pin (I)
F4
I
IPD
McBSP0 external clock source (as opposed to internal)
CLKR0
F5
I/O/Z
IPD
McBSP0 receive clock
CLKX0
K9
I/O/Z
IPD
McBSP0 transmit clock
DR0
G6
I
IPU
McBSP0 receive data
McBSP1 receive data (I) [default] or UTOPIA transmit address 1 pin (I)
MULTICHANNEL BUFFERED SERIAL PORT 0 (McBSP0)
CLKS0
DX0
E4
O/Z
IPU
McBSP0 transmit data
FSR0
D3
I/O/Z
IPD
McBSP0 receive frame sync
FSX0
H7
I/O/Z
IPD
McBSP0 transmit frame sync
TOUT2
F7
O/Z
IPD
Timer 2 or general-purpose output
TINP2
D5
I
IPD
Timer 2 or general-purpose input
TOUT1
G8
O/Z
IPD
Timer 1 or general-purpose output
TINP1
D6
I
IPD
Timer 1 or general-purpose input
TIMER 2
TIMER 1
TIMER 0
TOUT0
H9
O/Z
IPD
Timer 0 or general-purpose output
TINP0
E7
I
IPD
Timer 0 or general-purpose input
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
§ For the C6415 and C6416 devices, these pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
The C6414 device does not support the PCI or UTOPIA peripherals; therefore, these MUXed peripheral pins are standalone peripheral functions
for this device.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
51
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
UNIVERSAL TEST AND OPERATIONS PHY INTERFACE FOR ASYNCHRONOUS TRANSFER MODE (ATM) [UTOPIA SLAVE]
[C6415 and C6416 devices only]
UTOPIA SLAVE (ATM CONTROLLER) − TRANSMIT INTERFACE
UXCLKY
UXCLAVY
AB8
AA13
I
Source clock for UTOPIA transmit driven by Master ATM Controller.
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
Transmit cell available status output signal from UTOPIA Slave.
0
indicates a complete cell is NOT available for transmit
1
indicates a complete cell is available for transmit
O/Z
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
UXENBY
UXSOCY
U13
Y12
I
◊
UTOPIA transmit interface enable input signal. Asserted by the Master ATM Controller to indicate that the UTOPIA Slave should put out on the Transmit Data Bus the first byte of valid data
and the UXSOC signal in the next clock cycle.
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
Transmit Start-of-Cell signal. This signal is output by the UTOPIA Slave on the rising edge of
the UXCLK, indicating that the first valid byte of the cell is available on the 8-bit Transmit Data
Bus (UXDATA[7:0]).
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
O/Z
McBSP1 [default] or UTOPIA transmit address pins
DX1/
UXADDR4§
As UTOPIA transmit address pins UXADDR[4:0] (I), UTOPIA_EN (BEA11 pin) = 1:
• 5-bit Slave transmit address input pins driven by the Master ATM Controller to identify and
select one of the Slave devices (up to 31 possible) in the ATM System.
Y10
I/O/Z
◊
•
UXADDR0 pin is tied off when the UTOPIA peripheral is disabled [UTOPIA_EN
(BEA11 pin) = 0]
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP1) section of this table.
FSX1/
UXADDR3§
AA11
FSR1/
UXADDR2§
AA8
I/O/Z
◊
DR1/
UXADDR1§
V11
I
◊
I/O/Z
◊
McBSP1 [default] or UTOPIA transmit address pins
As UTOPIA transmit address pins UXADDR[4:0] (I), UTOPIA_EN (BEA11 pin) = 1:
• 5-bit Slave transmit address input pins driven by the Master ATM Controller to identify and
select one of the Slave devices (up to 31 possible) in the ATM System.
•
UXADDR0 pin is tied off when the UTOPIA peripheral is disabled [UTOPIA_EN
(BEA11 pin) = 0]
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP1) section of this table.
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
§ For the C6415 and C6416 devices, these pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
The C6414 device does not support the PCI or UTOPIA peripherals; therefore, these MUXed peripheral pins are standalone peripheral functions
for this device.
For the C6415 and C6416 devices, external pulldowns required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other devices,
then a 10-kΩ resistor must be used to externally pull down each of these pins. If these pins are “no connects”, then only UXCLK and URCLK
need to be pulled down and other pulldowns are not necessary.
◊ For the C6415 and C6416 devices, external pullups required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other devices,
then a 10-kΩ resistor must be used to externally pull up each of these pins. If these pins are “no connects”, then the pullups are not necessary.
Ψ The C6414 device does not support the UTOPIA peripheral; therefore, these standalone UTOPIA pins are Reserved (leave unconnected, do
not connect to power or ground) with the exception of UXCLK and URCLK which should be connected to a 10-kΩ pulldown resistor (see the
square [] footnote).
UXADDR0Y
52
Y9
I
◊
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
UTOPIA SLAVE (ATM CONTROLLER) − TRANSMIT INTERFACE (CONTINUED)
UXDATA7Y
UXDATA6Y
W10
UXDATA5Y
UXDATA4Y
W9
UXDATA3Y
UXDATA2Y
UXDATA1Y
UXDATA0Y
T11
8-bit Transmit Data Bus
Using the Transmit Data Bus, the UTOPIA Slave (on the rising edge of the UXCLK) transmits
the 8-bit ATM cells to the Master ATM Controller.
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), these pins are tiedoff.
AB6
V10
O/Z
U10
AA7
V9
UTOPIA SLAVE (ATM CONTROLLER) − RECEIVE INTERFACE
URCLKY
URCLAVY
U12
AA14
I
Source clock for UTOPIA receive driven by Master ATM Controller.
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
Receive cell available status output signal from UTOPIA Slave.
0
indicates NO space is available to receive a cell from Master ATM Controller
1
indicates space is available to receive a cell from Master ATM Controller
O/Z
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
URENBY
AB16
I
◊
UTOPIA receive interface enable input signal. Asserted by the Master ATM Controller to indicate to the UTOPIA Slave to sample the Receive Data Bus (URDATA[7:0]) and URSOC signal
in the next clock cycle or thereafter.
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
Receive Start-of-Cell signal. This signal is output by the Master ATM Controller to indicate to
the UTOPIA Slave that the first valid byte of the cell is available to sample on the 8-bit Receive
Data Bus (URDATA[7:0]).
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), this pin is tied-off.
URSOCY
W13
I
CLKX1/
URADDR4§
T12
I/O/Z
◊
CLKS1/
URADDR3§
Y8
I
◊
As UTOPIA receive address pins URADDR[4:0] (I), UTOPIA_EN (BEA11 pin) = 1:
• 5-bit Slave receive address input pins driven by the Master ATM Controller to identify and
select one of the Slave devices (up to 31 possible) in the ATM System.
CLKR1/
URADDR2§
AB7
I/O/Z
◊
•
URADDR1Y
U11
I
◊
McBSP1 [default] or UTOPIA receive address pins
URADDR1 and URADDR0 pins are tied off when the UTOPIA peripheral is disabled
[UTOPIA_EN (BEA11 pin) = 0]
For the McBSP1 pin functions (UTOPIA_EN (BEA11 pin) = 0 [default]), see the MULTICHANNEL BUFFERED SERIAL PORT 1 (McBSP1) section of this table.
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
§ These pins are multiplexed pins. For more details, see the Device Configurations section of this data sheet.
External pulldowns required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other devices, then a 10-kΩ resistor must be
used to externally pull down each of these pins. If these pins are “no connects”, then only UXCLK and URCLK need to be pulled down and other
pulldowns are not necessary.
◊ External pullups required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other devices, then a 10-kΩ resistor must be used
to externally pull up each of these pins. If these pins are “no connects”, then the pullups are not necessary.
Ψ The C6414 device does not support the UTOPIA peripheral; therefore, these standalone UTOPIA pins are Reserved (leave unconnected, do
not connect to power or ground) with the exception of UXCLK and URCLK which should be connected to a 10-kΩ pulldown resistor (see the
square [] footnote).
URADDR0Y
AA9
I
◊
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
53
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
IPD/
IPU‡
DESCRIPTION
UTOPIA SLAVE (ATM CONTROLLER) − RECEIVE INTERFACE (CONTINUED)
URDATA7Y
URDATA6Y
AA10
URDATA5Y
URDATA4Y
W12
URDATA3Y
URDATA2Y
Y11
AB9
URDATA1Y
URDATA0Y
AA12
V12
W11
I
8-bit Receive Data Bus.
Using the Receive Data Bus, the UTOPIA Slave (on the rising edge of the URCLK) can receive
the 8-bit ATM cell data from the Master ATM Controller.
When the UTOPIA peripheral is disabled (UTOPIA_EN [BEA11 pin] = 0), these pins are tiedoff.
Y13
RESERVED FOR TEST
C4
H5
RSV
H3
Reserved (leave unconnected, do not connect to power or ground)
N3
P3
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
‡ IPD = Internal pulldown, IPU = Internal pullup. (These IPD/IPU signal pins feature a 30-kΩ IPD or IPU resistor. To pull up a signal to the opposite
supply rail, a 1-kΩ resistor should be used.)
External pulldowns required: If UTOPIA is selected (BEA11 = 1) and these pins are connected to other devices, then a 10-kΩ resistor must be
used to externally pull down each of these pins. If these pins are “no connects”, then only UXCLK and URCLK need to be pulled down and other
pulldowns are not necessary.
Ψ The C6414 device does not support the UTOPIA peripheral; therefore, these standalone UTOPIA pins are Reserved (leave unconnected, do
not connect to power or ground) with the exception of UXCLK and URCLK which should be connected to a 10-kΩ pulldown resistor (see the
square [] footnote).
54
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
DESCRIPTION
SUPPLY VOLTAGE PINS
AA23
AB10
AB11
AB14
AB15
AB2
AB23
AC10
AC12
AC14
AC16
AC19
AC21
AC22
AC3
AC4
AC6
AC8
B11
B13
B15
DVDD
B17
S
3.3-V supply voltage
(see the Power-Supply Decoupling section of this data sheet)
B19
B21
B22
B3
B4
B6
B9
C10
C11
C14
C15
C23
D2
D23
F2
F23
F3
G3
H2
J23
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
55
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
DESCRIPTION
SUPPLY VOLTAGE PINS (CONTINUED)
J3
K2
K22
K3
L22
L23
M2
N23
P2
P22
DVDD
R22
S
3.3-V supply voltage
(see the Power-Supply Decoupling section of this data sheet)
S
1.4 V supply voltage
(see the Power-Supply Decoupling section of this data sheet)
R23
T2
T3
U23
U3
V2
V3
W23
W3
Y2
A10
A12
A14
A16
A18
A20
A22
A4
A6
A8
CVDD
AA1
AB12
AB13
AB24
AC18
AC20
AC5
AD11
AD13
AD15
AD17
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
56
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
DESCRIPTION
SUPPLY VOLTAGE PINS (CONTINUED)
AD19
AD21
AD23
AD3
AD5
AD7
AD9
B20
B24
B5
B7
C1
C12
C13
C2
D24
E1
E23
F24
CVDD
G1
S
1.4 V supply voltage
(see the Power-Supply Decoupling section of this data sheet)
G23
H24
J1
K10
K12
K14
K24
L1
L11
L13
L15
L3
M10
M12
M14
M22
M24
M3
N1
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
57
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
DESCRIPTION
SUPPLY VOLTAGE PINS (CONTINUED
N11
N13
N15
N22
P10
P12
P14
P24
R1
CVDD
R11
S
1.4 V supply voltage
(see the Power-Supply Decoupling section of this data sheet)
R13
R15
R3
T24
U1
V24
W1
Y23
Y24
GROUND PINS
A11
A13
A15
A17
A19
A21
A23
A3
A5
A7
A9
VSS
AA2
GND
Ground pins
AA21
AA24
AA4
AB1
AB22
AB3
AC1
AC11
AC13
AC15
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
58
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
DESCRIPTION
GROUND PINS
AC17
AC2
AC23
AC24
AC7
AC9
AD10
AD12
AD14
AD16
AD18
AD2
AD20
AD22
AD4
AD6
AD8
B10
B12
VSS
B14
GND
Ground pins
B16
B18
B2
B23
B8
C22
C24
C3
D1
D21
D4
E2
E20
E24
E5
F1
F19
F6
G18
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
59
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
DESCRIPTION
GROUND PINS (CONTINUED)
G2
G24
G7
H1
H17
H23
H8
J16
J2
J24
J9
K1
K11
K13
K15
K23
L10
L12
L14
VSS
L2
GND
Ground pins
L24
M1
M11
M13
M15
M23
N10
N12
N14
N2
N24
P1
P11
P13
P15
P23
R10
R12
R14
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
60
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
Terminal Functions (Continued)
SIGNAL
NAME
NO.
TYPE†
DESCRIPTION
GROUND PINS (CONTINUED)
R2
R24
T1
T16
T23
T9
U17
U2
U24
U8
VSS
V1
GND
Ground pins
V18
V23
V7
W19
W2
W24
W6
Y1
Y20
Y5
† I = Input, O = Output, Z = High impedance, S = Supply voltage, GND = Ground
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
61
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
development support
TI offers an extensive line of development tools for the TMS320C6000 DSP platform, including tools to
evaluate the performance of the processors, generate code, develop algorithm implementations, and fully
integrate and debug software and hardware modules.
The following products support development of C6000 DSP-based applications:
Software Development Tools:
Code Composer Studio Integrated Development Environment (IDE): including Editor
C/C++/Assembly Code Generation, and Debug plus additional development tools
Scalable, Real-Time Foundation Software (DSP/BIOS), which provides the basic run-time target software
needed to support any DSP application.
Hardware Development Tools:
Extended Development System (XDS) Emulator (supports C6000 DSP multiprocessor system debug)
EVM (Evaluation Module)
For a complete listing of development-support tools for the TMS320C6000 DSP platform, visit the Texas
Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL). For
information on pricing and availability, contact the nearest TI field sales office or authorized distributor.
Code Composer Studio, DSP/BIOS, and XDS are trademarks of Texas Instruments.
62
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
device and development-support tool nomenclature
To designate the stages in the product development cycle, TI assigns prefixes to the part numbers of all
TMS320 DSP devices and support tools. Each military TMS320 DSP family member has one of three
prefixes: SMX, TMP, or SMJ. Texas Instruments recommends two of three possible prefix designators for
support tools: TMDX and TMDS. These prefixes represent evolutionary stages of product development from
engineering prototypes (SMX / TMDX) through fully qualified production devices/tools (SMJ / TMDS).
Device development evolutionary flow:
SMX
Preproduction device that is not necessarily representative of the final device’s electrical
specifications
TMP
Final silicon die that conforms to the device’s electrical specifications but has not completed
quality and reliability verification
SMJ
Fully qualified production device
Support tool development evolutionary flow:
TMDX
Development-support product that has not yet completed Texas Instruments internal qualification
testing.
TMDS
Fully qualified development-support product
SMX and TMP devices and TMDX development-support tools are shipped with appropriate disclaimers
describing their limitations and intended uses. Experimental devices (SMX) may not be representative of a final
product and Texas Instruments reserves the right to change or discontinue these products without notice.
SMJ devices and TMDS development-support tools have been characterized fully, and the quality and reliability
of the device have been demonstrated fully. TI’s standard warranty applies.
Predictions show that preproduction or prototype devices (SMX or TMP) have a greater failure rate than the
standard production devices. Texas Instruments recommends that these devices not be used in any production
system because their expected end-use failure rate still is undefined. Only qualified production devices are to
be used.
TI device nomenclature also includes a suffix with the device family name. This suffix indicates the package type
(for example, GAD), the temperature range (for example, blank is the default commercial temperature range),
and the device speed range in megahertz (for example, -6E3 is 600-MHz CPU, 133-MHz EMIFA). Figure 4
provides a legend for reading the complete device name for any SMJ320C64x DSP generation member.
TMS320 is a trademark of Texas Instruments.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
63
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
device and development-support tool nomenclature (continued)
Table 30. SMJ320C6414/C6415/C6416 Device Part Numbers (P/Ns) and Ordering Information
DEVICE SPEED, EMIF SPEED,
SILICON REVISION
CVDD
(CORE VOLTAGE)
DVDD
(I/O VOLTAGE)
OPERATING CASE
TEMPERATURE
RANGE
SMJ320C6414DGADW60†
600 MHz/4800 MIPS, 133-MHz EMIFA,
Silicon Rev. 1.1
1.4 V
3.3 V
−55C to 115C
SM320C6414DGADW60†
600 MHz/4800 MIPS, 133-MHz EMIFA,
Silicon Rev. 1.1
1.4 V
3.3 V
−55C to 115C
SMJ320C6415DGADW60
600 MHz/4800 MIPS, 133-MHz EMIFA,
Silicon Rev. 1.1
1.4 V
3.3 V
−55C to 115C
SM320C6415DGADW60
600 MHz/4800 MIPS, 133-MHz EMIFA,
Silicon Rev. 1.1
1.4 V
3.3 V
−55C to 115C
SMJ320C6416DGADW60†
600 MHz/4800 MIPS, 133-MHz EMIFA,
Silicon Rev. 1.1
1.4 V
3.3 V
−55C to 115C
SM320C6416DGADW60†
600 MHz/4800 MIPS, 133-MHz EMIFA,
Silicon Rev. 1.1
1.4 V
3.3 V
−55C to 115C
DEVICE ORDERABLE
P/N
C6414
C6415
C6416
† Product Preview
64
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
device and development-support tool nomenclature (continued)
SMJ 32
PREFIX
TMX =
TMP =
TMS =
SMX=
SMJ =
SM =
C 6415C GAD
( )
6E3
DEVICE SPEED RANGE
300
5E0 (500-MHz CPU, 100-MHz EMIF)
6E3 (600-MHz CPU, 133-MHz EMIFA)
7E3 (720-MHz CPU, 133-MHz EMIFA)
60 (600-MHz CPU, 133-MHz EMIFA) military
Experimental device
Prototype device
Qualified device
Preproduction device, MIL
MIL-PRF-38535, QML
Commercial processing
DEVICE FAMILY
3 or 32 or 320 = TMS320 DSP family
TEMPERATURE RANGE (DEFAULT: 0°C TO 90°C)†
Blank = 0°C to 90°C, commercial temperature
A
= −40°C to 105°C, extended temperature‡
W
= −55°C to 115°C, mil temp
PACKAGE TYPE§
GLZ = 532-pin plastic BGA
GAD = 570-pin ceramic micro pin PGA
TECHNOLOGY
C = CMOS
DEVICE¶
C64x DSP:
6411
6414D
6415D
6416D
6414C
6415C
6416C
† See the Recommended Operating Conditions section of this data sheet for more details.
‡ The extended temperature “A version” devices may have different operating conditions than the commercial temperature devices.
See the Recommended Operating Conditions section of this data sheet for more details.
§ BGA = Ball Grid Array.
PGA = Pin Grid Array.
¶ For the actual device part numbers (P/Ns) and ordering information, see Table 30 of this data sheet.
Figure 4. SMJ320C64x DSP Device Nomenclature (Including the C6414, C6415, and C6416 Devices)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
65
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
documentation support
Extensive documentation supports all TMS320 DSP family generations of devices from product
announcement through applications development. The types of documentation available include: data sheets,
such as this document, with design specifications; complete user’s reference guides for all devices and tools;
technical briefs; development-support tools; on-line help; and hardware and software applications. The
following is a brief, descriptive list of support documentation specific to the C6000 DSP devices:
The TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189) describes the
C6000 DSP CPU (core) architecture, instruction set, pipeline, and associated interrupts.
The TMS320C6000 DSP Peripherals Overview Reference Guide (literature number SPRU190) provides an
overview and briefly describes the functionality of the peripherals available on the C6000 DSP platform of
devices. This document also includes a table listing the peripherals available on the C6000 devices along with
literature numbers and hyperlinks to the associated peripheral documents.
The TMS320C64x Technical Overview (literature number SPRU395) gives an introduction to the C64x digital
signal processor, and discusses the application areas that are enhanced by the C64x DSP VelociTI.2 VLIW
architecture.
The TMS320C6414, TMS320C6415, and TMS320C6416 Digital Signal Processors Silicon Errata (literature
number SPRZ011) describes the known exceptions to the functional specifications for the SMJ320C6414,
SMJ320C6415, and SMJ320C6416 devices.
The TMS320C6414/15/16 Power Consumption Summary application report (literature number SPRA811)
discusses the power consumption for user applications with the SMJ320C6414, SMJ320C6415, and
SMJ320C6416 DSP devices.
The Using IBIS Models for Timing Analysis application report (literature number SPRA839) describes how to
properly use IBIS models to attain accurate timing analysis for a given system.
The tools support documentation is electronically available within the Code Composer Studio Integrated
Development Environment (IDE). For a complete listing of C6000 DSP latest documentation, visit the Texas
Instruments web site on the Worldwide Web at http://www.ti.com uniform resource locator (URL).
See the Worldwide Web URL for the How To Begin Development Today With the TMS320C6414,
TMS320C6415, and TMS320C6416 DSPs application report (literature number SPRA718), which describes
in more details the compatibility and similarities/differences among the C6414, C6415, C6416, and C6211
devices.
66
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
clock PLL
Most of the internal C64x DSP clocks are generated from a single source through the CLKIN pin. This source
clock either drives the PLL, which multiplies the source clock frequency to generate the internal CPU clock, or
bypasses the PLL to become the internal CPU clock.
To use the PLL to generate the CPU clock, the external PLL filter circuit must be properly designed. Figure 5
shows the external PLL circuitry for either x1 (PLL bypass) or other PLL multiply modes.
To minimize the clock jitter, a single clean power supply should power both the C64x DSP device and the
external clock oscillator circuit. The minimum CLKIN rise and fall times should also be observed. For the input
clock timing requirements, see the input and output clocks electrical section.
Rise/fall times, duty cycles (high/low pulse durations), and the load capacitance of the external clock source
must meet the DSP requirements in this data sheet (see the electrical characteristics over recommended
ranges of supply voltage and operating case temperature table and the input and output clocks electrical
section). Table 31 lists some examples of compatible CLKIN external clock sources:
Table 31. Compatible CLKIN External Clock Sources
COMPATIBLE PARTS FOR
EXTERNAL CLOCK SOURCES (CLKIN)
PART NUMBER
JITO-2
Fox Electronix
STA series, ST4100 series
SaRonix Corporation
Oscillators
PLL
MANUFACTURER
SG-636
Epson America
342
Corning Frequency Control
ICS525-02
Integrated Circuit Systems
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
67
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
clock PLL (continued)
3.3 V
CPU Clock
EMI
filter
C1
C2
10 µF
0.1 µF
/2
Peripheral Bus
/8
Timer Internal Clock
/4
CLKOUT4,
McBSP Internal Clock
/6
CLKOUT6
PLLV
CLKMODE0
CLKMODE1
PLLMULT
PLL
x6, x12
CLKIN
PLLCLK
1
ECLKIN_SEL (DEVCFG.[17,16]
and DEVCFG.[15,14])
00 01 10
/4
0
/2
ECLKIN
Internal to C64x
(For the PLL Options, CLKMODE Pins Setup, and
PLL Clock Frequency Ranges, see Table 32.)
EMIF
00 01 10
ECLKOUT1
ECLKOUT2
EK2RATE
(GBLCTL.[19,18])
NOTES: A. Place all PLL external components (C1, C2, and the EMI Filter) as close to the C6000 DSP device as possible. For the best
performance, TI recommends that all the PLL external components be on a single side of the board without jumpers, switches, or
components other than the ones shown.
B. For reduced PLL jitter, maximize the spacing between switching signals and the PLL external components (C1, C2, and the EMI
Filter).
C. The 3.3-V supply for the EMI filter must be from the same 3.3-V power plane supplying the I/O voltage, DVDD.
D. EMI filter manufacturer TDK part number ACF451832-333, -223, -153, -103. Panasonic part number EXCCET103U.
Figure 5. External PLL Circuitry for Either PLL Multiply Modes or x1 (Bypass) Mode
68
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
clock PLL (continued)
Table 32. SMJ320C64x PLL Multiply Factor Options, Clock Frequency Ranges, and Typical Lock Time†‡
GAD PACKAGE − Micro Pin PGA
CLKMODE1 CLKMODE0
CLKMODE
(PLL MULTIPLY
FACTORS)
CLKIN
RANGE
(MHz)
CPU CLOCK
FREQUENCY
RANGE (MHz)
CLKOUT4
RANGE (MHz)
CLKOUT6
RANGE (MHz)
TYPICAL
LOCK TIME
(µs)§
N/A
0
0
Bypass (x1)
30−75
30−75
7.5−18.8
5−12.5
0
1
x6
30−75
180−450
45−112.5
30−75
1
0
x12
30−60
360−720
90−180
60−120
75
1
1
Reserved
−
−
−
−
−
† These clock frequency range values are applicable to a C64x−60 speed device..
‡ Use external pullup resistors on the CLKMODE pins (CLKMODE1 and CLKMODE0) to set the C64x device to one of the valid PLL multiply clock
modes (x6 or x12). With internal pulldown resistors on the CLKMODE pins (CLKMODE1, CLKMODE0), the default clock mode is x1 (bypass).
§ Under some operating conditions, the maximum PLL lock time may vary by as much as 150% from the specified typical value. For example, if
the typical lock time is specified as 100 µs, the maximum value may be as long as 250 µs.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
69
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
general-purpose input/output (GPIO)
To use the GP[15:0] software-configurable GPIO pins, the GPxEN bits in the GP Enable (GPEN) Register and
the GPxDIR bits in the GP Direction (GPDIR) Register must be properly configured.
GPxEN =
1
GP[x] pin is enabled
GPxDIR =
0
GP[x] pin is an input
GPxDIR =
1
GP[x] pin is an output
where “x” represents one of the 15 through 0 GPIO pins
Figure 6 shows the GPIO enable bits in the GPEN register for the C6414/C6415/C6416 device. To use any of
the GPx pins as general-purpose input/output functions, the corresponding GPxEN bit must be set to “1”
(enabled). Default values are device-specific, so refer to Figure 6 for the C6414/15/16 default configuration.
31
24 23
16
Reserved
R-0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
GP15
EN
GP14
EN
GP13
EN
GP12
EN
GP11
EN
GP10
EN
GP9
EN
GP8
EN
GP7
EN
GP6
EN
GP5
EN
GP4
EN
GP3
EN
GP2
EN
GP1
EN
GP0
EN
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-1
R/W-1
R/W-1
R/W-1
R/W-1
R/W-0
R/W-0
R/W-1
Legend: R/W = Readable/Writable; -n = value after reset, -x = undefined value after reset
Figure 6. GPIO Enable Register (GPEN) [Hex Address: 01B0 0000]
Figure 7 shows the GPIO direction bits in the GPDIR register. This register determines if a given GPIO pin is
an input or an output providing the corresponding GPxEN bit is enabled (set to “1”) in the GPEN register. By
default, all the GPIO pins are configured as input pins.
31
24 23
16
Reserved
R-0
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
GP15
DIR
GP14
DIR
GP13
DIR
GP12
DIR
GP11
DIR
GP10
DIR
GP9
DIR
GP8
DIR
GP7
DIR
GP6
DIR
GP5
DIR
GP4
DIR
GP3
DIR
GP2
DIR
GP1
DIR
GP0
DIR
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
Legend: R/W = Readable/Writable; -n = value after reset, -x = undefined value after reset
Figure 7. GPIO Direction Register (GPDIR) [Hex Address: 01B0 0004]
For more detailed information on general-purpose inputs/outputs (GPIOs), see the TMS320C6000 DSP
General-Purpose Input/Output (GPIO) Reference Guide (literature number SPRU584).
70
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
power-down mode logic
Figure 8 shows the power-down mode logic on the C6414/C6415/C6416.
CLKOUT4
CLKOUT6
Internal Clock Tree
Clock
Distribution
and Dividers
PD1
PD2
PowerDown
Logic
Clock
PLL
IFR
IER
Internal
Peripherals
PWRD CSR
CPU
PD3
SMJ320C6414/15/16
CLKIN
RESET
† External input clocks, with the exception of CLKIN, are not gated by the power-down mode logic.
Figure 8. Power-Down Mode Logic†
triggering, wake-up, and effects
The power-down modes and their wake-up methods are programmed by setting the PWRD field (bits 15−10)
of the control status register (CSR). The PWRD field of the CSR is shown in Figure 9 and described in Table 33.
When writing to the CSR, all bits of the PWRD field should be set at the same time. Logic 0 should be used when
writing to the reserved bit (bit 15) of the PWRD field. The CSR is discussed in detail in the TMS320C6000 CPU
and Instruction Set Reference Guide (literature number SPRU189).
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
71
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
31
16
15
14
13
12
11
10
Reserved
Enable or
Non-Enabled
Interrupt Wake
Enabled
Interrupt Wake
PD3
PD2
PD1
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
R/W-0
9
7
8
0
Legend: R/W−x = Read/write reset value
NOTE: The shadowed bits are not part of the power-down logic discussion and therefore are not covered here. For information on these other
bit fields in the CSR register, see the TMS320C6000 CPU and Instruction Set Reference Guide (literature number SPRU189).
Figure 9. PWRD Field of the CSR Register
Power-down mode PD1 takes effect eight to nine clock cycles after the instruction that sets the PWRD bits in the
CSR. If PD1 mode is terminated by a non-enabled interrupt, the program execution returns to the instruction where
PD1 took effect. If PD1 mode is terminated by an enabled interrupt, the interrupt service routine will be executed
first, then the program execution returns to the instruction where PD1 took effect.
PD2 and PD3 modes can only be aborted by device reset. Table 33 summarizes all the power-down modes.
Table 33. Characteristics of the Power-Down Modes
PRWD FIELD
(BITS 15−10)
POWER-DOWN
MODE
WAKE-UP METHOD
000000
No power-down
—
—
001001
PD1
Wake by an enabled interrupt
010001
PD1
Wake by an enabled or
non-enabled interrupt
011010
011100
PD2†
PD3†
EFFECT ON CHIP’S OPERATION
CPU halted (except for the interrupt logic)
Power-down mode blocks the internal clock inputs at the
boundary of the CPU, preventing most of the CPU’s logic from
switching. During PD1, EDMA transactions can proceed
between peripherals and internal memory.
Wake by a device reset
Output clock from PLL is halted, stopping the internal clock
structure from switching and resulting in the entire chip being
halted. All register and internal RAM contents are preserved. All
functional I/O “freeze” in the last state when the PLL clock is
turned off.
Wake by a device reset
Input clock to the PLL stops generating clocks. All register and
internal RAM contents are preserved. All functional I/O “freeze” in
the last state when the PLL clock is turned off. Following reset, the
PLL needs time to re-lock, just as it does following power-up.
Wake-up from PD3 takes longer than wake-up from PD2 because
the PLL needs to be re-locked, just as it does following power-up.
All others
Reserved
—
—
† When entering PD2 and PD3, all functional I/O remains in the previous state. However, for peripherals which are asynchronous in nature or
peripherals with an external clock source, output signals may transition in response to stimulus on the inputs. Under these conditions,
peripherals will not operate according to specifications.
72
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
C64x power-down mode with an emulator
If user power-down modes are programmed, and an emulator is attached, the modes will be masked to allow
the emulator access to the system. This condition prevails until the emulator is reset or the cable is removed
from the header. If power measurements are to be performed when in a power-down mode, the emulator cable
should be removed.
When the DSP is in power-down mode PD2 or PD3, emulation logic will force any emulation execution
command (such as Step or Run) to spin in IDLE. For this reason, PC writes (such as loading code) will fail. A DSP
reset will be required to get the DSP out of PD2/PD3.
power-supply sequencing
TI DSPs do not require specific power sequencing between the core supply and the I/O supply. However,
systems should be designed to ensure that neither supply is powered up for extended periods of time
(>1 second) if the other supply is below the proper operating voltage.
power-supply design considerations
A dual-power supply with simultaneous sequencing can be used to eliminate the delay between core and I/O
power up. A Schottky diode can also be used to tie the core rail to the I/O rail (see Figure 10).
I/O Supply
DVDD
Schottky
Diode
C6000
DSP
Core Supply
CVDD
VSS
GND
Figure 10. Schottky Diode Diagram
Core and I/O supply voltage regulators should be located close to the DSP (or DSP array) to minimize
inductance and resistance in the power delivery path. Additionally, when designing for high-performance
applications utilizing the C6000 platform of DSPs, the PC board should include separate power planes for
core, I/O, and ground, all bypassed with high-quality low-ESL/ESR capacitors.
power-supply decoupling
In order to properly decouple the supply planes from system noise, place as many capacitors (caps) as possible
close to the DSP. Assuming 0603 caps, the user should be able to fit a total of 60 caps, 30 for the core supply
and 30 for the I/O supply. These caps need to be close to the DSP, no more than 1.25 cm maximum distance
to be effective. Physically smaller caps are better, such as 0402, but need to be evaluated from a
yield/manufacturing point-of-view. Parasitic inductance limits the effectiveness of the decoupling capacitors,
therefore physically smaller capacitors should be used while maintaining the largest available capacitance
value. As with the selection of any component, verification of capacitor availability over the product’s production
lifetime should be considered.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
73
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
IEEE 1149.1 JTAG compatibility statement
The SMJ320C6414/15/16 DSP requires that both TRST and RESET be asserted upon power up to be properly
initialized. While RESET initializes the DSP core, TRST initializes the DSP’s emulation logic. Both resets are
required for proper operation.
While both TRST and RESET need to be asserted upon power up, only RESET needs to be released for the
DSP to boot properly. TRST may be asserted indefinitely for normal operation, keeping the JTAG port interface
and DSP’s emulation logic in the reset state.
TRST only needs to be released when it is necessary to use a JTAG controller to debug the DSP or exercise
the DSP’s boundary scan functionality.
For maximum reliability, the SMJ320C6414/15/16 DSP includes an internal pulldown (IPD) on the TRST pin to
ensure that TRST will always be asserted upon power up and the DSP’s internal emulation logic will always be
properly initialized.
JTAG controllers from Texas Instruments actively drive TRST high. However, some third-party JTAG controllers
may not drive TRST high but expect the use of a pullup resistor on TRST.
When using this type of JTAG controller, assert TRST to initialize the DSP after power up and externally drive
TRST high before attempting any emulation or boundary scan operations. Following the release of RESET, the
low-to-high transition of TRST must be “seen” to latch the state of EMU1 and EMU0. The EMU[1:0] pins
configure the device for either Boundary Scan mode or Emulation mode. For more detailed information, see
the terminal functions section of this data sheet.
EMIF device speed
The rated EMIF speed, referring to both EMIFA and EMIFB, of these devices only applies to the SDRAM
interface when in a system that meets the following requirements:
−
1 chip-enable (CE) space (maximum of 2 chips) of SDRAM connected to EMIF
−
up to 1 CE space of buffers connected to EMIF
−
EMIF trace lengths between 1 and 3 inches
−
166-MHz SDRAM for 133-MHz operation (applies only to EMIFA)
−
143-MHz SDRAM for 100-MHz operation
Other configurations may be possible, but timing analysis must be done to verify all AC timings are met.
Verification of AC timings is mandatory when using configurations other than those specified above. TI
recommends utilizing I/O buffer information specification (IBIS) to analyze all AC timings.
To properly use IBIS models to attain accurate timing analysis for a given system, see the Using IBIS Models
for Timing Analysis application report (literature number SPRA839).
To maintain signal integrity, serial termination resistors should be inserted into all EMIF output signal lines (see
the Terminal Functions table for the EMIF output signals).
74
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
bootmode
The C6414/15/16 device resets using the active-low signal RESET. While RESET is low, the device is held in
reset and is initialized to the prescribed reset state. Refer to reset timing for reset timing characteristics and
states of device pins during reset. The release of RESET starts the processor running with the prescribed device
configuration and boot mode.
The C6414/C6415/C6416 has three types of boot modes:
Host boot
If host boot is selected, upon release of RESET, the CPU is internally “stalled” while the remainder of the
device is released. During this period, an external host can initialize the CPU’s memory space as necessary
through the host interface, including internal configuration registers, such as those that control the EMIF or
other peripherals. For the C6414 device, the HPI peripheral is used for host boot. For the C6415/C6416
device, the HPI peripheral is used for host boot if PCI_EN = 0, and the PCI peripheral is used for host boot if
PCI_EN = 1. Once the host is finished with all necessary initialization, it must set the DSPINT bit in the HPIC
register to complete the boot process. This transition causes the boot configuration logic to bring the CPU
out of the “stalled” state. The CPU then begins execution from address 0. The DSPINT condition is not
latched by the CPU, because it occurs while the CPU is still internally “stalled”. Also, DSPINT brings the CPU
out of the “stalled” state only if the host boot process is selected. All memory may be written to and read by
the host. This allows for the host to verify what it sends to the DSP if required. After the CPU is out of the
“stalled” state, the CPU needs to clear the DSPINT, otherwise, no more DSPINTs can be received.
EMIF boot (using default ROM timings)
Upon the release of RESET, the 1K-Byte ROM code located in the beginning of CE1 is copied to address 0
by the EDMA using the default ROM timings, while the CPU is internally “stalled”. The data should be stored
in the endian format that the system is using. In this case, the EMIF automatically assembles consecutive
8-bit bytes to form the 32-bit instruction words to be copied. The transfer is automatically done by the EDMA
as a single-frame block transfer from the ROM to address 0. After completion of the block transfer, the CPU
is released from the “stalled” state and starts running from address 0.
No boot
With no boot, the CPU begins direct execution from the memory located at address 0. Note: operation is
undefined if invalid code is located at address 0.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
75
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
absolute maximum ratings over operating case temperature range (unless otherwise noted)†
Supply voltage ranges: CVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . − 0.3 V to 1.8 V
DVDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4 V
Input voltage ranges: (except PCI), VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4 V
(PCI), VIP [C6415 and C6416 only] . . . . . . . . . . . . . . . . . . . . . −0.5 V to DVDD + 0.5 V
Output voltage ranges: (except PCI), VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 4 V
(PCI), VOP [C6415 and C6416 only] . . . . . . . . . . . . . . . . . . . . −0.5 V to DVDD + 0.5 V
Operating case temperature ranges, TC:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55C to 115C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65C to 150C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to VSS.
recommended operating conditions
MIN
NOM
MAX
UNIT
CVDD
Supply voltage, Core‡
1.36
1.4
1.44
V
DVDD
Supply voltage, I/O
3.14
3.3
3.46
V
VSS
VIH
Supply ground
0
0
0
V
High-level input voltage (except PCI)
2
VIL
VIP
Low-level input voltage (except PCI)
VIHP
VILP
High-level input voltage (PCI) [C6415 and C6416 only]
VOS
Maximum voltage during overshoot/undershoot
TC
Operating case temperature
Input voltage (PCI) [C6415 and C6416 only]
Low-level input voltage (PCI) [C6415 and C6416 only]
W version
V
0.8
V
−0.5
DVDD + 0.5
V
0.5DVDD
−0.5
−1.0§
DVDD + 0.5
V
0.3DVDD
4.3§
V
–55
115
V
C
‡ Future variants of the C641x DSPs may operate at voltages ranging from 0.9 V to 1.4 V to provide a range of system power/performance options.
TI highly recommends that users design-in a supply that can handle multiple voltages within this range (i.e., 1.2 V, 1.25 V, 1.3 V, 1.35 V, 1.4 V
with ± 3% tolerances) by implementing simple board changes such as reference resistor values or input pin configuration modifications. Examples
of such supplies include the PT4660, PT5500, PT5520, PT6440, and PT6930 series from Power Trends, a subsidiary of Texas Instruments. Not
incorporating a flexible supply may limit the system’s ability to easily adapt to future versions of C641x devices.
§ The absolute maximum ratings should not be exceeded for more than 30% of the cycle period.
Life vs. Temperature at 600 MHz
12
10
10
9
8
8
7
Life (yrs) 6
6
5
4
4
3
2
2
1
0
100
110
120
130
140
150
Junction Temp (C)
Figure 11. Impact of Elevated Temperature on Device Life
76
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
electrical characteristics over recommended ranges of supply voltage and operating case
temperature (unless otherwise noted)
TEST CONDITIONS†
PARAMETER
VOH
High-level output voltage (except PCI)
DVDD = MIN,
IOH = MAX
VOHP
High-level output voltage (PCI)
[C6415/C6416 only]
IOHP = −0.5 mA,
DVDD = 3.3 V
VOL
Low-level output voltage (except PCI)
DVDD = MIN,
IOL = MAX
VOLP
Low-level output voltage (PCI)
[C6415/C6416 only]
IOLP = 1.5 mA,
DVDD = 3.3 V
MIN
TYP
IIP
IOH
Input current (except PCI)
Input leakage current (PCI)
[C6415/C6416 only]§
High-level output current
0.9DVDD¶
V
0.4
0.1DVDD¶
V
±10
uA
50
100
150
uA
VI = VSS to DVDD opposing internal
pulldown resistor‡
−150
−100
−50
uA
0 < VIP < DVDD = 3.3 V
±10
uA
EMIF, CLKOUT4, CLKOUT6, EMUx
−16
mA
−8
mA
−0.5¶
mA
16
mA
8
mA
PCI/HPI
1.5¶
mA
±10
uA
Timer, UTOPIA, TDO, GPIO (Excluding
GP[15:9, 2, 1]), McBSP
EMIF, CLKOUT4, CLKOUT6, EMUx
Low-level output current
V
VI = VSS to DVDD opposing internal
pullup resistor‡
PCI/HPI
IOL
UNIT
V
VI = VSS to DVDD no opposing internal
resistor
II
MAX
2.4
Timer, UTOPIA, TDO, GPIO (Excluding
GP[15:9, 2, 1]), McBSP
IOZ
ICDD
Off-state output current
Core supply current#
VO = DVDD or 0 V
CVDD = 1.4 V, CPU clock = 600 MHz
750
mA
IDDD
Ci
I/O supply current#
DVDD = 3.3 V, CPU clock = 600 MHz
125
mA
Input capacitance
12
pF
Co
Output capacitance
12
pF
† For test conditions shown as MIN, MAX, or NOM, use the appropriate value specified in the recommended operating conditions table.
‡ Applies only to pins with an internal pullup (IPU) or pulldown (IPD) resistor.
§ PCI input leakage currents include Hi-Z output leakage for all bidirectional buffers with 3-state outputs.
¶ These rated numbers are from the PCI specification version 2.3. The DC specification and AC specification are defined in Tables 4-3 and 4-4,
respectively.
# Measured with average activity (50% high/50% low power). The actual current draw is highly application-dependent. For more details on core
and I/O activity, refer to the TMS320C6414/15/16 Power Consumption Summary application report (literature number SPRA811).
recommended clock and control signal transition behavior
All clocks and control signals must transition between VIH and VIL (or between VIL and VIH) in a monotonic
manner.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
77
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
PARAMETER MEASUREMENT INFORMATION
Tester Pin Electronics
42 W
Data Sheet Timing Reference Point
Output
Under
Test
3.5 nH
Transmission Line
Z0 = 50 W
(see note)
4.0 pF
Device Pin
(see note)
1.85 pF
NOTE: The data sheet provides timing at the device pin. For output timing analysis, the tester pin electronics and its transmission line effects
must be taken into account. A transmission line with a delay of 2 ns or longer can be used to produce the desired transmission line effect.
The transmission line is intended as a load only. It is not necessary to add or subtract the transmission line delay (2 ns or longer) from
the data sheet timings.
Input requirements in this data sheet are tested with an input slew rate of < 4 Volts per nanosecond (4 V/ns) at the device pin.
Figure 12. Test Load Circuit for AC Timing Measurements
The tester load circuit is for characterization and measurement of AC timing signals. This load does not indicate
the maximum load the device is capable of driving.
signal transition levels
All input and output timing parameters are referenced to 1.5 V for both “0” and “1” logic levels.
Vref = 1.5 V
Figure 13. Input and Output Voltage Reference Levels for AC Timing Measurements
All rise and fall transition timing parameters are referenced to VIL MAX and VIH MIN for input clocks, VOL MAX
and VOH MIN for output clocks, VILP MAX and VIHP MIN for PCI input clocks, and VOLP MAX and VOHP MIN for
PCI output clocks.
Vref = VIH MIN (or VOH MIN or
VIHP MIN or VOHP MIN)
Vref = VIL MAX (or VOL MAX or
VILP MAX or VOLP MAX)
Figure 14. Rise and Fall Transition Time Voltage Reference Levels
signal transition rates
All timings are tested with an input edge rate of 4 Volts per nanosecond (4 V/ns).
78
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
PARAMETER MEASUREMENT INFORMATION (CONTINUED)
timing parameters and board routing analysis
The timing parameter values specified in this data sheet do not include delays by board routings. As a good
board design practice, such delays must always be taken into account. Timing values may be adjusted by
increasing/decreasing such delays. TI recommends utilizing the available I/O buffer information specification
(IBIS) models to analyze the timing characteristics correctly. If needed, external logic hardware such as buffers
may be used to compensate any timing differences.
For inputs, timing is most impacted by the round-trip propagation delay from the DSP to the external device and
from the external device to the DSP. This round-trip delay tends to negatively impact the input setup time margin,
but also tends to improve the input hold time margins (see Table 34 and Figure 15).
Figure 15 represents a general transfer between the DSP and an external device. The figure also represents
board route delays and how they are perceived by the DSP and the external device.
Table 34. Board-Level Timings Example (see Figure 15)
NO.
DESCRIPTION
1
Clock route delay
2
Minimum DSP hold time
3
Minimum DSP setup time
4
External device hold time requirement
5
External device setup time requirement
6
Control signal route delay
7
External device hold time
8
External device access time
9
DSP hold time requirement
10
DSP setup time requirement
11
Data route delay
ECLKOUTx
(Output from DSP)
1
ECLKOUTx
(Input to External Device)
Control Signals†
(Output from DSP)
2
3
4
5
Control Signals
(Input to External Device)
6
7
Data Signals‡
(Output from External Device)
8
10
9
11
Data Signals‡
(Input to DSP)
† Control signals include data for Writes.
‡ Data signals are generated during Reads from an external device.
Figure 15. Board-Level Input/Output Timings
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
79
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
INPUT AND OUTPUT CLOCKS
timing requirements for CLKIN†‡§ (see Figure 16)
PLL MODE x12
NO.
1
2
3
4
PLL MODE x6
x1 (BYPASS)
MIN
MAX
MIN
MAX
MIN
MAX
20
33.3
13.3
33.3
13.3*
33.3
tc(CLKIN)
tw(CLKINH)
Cycle time, CLKIN
Pulse duration, CLKIN high
0.4C*
0.4C*
0.45C*
tw(CLKINL)
tt(CLKIN)
Pulse duration, CLKIN low
0.4C*
0.4C*
0.45C*
Transition time, CLKIN
5*
5*
*This parameter is not production tested.
† The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
‡ For more details on the PLL multiplier factors (x6, x12), see the Clock PLL section of this data sheet.
§ C = CLKIN cycle time in ns. For example, when CLKIN frequency is 50 MHz, use C = 20 ns.
1
4
2
CLKIN
3
4
Figure 16. CLKIN Timing
80
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
UNIT
ns
ns
ns
1*
ns
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
INPUT AND OUTPUT CLOCKS (CONTINUED)
switching characteristics over recommended operating conditions for CLKOUT4†‡§
(see Figure 17)
CLKMODE = x1, x6, x12
NO.
1
2
3
4
PARAMETER
MIN
UNIT
MAX
tJ(CKO4)
tw(CKO4H)
Period jitter, CLKOUT4
0*
±175*
ps
Pulse duration, CLKOUT4 high
2P − 0.7*
2P + 0.7*
ns
tw(CKO4L)
tt(CKO4)
Pulse duration, CLKOUT4 low
2P − 0.7*
2P + 0.7*
ns
1*
ns
Transition time, CLKOUT4
*This parameter is not production tested.
† The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
‡ PH is the high period of CLKIN in ns and PL is the low period of CLKIN in ns.
§ P = 1/CPU clock frequency in nanoseconds (ns)
Ideal Clock Period
4
2
CLKOUT4
1
3
4
Figure 17. CLKOUT4 Timing
switching characteristics over recommended operating conditions for CLKOUT6†‡§
(see Figure 18)
CLKMODE = x1, x6, x12
NO.
1
2
3
4
PARAMETER
MIN
UNIT
MAX
0*
±175*
ps
Pulse duration, CLKOUT6 high
3P − 0.7*
3P + 0.7*
ns
Pulse duration, CLKOUT6 low
3P − 0.7*
3P + 0.7*
ns
1*
ns
tJ(CKO6)
tw(CKO6H)
Period jitter, CLKOUT6
tw(CKO6L)
tt(CKO6)
Transition time, CLKOUT6
*This parameter is not production tested.
† The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
‡ PH is the high period of CLKIN in ns and PL is the low period of CLKIN in ns.
§ P = 1/CPU clock frequency in nanoseconds (ns)
Ideal Clock Period
4
2
CLKOUT6
3
1
4
Figure 18. CLKOUT6 Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
81
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
INPUT AND OUTPUT CLOCKS (CONTINUED)
timing requirements for ECLKIN for EMIFA and EMIFB†‡§ (see Figure 19)
NO.
1
2
3
4
tc(EKI)
tw(EKIH)
Cycle time, ECLKIN
MIN
6¶*
Pulse duration, ECLKIN high
2.7*
tw(EKIL)
tt(EKI)
Pulse duration, ECLKIN low
2.7*
Transition time, ECLKIN
MAX
UNIT
16P*
ns
ns
ns
2*
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
§ These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are
prefixed by a “B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted.
¶ Minimum ECLKIN times are based on internal logic speed; the maximum useable speed of the EMIF may be lower due to AC timing requirements.
On the 7E3 and 6E3 devices, 133-MHz operation is achievable if the requirements of the EMIF Device Speed section are met. On the 5E0 devices,
100-MHz operation is achievable if the requirements of the EMIF Device Speed section are met.
1
4
2
ECLKIN
3
4
Figure 19. ECLKIN Timing for EMIFA and EMIFB
switching characteristics over recommended operating conditions for ECLKOUT1 for EMIFA and
EMIFB modules§#|| (see Figure 20)
NO.
1
2
3
4
5
6
PARAMETER
MIN
tJ(EKO1)
tw(EKO1H)
Period jitter, ECLKOUT1
0*
MAX
±175*
Pulse duration, ECLKOUT1 high
EH − 0.7*
EH + 0.7*
ns
tw(EKO1L)
tt(EKO1)
Pulse duration, ECLKOUT1 low
EL − 0.7*
EL + 0.7*
ns
1*
ns
td(EKIH-EKO1H)
td(EKIL-EKO1L)
Delay time, ECLKIN high to ECLKOUT1 high
1*
8*
ns
Delay time, ECLKIN low to ECLKOUT1 low
1*
8*
ns
Transition time, ECLKOUT1
UNIT
ps
*This parameter is not production tested.
§ These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are
prefixed by a “B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted.
# The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
|| E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
EH is the high period of E (EMIF input clock period) in ns and EL is the low period of E (EMIF input clock period) in ns for EMIFA or EMIFB.
This period jitter specification was measured with CPU/4 or CPU/6 as the source of the EMIF input clock.
82
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
INPUT AND OUTPUT CLOCKS (CONTINUED)
ECLKIN
6
Ideal Clock Period
5
3
4
4
2
ECLKOUT1
1
Figure 20. ECLKOUT1 Timing for EMIFA and EMIFB Modules
switching characteristics over recommended operating conditions for ECLKOUT2 for the EMIFA
and EMIFB modules†‡§ (see Figure 21)
NO.
1
2
3
4
5
6
PARAMETER
MIN
tJ(EKO2)
tw(EKO2H)
Period jitter, ECLKOUT2
0*
MAX
±175¶*
Pulse duration, ECLKOUT2 high
0.5NE − 0.7*
0.5NE + 0.7*
ns
tw(EKO2L)
tt(EKO2)
Pulse duration, ECLKOUT2 low
0.5NE − 0.7*
0.5NE + 0.7*
ns
Transition time, ECLKOUT2
td(EKIH-EKO2H) Delay time, ECLKIN high to ECLKOUT2 high
td(EKIH-EKO2L) Delay time, ECLKIN high to ECLKOUT2 low
UNIT
ps
1*
ns
1*
8*
ns
1*
8*
ns
*This parameter is not production tested.
† The reference points for the rise and fall transitions are measured at VOL MAX and VOH MIN.
‡ These C64x devices have two EMIFs (64-bit EMIFA and 16-bit EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are
prefixed by a “B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted.
§ E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
N = the EMIF input clock divider; N = 1, 2, or 4.
¶ This period jitter specification was measured with CPU/4 or CPU/6 as the source of the EMIF input clock.
5
6
ECLKIN
3
Ideal Clock Period
2
4
4
ECLKOUT2
1
Figure 21. ECLKOUT2 Timing for the EMIFA and EMIFB Modules
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
83
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
ASYNCHRONOUS MEMORY TIMING
timing requirements for asynchronous memory cycles for EMIFA module†‡§
(see Figure 22 and Figure 23)
NO.
3
4
6
MIN
MAX
UNIT
tsu(EDV-AREH)
th(AREH-EDV)
Setup time, EDx valid before ARE high
6.5
ns
Hold time, EDx valid after ARE high
1
ns
tsu(ARDY-EKO1H)
th(EKO1H-ARDY)
Setup time, ARDY valid before ECLKOUTx high
3
ns
7
Hold time, ARDY valid after ECLKOUTx high
1
ns
† To ensure data setup time, simply program the strobe width wide enough. ARDY is internally synchronized. The ARDY signal is only recognized
two cycles before the end of the programmed strobe time and while ARDY is low, the strobe time is extended cycle-by-cycle. When ARDY is
recognized low, the end of the strobe time is two cycles after ARDY is recognized high. To use ARDY as an asynchronous input, the pulse width
of the ARDY signal should be wide enough (e.g., pulse width = 2E) to ensure setup and hold time is met.
‡ RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold. These parameters are
programmed via the EMIF CE space control registers.
§ These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the asynchronous
memory access signals are shown as generic (AOE, ARE, and AWE) instead of AAOE, AARE, and AAWE (for EMIFA) and BAOE, BARE, and
BAWE (for EMIFB)].
switching characteristics over recommended operating conditions for asynchronous memory
cycles for EMIFA moduleद# (see Figure 22 and Figure 23)
NO.
1
2
5
8
9
PARAMETER
MIN
MAX
UNIT
tosu(SELV-AREL)
toh(AREH-SELIV)
Output setup time, select signals valid to ARE low
td(EKO1H-AREV)
tosu(SELV-AWEL)
Delay time, ECLKOUTx high to ARE valid
Output setup time, select signals valid to AWE low
WS * E − 1.7
ns
toh(AWEH-SELIV)
td(EKO1H-AWEV)
Output hold time, AWE high to select signals invalid
WH * E − 1.8
ns
Output hold time, ARE high to select signals invalid
RS * E − 2
ns
RH * E − 1.9
ns
1
7
ns
10
Delay time, ECLKOUTx high to AWE valid
1.3
7.1
ns
‡ RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold. These parameters are
programmed via the EMIF CE space control registers.
§ These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the asynchronous
memory access signals are shown as generic (AOE, ARE, and AWE) instead of AAOE, AARE, and AAWE (for EMIFA) and BAOE, BARE, and
BAWE (for EMIFB)].
¶ E = ECLKOUT1 period in ns for EMIFA or EMIFB
# Select signals for EMIFA include: ACEx, ABE[7:0], AEA[22:3], AAOE; and for EMIFA writes, include AED[63:0].
Select signals EMIFB include: BCEx, BBE[1:0], BEA[20:1], BAOE; and for EMIFB writes, include BED[15:0].
84
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
timing requirements for asynchronous memory cycles for EMIFB module†‡§
(see Figure 22 and Figure 23)
NO.
3
4
6
7
MIN
tsu(EDV-AREH)
th(AREH-EDV)
Setup time, EDx valid before ARE high
tsu(ARDY-EKO1H)
th(EKO1H-ARDY)
Setup time, ARDY valid before ECLKOUTx high
Hold time, EDx valid after ARE high
Hold time, ARDY valid after ECLKOUTx high
MAX
UNIT
6.2
ns
1
ns
3
ns
1.2
ns
† To ensure data setup time, simply program the strobe width wide enough. ARDY is internally synchronized. The ARDY signal is only recognized
two cycles before the end of the programmed strobe time and while ARDY is low, the strobe time is extended cycle-by-cycle. When ARDY is
recognized low, the end of the strobe time is two cycles after ARDY is recognized high. To use ARDY as an asynchronous input, the pulse width
of the ARDY signal should be wide enough (e.g., pulse width = 2E) to ensure setup and hold time is met.
‡ RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold. These parameters are
programmed via the EMIF CE space control registers.
§ These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the asynchronous
memory access signals are shown as generic (AOE, ARE, and AWE) instead of AAOE, AARE, and AAWE (for EMIFA) and BAOE, BARE, and
BAWE (for EMIFB)].
switching characteristics over recommended operating conditions for asynchronous memory
cycles for EMIFB moduleद# (see Figure 22 and Figure 23)
NO.
1
2
5
8
9
10
PARAMETER
MIN
tosu(SELV-AREL)
toh(AREH-SELIV)
Output setup time, select signals valid to ARE low
td(EKO1H-AREV)
tosu(SELV-AWEL)
Delay time, ECLKOUTx high to ARE valid
Output setup time, select signals valid to AWE low
WS * E − 1.9
toh(AWEH-SELIV)
td(EKO1H-AWEV)
Output hold time, AWE high to select signals invalid
WH * E − 1.7
Output hold time, ARE high to select signals invalid
Delay time, ECLKOUTx high to AWE valid
MAX
RS * E − 2
ns
RH * E − 1.7
0.8
ns
6.6
ns
ns
ns
ns
‡ RS = Read setup, RST = Read strobe, RH = Read hold, WS = Write setup, WST = Write strobe, WH = Write hold. These parameters are
programmed via the EMIF CE space control registers.
§ These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the asynchronous
memory access signals are shown as generic (AOE, ARE, and AWE) instead of AAOE, AARE, and AAWE (for EMIFA) and BAOE, BARE, and
BAWE (for EMIFB)].
¶ E = ECLKOUT1 period in ns for EMIFA or EMIFB
# Select signals for EMIFA include: ACEx, ABE[7:0], AEA[22:3], AAOE; and for EMIFA writes, include AED[63:0].
Select signals EMIFB include: BCEx, BBE[1:0], BEA[20:1], BAOE; and for EMIFB writes, include BED[15:0].
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
0.9
UNIT
6.7
85
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
Setup = 2
Strobe = 3
Not Ready
Hold = 2
ECLKOUTx
1
2
1
2
CEx
BE
ABE[7:0] or BBE[1:0]
2
1
AEA[22:3] or BEA[20:1]
Address
3
4
AED[63:0] or BED[15:0]
1
2
Read Data
AOE/SDRAS/SOE‡
5
5
ARE/SDCAS/SADS/SRE‡
AWE/SDWE/SWE‡
7
7
6
6
ARDY
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the asynchronous
memory access signals are shown as generic (AOE, ARE, and AWE) instead of AAOE, AARE, and AAWE (for EMIFA) and BAOE, BARE, and
BAWE (for EMIFB)].
‡ AOE/SDRAS/SOE, ARE/SDCAS/SADS/SRE, and AWE/SDWE/SWE operate as AOE (identified under select signals), ARE, and AWE,
respectively, during asynchronous memory accesses.
Figure 22. Asynchronous Memory Read Timing for EMIFA and EMIFB†
86
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
ASYNCHRONOUS MEMORY TIMING (CONTINUED)
Setup = 2
Strobe = 3
Hold = 2
Not Ready
ECLKOUTx
9
8
CEx
9
8
BE
ABE[7:0] or BBE[1:0]
9
8
AEA[22:3] or BEA[20:1]
Address
9
8
AED[63:0] or BED[15:0]
Write Data
AOE/SDRAS/SOE‡
ARE/SDCAS/SADS/SRE‡
10
10
AWE/SDWE/SWE‡
7
6
7
6
ARDY
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the asynchronous
memory access signals are shown as generic (AOE, ARE, and AWE) instead of AAOE, AARE, and AAWE (for EMIFA) and BAOE, BARE, and
BAWE (for EMIFB)].
‡ AOE/SDRAS/SOE, ARE/SDCAS/SADS/SRE, and AWE/SDWE/SWE operate as AOE (identified under select signals), ARE, and AWE,
respectively, during asynchronous memory accesses.
Figure 23. Asynchronous Memory Write Timing for EMIFA and EMIFB†
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
87
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
PROGRAMMABLE SYNCHRONOUS INTERFACE TIMING
timing requirements for programmable synchronous interface cycles for EMIFA module†
(see Figure 24)
NO.
6
7
MIN
tsu(EDV-EKOxH)
th(EKOxH-EDV)
Setup time, read EDx valid before ECLKOUTx high
Hold time, read EDx valid after ECLKOUTx high
MAX
2
UNIT
ns
ns
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the programmable
synchronous interface access signals are shown as generic (SADS/SRE, SOE, and SWE) instead of ASADS/ASRE, ASOE, and ASWE (for
EMIFA) and BSADS/BSRE, BSOE, and BSWE (for EMIFB)].
switching characteristics over recommended operating conditions for
synchronous interface cycles for EMIFA module†‡ (see Figure 24−Figure 26)
NO.
1
2
3
4
5
8
9
10
11
PARAMETER
1.5
programmable
MIN
MAX
1.3
4.9
UNIT
ns
5.1
ns
td(EKOxH-CEV)
td(EKOxH-BEV)
Delay time, ECLKOUTx high to CEx valid
td(EKOxH-BEIV)
td(EKOxH-EAV)
Delay time, ECLKOUTx high to BEx invalid
td(EKOxH-EAIV)
td(EKOxH-ADSV)
Delay time, ECLKOUTx high to EAx invalid
1.3
Delay time, ECLKOUTx high to SADS/SRE valid
1.3
4.9
ns
td(EKOxH-OEV)
td(EKOxH-EDV)
Delay time, ECLKOUTx high to, SOE valid
1.3
4.9
ns
4.9
ns
td(EKOxH-EDIV)
td(EKOxH-WEV)
Delay time, ECLKOUTx high to EDx invalid
Delay time, ECLKOUTx high to BEx valid
1.3
Delay time, ECLKOUTx high to EAx valid
ns
4.9
Delay time, ECLKOUTx high to EDx valid
1.3
ns
ns
ns
12
Delay time, ECLKOUTx high to SWE valid
1.3
4.9
ns
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the programmable
synchronous interface access signals are shown as generic (SADS/SRE, SOE, and SWE) instead of ASADS/ASRE, ASOE, and ASWE (for
EMIFA) and BSADS/BSRE, BSOE, and BSWE (for EMIFB)].
‡ The following parameters are programmable via the EMIF CE Space Secondary Control register (CExSEC):
− Read latency (SYNCRL): 0-, 1-, 2-, or 3-cycle read latency
− Write latency (SYNCWL): 0-, 1-, 2-, or 3-cycle write latency
− CEx assertion length (CEEXT): For standard SBSRAM or ZBT SRAM interface, CEx goes inactive after the final command has been issued
(CEEXT = 0). For synchronous FIFO interface with glue, CEx is active when SOE is active (CEEXT = 1).
− Function of SADS/SRE (RENEN): For standard SBSRAM or ZBT SRAM interface, SADS/SRE acts as SADS with deselect cycles
(RENEN = 0). For FIFO interface, SADS/SRE acts as SRE with NO deselect cycles (RENEN = 1).
− Synchronization clock (SNCCLK): Synchronized to ECLKOUT1 or ECLKOUT2
88
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
PROGRAMMABLE SYNCHRONOUS INTERFACE TIMING (CONTINUED)
timing requirements for programmable synchronous interface cycles for EMIFB module†
(see Figure 24)
NO.
6
7
MIN
tsu(EDV-EKOxH)
th(EKOxH-EDV)
Setup time, read EDx valid before ECLKOUTx high
3.1
Hold time, read EDx valid after ECLKOUTx high
1.5
MAX
UNIT
ns
ns
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the programmable
synchronous interface access signals are shown as generic (SADS/SRE, SOE, and SWE) instead of ASADS/ASRE, ASOE, and ASWE (for
EMIFA) and BSADS/BSRE, BSOE, and BSWE (for EMIFB)].
switching characteristics over recommended operating conditions for
synchronous interface cycles for EMIFB module†‡ (see Figure 24−Figure 26)
NO.
1
2
3
4
5
8
9
10
11
PARAMETER
programmable
MIN
MAX
1.3
6.4
UNIT
ns
6.4
ns
td(EKOxH-CEV)
td(EKOxH-BEV)
Delay time, ECLKOUTx high to CEx valid
td(EKOxH-BEIV)
td(EKOxH-EAV)
Delay time, ECLKOUTx high to BEx invalid
td(EKOxH-EAIV)
td(EKOxH-ADSV)
Delay time, ECLKOUTx high to EAx invalid
1.3
Delay time, ECLKOUTx high to SADS/SRE valid
1.3
6.4
ns
td(EKOxH-OEV)
td(EKOxH-EDV)
Delay time, ECLKOUTx high to, SOE valid
1.3
6.4
ns
6.4
ns
td(EKOxH-EDIV)
td(EKOxH-WEV)
Delay time, ECLKOUTx high to EDx invalid
Delay time, ECLKOUTx high to BEx valid
1.3
Delay time, ECLKOUTx high to EAx valid
ns
6.4
Delay time, ECLKOUTx high to EDx valid
1.3
ns
ns
ns
12
Delay time, ECLKOUTx high to SWE valid
1.3
6.4
ns
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the programmable
synchronous interface access signals are shown as generic (SADS/SRE, SOE, and SWE) instead of ASADS/ASRE, ASOE, and ASWE (for
EMIFA) and BSADS/BSRE, BSOE, and BSWE (for EMIFB)].
‡ The following parameters are programmable via the EMIF CE Space Secondary Control register (CExSEC):
− Read latency (SYNCRL): 0-, 1-, 2-, or 3-cycle read latency
− Write latency (SYNCWL): 0-, 1-, 2-, or 3-cycle write latency
− CEx assertion length (CEEXT): For standard SBSRAM or ZBT SRAM interface, CEx goes inactive after the final command has been issued
(CEEXT = 0). For synchronous FIFO interface with glue, CEx is active when SOE is active (CEEXT = 1).
− Function of SADS/SRE (RENEN): For standard SBSRAM or ZBT SRAM interface, SADS/SRE acts as SADS with deselect cycles
(RENEN = 0). For FIFO interface, SADS/SRE acts as SRE with NO deselect cycles (RENEN = 1).
− Synchronization clock (SNCCLK): Synchronized to ECLKOUT1 or ECLKOUT2
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
89
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
PROGRAMMABLE SYNCHRONOUS INTERFACE TIMING (CONTINUED)
READ latency = 2
ECLKOUTx
1
1
CEx
ABE[7:0] or BBE[1:0]
2
BE1
3
BE2
BE3
BE4
4
AEA[22:3] or BEA[20:1]
EA1
5
EA3
EA2
6
AED[63:0] or BED[15:0]
EA4
7
Q1
Q2
Q3
Q4
8
8
ARE/SDCAS/SADS/SRE§
9
9
AOE/SDRAS/SOE§
AWE/SDWE/SWE§
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the programmable
synchronous interface access signals are shown as generic (SADS/SRE, SOE, and SWE) instead of ASADS/ASRE, ASOE, and ASWE (for
EMIFA) and BSADS/BSRE, BSOE, and BSWE (for EMIFB)].
‡ The read latency and the length of CEx assertion are programmable via the SYNCRL and CEEXT fields, respectively, in the EMIFx CE Space
Secondary Control register (CExSEC). In this figure, SYNCRL = 2 and CEEXT = 0.
§ The following parameters are programmable via the EMIF CE Space Secondary Control register (CExSEC):
− Read latency (SYNCRL): 0-, 1-, 2-, or 3-cycle read latency
− Write latency (SYNCWL): 0-, 1-, 2-, or 3-cycle write latency
− CEx assertion length (CEEXT): For standard SBSRAM or ZBT SRAM interface, CEx goes inactive after the final command has been issued
(CEEXT = 0). For synchronous FIFO interface with glue, CEx is active when SOE is active (CEEXT = 1).
− Function of SADS/SRE (RENEN): For standard SBSRAM or ZBT SRAM interface, SADS/SRE acts as SADS with deselect cycles
(RENEN = 0). For FIFO interface, SADS/SRE acts as SRE with NO deselect cycles (RENEN = 1).
− Synchronization clock (SNCCLK): Synchronized to ECLKOUT1 or ECLKOUT2
¶ ARE/SDCAS/SADS/SRE, AOE/SDRAS/SOE, and AWE/SDWE/SWE operate as SADS/SRE, SOE, and SWE, respectively, during
programmable synchronous interface accesses.
Figure 24. Programmable Synchronous Interface Read Timing for EMIFA and EMIFB
(With Read Latency = 2)†‡§
90
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
PROGRAMMABLE SYNCHRONOUS INTERFACE TIMING (CONTINUED)
ECLKOUTx
1
1
CEx
ABE[7:0] or BBE[1:0]
2
BE1
AEA[22:3] or BEA[20:1]
4
EA1
EA2
EA3
EA4
10
Q1
Q2
Q3
Q4
10
AED[63:0] or BED[15:0]
ARE/SDCAS/SADS/SRE¶
3
BE2
BE3
BE4
5
11
8
8
AOE/SDRAS/SOE¶
12
12
AWE/SDWE/SWE¶
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the programmable
synchronous interface access signals are shown as generic (SADS/SRE, SOE, and SWE) instead of ASADS/ASRE, ASOE, and ASWE (for
EMIFA) and BSADS/BSRE, BSOE, and BSWE (for EMIFB)].
‡ The write latency and the length of CEx assertion are programmable via the SYNCWL and CEEXT fields, respectively, in the EMIFx CE Space
Secondary Control register (CExSEC). In this figure, SYNCWL = 0 and CEEXT = 0.
§ The following parameters are programmable via the EMIF CE Space Secondary Control register (CExSEC):
− Read latency (SYNCRL): 0-, 1-, 2-, or 3-cycle read latency
− Write latency (SYNCWL): 0-, 1-, 2-, or 3-cycle write latency
− CEx assertion length (CEEXT): For standard SBSRAM or ZBT SRAM interface, CEx goes inactive after the final command has been issued
(CEEXT = 0). For synchronous FIFO interface with glue, CEx is active when SOE is active (CEEXT = 1).
− Function of SADS/SRE (RENEN): For standard SBSRAM or ZBT SRAM interface, SADS/SRE acts as SADS with deselect cycles
(RENEN = 0). For FIFO interface, SADS/SRE acts as SRE with NO deselect cycles (RENEN = 1).
− Synchronization clock (SNCCLK): Synchronized to ECLKOUT1 or ECLKOUT2
¶ ARE/SDCAS/SADS/SRE, AOE/SDRAS/SOE, and AWE/SDWE/SWE operate as SADS/SRE, SOE, and SWE, respectively, during
programmable synchronous interface accesses.
Figure 25. Programmable Synchronous Interface Write Timing for EMIFA and EMIFB
(With Write Latency = 0)†‡§
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
91
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
PROGRAMMABLE SYNCHRONOUS INTERFACE TIMING (CONTINUED)
Write
Latency =
1‡
ECLKOUTx
1
1
CEx
ABE[7:0] or BBE[1:0]
2
BE1
AEA[22:3] or BEA[20:1]
4
EA1
10
AED[63:0] or BED[15:0]
3
BE2
BE3
BE4
5
EA2
10
EA3
EA4
Q1
Q2
Q3
11
Q4
8
8
ARE/SDCAS/SADS/SRE¶
AOE/SDRAS/SOE¶
12
12
AWE/SDWE/SWE¶
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the programmable
synchronous interface access signals are shown as generic (SADS/SRE, SOE, and SWE) instead of ASADS/ASRE, ASOE, and ASWE (for
EMIFA) and BSADS/BSRE, BSOE, and BSWE (for EMIFB)].
‡ The write latency and the length of CEx assertion are programmable via the SYNCWL and CEEXT fields, respectively, in the EMIFx CE Space
Secondary Control register (CExSEC). In this figure, SYNCWL = 1 and CEEXT = 0.
§ The following parameters are programmable via the EMIF CE Space Secondary Control register (CExSEC):
− Read latency (SYNCRL): 0-, 1-, 2-, or 3-cycle read latency
− Write latency (SYNCWL): 0-, 1-, 2-, or 3-cycle write latency
− CEx assertion length (CEEXT): For standard SBSRAM or ZBT SRAM interface, CEx goes inactive after the final command has been issued
(CEEXT = 0). For synchronous FIFO interface with glue, CEx is active when SOE is active (CEEXT = 1).
− Function of SADS/SRE (RENEN): For standard SBSRAM or ZBT SRAM interface, SADS/SRE acts as SADS with deselect cycles
(RENEN = 0). For FIFO interface, SADS/SRE acts as SRE with NO deselect cycles (RENEN = 1).
− Synchronization clock (SNCCLK): Synchronized to ECLKOUT1 or ECLKOUT2
¶ ARE/SDCAS/SADS/SRE, AOE/SDRAS/SOE, and AWE/SDWE/SWE operate as SADS/SRE, SOE, and SWE, respectively, during
programmable synchronous interface accesses.
Figure 26. Programmable Synchronous Interface Write Timing for EMIFA and EMIFB
(With Write Latency = 1)†‡§
92
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING
timing requirements for synchronous DRAM cycles for EMIFA module† (see Figure 27)
NO.
6
MIN
tsu(EDV-EKO1H)
th(EKO1H-EDV)
Setup time, read EDx valid before ECLKOUTx high
MAX
0.6
UNIT
ns
7
Hold time, read EDx valid after ECLKOUTx high
1.8
ns
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
switching characteristics over recommended operating conditions for synchronous DRAM cycles
for EMIFA module† (see Figure 27−Figure 34)
NO.
1
PARAMETER
MIN
MAX
1.3
4.9
UNIT
ns
4.9
ns
td(EKO1H-CEV)
td(EKO1H-BEV)
Delay time, ECLKOUTx high to CEx valid
td(EKO1H-BEIV)
td(EKO1H-EAV)
Delay time, ECLKOUTx high to BEx invalid
td(EKO1H-EAIV)
td(EKO1H-CASV)
Delay time, ECLKOUTx high to EAx invalid
1.3
Delay time, ECLKOUTx high to SDCAS valid
1.3
td(EKO1H-EDV)
td(EKO1H-EDIV)
Delay time, ECLKOUTx high to EDx valid
Delay time, ECLKOUTx high to EDx invalid
1.3
Delay time, ECLKOUTx high to SDWE valid
1.3
4.9
ns
12
td(EKO1H-WEV)
td(EKO1H-RAS)
Delay time, ECLKOUTx high to SDRAS valid
1.3
4.9
ns
13
td(EKO1H-ACKEV)
Delay time, ECLKOUTx high to ASDCKE valid (EMIFA only)
1.3
4.9
ns
2
3
4
5
8
9
10
11
Delay time, ECLKOUTx high to BEx valid
1.3
Delay time, ECLKOUTx high to EAx valid
ns
4.9
ns
ns
4.9
ns
4.9
ns
ns
14
td(EKO1H-PDTV)
Delay time, ECLKOUTx high to PDT valid
1.3
4.9
ns
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
93
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
timing requirements for synchronous DRAM cycles for EMIFB module† (see Figure 27)
NO.
6
MIN
tsu(EDV-EKO1H)
th(EKO1H-EDV)
Setup time, read EDx valid before ECLKOUTx high
MAX
2.1
UNIT
ns
7
Hold time, read EDx valid after ECLKOUTx high
2.5
ns
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
switching characteristics over recommended operating conditions for synchronous DRAM cycles
for EMIFB module† (see Figure 27−Figure 34)
NO.
1
PARAMETER
MIN
MAX
1.3
6.4
UNIT
ns
6.4
ns
td(EKO1H-CEV)
td(EKO1H-BEV)
Delay time, ECLKOUTx high to CEx valid
td(EKO1H-BEIV)
td(EKO1H-EAV)
Delay time, ECLKOUTx high to BEx invalid
td(EKO1H-EAIV)
td(EKO1H-CASV)
Delay time, ECLKOUTx high to EAx invalid
1.3
Delay time, ECLKOUTx high to SDCAS valid
1.3
td(EKO1H-EDV)
td(EKO1H-EDIV)
Delay time, ECLKOUTx high to EDx valid
Delay time, ECLKOUTx high to EDx invalid
1.3
Delay time, ECLKOUTx high to SDWE valid
1.3
6.4
ns
12
td(EKO1H-WEV)
td(EKO1H-RAS)
Delay time, ECLKOUTx high to SDRAS valid
1.3
6.4
ns
13
td(EKO1H-ACKEV)
Delay time, ECLKOUTx high to ASDCKE valid (EMIFA only)
1.3*
6.4*
ns
2
3
4
5
8
9
10
11
Delay time, ECLKOUTx high to BEx valid
1.3
Delay time, ECLKOUTx high to EAx valid
ns
6.4
ns
ns
6.4
ns
6.4
ns
ns
14
td(EKO1H-PDTV)
Delay time, ECLKOUTx high to PDT valid
1.3
6.4
ns
*This parameter is not production tested.
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
94
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
READ
ECLKOUTx
1
1
CEx
2
BE1
ABE[7:0] or BBE[1:0]
AEA[22:14] or BEA[20:12]
AEA[12:3] or BEA[10:1]
4
Bank
5
4
Column
5
4
3
BE2
BE3
BE4
5
AEA13 or BEA11
6
D1
AED[63:0] or BED[15:0]
7
D2
D3
D4
AOE/SDRAS/SOE‡
8
8
ARE/SDCAS/SADS/SRE‡
AWE/SDWE/SWE‡
14
14
PDT§
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
‡ ARE/SDCAS/SADS/SRE, AWE/SDWE/SWE, and AOE/SDRAS/SOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
§ PDT signal is only asserted when the EDMA is in PDT mode (set the PDTS bit to 1 in the EDMA options parameter RAM). For PDT read, data
is not latched into EMIF. The PDTRL field in the PDT control register (PDTCTL) configures the latency of the PDT signal with respect to the data
phase of a read transaction. The latency of the PDT signal for a read can be programmed to 0, 1, 2, or 3 by setting PDTRL to 00, 01, 10, or 11,
respectively. PDTRL equals 00 (zero latency) in Figure 27.
Figure 27. SDRAM Read Command (CAS Latency 3) for EMIFA and EMIFB†
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
95
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
WRITE
ECLKOUTx
1
2
CEx
2
3
4
ABE[7:0] or BBE[1:0]
BE1
4
BE2
BE3
BE4
D2
D3
D4
5
Bank
AEA[22:14] or BEA[20:12]
4
5
Column
AEA[12:3] or BEA[10:1]
4
5
AEA13 or BEA11
9
AED[63:0] or BED[15:0]
10
9
D1
AOE/SDRAS/SOE‡
8
8
11
11
ARE/SDCAS/SADS/SRE‡
AWE/SDWE/SWE‡
14
14
PDT§
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
‡ ARE/SDCAS/SADS/SRE, AWE/SDWE/SWE, and AOE/SDRAS/SOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
§ PDT signal is only asserted when the EDMA is in PDT mode (set the PDTD bit to 1 in the EDMA options parameter RAM). For PDT write, data
is not driven (in High-Z). The PDTWL field in the PDT control register (PDTCTL) configures the latency of the PDT signal with respect to the data
phase of a write transaction. The latency of the PDT signal for a write transaction can be programmed to 0, 1, 2, or 3 by setting PDTWL to 00,
01, 10, or 11, respectively. PDTWL equals 00 (zero latency) in Figure 28.
Figure 28. SDRAM Write Command for EMIFA and EMIFB†
96
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
ACTV
ECLKOUTx
1
1
CEx
ABE[7:0] or BBE[1:0]
4
Bank Activate
5
AEA[22:14] or BEA[20:12]
4
Row Address
5
AEA[12:3] or BEA[10:1]
4
Row Address
5
AEA13 or BEA11
AED[63:0] or BED[15:0]
12
12
AOE/SDRAS/SOE‡
ARE/SDCAS/SADS/SRE‡
AWE/SDWE/SWE‡
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
‡ ARE/SDCAS/SADS/SRE, AWE/SDWE/SWE, and AOE/SDRAS/SOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 29. SDRAM ACTV Command for EMIFA and EMFB†
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
97
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
DCAB
ECLKOUTx
1
1
4
5
12
12
11
11
CEx
ABE[7:0] or BBE[1:0]
AEA[22:14, 12:3] or
BEA[20:12, 10:1]
AEA13 or BEA11
AED[63:0] or BED[15:0]
AOE/SDRAS/SOE‡
ARE/SDCAS/SADS/SRE‡
AWE/SDWE/SWE‡
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
‡ ARE/SDCAS/SADS/SRE, AWE/SDWE/SWE, and AOE/SDRAS/SOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 30. SDRAM DCAB Command for EMIFA and EMIFB†
98
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
DEAC
ECLKOUTx
1
1
CEx
ABE[7:0] or BBE[1:0]
4
5
Bank
AEA[22:14] or BEA[20:12]
AEA[12:3] or BEA[10:1]
4
5
12
12
11
11
AEA13 or BEA11
AED[63:0] or BED[15:0]
AOE/SDRAS/SOE‡
ARE/SDCAS/SADS/SRE‡
AWE/SDWE/SWE‡
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
‡ ARE/SDCAS/SADS/SRE, AWE/SDWE/SWE, and AOE/SDRAS/SOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 31. SDRAM DEAC Command for EMIFA and EMIFB†
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
99
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
REFR
ECLKOUTx
1
1
12
12
8
8
CEx
ABE[7:0] or BBE[1:0]
AEA[22:14, 12:3] or
BEA[20:12, 10:1]
AEA13 or BEA11
AED[63:0] or BED[15:0]
AOE/SDRAS/SOE‡
ARE/SDCAS/SADS/SRE‡
AWE/SDWE/SWE‡
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
‡ ARE/SDCAS/SADS/SRE, AWE/SDWE/SWE, and AOE/SDRAS/SOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 32. SDRAM REFR Command for EMIFA and EMIFB†
100
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
MRS
ECLKOUTx
1
1
4
MRS value
5
12
12
8
8
11
11
CEx
ABE[7:0] or BBE[1:0]
AEA[22:3] or BEA[20:1]
AED[63:0] or BED[15:0]
AOE/SDRAS/SOE‡
ARE/SDCAS/SADS/SRE‡
AWE/SDWE/SWE‡
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
‡ ARE/SDCAS/SADS/SRE, AWE/SDWE/SWE, and AOE/SDRAS/SOE operate as SDCAS, SDWE, and SDRAS, respectively, during SDRAM
accesses.
Figure 33. SDRAM MRS Command for EMIFA and EMIFB†
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
101
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
SYNCHRONOUS DRAM TIMING (CONTINUED)
≥ TRAS cycles
End Self-Refresh
Self Refresh
AECLKOUTx
ACEx
ABE[7:0]
AEA[22:14, 12:3]
AEA13
AED[63:0]
AAOE/ASDRAS/ASOE‡
AARE/ASDCAS/ASADS/
ASRE‡
AAWE/ASDWE/ASWE‡
13
13
ASDCKE
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., the synchronous DRAM
memory access signals are shown as generic ( SDCAS, SDWE, and SDRAS ) instead of ASDCAS, ASDWE, and ASDRAS (for EMIFA) and
BSDCAS, BSDWE, and BSDRAS (for EMIFB)].
‡ AARE/ASDCAS/ASADS/ASRE, AAWE/ASDWE/ASWE, and AAOE/ASDRAS/ASOE operate as ASDCAS, ASDWE, and ASDRAS,
respectively, during SDRAM accesses.
Figure 34. SDRAM Self-Refresh Timing for EMIFA Only†
102
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
HOLD/HOLDA TIMING
timing requirements for the HOLD/HOLDA cycles for EMIFA and EMIFB modules† (see Figure 35)
NO.
MIN
3
toh(HOLDAL-HOLDL) Hold time, HOLD low after HOLDA low
*This parameter is not production tested.
† E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
MAX
E*
UNIT
ns
switching characteristics over recommended operating conditions for the HOLD/HOLDA cycles
for EMIFA and EMIFB modules†‡§ (see Figure 35)
NO.
1
2
4
5
6
7
PARAMETER
MIN
2E*
MAX
¶*
0*
2E*
ns
2E*
7E*
ns
Delay time, EMIF Bus low impedance to HOLDA high
0*
2E*
2E*
¶*
ns
Delay time, HOLD low to ECLKOUTx high impedance
Delay time, HOLD high to ECLKOUTx low impedance
2E*
7E*
ns
td(HOLDL-EMHZ)
td(EMHZ-HOLDAL)
Delay time, HOLD low to EMIF Bus high impedance
td(HOLDH-EMLZ)
td(EMLZ-HOLDAH)
Delay time, HOLD high to EMIF Bus low impedance
td(HOLDL-EKOHZ)
td(HOLDH-EKOLZ)
Delay time, EMIF Bus high impedance to HOLDA low
UNIT
ns
ns
*This parameter is not production tested.
† E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
‡ For EMIFA, EMIF Bus consists of: ACE[3:0], ABE[7:0], AED[63:0], AEA[22:3], AARE/ASDCAS/ASADS/ASRE, AAOE/ASDRAS/ASOE, and
AAWE/ASDWE/ASWE , ASDCKE, ASOE3, and APDT.
For EMIFB, EMIF Bus consists of: BCE[3:0], BBE[1:0], BED[15:0], BEA[20:1], BARE/BSDCAS/BSADS/BSRE, BAOE/BSDRAS/BSOE, and
BAWE/BSDWE/BSWE, BSOE3, and BPDT.
§ The EKxHZ bits in the EMIF Global Control register (GBLCTL) determine the state of the ECLKOUTx signals during HOLDA. If EKxHZ = 0,
ECLKOUTx continues clocking during Hold mode. If EKxHZ = 1, ECLKOUTx goes to high impedance during Hold mode, as shown in Figure 35.
¶ All pending EMIF transactions are allowed to complete before HOLDA is asserted. If no bus transactions are occurring, then the minimum delay
time can be achieved. Also, bus hold can be indefinitely delayed by setting NOHOLD = 1.
External Requestor
Owns Bus
DSP Owns Bus
DSP Owns Bus
3
HOLD
2
5
HOLDA
EMIF Bus†
1
4
C64x
C64x
ECLKOUTx‡
(EKxHZ = 0)
ECLKOUTx‡
(EKxHZ = 1)
6
7
† For EMIFA, EMIF Bus consists of: ACE[3:0], ABE[7:0], AED[63:0], AEA[22:3], AARE/ASDCAS/ASADS/ASRE, AAOE/ASDRAS/ASOE, and
AAWE/ASDWE/ASWE, ASDCKE, ASOE3, and APDT.
For EMIFB, EMIF Bus consists of: BCE[3:0], BBE[1:0], BED[15:0], BEA[20:1], BARE/BSDCAS/BSADS/BSRE, BAOE/BSDRAS/BSOE, and
BAWE/BSDWE/BSWE, BSOE3, and BPDT.
‡ The EKxHZ bits in the EMIF Global Control register (GBLCTL) determine the state of the ECLKOUTx signals during HOLDA. If EKxHZ = 0,
ECLKOUTx continues clocking during Hold mode. If EKxHZ = 1, ECLKOUTx goes to high impedance during Hold mode, as shown in Figure 35.
Figure 35. HOLD/HOLDA Timing for EMIFA and EMIFB
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
103
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
BUSREQ TIMING
switching characteristics over recommended operating conditions for the BUSREQ cycles
for EMIFA and EMIFB modules (see Figure 36)
NO.
1
2
PARAMETER
td(AEKO1H-ABUSRV)
td(BEKO1H-BBUSRV)
MIN
MAX
Delay time, AECLKOUTx high to ABUSREQ valid
1
5.5
ns
Delay time, BECLKOUTx high to BBUSREQ valid
0.9
5.5
ns
ECLKOUTx
1
1
2
2
ABUSREQ
BBUSREQ
Figure 36. BUSREQ Timing for EMIFA and EMIFB
104
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
UNIT
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
RESET TIMING
timing requirements for reset† (see Figure 37)
NO.
MIN
UNIT
10P*
ns
250*
µs
4P*
ns
4P*
ns
1
tw(RST)
Width of the RESET pulse (PLL needs to sync up)§
16
tsu(boot)
th(boot)
Setup time, boot configuration bits valid before RESET high¶
Hold time, boot configuration bits valid after RESET high¶
17
MAX
Width of the RESET pulse (PLL stable)‡
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ This parameter applies to CLKMODE x1 when CLKIN is stable, and applies to CLKMODE x6, x12 when CLKIN and PLL are stable.
§ This parameter applies to CLKMODE x6, x12 only (it does not apply to CLKMODE x1). The RESET signal is not connected internally to the clock
PLL circuit. The PLL, however, may need up to 250 µs to stabilize following device power up or after PLL configuration has been changed. During
that time, RESET must be asserted to ensure proper device operation. See the clock PLL section for PLL lock times.
¶ EMIFB address pins BEA[20:13, 11, 7] are the boot configuration pins during device reset.
switching characteristics over recommended operating conditions during reset†#|| (see Figure 37)
NO.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PARAMETER
MIN
MAX
UNIT
td(RSTL-ECKI)
td(RSTH-ECKI)
Delay time, RESET low to ECLKIN synchronized internally
2E*
3P + 20E*
ns
Delay time, RESET high to ECLKIN synchronized internally
2E*
8P + 20E*
ns
td(RSTL-ECKO1HZ)
td(RSTH-ECKO1V)
Delay time, RESET low to ECLKOUT1 high impedance
2E*
td(RSTL-EMIFZHZ)
td(RSTH-EMIFZV)
Delay time, RESET low to EMIF Z high impedance
td(RSTL-EMIFHIV)
td(RSTH-EMIFHV)
Delay time, RESET low to EMIF high group invalid
td(RSTL-EMIFLIV)
td(RSTH-EMIFLV)
Delay time, RESET low to EMIF low group invalid
td(RSTL-LOWIV)
td(RSTH-LOWV)
Delay time, RESET low to low group invalid
td(RSTL-ZHZ)
td(RSTH-ZV)
Delay time, RESET low to Z group high impedance
Delay time, RESET high to ECLKOUT1 valid
Delay time, RESET high to EMIF Z valid
8P + 20E*
ns
2E*
3P + 4E*
ns
16E*
8P + 20E*
ns
2E*
Delay time, RESET high to EMIF high group valid
ns
8P + 20E*
2E*
Delay time, RESET high to EMIF low group valid
0*
ns
ns
11P*
0*
2P*
ns
ns
8P + 20E*
Delay time, RESET high to low group valid
Delay time, RESET high to Z group valid
ns
ns
ns
8P*
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
# E = the EMIF input clock (ECLKIN, CPU/4 clock, or CPU/6 clock) period in ns for EMIFA or EMIFB.
|| EMIF Z group consists of:
AEA[22:3], BEA[20:1], AED[63:0], BED[15:0], CE[3:0], ABE[7:0], BBE[1:0], ARE/SDCAS/SADS/SRE,
AWE/SDWE/SWE, and AOE/SDRAS/SOE, SOE3, ASDCKE, and PDT.
EMIF high group consists of: AHOLDA and BHOLDA (when the corresponding HOLD input is high)
EMIF low group consists of: ABUSREQ and BBUSREQ; AHOLDA and BHOLDA (when the corresponding HOLD input is low)
Low group consists of:
XSP_CS, CLKX2/XSP_CLK, and DX2/XSP_DO; all of which apply only when PCI EEPROM (BEA13)
is enabled (with PCI_EN = 1 and MCBSP2_EN = 0). Otherwise, the CLKX2/XSP_CLK and DX2/XSP_DO
pins are in the Z group. For more details on the PCI configuration pins, see the Device Configurations section
of this data sheet.
Z group consists of:
HD[31:0]/AD[31:0], CLKX0, CLKX1/URADDR4, CLKX2/XSP_CLK, FSX0, FSX1/UXADDR3, FSX2, DX0,
DX1/UXADDR4, DX2/XSP_DO, CLKR0, CLKR1/URADDR2, CLKR2, FSR0, FSR1/UXADDR2, FSR2,
TOUT0, TOUT1, TOUT2, GP[8:0], GP10/PCBE3, HR/W/PCBE2, HDS2/PCBE1, PCBE0, GP13/PINTA,
GP11/PREQ, HDS1/PSERR, HCS/PPERR, HCNTL1/PDEVSEL, HAS/PPAR, HCNTL0/PSTOP,
HHWIL/PTRDY (16-bit HPI mode only), HRDY/PIRDY, HINT/PFRAME, UXDATA[7:0], UXSOC, UXCLAV,
and URCLAV.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
105
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
RESET TIMING (CONTINUED)
CLKOUT4
CLKOUT6
1
RESET
2
3
4
5
6
7
ECLKIN
ECLKOUT1
ECLKOUT2
EMIF Z Group‡§
8
9
10
11
EMIF High Group‡
EMIF Low Group‡
12
13
14
15
Low Group‡
Z Group‡§
17
16
Boot and Device
Configuration Inputs§¶
† These C64x devices have two EMIFs (EMIFA and EMIFB). All EMIFA signals are prefixed by an “A” and all EMIFB signals are prefixed by a
“B”. Throughout the rest of this document, in generic EMIF areas of discussion, the prefix “A” or “B” may be omitted [e.g., ECLKIN, ECLKOUT1,
and ECLKOUT2].
‡ EMIF Z group consists of:
AEA[22:3], BEA[20:1], AED[63:0], BED[15:0], CE[3:0], ABE[7:0], BBE[1:0], ARE/SDCAS/SADS/SRE,
AWE/SDWE/SWE, and AOE/SDRAS/SOE, SOE3, ASDCKE, and PDT.
EMIF high group consists of: AHOLDA and BHOLDA (when the corresponding HOLD input is high)
EMIF low group consists of: ABUSREQ and BBUSREQ; AHOLDA and BHOLDA (when the corresponding HOLD input is low)
Low group consists of:
XSP_CS, CLKX2/XSP_CLK, and DX2/XSP_DO; all of which apply only when PCI EEPROM (BEA13)
is enabled (with PCI_EN = 1 and MCBSP2_EN = 0). Otherwise, the CLKX2/XSP_CLK and DX2/XSP_DO
pins are in the Z group. For more details on the PCI configuration pins, see the Device Configurations section
of this data sheet.
Z group consists of:
HD[31:0]/AD[31:0], CLKX0, CLKX1/URADDR4, CLKX2/XSP_CLK, FSX0, FSX1/UXADDR3, FSX2, DX0,
DX1/UXADDR4, DX2/XSP_DO, CLKR0, CLKR1/URADDR2, CLKR2, FSR0, FSR1/UXADDR2, FSR2,
TOUT0, TOUT1, TOUT2, GP[8:0], GP10/PCBE3, HR/W/PCBE2, HDS2/PCBE1, PCBE0, GP13/PINTA,
GP11/PREQ, HDS1/PSERR, HCS/PPERR, HCNTL1/PDEVSEL, HAS/PPAR, HCNTL0/PSTOP,
HHWIL/PTRDY (16-bit HPI mode only), HRDY/PIRDY, HINT/PFRAME, UXDATA[7:0], UXSOC, UXCLAV,
and URCLAV.
§ If BEA[20:13, 11, 7] and HD5/AD5 pins are actively driven, care must be taken to ensure no timing contention between parameters 6, 7, 14, 15,
16, and 17.
¶ Boot and Device Configurations Inputs (during reset) include: EMIFB address pins BEA[20:13, 11, 7] and HD5/AD5.
The PCI_EN pin must be driven valid at all times and the user must not switch values throughout device operation.
The MCBSP2_EN pin must be driven valid at all times and the user can switch values throughout device operation.
Figure 37. Reset Timing†
106
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
EXTERNAL INTERRUPT TIMING
timing requirements for external interrupts† (see Figure 38)
MIN
1
2
tw(ILOW)
tw(IHIGH)
MAX
Width of the NMI interrupt pulse low
4P*
ns
Width of the EXT_INT interrupt pulse low
8P*
ns
Width of the NMI interrupt pulse high
4P*
ns
Width of the EXT_INT interrupt pulse high
8P*
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
1
2
EXT_INTx, NMI
Figure 38. External/NMI Interrupt Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
107
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
HOST-PORT INTERFACE (HPI) TIMING
timing requirements for host-port interface cycles†‡ (see Figure 39 through Figure 46)
NO.
1
2
3
4
10
11
12
13
MIN
tsu(SELV-HSTBL)
th(HSTBL-SELV)
Setup time, select signals§ valid before HSTROBE low
Hold time, select signals§ valid after HSTROBE low
tw(HSTBL)
tw(HSTBH)
Pulse duration, HSTROBE low
tsu(HDV-HSTBH)
th(HSTBH-HDV)
14
th(HRDYL-HSTBL)
18
tsu(HASL-HSTBL)
th(HSTBL-HASL)
19
UNIT
5
ns
2.4
4P¶*
ns
4P*
ns
5
ns
Hold time, select signals§ valid after HAS low
2
ns
Setup time, host data valid before HSTROBE high
5
ns
Hold time, host data valid after HSTROBE high
2.8
ns
Hold time, HSTROBE low after HRDY low. HSTROBE should not be
inactivated until HRDY is active (low); otherwise, HPI writes will not complete
properly.
2*
ns
2
ns
2.1
ns
Pulse duration, HSTROBE high between consecutive accesses
Setup time, select signals§ valid before HAS low
tsu(SELV-HASL)
th(HASL-SELV)
MAX
Setup time, HAS low before HSTROBE low
Hold time, HAS low after HSTROBE low
ns
*This parameter is not production tested.
† HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
‡ P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
§ Select signals include: HCNTL[1:0] and HR/W. For HPI16 mode only, select signals also include HHWIL.
¶ Select the parameter value of 4P or 12.5 ns, whichever is greater.
switching characteristics over recommended operating conditions during host-port interface
cycles†‡ (see Figure 39 through Figure 46)
NO.
PARAMETER
MIN
MAX
1.3
4P + 8
UNIT
6
td(HSTBL-HRDYH)
Delay time, HSTROBE low to HRDY high#
7
td(HSTBL-HDLZ)
Delay time, HSTROBE low to HD low impedance for an
HPI read
2*
ns
8
Delay time, HD valid to HRDY low
−3
ns
9
td(HDV-HRDYL)
toh(HSTBH-HDV)
Output hold time, HD valid after HSTROBE high
1.5
15
td(HSTBH-HDHZ)
Delay time, HSTROBE high to HD high impedance
ns
ns
12*
ns
16
td(HSTBL-HDV) Delay time, HSTROBE low to HD valid (HPI16 only)
4P + 8
ns
*This parameter is not production tested.
† HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
‡ P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
# This parameter is used during HPID reads and writes. For reads, at the beginning of a word transfer (HPI32) or the first half-word transfer (HPI16)
on the falling edge of HSTROBE, the HPI sends the request to the EDMA internal address generation hardware, and HRDY remains high until
the EDMA internal address generation hardware loads the requested data into HPID. For writes, HRDY goes high if the internal write buffer is
full.
108
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
HOST-PORT INTERFACE (HPI) TIMING (CONTINUED)
HAS
1
1
2
2
HCNTL[1:0]
1
1
2
2
HR/W
1
1
2
2
HHWIL
4
3
HSTROBE†
3
HCS
15
9
7
15
9
16
HD[15:0] (output)
1st half-word
6
2nd half-word
8
HRDY
† HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 39. HPI16 Read Timing (HAS Not Used, Tied High)
HAS†
19
11
19
10
11
10
HCNTL[1:0]
11
11
10
10
HR/W
11
11
10
10
HHWIL
4
3
HSTROBE‡
18
18
HCS
15
7
9
15
16
9
HD[15:0] (output)
6
1st half-word
8
2nd half-word
HRDY
† For correct operation, strobe the HAS signal only once per HSTROBE active cycle.
‡ HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 40. HPI16 Read Timing (HAS Used)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
109
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
HOST-PORT INTERFACE (HPI) TIMING (CONTINUED)
HAS
1
1
2
2
HCNTL[1:0]
1
1
2
2
HR/W
1
1
2
2
HHWIL
3
3
4
HSTROBE†
HCS
12
12
13
13
HD[15:0] (input)
1st half-word
2nd half-word
6
14
HRDY
† HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 41. HPI16 Write Timing (HAS Not Used, Tied High)
19
HAS†
19
11
11
10
10
HCNTL[1:0]
11
11
10
10
HR/W
11
11
10
10
HHWIL
3
4
HSTROBE‡
18
18
HCS
12
13
12
HD[15:0] (input)
1st half-word
6
2nd half-word
14
HRDY
† For correct operation, strobe the HAS signal only once per HSTROBE active cycle.
‡ HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 42. HPI16 Write Timing (HAS Used)
110
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
13
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
HOST-PORT INTERFACE (HPI) TIMING (CONTINUED)
HAS
1
2
1
2
HCNTL[1:0]
HR/W
3
HSTROBE†
HCS
7
9
15
HD[31:0] (output)
6
8
HRDY
† HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 43. HPI32 Read Timing (HAS Not Used, Tied High)
19
HAS†
11
10
HCNTL[1:0]
11
10
HR/W
18
3
HSTROBE‡
HCS
7
9
15
HD[31:0] (output)
6
8
HRDY
† For correct operation, strobe the HAS signal only once per HSTROBE active cycle.
‡ HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 44. HPI32 Read Timing (HAS Used)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
111
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
HOST-PORT INTERFACE (HPI) TIMING (CONTINUED)
HAS
1
2
1
2
HCNTL[1:0]
HR/W
3
HSTROBE†
HCS
12
13
HD[31:0] (input)
6
14
HRDY
† HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 45. HPI32 Write Timing (HAS Not Used, Tied High)
19
HAS†
11
10
HCNTL[1:0]
11
10
HR/W
3
18
HSTROBE‡
HCS
12
13
HD[31:0] (input)
6
14
HRDY
† For correct operation, strobe the HAS signal only once per HSTROBE active cycle.
‡ HSTROBE refers to the following logical operation on HCS, HDS1, and HDS2: [NOT(HDS1 XOR HDS2)] OR HCS.
Figure 46. HPI32 Write Timing (HAS Used)
112
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
PERIPHERAL COMPONENT INTERCONNECT (PCI) TIMING [C6415 AND C6416 ONLY]
timing requirements for PCLK†‡ (see Figure 47)
NO.
1
2
3
4
MIN
30 (or 8P§)*
tc(PCLK)
tw(PCLKH)
Cycle time, PCLK
Pulse duration, PCLK high
11*
tw(PCLKL)
tsr(PCLK)
Pulse duration, PCLK low
11*
∆v/∆t slew rate, PCLK
1*
MAX
UNIT
ns
ns
ns
4*
V/ns
*This parameter is not production tested.
† For 3.3-V operation, the reference points for the rise and fall transitions are measured at VILP MAX and VIHP MIN.
‡ P = 1/CPU clock frequency in ns. For example when running parts at 600 MHz, use P = 1.67 ns.
§ Select the parameter value of 30 ns or 8P, whichever is greater.
1
0.4 DVDD V MIN
Peak to Peak for
3.3V signaling
4
2
PCLK
3
4
Figure 47. PCLK Timing
timing requirements for PCI reset (see Figure 48)
NO.
1
2
MIN
tw(PRST)
tsu(PCLKA-PRSTH)
Pulse duration, PRST
Setup time, PCLK active before PRST high
MAX
UNIT
1*
ms
100*
µs
*This parameter is not production tested.
PCLK
1
PRST
2
Figure 48. PCI Reset (PRST) Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
113
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
PERIPHERAL COMPONENT INTERCONNECT (PCI) TIMING [C6415 AND C6416 ONLY]
(CONTINUED)
timing requirements for PCI inputs (see Figure 49)
NO.
5
6
MIN
tsu(IV-PCLKH)
th(IV-PCLKH)
MAX
UNIT
Setup time, input valid before PCLK high
7
ns
Hold time, input valid after PCLK high
0
ns
switching characteristics over recommended operating conditions for PCI outputs (see Figure 49)
NO.
1
2
3
4
PARAMETER
MIN
td(PCLKH-OV)
td(PCLKH-OIV)
Delay time, PCLK high to output valid
td(PCLKH-OLZ)
td(PCLKH-OHZ)
Delay time, PCLK high to output low impedance
11
Delay time, PCLK high to output invalid
Delay time, PCLK high to output high impedance
PCLK
1
2
Valid
PCI Output
3
4
Valid
PCI Input
5
6
Figure 49. PCI Input/Output Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
UNIT
ns
2
ns
2*
ns
28*
*This parameter is not production tested.
114
MAX
ns
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
PERIPHERAL COMPONENT INTERCONNECT (PCI) TIMING [C6415 AND C6416 ONLY]
(CONTINUED)
timing requirements for serial EEPROM interface (see Figure 50)
NO.
8
MIN
tsu(DIV-CLKH)
th(CLKH-DIV)
9
Setup time, XSP_DI valid before XSP_CLK high
Hold time, XSP_DI valid after XSP_CLK high
MAX
UNIT
50*
ns
0*
ns
*This parameter is not production tested.
switching characteristics over recommended operating conditions for serial EEPROM interface†
(see Figure 50)
NO.
1
2
3
4
5
6
PARAMETER
tw(CSL)
td(CLKL-CSL)
Pulse duration, XSP_CS low
td(CSH-CLKH)
tw(CLKH)
tw(CLKL)
tosu(DOV-CLKH)
MIN
TYP
MAX
UNIT
4092P
ns
0
ns
Delay time, XSP_CS high to XSP_CLK high
2046P
ns
Pulse duration, XSP_CLK high
2046P
ns
Pulse duration, XSP_CLK low
2046P
ns
Output setup time, XSP_DO valid after XSP_CLK high
2046P
ns
2046P
ns
Delay time, XSP_CLK low to XSP_CS low
7
toh(CLKH-DOV)
Output hold time, XSP_DO valid after XSP_CLK high
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
2
1
XSP_CS
3
4
5
XSP_CLK
6
7
XSP_DO
8
9
XSP_DI
Figure 50. PCI Serial EEPROM Interface Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
115
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
MULTICHANNEL BUFFERED SERIAL PORT (McBSP) TIMING
timing requirements for McBSP† (see Figure 51)
NO.
2
3
tc(CKRX)
tw(CKRX)
Cycle time, CLKR/X
CLKR/X ext
Pulse duration, CLKR/X high or CLKR/X low
5
tsu(FRH-CKRL)
Setup time, external FSR high before CLKR low
6
th(CKRL-FRH)
Hold time, external FSR high after CLKR low
7
tsu(DRV-CKRL)
Setup time, DR valid before CLKR low
8
th(CKRL-DRV)
Hold time, DR valid after CLKR low
10
tsu(FXH-CKXL)
Setup time, external FSX high before CLKX low
11
th(CKXL-FXH)
Hold time, external FSX high after CLKX low
CLKR/X ext
MIN
6.67‡*
0.5tc(CKRX) −1§*
CLKR int
9
CLKR ext
1.3
CLKR int
6
CLKR ext
3
CLKR int
8
CLKR ext
0.9
CLKR int
3
CLKR ext
3.1
CLKX int
9
CLKX ext
1.3
CLKX int
6
CLKX ext
3
MAX
UNIT
ns
ns
ns
ns
ns
ns
ns
ns
*This parameter is not production tested.
† CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
‡ Minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and ac timing
requirements.
§ This parameter applies to the maximum McBSP frequency. Operate serial clocks (CLKR/X) in the reasonable range of 40/60 duty cycle.
116
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
MULTICHANNEL BUFFERED SERIAL PORT (McBSP) TIMING (CONTINUED)
switching characteristics over recommended operating conditions for McBSP†‡ (see Figure 51)
NO.
PARAMETER
Delay time, CLKS high to CLKR/X high for internal CLKR/X generated
from CLKS input
MIN
MAX
1.4
10
6.67§*
C − 1¶*
C + 1¶*
ns
ns
1
td(CKSH-CKRXH)
2
Cycle time, CLKR/X
3
tc(CKRX)
tw(CKRX)
Pulse duration, CLKR/X high or CLKR/X low
CLKR/X int
4
td(CKRH-FRV)
Delay time, CLKR high to internal FSR valid
CLKR int
−2.1
3
CLKX int
−1.7
3
CLKX ext
1.7
9
CLKX int
−3.9*
4*
CLKX ext
CLKX int
−2.1*
−3.9 + D1#
9*
4 + D2#
CLKX ext
−2.1 + D1#
9 + D2#
CLKR/X int
9
td(CKXH-FXV)
Delay time, CLKX high to internal FSX valid
12
tdis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit
from CLKX high
13
td(CKXH-DXV)
Delay time, CLKX high to DX valid
14
td(FXH-DXV)
UNIT
ns
ns
Delay time, FSX high to DX valid
FSX int
−2.3
5.6
ONLY applies when in data
delay 0 (XDATDLY = 00b) mode
FSX ext
1.9
9
ns
ns
ns
ns
*This parameter is not production tested.
† CLKRP = CLKXP = FSRP = FSXP = 0. If polarity of any of the signals is inverted, then the timing references of that signal are also inverted.
‡ Minimum delay times also represent minimum output hold times.
§ Minimum CLKR/X cycle times are based on internal logic speed; the maximum usable speed may be lower due to EDMA limitations and AC timing
requirements.
¶ C = H or L
S = sample rate generator input clock = 4P if CLKSM = 1 (P = 1/CPU clock frequency)
= sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
CLKGDV should be set appropriately to ensure the McBSP bit rate does not exceed the maximum limit (see ¶ footnote above).
# Extra delay from CLKX high to DX valid applies only to the first data bit of a device, if and only if DXENA = 1 in SPCR.
if DXENA = 0, then D1 = D2 = 0
if DXENA = 1, then D1 = 4P, D2 = 8P
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
117
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
MULTICHANNEL BUFFERED SERIAL PORT (McBSP) TIMING (CONTINUED)
CLKS
1
2
3
3
CLKR
4
4
FSR (int)
5
6
FSR (ext)
7
DR
8
Bit(n-1)
(n-2)
(n-3)
2
3
3
CLKX
9
FSX (int)
11
10
FSX (ext)
FSX (XDATDLY=00b)
12
DX
Bit 0
14
13
Bit(n-1)
13
(n-2)
Figure 51. McBSP Timing
118
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
(n-3)
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
MULTICHANNEL BUFFERED SERIAL PORT (McBSP) TIMING (CONTINUED)
timing requirements for FSR when GSYNC = 1 (see Figure 52)
NO.
1
2
MIN
tsu(FRH-CKSH)
th(CKSH-FRH)
MAX
UNIT
Setup time, FSR high before CLKS high
4*
ns
Hold time, FSR high after CLKS high
4*
ns
*This parameter is not production tested.
CLKS
1
2
FSR external
CLKR/X (no need to resync)
CLKR/X (needs resync)
Figure 52. FSR Timing When GSYNC = 1
timing requirements for McBSP as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0†‡ (see Figure 53)
MASTER
NO.
4
MIN
tsu(DRV-CKXL)
th(CKXL-DRV)
Setup time, DR valid before CLKX low
MAX
12
5
Hold time, DR valid after CLKX low
4
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SLAVE
MIN
MAX
UNIT
2 − 12P
ns
5 + 24P
ns
119
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
switching characteristics over recommended operating conditions for McBSP as SPI Master or
Slave: CLKSTP = 10b, CLKXP = 0†‡ (see Figure 53)
MASTER§
NO.
PARAMETER
MIN
2
th(CKXL-FXL)
td(FXL-CKXH)
Hold time, FSX low after CLKX low¶
Delay time, FSX low to CLKX high#
3
td(CKXH-DXV)
Delay time, CLKX high to DX valid
6
tdis(CKXL-DXHZ)
Disable time, DX high impedance following last data bit
from CLKX low
7
tdis(FXH-DXHZ)
Disable time, DX high impedance following last data bit
from FSX high
1
SLAVE
MAX
T−2
T+3
L − 2*
L + 3*
−2
4
L − 2*
L + 3*
MIN
MAX
UNIT
ns
ns
12P + 2.8
20P + 17
ns
ns
4P + 3*
12P + 17*
8
ns
td(FXL-DXV)
Delay time, FSX low to DX valid
8P + 1.8 16P + 17
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = Sample rate generator input clock = 4P if CLKSM = 1 (P = 1/CPU clock frequency)
= Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
¶ FSRP = FSXP = 1. As a SPI Master, FSX is inverted to provide active-low slave-enable output. As a Slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for Master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for Slave McBSP
# FSX should be low before the rising edge of clock to enable Slave devices and then begin a SPI transfer at the rising edge of the Master clock
(CLKX).
CLKX
1
2
FSX
7
6
DX
8
3
Bit 0
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 53. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 0
120
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
MULTICHANNEL BUFFERED SERIAL PORT (McBSP) TIMING (CONTINUED)
timing requirements for McBSP as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0†‡ (see Figure 54)
MASTER
NO.
4
5
MIN
tsu(DRV-CKXH)
th(CKXH-DRV)
Setup time, DR valid before CLKX high
SLAVE
MAX
MIN
MAX
UNIT
12*
2 − 12P*
ns
4*
5 + 24P*
ns
Hold time, DR valid after CLKX high
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI Master or
Slave: CLKSTP = 11b, CLKXP = 0†‡ (see Figure 54)
MASTER§
NO.
PARAMETER
SLAVE
MIN
MAX
L − 2*
L + 3*
MIN
MAX
UNIT
2
th(CKXL-FXL)
td(FXL-CKXH)
Hold time, FSX low after CLKX low¶
Delay time, FSX low to CLKX high#
T − 2*
T + 3*
3
td(CKXL-DXV)
Delay time, CLKX low to DX valid
−2*
4*
12P + 4*
20P + 17*
ns
6
tdis(CKXL-DXHZ)
Disable time, DX high impedance following last data bit
from CLKX low
−2*
4*
12P + 3*
20P + 17*
ns
1
ns
ns
7
td(FXL-DXV)
Delay time, FSX low to DX valid
H − 2* H + 4*
8P + 2* 16P + 17*
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = Sample rate generator input clock = 4P if CLKSM = 1 (P = 1/CPU clock frequency)
= Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
¶ FSRP = FSXP = 1. As a SPI Master, FSX is inverted to provide active-low slave-enable output. As a Slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for Master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for Slave McBSP
# FSX should be low before the rising edge of clock to enable Slave devices and then begin a SPI transfer at the rising edge of the Master clock
(CLKX).
CLKX
1
2
6
Bit 0
7
FSX
DX
3
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 54. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 0
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
121
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
MULTICHANNEL BUFFERED SERIAL PORT (McBSP) TIMING (CONTINUED)
timing requirements for McBSP as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 55)
MASTER
NO.
4
5
MIN
tsu(DRV-CKXH)
th(CKXH-DRV)
Setup time, DR valid before CLKX high
SLAVE
MAX
MIN
MAX
UNIT
12*
2 − 12P*
ns
4*
5 + 24P*
ns
Hold time, DR valid after CLKX high
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI Master or
Slave: CLKSTP = 10b, CLKXP = 1†‡ (see Figure 55)
MASTER§
NO.
PARAMETER
MIN
2
th(CKXH-FXL)
td(FXL-CKXL)
Hold time, FSX low after CLKX high¶
Delay time, FSX low to CLKX low#
3
td(CKXL-DXV)
Delay time, CLKX low to DX valid
6
tdis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit
from CLKX high
7
tdis(FXH-DXHZ)
Disable time, DX high impedance following last data bit
from FSX high
1
SLAVE
MAX
T − 2*
T + 3*
H − 2*
H + 3*
−2*
4*
H − 2*
H + 3*
MIN
MAX
UNIT
ns
ns
12P + 4*
20P + 17*
ns
ns
4P + 3*
12P + 17*
8
ns
td(FXL-DXV)
Delay time, FSX low to DX valid
8P + 2* 16P + 17*
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = Sample rate generator input clock = 4P if CLKSM = 1 (P = 1/CPU clock frequency)
= Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
¶ FSRP = FSXP = 1. As a SPI Master, FSX is inverted to provide active-low slave-enable output. As a Slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for Master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for Slave McBSP
# FSX should be low before the rising edge of clock to enable Slave devices and then begin a SPI transfer at the rising edge of the Master clock
(CLKX).
CLKX
1
2
FSX
7
6
DX
8
3
Bit 0
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 55. McBSP Timing as SPI Master or Slave: CLKSTP = 10b, CLKXP = 1
122
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
MULTICHANNEL BUFFERED SERIAL PORT (McBSP) TIMING (CONTINUED)
timing requirements for McBSP as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1†‡ (see Figure 56)
MASTER
NO.
4
5
MIN
tsu(DRV-CKXH)
th(CKXH-DRV)
Setup time, DR valid before CLKX high
SLAVE
MAX
MIN
MAX
UNIT
12*
2 − 12P*
ns
4*
5 + 24P*
ns
Hold time, DR valid after CLKX high
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.
switching characteristics over recommended operating conditions for McBSP as SPI Master or
Slave: CLKSTP = 11b, CLKXP = 1†‡ (see Figure 56)
MASTER§
NO.
PARAMETER
SLAVE
MIN
MAX
H − 2*
H + 3*
T − 2*
T + 1*
MIN
MAX
UNIT
2
th(CKXH-FXL)
td(FXL-CKXL)
Hold time, FSX low after CLKX high¶
Delay time, FSX low to CLKX low#
3
td(CKXH-DXV)
Delay time, CLKX high to DX valid
−2*
4*
12P + 4*
20P + 17*
ns
6
tdis(CKXH-DXHZ)
Disable time, DX high impedance following last data bit
from CLKX high
−2*
4*
12P + 3*
20P + 17*
ns
1
ns
ns
7
td(FXL-DXV)
Delay time, FSX low to DX valid
L − 2* L + 4*
8P + 2* 16P + 17*
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ For all SPI Slave modes, CLKG is programmed as 1/4 of the CPU clock by setting CLKSM = CLKGDV = 1.
§ S = Sample rate generator input clock = 4P if CLKSM = 1 (P = 1/CPU clock frequency)
= Sample rate generator input clock = P_clks if CLKSM = 0 (P_clks = CLKS period)
T = CLKX period = (1 + CLKGDV) * S
H = CLKX high pulse width = (CLKGDV/2 + 1) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
L = CLKX low pulse width = (CLKGDV/2) * S if CLKGDV is even
= (CLKGDV + 1)/2 * S if CLKGDV is odd or zero
¶ FSRP = FSXP = 1. As a SPI Master, FSX is inverted to provide active-low slave-enable output. As a Slave, the active-low signal input on FSX
and FSR is inverted before being used internally.
CLKXM = FSXM = 1, CLKRM = FSRM = 0 for Master McBSP
CLKXM = CLKRM = FSXM = FSRM = 0 for Slave McBSP
# FSX should be low before the rising edge of clock to enable Slave devices and then begin a SPI transfer at the rising edge of the Master clock
(CLKX).
CLKX
1
2
FSX
7
6
DX
3
Bit 0
Bit(n-1)
4
DR
Bit 0
(n-2)
(n-3)
(n-4)
5
Bit(n-1)
(n-2)
(n-3)
(n-4)
Figure 56. McBSP Timing as SPI Master or Slave: CLKSTP = 11b, CLKXP = 1
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
123
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
UTOPIA SLAVE TIMING [C6415 AND C6416 ONLY]
timing requirements for UXCLK† (see Figure 57)
NO.
1
2
3
4
MIN
tc(UXCK)
tw(UXCKH)
Cycle time, UXCLK
tw(UXCKL)
tt(UXCK)
Pulse duration, UXCLK low
MAX
20*
Pulse duration, UXCLK high
UNIT
ns
0.4tc(UXCK)*
0.4tc(UXCK)*
Transition time, UXCLK
0.6tc(UXCK)*
0.6tc(UXCK)*
ns
2*
ns
ns
*This parameter is not production tested.
† The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
1
4
2
UXCLK
3
4
Figure 57. UXCLK Timing
timing requirements for URCLK† (see Figure 58)
NO.
1
2
3
4
MIN
tc(URCK)
tw(URCKH)
Cycle time, URCLK
tw(URCKL)
tt(URCK)
Pulse duration, URCLK low
MAX
20*
Pulse duration, URCLK high
ns
0.4tc(URCK)*
0.4tc(URCK)*
Transition time, URCLK
*This parameter is not production tested.
† The reference points for the rise and fall transitions are measured at VIL MAX and VIH MIN.
1
4
URCLK
3
4
Figure 58. URCLK Timing
124
0.6tc(URCK)*
0.6tc(URCK)*
2*
2
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
UNIT
ns
ns
ns
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
UTOPIA SLAVE TIMING [C6415 AND C6416 ONLY] (CONTINUED)
timing requirements for UTOPIA Slave transmit (see Figure 59)
NO.
2
3
8
9
MIN
MAX
UNIT
tsu(UXAV-UXCH)
th(UXCH-UXAV)
Setup time, UXADDR valid before UXCLK high
4
ns
Hold time, UXADDR valid after UXCLK high
1
ns
tsu(UXENBL-UXCH)
th(UXCH-UXENBL)
Setup time, UXENB low before UXCLK high
4
ns
Hold time, UXENB low after UXCLK high
1
ns
switching characteristics over recommended operating conditions for UTOPIA Slave transmit
(see Figure 59)
NO.
1
4
5
6
7
10
MIN
MAX
td(UXCH-UXDV)
td(UXCH-UXCLAV)
Delay time, UXCLK high to UXDATA valid
PARAMETER
3
12
ns
Delay time, UXCLK high to UXCLAV driven active value
3
12
ns
td(UXCH-UXCLAVL)
td(UXCH-UXCLAVHZ)
Delay time, UXCLK high to UXCLAV driven inactive low
3*
12*
ns
Delay time, UXCLK high to UXCLAV going Hi-Z
9*
18.5*
ns
tw(UXCLAVL-UXCLAVHZ)
td(UXCH-UXSV)
Pulse duration (low), UXCLAV low to UXCLAV Hi-Z
3*
Delay time, UXCLK high to UXSOC valid
UNIT
ns
3
12
ns
*This parameter is not production tested.
UXCLK
1
UXDATA[7:0]
P45
P46
P47
P48
H1
3
2
UXADDR[4:0]
0 x1F
N
0x1F
N
0x1F
N+1
0x1F
6
7
4
UXCLAV
5
N
N
9
8
UXENB
10
UXSOC
† The UTOPIA Slave module has signals that are middle-level signals indicating a high-impedance state (i.e., the UXCLAV and
UXSOC signals).
Figure 59. UTOPIA Slave Transmit Timing†
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
125
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
UTOPIA SLAVE TIMING [C6415 AND C6416 ONLY] (CONTINUED)
timing requirements for UTOPIA Slave receive (see Figure 60)
NO.
1
2
3
4
9
10
11
12
MIN
MAX
UNIT
tsu(URDV-URCH)
th(URCH-URDV)
Setup time, URDATA valid before URCLK high
4
ns
Hold time, URDATA valid after URCLK high
1
ns
tsu(URAV-URCH)
th(URCH-URAV)
Setup time, URADDR valid before URCLK high
4
ns
Hold time, URADDR valid after URCLK high
1
ns
tsu(URENBL-URCH)
th(URCH-URENBL)
Setup time, URENB low before URCLK high
4
ns
Hold time, URENB low after URCLK high
1
ns
tsu(URSH-URCH)
th(URCH-URSH)
Setup time, URSOC high before URCLK high
4
ns
Hold time, URSOC high after URCLK high
1
ns
switching characteristics over recommended operating conditions for UTOPIA Slave receive
(see Figure 60)
NO.
MIN
MAX
5
td(URCH-URCLAV)
Delay time, URCLK high to URCLAV driven active value
PARAMETER
3
12
UNIT
ns
6
td(URCH-URCLAVL)
Delay time, URCLK high to URCLAV driven inactive low
3*
12*
ns
7
td(URCH-URCLAVHZ)
Delay time, URCLK high to URCLAV going Hi-Z
9*
18.5*
ns
8
tw(URCLAVL-URCLAVHZ)
Pulse duration (low), URCLAV low to URCLAV Hi-Z
3*
ns
*This parameter is not production tested.
URCLK
2
1
URDATA[7:0]
P48
H1
H2
H3
0x1F
N+2
0x1F
4
3
URADDR[4:0]
N
0x1F
N+1
7
6
5
URCLAV
N
N+1
10
8
N+2
9
URENB
11
12
URSOC
† The UTOPIA Slave module has signals that are middle-level signals indicating a high-impedance state (i.e., the URCLAV and
URSOC signals).
Figure 60. UTOPIA Slave Receive Timing†
126
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
TIMER TIMING
timing requirements for timer inputs† (see Figure 61)
NO.
1
2
MIN
tw(TINPH)
tw(TINPL)
MAX
UNIT
Pulse duration, TINP high
8P*
ns
Pulse duration, TINP low
8P*
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
switching characteristics over recommended operating conditions for timer outputs†
(see Figure 61)
NO.
3
4
PARAMETER
tw(TOUTH)
tw(TOUTL)
MIN
MAX
UNIT
Pulse duration, TOUT high
8P −3*
ns
Pulse duration, TOUT low
8P −3*
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
2
1
TINPx
4
3
TOUTx
Figure 61. Timer Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
127
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
GENERAL-PURPOSE INPUT/OUTPUT (GPIO) PORT TIMING
timing requirements for GPIO inputs†‡ (see Figure 62)
NO.
1
2
MIN
tw(GPIH)
tw(GPIL)
MAX
UNIT
Pulse duration, GPIx high
8P*
ns
Pulse duration, GPIx low
8P*
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
‡ The pulse width given is sufficient to generate a CPU interrupt or an EDMA event. However, if a user wants to have the DSP recognize the GPIx
changes through software polling of the GPIO register, the GPIx duration must be extended to at least 12P to allow the DSP enough time to access
the GPIO register through the CFGBUS.
switching characteristics over recommended operating conditions for GPIO outputs†
(see Figure 62)
NO.
3
4
PARAMETER
tw(GPOH)
tw(GPOL)
MIN
UNIT
32P*
ns
Pulse duration, GPOx low
32P*
ns
*This parameter is not production tested.
† P = 1/CPU clock frequency in ns. For example, when running parts at 600 MHz, use P = 1.67 ns.
2
1
GPIx
4
3
GPOx
Figure 62. GPIO Port Timing
128
MAX
Pulse duration, GPOx high
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
JTAG TEST-PORT TIMING
timing requirements for JTAG test port (see Figure 63)
NO.
1
3
MIN
tc(TCK)
tsu(TDIV-TCKH)
MAX
UNIT
Cycle time, TCK
35*
ns
Setup time, TDI/TMS/TRST valid before TCK high
10*
ns
9*
ns
4
th(TCKH-TDIV)
Hold time, TDI/TMS/TRST valid after TCK high
*This parameter is not production tested.
switching characteristics over recommended operating conditions for JTAG test port
(see Figure 63)
NO.
PARAMETER
2
td(TCKL-TDOV) Delay time, TCK low to TDO valid
*This parameter is not production tested.
MIN
MAX
–3*
18*
UNIT
ns
1
TCK
2
2
TDO
4
3
TDI/TMS/TRST
Figure 63. JTAG Test-Port Timing
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
129
SGUS050A − JANUARY 2004 − REVISED MARCH 2004
MECHANICAL DATA
GAD (S-CPGA-P570)
NOTES: A.
B.
C.
D.
CERAMIC PIN GRID ARRAY
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Flip chip application only
This package is hermetically sealed with a metal lid.
thermal resistance characteristics (S-CPGA package)
°C/W
NO
1
2
3
4
5
6
130
RΘJA
RΘJA
Junction-to-free air (Low K JEDEC PCB)
20.96
Junction-to-free air (High K JEDEC PCB)
16.5
RΘJC
RΘJC
Junction-to-case (High K JEDEC PCB with heat sink on lid)
10.9
Junction-to-case (High K JEDEC PCB with heat sink on body)
7.69
RΘJB
RΘJB
Junction-to-board (High K JEDEC PCB)
9
Junction-to-board (High K JEDEC PCB with thermal compound on top of the die)
POST OFFICE BOX 1443
• HOUSTON, TEXAS 77251−1443
2.93
PACKAGE OPTION ADDENDUM
www.ti.com
28-Jan-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
5962-0324501QXA
ACTIVE
FCPGA
GAD
570
1
TBD
Call TI
N / A for Pkg Type
-55 to 115
(5962-0324501QX ~
5962-0324501QX
A)
(A ~
SMJ320C6415DGA
DW60)
SMJ320C6415DGA
DW60
SM320C6415DGADW60
ACTIVE
FCPGA
GAD
570
8
TBD
Call TI
N / A for Pkg Type
-55 to 115
SM320C6415DGADW60
SM320C6415DGAD
W60
SMJ320C6415DGADW60
ACTIVE
FCPGA
GAD
570
1
TBD
Call TI
N / A for Pkg Type
-55 to 115
(5962-0324501QX ~
5962-0324501QX
A)
(A ~
SMJ320C6415DGA
DW60)
SMJ320C6415DGA
DW60
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
(4)
28-Jan-2016
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF SM320C6415, SMJ320C6414, SMJ320C6415 :
• Catalog: TMS320C6415, TMS320C6414, TMS320C6415
• Enhanced Product: SM320C6415-EP
• Military: SMJ320C6415
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Enhanced Product - Supports Defense, Aerospace and Medical Applications
• Military - QML certified for Military and Defense Applications
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated