KOA SPEER ELECTRONICS, INC. SS-192 R4 AHA 12/19/03 Capacitor/Resistor Chip Networks Type CR2A10Y CERTIFIED 1. Scope This specification shall be applied to CR chip networks CR2A10Y produced by KOA Corporation. 2. Related Standard JIS C 5102 (1994) JIS C 5202 (1994) JIS C 6429 (1991) JIS C 0806 (1990) Test method of fixed capacitors for use in electronic equipment. Test method of fixed resistors for use in electronic equipment. Fixed Multilayer Ceramic Chip capacitors for use in electronic equipment. Packaging of electronic components on continuous tapes (surface mounting devices). 3. Dimensions C C 3-1 Dimensions W D 411 B P L A T D D A D unit: inches (mm) L W C D T .157 ± .008 .083 ± .008 .012 ± .008 .016 ± .006 .028 ± .004 (4.0 ± 0.2) (2.1 ± 0.2) (0.3 ± 0.2) (0.4 ± 0.15) (0.7 ± 0.1) A .02 (0.5 Ref.) B .006 (0.15 Ref.) P .031 (0.8 Ref.) PAGE 1 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-192 R4 3-2. Circuit Schematic 10 9 3-3. Structure 8 7 1 1 3 1 Alumina Ceramic 2 Passivation 3 Ni & Solder Plating 6 411 2 3 4 2 5 4. Type Designation The type designation shall be the following form: CR 2A10 Y TE xxxM/ xxxJ Style Chip Size Circuit Packaging Capacitance Tolerance/Resistance Tolerance CR Chip Networks .157" x .083" 4.0 x 2.1 mm 3 Digit Numbers +1 for Resistance Tolerance for each Ex: 270M/510J TE: Embossed Taping No Designation: Bulk 5. Rating Operating environment -25°C ~ +85°C Capacitor Item Capacitor Rating Resistor Item Resistor Rating 1 KHz ± 10% (1 Vrms ± 0.2V) Power Rating 0.063 W 25V (DC) Maximum Working Voltage 7.9 V Capacitance Tolerance ± 20%/± 30% Maximum Overload Voltage 15.8 V Temperature Coefficient +20%/-55% Temperature Coefficient (-25°C ~ +85°C) ± 200 ppm/°C 3% maximum Resistor Tolerance (at 1 KHz 1.0 Vrms) ± 5% Capacitance Measuring Condition Voltage Rating Dissipation Factor Insulation Resistance 1,000 MΩ minimum Rating Ambient Temperature Dielectric Withstanding Voltage 62.5V DC 5 sec. 50 mA charge Operating Temperature Range -25°C to +85°C Capacitance Range + 70°C Operating Temperature Range -25°C to +85°C Resistor Range 22Ω, 47Ω,100Ω, 220Ω, 470Ω, 1KΩ, 47KΩ 22pF, 47pF, 100pF PAGE 2 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-192 R4 5-2 Rated Voltage The rated voltage is limited to the maximum working voltage. The maximum value DC voltage capable of being applied continuously to a resistor at the rated ambient temperature. Rated voltage shall be calculated from the following formula: Percent Rated Wattage (%) E=√ PxR Power Derating Curve Where: E = Rated voltage (V) P = Rated power (W) R = Nominal resistance (Ω) 120 100 80 60 40 20 0 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Ambient Temperature (°C) 6. Marking 6-1 Apply a mark of 1st terminal for a position of 1st terminal. 6-2 Marking Code Type Capacitance (pF) Resistance (Ω) Marking Code CR2A10YTE220/220J CR2A10YTE220/470J CR2A10YTE220/101J CR2A10YTE220/221J CR2A10YTE220/471J CR2A10YTE220/102J CR2A10YTE470/220J CR2A10YTE470/470J CR2A10YTE470/101J CR2A10YTE470/221J CR2A10YTE470/471J CR2A10YTE470/102J CR2A10YTE101/220J CR2A10YTE101/470J CR2A10YTE101/101J CR2A10YTE101/221J CR2A10YTE101/471J CR2A10YTE101/102J CR2A10YLTE101M/473J 22 22 22 22 22 22 47 47 47 47 47 47 100 100 100 100 100 100 100 22 47 100 220 470 1K 22 47 100 220 470 1K 22 47 100 220 470 1K 47K 120 140 111 121 141 112 220 240 211 221 241 212 420 440 411 421 441 412 443 PAGE 3 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-192 R4 7. Test Condition Unless otherwise specified, the test shall be performed in accordance with JIS-C-5020 specifying at the temperature of 20 °C ± 15°C and at the humidity of 65% ± 20%. In case doubts arise about the test results, the test shall be performed at the temperature of 20°C ± 2°C and at the humidity of 65% ± 5%. 8. Reliability Test 8-1 Electrical Characteristics No. Item Requirement More than 104 MΩ Insulation Resistance 1 Test Methods Within 2 minutes at DC 25V between terminal and another v 2 Dielectric Withstanding Voltage No evidence of fuming flaming or breakdown 2.5 times maximum rated voltage for 5 seconds with 50 mA maximum charging current v PAGE 4 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-192 R4 8-2 Mechanical Characteristics Item No. Requirement Test Methods 1 Resistance to Soldering Heat No evidence of damage ∆C within ± 20% ∆R within ± 5% D. F. within 5% I. R. more than 100 MΩ Immerse in the solder (H63A) of 260°C ± 5°C for 10 ± 1 seconds. Measurement shall be done 24 ± 4 hours at room condition after test. 2 Solderability Approximately 95% of the terminal should be covered with new solder Immerse in the solder (H63A) of 235°C ± 5°C for 3 ± 0.5 seconds. 3 Terminal Strength (Bend test) No mechanical damage Specimen shall be soldered on PCB and support by applying strength so that the bending width becomes 3mm. 4 Resistance to Solvents No mechanical damage Immerse in the IPA of 20 ~ 25°C for 60 ± 10 seconds. 5 Vibration No evidence of damage 2 hours in each direction of X,Y,Z on PCB at a frequency range of 10-55-10Hz with 1.5mm amplitude. Measurement shall be done 24 ± 4 hours at room condition after test. 8-3 Environmental Characteristics No. Item Requirement Test Methods 1 Temperature cycling No evidence of damage ∆C within ± 20% ∆R within ± 5% D.F. within 5% I.R. more than 100 MΩ 100 cycles between - 40°C/30 minutes and +125°C/30 minutes. Measurement shall be done 24 ± 4 hours at room condition after test. 2 Humidity (No Load) No evidence of damage ∆C within ± 20% ∆R within ± 5% D.F. within 5% I.R. more than 100 MΩ MIL-STD-202F Method 106 10 cycles Measurement shall be done 24 ± 4 hours at room condition after test. 3 Moisture Resistance No evidence of damage ∆C within ± 20% ∆R within ± 5% D.F. within 5% I.R. more than 100 MΩ Temperature 40°C ± 2°C Humidity 90% ~ 95% 1000 hours DC 50V 1.5 hours ON 0.5 hours OFF Measurement shall be done 24 ± 4 hours at room condition after test. 4 Load Life No evidence of damage ∆C within ± 20% ∆R within ± 5% D.F. within 5% I.R. more than 100 MΩ Temperature 70°C ± 2°C 1000 hours DC 50V 1.5 hours ON 0.5 hours OFF Measurement shall be done 24 ± 4 hours at room condition after test. PAGE 5 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-192 R4 9. Packaging 9-1 Bulk Packaging 100 pieces chip are packed in a poly bag. The package shall be marked: (1) Type Designation (CR2A10Y) (2) Nominal Capacitance/Nominal Resistance (3 digit/3 digit) (3) Quantity (4) Production Lot. No. (5) Manufacturer’s name 9-2 Taping The taping shall be embossed carrier tapes of 12 mm width and 4 mm pitches. The standard quantity per reel shall be 4000 pieces. (1) Carrier Tape P0 P2 øD E F W B 2nd Terminal T2 P1 A Tape Running Direction T1 (unit: mm) F 5.5 ± 0.1 Type CR2A10Y A 2.5 ± 0.2 B 4.4 ± 0.2 W 12.0 ± 0.2 E 1.75 ± 0.1 T1 T2 P0 P1 P2 øD 1.15 ± 0.2 0.25 ± 0.05 4.0 ± 0.1 4.0 ± 0.1 2.0 ± 0.1 1.5 ± 0.1 -0 Top tape peeling strength: 10 ~ 55g PAGE 6 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-192 R4 (2) Reel A B D W (unit: mm) A B D W 178 ± 2.0 60 ± 2.0 21 ± 0.8 10 ± 1.0 (3) Leader and End Tape End tape 300 (+20) Leader tape 150 (+20) 350 (+20) (4,000 pieces) Empty Empty Top tape Tape Running Direction (4) Contents on label (1) (2) (3) (4) (5) (6) Type Designation (CR2A10Y) Nominal Capacitance/Nominal Resistance (3 digit/3 digit) Quantity Customer’s code No. Production lot No. Manufacturer’s name Manufacturer’s name PAGE 7 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-192 R4 10. Land Pattern Design F G D B W A C L 4.0 W 2.1 A 1.7 E L B 3.1 (unit: mm) C 0.4 D 0.4 E 0.8 F 5.1 G 3.5 11. Soldering 11-1 Reflow Soldering Reflow soldering should be done at 240°C for less than 20 seconds. 1. The melting time of soldering should be as short as possible. Temperature (°C) 300 200 ~ 240°C 1 ~ 4°C/sec 200 2. After the soldering, allow products to cool naturally. 150°C 100 3. We do not recommend flow soldering to CR Chip Networks, because of concern that a solder bridge occurs due to narrow 0.8 mm pitch. We therefore recommend reflow soldering. cooling naturally 60 ~ 120 sec 30 ~ 60 sec 5 ~ 30 sec 11-2 Cleaning 1. Residual flux after board washing may cause solder migration. Carefully check the status of board washing. 2. Confirm they will not cause problems when they are not washed. 11-3 Others 1. This product has circuits on both sides. Do not use adhesives, because of concern that characteristics will be impaired by adhesives. 2. Do not use the products in dewy atmosphere. PAGE 8 OF 8 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.