D100R Series Tightly Regulated Miniature, 1W SIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: Input Parameter Conditions Min. Typ. Max. 5 VDC Input 4.5 5.0 5.5 12 VDC Input 10.8 12.0 13.2 24 VDC Input 21.6 24.0 26.4 48 VDC Input 44.0 48.0 52.0 • 1W Output Power • Tight Line/Load Regulation Input Voltage Range • Miniature SIP Case • 1,000 VDC Isolation • >2 MHour MTBF • 20 Standard Models • Industry Standard Pin-Out Input Filter Units VDC Internal Capacitor Reverse Polarity Input Current 0.3 A Max. Units ±2.0 % ±0.5 % Output Parameter Conditions Min. Typ. Output Voltage Accuracy Line Regulation For Vin Min to Max Load Regulation (Note 1) ±0.5 % 50 75 mV P - P ±0.01 ±0.02 %/ºC Max. Units Ripple & Noise (20 MHz) (Note 2) Output Power Protection 120 Temperature Coefficient Output Short Circuit % Momentary (0.5 Sec.) General RoHS Compliant Parameter Conditions Isolation Voltage Isolation Resistance Isolation Capacitance Min. 60 Seconds 1,000 500 VDC 1,000 100 kHz, 1V Switching Frequency Typ. VDC MΩ 60 pF 60 kHz Environmental Min. Typ. Max. Operating Temperature Range Parameter Conditions Ambient -40 +25 +85 ºC Operating Temperature Range Case -40 +100 ºC -40 +125 ºC 95 % Storage Temperature Range Cooling Humidity Units Free Air Convection RH, Non-condensing MicroPower Direct Physical 292 Page Street Suite D Stoughton, MA 02072 USA Case Size 0.76 x 0.28 x 0.39 Inches (19.5 x 7.2 x 10.0 mm) Case Material Non-Conductive Black Plastic (UL94-V0) Weight 0.07 Oz (2.1g) Reliability Specifications T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter MTBF Conditions Min. MIL HDBK 217F, 25ºC, Gnd Benign Typ. Max. 2.0 Units MHours Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation Conditions Min. Typ. Max. 5 VDC Input -0.7 9.0 12 VDC Input -0.7 18.0 24 VDC Input -0.7 30.0 48 VDC Input -0.7 55.0 Units VDC 1.5 mm From Case For 10 Sec 260 ºC All Models 450 mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D101R D102R D103R D104R D105R D111R D112R D113R D114R D115R D121R D122R D123R D124R D125R D131R D132R D133R D134R D135R Input Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load 5 4.5 - 5.5 322 28 5 4.5 - 5.5 298 28 5 4.5 - 5.5 298 26 5 4.5 - 5.5 285 26 5 4.5 - 5.5 285 38 12 10.8 - 13.2 136 16 12 10.8 - 13.2 128 16 12 10.8 - 13.2 124 16 12 10.8 - 13.2 119 16 12 10.8 - 13.2 119 16 24 21.6 - 26.4 66 9 24 21.6 - 26.4 61 9 24 21.6 - 26.4 65 9 24 21.6 - 26.4 59 9 24 21.6 - 26.4 59 9 48 44.0 - 52.0 33 7 48 44.0 - 52.0 32 7 48 44.0 - 52.0 32 7 48 44.0 - 52.0 30 7 48 44.0 - 52.0 30 7 Notes: 1. Output load regulation is specified for a load change of 20% to 100%. 2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 10 μF) be placed from the +Vout pin to the -Vout pin. 3. The 5V, 12V and 24V input units do not require external components to operate, but the use of an input capacitor (10 μF) may enhance performance in some applications. An output capacitor (1.0 μF to 10 μF) may be used to reduce ripple. The 48V input models require an input capacitor of 4.7 μF to 47 μF (dependent upon the application). 4. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Voltage (VDC) 3.3 5.0 9.0 12.0 15.0 3.3 5.0 9.0 12.0 15.0 3.3 5.0 9.0 12.0 15.0 3.3 5.0 9.0 12.0 15.0 Output Current (mA, Max) 200.0 200.0 111.0 83.0 66.0 200.0 200.0 111.0 83.0 66.0 200.0 200.0 111.0 83.0 66.0 200.0 200.0 111.0 83.0 66.0 Current (mA, Min) 20.0 20.0 11.0 9.0 7.0 20.0 20.0 11.0 9.0 7.0 20.0 20.0 11.0 9.0 7.0 20.0 20.0 11.0 9.0 7.0 Efficiency (%, Typ) 62 67 67 70 70 61 65 67 70 70 63 68 68 70 70 63 65 67 70 70 Fuse Rating Slow-Blow (mA) 500 500 500 500 500 200 200 200 200 200 100 100 100 100 100 100 100 100 100 100 Mechanical Dimensions Pin Connections Pin Function 1 +Vin 2 -Vin 4 -Vout 6 +Vout Derating g Curve Capacitive Load (μF Max) Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit 220 MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]