AZ762H AZ 16 A SPDT MINIATURE HIGH TEMPERATURE POWER RELAY FEATURES • • • • • • • • High ambient operating temperature (105°C) Dielectric strength 5000 Vrms Low cost Epoxy sealed versions available 16 Amp switching (standard coil only) Class B (130°C) standard Isolation spacing greater than 10 mm UL, CUR file E44211, VDE40006031 CONTACTS GENERAL DATA Arrangement SPDT (1 Form C) SPST (1 Form A) Ratings Resistive load: Max. switched power: 480 W or 4432 VA Max. switched current: 16 A Max. switched voltage: 150* VDC or 440 VAC *Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 16 A 277 VAC general use OperateTime (typical) 7 ms at nominal coil voltage ReleaseTime (typical) 3 ms at nominal coil voltage (with no coil suppression) Dielectric Strength (at sea level for1min.) 5000 Vrms coil to contact 1000 Vrms between open contacts Rated Load UL, CUR 16 A at 277 VAC general use, 100k cycles 105°C (10A sensitive coil) Insulation Resistance 1000 megohms min. at 20°C 500 VDC 50% RH VDE 16 A at 250 VAC resistive, 105°C (10A sensitive coil) 6 A at 400 VAC resistive, 105°C Dropout Greater than 10% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 105°C (221°F) -40°C (-40°F) to 130°C (266°F) Material Silver nickel. Gold plating available Ambient Temperature Operating Storage Resistance < 50 milliohms initially (using 6 V 1 A method) Vibration 0.062" DA at 10–55 Hz Shock 10 g Enclosure P.B.T. polyester Terminals Tinned copper alloy, P. C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) COIL Power At Pickup Voltage (typical) 196 mW Standard 141 mW Sensitive Max. Continuous Dissipation 1.7 W at 20°C (68°F) ambient Temperature Rise 26°C (47°F) at nominal coil voltage Max. Immersion Time 30 seconds 130°C (266°F) Weight 14 grams Max. Temperature NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 11/13/08W AZ AZ762H RELAY ORDERING DATA COIL SPECIFICATIONS - STANDARD RELAYS Nominal Coil VDC 5 Must Operate VDC 3.5 ORDER NUMBER* Max. Continuous VDC 10.2 Coil Resistance ±10% 62 Unsealed AZ762H–1CB–5D 6 4.2 12.3 90 AZ762H–1CB–6D Sealed AZ762H–1CB–5DE AZ762H–1CB–6DE 9 6.3 18.5 202 AZ762H–1CB–5D AZ762H–1CB–19DE 12 8.4 24.7 360 AZ762H–1CB–12D AZ762H–1CB–12DE 18 12.6 37.0 810 AZ762H–1CB–18D AZ762H–1CB–18DE 24 16.8 49.4 1440 AZ762H–1CB–24D AZ762H–1CB–24DE 48 33.6 98.0 5760 AZ762H–1CB–48D AZ762H–1CB–48DE 60 42.0 112.9 7500 AZ762H–1CB–60D AZ762H–1CB–60DE COIL SPECIFICATIONS - SENSITIVE RELAYS ORDER NUMBER* Nominal Coil VDC Must Operate VDC Max. Continuous VDC Coil Resistance ± 10% 5 3.75 10.2 6 4.50 12.3 144 AZ762H–1CB–6DS AZ762H–1CB–6DSE 9 6.75 18.5 324 AZ762H–1CB–9DS AZ762H–1CB–9DSE 100 Unsealed AZ762H–1CB–5DS Sealed AZ762H–1CB–5DSE 12 9.0 24.7 576 AZ762H–1CB–12DS AZ762H–1CB–12DSE 18 13.5 37.0 1296 AZ762H–1CB–18DS AZ762H–1CB–18DSE 24 18.0 49.4 2304 AZ762H–1CB–24DS AZ762H–1CB–24DSE 48 36.0 98.0 9216 AZ762H–1CB–48DS AZ762H–1CB–48DSE 60 45.0 112.9 12857 AZ762H–1CB–60DS AZ762H–1CB–60DSE * For 1 form A contacts substitute “-1AB” for “-1CB.” For gold plated contacts add suffix “A.” 11/13/08W AZ762H HARDWARE ORDERING DATA DESCRIPTION ORDER NUMBER DESCRIPTION ORDER NUMBER Socket ST484–U1 Retainer ST482–3 MECHANICAL DATA .5 2 0 M a x . [1 3 .2 ] 1 .1 6 1 M a x . [2 9 .5 ] PC B O A R D LA YO U T V IE W E D T O W A R D S T E R M IN A L S .1 9 7 [5 .0 ] .597 [15.16] .1 9 7 [5 .0 ] .619 Max. [15.7] .0 9 8 [2 .5 ] .2 9 5 [7 .5 ] .2 9 5 [7 .5 ] .1 5 4 [3 .9 ] 6 X .0 2 0 [0 .5 ] .0 9 8 [2 .5 ] 2 Xø.0 3 2 [ø0 .8 ] 6 Xø.0 5 0 [ø1 .3 ] 2 Xø.0 2 4 [ø0 .6 ] .2 9 5 [7 .5 ] 6 X .0 3 5 [0 .9 ] ST484-U1 .1 9 7 [5 .0 ] .597 [15.16] .1 9 7 [5 .0 ] HARDWARE .0 9 8 [2 .5 ] .5 0 0 (1 2 .7 ) 1 .2 8 (3 2 .5 ) 1 .2 2 (3 0 .9 ) WIRING DIAGRAMS .4 1 4 (1 0 .5 ) VIEWED TOWARDS TERMINALS 5 * 8* 4 7 3 * 6* 2 .1 2 5 D IA (0 .5 ) .3 6 6 (9 .3 ) R E AT IN IN G C L IP .2 9 5 (7 .5 ) 1 * Terminals 3 & 6 not used on form A .3 5 4 (9 .0 ) .1 7 7 (4 .5 ) M AX .5 9 0 (1 5 ) .1 1 8 (3 .0 ) .1 9 7 (5 .0 ) .1 9 7 (5 .0 ) .0 5 9 D IA (1 .5 ) 1 .3 8 5 [3 5 .1 9 ] .8 9 5 [2 2 .7 3 ] .6 6 1 [1 6 .7 9 ] ST482-3 Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 11/13/08W