AZ AZ832P POLARIZED DIP RELAY BISTABLE (LATCHING) FEATURES • • • • • • • • • • High sensitivity, 42 mW pickup Low profile DIP package Meets FCC Part 68.302 1500 V lightning surge Meets FCC Part 68.304 1000 V dielectric Single and dual coil versions DC coils to 24 VDC High switching capacity, 60 W, 250 VA Fits standard 16 pin IC socket Epoxy sealed for automatic wave soldering and cleaning UL, CUR file E43203 CONTACTS GENERAL DATA Arrangement DPDT (2 Form C) Bifurcated crossbar contacts Ratings Resistive load: Max. switched power: 60 W or 250 VA Max. switched current: 2 A Max. switched voltage: 250 VDC or 250 VAC Rated Load UL 2 A at 30 VDC resistive 2 A at 125 VAC resistive Material Gold plated silver against gold plated silver Resistance < 50 milliohms initially COIL Power Life Expectancy Mechanical Electrical Minimum operations 2 x 107 1 x 105 at 2 A, 30 VDC or 1 A, 125 VAC 2 x 106 at 1 A, 30 VDC or .5 A, 125 VAC Set Time (typical) 3 ms at nominal coil voltage Reset Time (typical) 3 ms at nominal coil voltage Bounce (typical) 3 ms Dielectric Strength (at sea level) 1500 Vrms contact to coil 1000 Vrms between contact sets 1000 Vrms across contacts Meets FCC Part 68.302 lightning surge Meets FCC Part 68.304 V dielectric Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 115°C (239°F) At Pickup Voltage (typical) Standard coil: 56 mW Sensitive coil: 42 mW Vibration 50 g at 10–500 Hz Max. Continuous Dissipation 0.9 W at 20°C (68°F) Shock 50 g Max. 115°C (239°F) Enclosure P.B.T. polyester Terminals Tinned copper alloy, P.C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 5 grams Temperature NOTES 1. 2. 3. 4. All values at 20°C (68°F). Relay may pull in with less than “Must Operate” value. Relay has fixed coil polarity. For complete isolation between the relay’s magnetic fields, it is recommended that a .197" (5.0 mm) space be provided between adjacent relays. 5. Relay adjustment may be affected if undue pressure is exerted on relay case. 6. Specifications subject to change without notice. 8/3/07 W AZ832P RELAY ORDERING DATA STANDARD SINGLE COIL COIL SPECIFICATIONS Nominal Max. Coil Continuous VDC VDC 3 9.0 Coil Resistance ± 10% 90 Set Reset VDC 2.25 ORDER NUMBER AZ832P1-2C–3DE 5 15.0 250 3.75 AZ832P1–2C–5DE 12 36.0 1,440 9.0 AZ832P1–2C–12DE 24 60.0 4,000 18.0 AZ832P1–2C–24DE 2.25 7.8 3 10.4 SENSITIVE SINGLE COIL 67.5 1.69 AZ832P1–2C–2.25DSE 120 2.25 AZ832P1–2C–3DSE 5 17.2 330 3.75 AZ832P1–2C–5DSE 12 41.6 1,920 9.0 AZ832P1–2C–12DSE 24 83.1 7,680 18.0 AZ832P1–2C–24DSE STANDARD DUAL COIL COIL SPECIFICATIONS Nominal Max. Coil Continuous VDC VDC 3 6.4 Coil Resistance ± 10% 45 Set Reset VDC 2.25 ORDER NUMBER AZ832P2–2C–3DE 5 10.6 125 3.75 AZ832P2–2C–5DE 6 12.7 180 4.5 AZ832P2-2C–6DE 12 25.5 720 9.0 AZ832P2–2C–12DE 24 42.8 2,040 18.0 AZ832P2–2C–24DE 3 7.3 SENSITIVE DUAL COIL 60 2.25 AZ832P2–2C–3DSE 5 12.3 167 3.75 AZ832P2–2C–5DSE 6 14.7 240 4.5 AZ832P2-2C–6DSE 12 29.4 960 9.0 AZ832P2–2C–12DSE 24 58.8 3,840 18.0 AZ832P2–2C–24DSE MECHANICAL DATA PC BOARD LAYOUT TWO COIL VERSION .394 MAX [10.00] .795 MAX [20.20] .048 [1.21] .047 [1.19] .100 [2.54] .419 MAX [10.65] .026 [0.66] 1 2 4 6 8 13 11 9 .300 [7.62] 16 15 .118 [3.00] .048 [1.21] 6 x 020 ± .005 [0.50±0.12] 6 x .010 ± 005 [0.25± 0.12] 4 X .016 [0.40] 3 x .200 [5.08] 10 x ø.039 [ø1.0] VIEWED TOWARD TERMINALS WIRING DIAGRAM TWO COIL LATCHING 1 2 + WIRING DIAGRAM SINGLE COIL LATCHING 4 6 8 + - - 1615 SET 13 11 RESET NOTE: DIAGRAMS SHOW THE “RESET” POSITION BEFORE ENERGIZED WITH POLARITY AS SHOWN 9 (WATCH FOR POLARITY) VIEWED TOWARD TERMINALS + 1 4 6 8 16 13 11 9 - (WATCH FOR POLARITY) VIEWED TOWARD TERMINALS Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 8/3/07 W