White Electronic Designs Display Systems Division ENH050Q1-320/450/600 ENH050Q1-320/450/600 Color TFT-LCD Module Features GENERAL DESCRIPTION Panelview provides optically enhanced solutions to the standard Sharp LQ5AW136 color active matrix LCD module. The first enhancement is an index matching (IM) film lamination to the front surface of the display polarizer. The IM film is available in two surface treatments - IM/Clear and IM/110 (a 10% diffusion).The second enhancement is the incorporation of a reflective polarizer (RP) to improve brightness by up to 40%. The third enhancement is the addition of prism films (RPp) further increasing the brightness of the display. The module accepts full color video signals conforming to the NTSC(M) and PAL(G-B) system standards. It can withstand an intense environment, the online dimension is suitable for an automotive display, compact size, compatible with 2DIN size. Panelview assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. Panelview does assume the responsibility for the warranty of the enhanced product. FEATURES Slim, lightweight and compact 1. Active area/Outline area=70% 2. Thickness: 16.5mm 3. Mass: 185g (Max) Built-in video interface circuit and control circuit responsive to two sets of standard RGB analog video signals. Reduced refleciton as a resuld of low reflectance Black-Matrix and Index Matching (IM) film lamination. IM is available in two surface treatments, IM/Clear (glossy) and IM/110 (10% diffusion). It is possible to use both the simultaneous and the independent time sampling. An external clock mode is available. Optical viewing angle: wide view angle (6 o'clock direction.) (Customer can use this module as a 12 o'clock viewing direction type by using a display rotating function to rotate right/left and up/down scanning direction electrically.) This module includes a high luminance edge light that is excellent at low temperature. It is possible to use the dimming frequency (PWM) for backlight. Dual mode type. [NTSC(M) and PAL(B-G) standards] MBK-PAL enables the 234-scanning lines panel to display a picture with virtually 273-scanning lines. CONSTRUCTION AND OUTLINE Outline dimensions of TFT-LCD module: See Fig. 3 TFT-active matrix-LCD drive system with high contrast. 74,800 pixels (RBG Stripe configurations and full color) 5" diagonal size. The module consists of a TFT-LCD panel, driver IC's control PWB mounted with electronic circuits, edge light, frame, front and rear shielding cases. (Backlight driving DC/AC inverter is not built in the module.) MECHANICAL SPECIFICATIONS Parameter Display Format Active Area Screen Size (Diagonal) Dot Pitch Dot Configuration Outline Dimension (1) Mass Specifications 74,800 960 (W) x RGB x 234 (H) 102.2 (W) x 74.8 (H) 13 (5") 0.1065 (W) x 0.3195 (H) RGB Stripe configuration 126.8 (W) x 89.6 (H) x 16.5 (D) 185 (Max) Units pixels dots mm cm mm mm g Note: This measurement is typical, and see Fig. 3 for details. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 1 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 INPUT TERMINALS AND THEIR DESCRIPTIONS TTL-LCD Panel Driving Section (Hi means digital input voltage, Lo means GND.) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Symbol HSY VSY PWM NTP HRV VRV VSW SAM VCDC VSH VBS BRT VR1 I/O I, O I, O O I I I I I I I I I I 14 VG1 I Color video signal (Green) 1 15 VB1 I Color video signal (Blue) 1 16 17 VSL VR2 I I Negative power supply voltage Color video signal (Red) 2 18 VG2 I Color video signal (Green) 2 19 VB2 I 20 21 22 GND CKC CK I I I, O Description Input/Output horizontal sync. signal (low active) Input/Output vertical sync. signal (low active) Terminal for output PWM of dimming back light Terminal for display mode change of NTSC and PAL Turning the direction of horizontal scanning Turning the direction of vertical scanning Selection signal of two sets of video signals Terminal for sampling mode change DC bias voltage adjusting terminal of common electrode driving signal Positive power supply voltage Composite video signal of sync. seperator Brightness adjusting terminal Color video signal (Red) 1 Remarks (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) Positive (On when VSW=Hi.) Positive (On when VSW=Lo.) Color video signal (Blue) 2 Ground Change the input/output direction of CK, HSY and VSY. Input/Output clock signal (12) (13) Note: 1. If CKC='Hi', this terminal outputs horizontal sync. signal in phase with VBS. If CKC='Lo', this terminal will be external horizontal sync. input terminal. 2. If CKC='Hi', this terminal outputs vertical sync. signal in phase with VBS. If CKC='Lo', this terminal will be external vertical sync. input terminal. 3. PWM signal is used for the PWM dimming frequency and it is easy to get PWM signal dimming by combining both HSY and PWM signals. But use this PWM signal in case of input standard NTSC or PAL signal. 4. This terminal is to switch the display mode, and it is NTSC mode when NTP is 'High' and is PAL mode when NTP is 'Low'. 5. When this terminal is 'High', it will be normal and when it is 'Low', it will display reversely on the horizontal direction. 6. When this terminal is 'High', it will be normal and when it is 'Low', it will display reversely on the vertical direction. 7. This terminal is to switch input for groups of RGB color video signals, and Input 1 (No. 13 to 15) is selected when VSW is 'High' and Input 2 (No. 17 to 19) is selected when VSW is 'Low'. 8. This terminal switches to sampling mode. It is the independent data-sampling timing at RGB dot when SAM is 'High' and it is the simultaneous data-sampling timing at RGB dots when SAM is 'Low'. 9. This terminal is applicable to the DC bias voltage adjusting terminal of the common electrode driving signal. If power supply voltage is typical, it is not necessary to re-adjust it. So, Use it in the open condition. However, in the case that the power supply voltage is changed, or power supply voltage is reduced, adjust it externally to get the best contrast with a resistor that is added to this terminal, or semi-fixed resistor, VCDC in module. A recommended circuit is shown in Fig. 5. 10. The sync. signal which will be input, is negative polarity and is applicable to standard composite sync. signal, negative one in the same pulse level. 11. DC voltage supplied to this terminal, makes the brightness of the screen adjustable, which is the black level of the video signal. Although this is adjusted in the time of delivery to get the best display in the condition of the open terminal, it is also able to be re-adjusted externally with a resistor that can be added to this terminal, or a semi-fixed resistor, BRT, in module. A recommended circuit is shown in Fig. 5. 12. CKC-'Hi', CK.HSY.VSY terminals are output mode. CKC='Lo': CK. HSY. VSY terminals are input mode. 13. If CKC='Hi', this terminal outputs the clock for sure drivers. If CKC='Lo', this terminal will be the external clock input terminal. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 2 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 FUNCTIONAL MACHINE AND INPUT/OUTPUT MODE CKC="Hi" Terminal HSY VSY CK SAM="Hi" Output Output Output "Dot Clock" CKC="Lo" SAM="Lo" Output Output Output "Pixel Clock" SAM="Hi" Input Input Input "Dot Clock" SAM="Lo" Input Input Input "Pixel Clock" BACKLIGHT DRIVING SECTION Terminal CN1 No. 1 2 3 Symbol VL1 NC VL2 I/O I I Function Input terminal (Hi voltage side) [14] Non connection Input terminal (low voltage side) Note: 14. Low Voltage side of DC/AC inverter for backlight driving connects with Ground of inverter circuit. ABSOLUTE MAXIMUM RATINGS GND = OV, tA = 25°C Parameter Positive power supply voltage Negative power supply voltage Analog input signals (1) Digital input/output signals (2) DC bias voltage of common electrode driving signal Brightness adjusting terminal Storage temperature (3) Operating temperature (3, 4) surface of panel environment Symbol VSH VSL VI VI VCDC VBRT tSTG Top1 Top2 MIN -0.3 -6.0 -0.3 VSL 0 -30 -30 -30 MAX +9.0 +0.3 2.0 +5.4 VSH +5.1 85 85 60 Unit V V Vp-p V V V °C °C °C Notes: 1. VBS, VR1, VG2, VB1, VR2, VG2, VB2 terminals (Video signal) 2. NTP, HRV, VRV, SAM, VSW, HSY, VSY, CKC, CK terminals 3. The temperature of all parts in module should not exceed this rating. Maximum wet-bulb temperature should be less than 58°C. No dew condensation. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 3 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 ELECTRICAL CHARACTERISTICS RECOMMENDED OPERATING CONDITIONS TFT-LCD PANEL DRIVING SECTION GND=0V, tA=25°C Parameter Positive power supply voltage Negative power supply voltage Analog input voltage Amplitude Digital Input voltage Digital output voltage Output clock Input horizontal sync. component DC component High level Low level Histeresis High level Low level Duty cycle Drive capability freq. pulse width Input vertical sync. component Input clock Input HSY (Horizontal sync.) Input VSY (Vertical sync.) Data set up time Data hold time Data set up time Data hold time NTSC PAL NTSC PAL rise time fall time freq. NTSC PAL pulse NTSC width PAL rise time fall time frequency High width Low width rise time fall time frequency pulse width rise time fall time frequency pulse width rise time fall time Symbol VSH MIN +7.8 TYP +8.0 MAX +8.2 Unit V VSL VBS VI VIDC VIH VIL VH VOH VOL Duty IOH IOL fH (N) fH (P) tHI (N) tHI (P) trHI1 tfHI1 fV (N) fV (P) tVI (N) tVI (P) trVI1 tfVI1 fCLI fCLI tWH tWL trCLI tfCLI fHI fHI -5.2 0.7 -1.0 -3.7 0 0.4 +4.0 0 45/55 -0.28 15.13 15.03 4.2 4.2 fH/284 fH/344 18.2 6.0 20.0 20.0 fCLI/1230 fCLI/465 -5.0 1.0 0.7 0 50/50 15.73 15.63 4.7 4.7 fH/262 fH/312 3H 2.5H 18.9 6.8 fCLI/1200 fCLI/435 -4.8 2.0 -1.0 +5.1 +1.0 +5.5 +1.0 55/45 0.25 16.33 16.23 5.2 5.2 0.5 0.5 fH/258 fH/304 0.5 0.5 19.6 7.6 5.0 5.0 fCLI/1170 fCLI/405 V Vp-p Vp-p V V V V V V mA mA kHz kHz µs µs µs µs Hz Hz µs µs µs µs MHz MHz ns ns ns ns Hz Hz tHI trHI1 tfHI1 fVI tVI (P) trVI1 tfVI2 tSU1 tHO1 tSU2 tHO2 1.0 50 1H 25 25 1.0 1.0 4.7 fHI/262 3H - 8.4 0.05 0.05 fHI/258 5H 0.5 0.5 - µs µs µs Hz µs µs µs ns ns µs µs Remarks (1) Input resistor is over 10kΩ. (2) (3) Input resistor is over 10kΩ. (4) Load resister is over 60kΩ. (5) CKC=High (6) (7) VOH=2.6V VOL=2.3V CKC=High (8) for VBS terminal CKC=High, H=1/fH (9) for VBS terminal SAM=High SAM=Low CKC=Low (10) for CK terminal SAM=High SAM=Low CKC=Low (11) for CK terminal (12) CKC=Low for VSY terminal (13) CKC=Low (14) White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 4 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 TFT-LCD PANEL DRIVING SECTION Parameter DC bias voltage for common electrode driving signal Terminal voltage applicable to brightness Symbol VCDC VBRT MIN 0 +2.0 Notes: 1. Power supply voltage should not be changed after adjusting VCDC. 2. VR1, VG1, VB1, VR2, VG2, VB2 terminal (Video signal) 3. VBS, VR1, VG1, VB1, VR2, VG2, VB2 terminals 4. HSY, VSY, NTP, VSW, HRV, VRV, SAM CKC, CK terminal 5. HSY, VSY, CK terminals (output mode) 6. CK terminals (output mode) 7. Duty cycle is defined as follows. TYP +2.0 +2.3 8. 9. 10. 11. 12. 13. 14. 15. Duty=tOL/tOH tOH tOL MAX +3.0 +2.4 Unit V V Remark DC component (15) VBS (horizontal sync. component) VBS (vertical sync. component) CK (input mode) HSY (input mode) VSY (input mode) In case of cKC='Lo', it shows the phase different from HSY to CK. In that case, HSY will be taken at the rise timing of CK. In case of CKC='Lo'. it shows the phase difference from VSY to HSY. In that case, VSY will be taken at the rise timing of HSY. Adjsuting the optimal voltage on every module at the typical value of power supply voltage to get the maximum value of contrast. However, in the case that the power supply voltage is changed, for example the level of power supply voltage is reduced, adjust it externally to get the best contrast with a resistor you add to this terminal, or semifixed resistor, VCDC, in module. A recommended circuit is shown in Fig. 5. BACKLIGHT DRIVING SECTION Parameter Lamp Voltage Lamp current Lamp frequency Kickoff voltage Symbol VL7 IL fL VS MIN 550 3.0 20 - TYP 610 6.5 - MAX 670 7.0 70 1450 1500 Unit Vrms mArms KHz Vrms Vrms Remark IL=6.5mArms normal operation tA = +25°C tA = -30°C POWER COMSUMPTION tA = 25°C Parameter Positive supply current Negative supply current Total Lamp power consumption 16. 17. Symbol ISH ISL WS WL Conditions VSH = +8.0V VSL = -5.0V normal driving MIN - TYP 140 55 1.4 4.0 MAX 170 70 1.7 - Unit mA mA W W Remark (16) (17) Excluding backlight section Reference data by calculation (IL x VL x 1: number of lump) Circuit Diagram Input/Output Signal Waveforms (Fig. 6) The circuit block diagram of TFT-LCD module is shown in Fig. 4. Caution: For the VBS signal, input standard composite video (or sync.) signal applicable to the operating mode which have NTSC (M) or PAL (B-G) and is selected by the NTP signal. BRT, VCDC, external adjusting recommended circuit is shown in Fig. 5. Caution: Turn the power supply on or off (VSH and VSL) at the same time. Be careful to supply all power voltage before inputting signals. Dimming Backlight by PWM Timing Chart If using PWM mode, refer to the timing chart shown in Fig. 7. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 5 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 INPUT/OUTPUT SIGNAL TIMING CHART (FIG. 6) (CKC=HIGH, NTSC: fH=15.7kHz, fV=60Hz/PAL: fH=15.6kHZ, fV=50Hz) Parameter Horizontal sync. output pulse [HSY] Symbol tHS2 tPD trHO tfHO tVS tvHO trVO tfVO tpV1 tpV2 fCLO Min. 3.2 0.4 - Typ. 3.9 1.1 4H 11.0 1H 0.5H fH x 1201 2 Max. 4.6 1.8 0.5 0.5 28.0 2.0 2.0 - Unit µs µs µs µs µs µs µs µs µs µs MHz PAL MODE fCLO - fH x 1209 2 - MHz (22) NTSC MODE fCLO - fH x 1201 6 - MHz SAMC="Lo" PAL MODE fCLO - fH x 1209 6 - MHz (23) pulse width phase difference rise time fall time pulse width phase difference rise time fall time odd field even field NTSC MODE Vertical sync. output pulse [VSY] Vertical phase difference Clock output frequency [CK] Reward f=fH (18) (19) CL=10pF 1H=1/fH (20) CL=10pF 1H=1/fH (21) SAMC="Hi" (Supply voltage conditions: VSH = +8.0V, VSL = 5.0V) Notes: 18. Adjusted by variable resister (H-POS) in a module. 19. Variable by variable resister (H-POS) in a module. adjustment : tpd = 1, 1 ± 0.7 µs 20. Synchronized with HSY, based on falling timing of HSY. 21. VSY signal delays 22. Independent sampling mode. 23. Simultaneous sampling mode. Display Time Range However, the video signals of NTSC (M) mode (NTP=High, CKC=High) Displaying the following range within video signals. • Horizontally: 12.2 ~ 63 µs 12.3 ~ 62.9 µs • Vertically: 20 ~ 253 H (14n+17)H, (14n+23) H/Odd field (n=1, 2..., 20) from the falling edge of HSY. (SAM=High) are not displayed on the module. from the falling edge of HSY. (SAM-Low) • Horizontally: 205 ~ 1164 ck from the falling edge of VSY. PAL(B-G) Mode (NTP-Low, CKC=High) Displaying the following range within video signals. • Horizontally: 13.0 ~ 63.8 µs from the falling edge of HSY. (SAM=High) 13.1 ~ 63.7 µs from the falling edge of HSY. (SAM-Low) • Vertically: 26 ~ 298 H (14n+12)H, (14n+20) H/Even field. External Clock Mode (NTP=High, CKC='Lo') 84 ~ 403 ck from the falling edge of HSY. (SAM=High) from the falling edge of HSY. (SAM-Low) (ck means input external clock.) • Vertically: 20 ~ 253 H from the falling edge from the falling edge of VSY. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 6 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 OPTICAL CHARACTERISTICS tA=25°C Parameter Viewing Angle Range Contrast Ratio Response Time Rise Fall Luminance White Chromaticity Lamp Life Time +25’C -30’C Symbol ∆θ11 ∆θ12 ∆θ2 CRmax tr td Y x y - Condition CR>5 Optimal θ = 0° IL=6.5mArms IL=6.5mtVms IL=6.5mArms Continuation Intermission Min 60 35 60 60 240 0.263 0.279 10,000 2,000 Typ 65 40 65 30 50 320 0.313 0.329 - Max 60 100 0.363 0.379 - Unit ° (degree) ° (degree) ° (degree) ms ms cd/m2 hour time Remarks (1,2) (2,3) (2,4) (5) (6) (7) DC/AC inverter for external connection shown in following. Harison Electric Co., Ltd, HIU-288. Notes: 1. Viewing angle range is defined as follows. Fig. 1: Definition of Viewing Angle Normal line ∆θ2 ∆θ2 ∆ θ 12 ∆ θ 11 6 o'clock direction 2. 3. Applied voltage conditions: a. VCDC is adjusted so as to attain maximum contrast ratio. b. Brightness adjusting voltage (BRT) is open. c. Input video signal of standard black level and 100% white level. Contrast ratio is defined as follows: Contrast ratio (CR)= Photodetector output with LCD being "white" Photodetector output with LCD being "black" White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 7 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division 4. ENH050Q1-320/450/600 Response time is obtained by measuring the transition time of photodetector output, when input signals are applied so as to make the area "black" from "white" and "white" from "black". black Photodetector output (Relative Value) white white 100% 90% 10% 0% td tr time 5. 6. 7. Measured on th ecenter area of the panel at a viewing cone 1° by TOPCON luminance meter BM-7. (After 30 minutes operation) DC/AC inverter driving frequency : 49kHz Lamp life time is defined as the time when either "a" or "b" occurs in the continuous operation under the condition of lamp current IL=3~7. 0mArms and PWM dimming 100%~5%. (tA=25°C) a. Brightness becomes 50% of the original value. b. Kick off voltage at tA=30°C exceeds maximum value, 1500Vrms. The intermittent cycle is defined as a time when brightness becomes 50% of the original value under the condition of following cycle. Ambient temperature: -30°C HIGH (6.5mArms) OFF 5 min. 5 min. 5 min. 5 min. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 8 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 MECHANICAL CHARACTERISTICS By applying pressure on the active area it is possible to cause damage to the display. Input/Output Connectors Performance Input/Output connectors for the operation of LCD module (FPC connector 22 pin) - Applicable FPC Shown in Fig. 3. - Terminal holding force: more than 0.9N/pin. (Each terminal is pulled out at a rate of 25 ±3mm/min.) 23.0 1.0 21 +0.05 -0.05 1.0 +0.02 -0.02 0.7 +0.07 -0.05 +0.15 -0.15 (R0.5) 5 MIN 6 MIN 0.3 +0.1 -0.1 4 1 3 2 No. Name 1 Base material 2 Copper foil 3 Cover lay 4 Reinforcing plate Materials Polyimide or equivalent material (25µm thick) Copper foil (35µm thick) Solder plated in 2 to 12µm Polyimide or equivalent material Polyester polyimide or equivalent material (188µm thick) (Fig. 3) FPC applied to input/output connector (1.0mm pitch) I/O CONNECTOR OF BACKLIGHT DRIVING CIRCUIT Symbol CN1 Used Connector BHR=02(8.0)VS-1N Corresponding connector SM02(8.0)B-BHS-TB (wire to board) SM02(8.0)B-BHS-1N (wire to board) BHMR-03V(wire to wire) Manufacturer JST JST JST White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 9 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division DISPLAY QUALITY The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standards. ENH050Q1-320/450/600 a) Floor: Conductive treatment of 1MΩ or more on the title (conductive amt of conductive paint on the tile) HANDLING INSTRUCTIONS b) Clean room free from dust and with an adhansive mat on the doorway Mounting the module c) Advisable humidity:50%~70% The TFT-LCD module is designed to be mounted on equipment using the mounting tabs in the four corners of the module at the rear side. When mounting the module, the M2.6 tapping screw (fastening torque is 0.3 through 0.5N•m) is recommended. Make certain to fix the module on the same plane. Avoid warping or twisting the module. PRECAUTIONS IN MOUNTING Polarizer which is made of soft material and susceptible to flaws must handled carefully. A protective film (Laminator) is applied on the surface to protect it against scratches and dirt. It is recommended to peel off the laminator immediately before use, taking care of static electricity. Precautions in peeling off the laminator A) Working environment When the laminator is peeled off, static electricity may cause dust to stick to the polarizer surface. To avoid this, the following working environment is desired. Advisable temperature:15°C~27°C d) Workers shall wear conductive shoes, conductive work clothes, conductive gloves and an earth band. If the TFT-LCD module metal parts (shielding lid and rear case) become soiled, wipe them with a soft dry cloth. Wipe off water spots of finger grease immediately. Prolonged contact with water may cause discoloration or spots. The TFT-LCD module uses glass which breaks or cracks easily if dropped or bumped on a hard surface. Handle with care. Since CMOS LSI is used in this module, take care of static electricity and ground one's body when handling. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 10 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division Precautions in Adjusting Module Variable resistor on the rear face of the module has been adjusted optimally before shipmetn. Therefore, do not change any adjusted values. If adjusted values are changed, the specifications described here may not be satisfied. Caution of Product Design 1. The LCD module shall be protected against water by the waterproof cover. Others 1. Do not expose the module to direct sunlight or intensive ultraviolet rays for many hours; liquid crystal is deteriorated by ultraviolet rays. 2. Store the module at a temperature near room temperature. When stored at lower than the rated storage temperature, liquid crystal solidifies, causing the panel to be damaged. When stored at higher than the rated storage temperature, liquid crystal turns into isotropic liquid and may not recover. ENH050Q1-320/450/600 SHIPPING REQUIREMENTS Carton storage conditions: Number of layers of carton in stack: 10 layers max Environmental conditions: Temperature: 0~40°C Humidity: 60%RH or less (at 40°C) No dew condensation at low temperature and high humidity, Atmosphere Harmful gases such as acid and alkali which corrode electronic components and wires must not be present. Storage period Approximately 3 months Opening of package To prevent TFT-LCD module from being damaged by static electricity, adjust the room humidity to 50%RH of higher and make certain one is grounded before opening the package. 3. If LCD panel breaks, the liquid crystal could possibly escape from the panel. Since the liquid crystal is injurious, avoid contact with the eyes or mouth. Wash with soap immediately if contact with the liquid crystal occurs. RELIABILITY TEST 4. Observe all other precautionary requirements in handling general electronic components. and should be strictly avoided. Image retention may occur when a fixed pattern is displayed for a long time. Reliability test conditions for the TFT-LCD module are shown on page 12. White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 11 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 RELIABILITY TEST ITEMS FOR TFT-LCD MODULE No. 1 2 3 4 5 6 7 8 Test items High temperature storage test Low temperature storage test High temperature and high humidity operating test High temperature operating test Low temperature operating test Electrostatic discharge test Shock test Vibration test 9 Heat shock test Test conditions tP=-85°C tP=-30°C tP=-60°C, 90~95%RH 240h 240h 240h tP=-85°C tP=-30°C =200V • 200pF(OΩ) 980m/s2 6ms. Frequency Range: 8~33.3Hz Stroke: 1.3mm Sweep: 33.3Hz~400Hz Acceletation: 28.4m/s2 Frequency: 15 minutes 2 hours for each direction of X, Z (1) 4 hours for direction of Y (8 hours in total) -30°C~-85°C/200 cycles (0.5h) (0.5h) 240h 240h Once for each terminal ±X, ±Y, ±Z 3 times for each direction (JIS C0041. A-7 Condition C) tP=Panel temperature Evaluation Result Criteria: Note 1: Direction of X, Y, Z is defined as follows: 1 2 o' clock direction Z X 6 Y o' clock direction White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 12 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 OUTLINE DIMENSIONS 126.8 ± 0.3 13 +0.3 -0.2 13 +0.3 -0.2 Screen center 42.4 RG B RG 89.9 MAX 79.8 (Case open area) 89.6 ± 0.3 Screen size (102.24 x 74.763) Direction of best viewing angle (6 o'clock) 107.4 (Case open area) 960H x 234V dots 13 +0.3 -0.2 0.2 +0.1 -0.1 +0.3 5 5 9.5 16.5 -0.2 3 3 datum line 11 89.2 2.2 31.2 2.2 datum line 03A Rear View White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 13 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 Backlight TFT-LCD panel Gate driver Control circuit Backlight driving signal Video interface circuit Amplifying polarity inversion Sync. separator Fig. 4 Circuit block diagram of TFT-LCD module LCD driving signal Common driving signal (COM) Gate driver driving signal Source driver driving signal FRP HSY VSW Source driver Gate driver power supply circuit Regulator SYN Gate driver power supply +5.3V VSH VSL VHL VCDC BRT Power supply for backlignt RGB video signal 2 RGB video signal 1 VBS VSW NTP HSY VSY CK CKC GND Power supply VSH, VSL (Caution) * Not included in the module Backlight * driving circuit VSH White Electronic Designs Display Systems Division ENH050Q1-320/450/600 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 14 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 clock vertical sync. horizontal sync. 0 0 5V 0 5V 0 5V A G D B (INPUT) 0.7VPP (Note) input impedance of A, B, D: >10kΩ input impedance of C: >50kΩ G: F: E: D: C: 5V +8V 0.7VPP B: -5V C under HV 1VPP E F GND A: (Gray scale) I/O Signals +5V -5V +8V HSY VSY PWM N/P HRV VRV VSW SAM VCDC VSH VBS BRT VRI VGI VBI VSL VR2 VG2 VB2 GND CLKC CLK 1kΩ I 1kΩ 8.2kΩ 560Ω 560Ω 560Ω 560Ω 560Ω 560Ω 560Ω C-MOS LSI 0.01xF 0.01xF 0.01xF 0.01xF 0.01xF 0.01xF +5.3V IC C-MOS LSI C-MOS LSI C-MOS LSI IC 10kΩ 2kΩ 15kΩ 8.2kΩ 50kΩ Driver ICs COM -5V +8V Driver ICs IC 47kΩ +5.3V TFT-LCD Module Regulator +5.3V 10kΩ Fig. 5 Recommended Circuit SW SW I/O Connector White Electronic Designs Display Systems Division ENH050Q1-320/450/600 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 15 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division trHO t f HO Fig. 6-A Input/Output signal waveforms (CKC= "High") tVHO tpv2 19H (NTSC) 25H (PAL) Vertical display period: HSY HSY VIDEO (R,G,B) VSY VBS 0.7 Vp-p tpv1 3H (NTSC) 2.5H (PAL) tvs VSY detailed tVHO trVO 16.7ms (NTSC) 20ms (PAL) 234H (NTSC) 273H (PAL) 1.0 Vp-p odd field even field tfVO ENH050Q1-320/450/600 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 16 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 Video signal VR1~VB1 or VR2~VB2 HSY VBS 50% 50% 12.3 µs (NTSC, SAM Low) 13.0 µs (NTSC, SAM High) 13.4 µs (NTSC, SAM Low) 12.2 µs (NTSC, SAM High) tHS2 tpd tHS1 tfH0 90% 10% Fig. 6-B Input/Output signal waveforms (CKC="High") Horizontally display area 50.6µs (SAM "Low") Horizontally display area 50.8µs (SAM "High") 1H=63.5µs (NTSC) 1H=64.0µs (PAL) trH0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 17 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 HSY INDEPENDENT SAMPLING MODE (DOT CLOCK) SIMULTANEOUS SAMPLING MODE (PIXEL CLOCK) SYSTEM CLOCK PAL MODE HSY INDEPENDENT SAMPLING MODE (DOT CLOCK) SIMULTANEOUS SAMPLING MODE (PIXEL CLOCK) SYSTEM CLOCK NTSC MODE 1185 1185 1190 1195 1195 1200 RESET 1200 0 1205 Fig. 6-C Input/Output signal waveforms (CLKC="High") 1190 RESET 5 0 52.9 ns 10 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 18 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division HSY tH01 1H trVO tfCLI HSY VSY HSY HSY VSY tHI trCLI CK Fig. 6-D Input/Output signal waveforms (external clock mode NTP="High", CKC="Low") tH02 tSU1 tWL tfH12 tWH trH12 tfVO tSU2 ENH050Q1-320/450/600 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 19 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division Fig. 7 PWM signal waveform for dimming backlight Period of DC/AC inverter oscillation nH 89H (PAL) PWM 1/2H 1/2H HSY VSY 1H magnify TIME range 89H (PAL) PWM (NTSC) PWM VSY 105H nH 105H (NTSC) 525H (NTSC) 625H (PAL) Period of stop DC/AC inverter oscillation ENH050Q1-320/450/600 White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 20 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0 White Electronic Designs Display Systems Division ENH050Q1-320/450/600 ADJUSTING METHOD OF OPTIMUM COMMON ELECTRODE DC BIAS VOLTAGE Normal line Photodetector (including luminosity factor) To obtain optimum DC bias voltage of common electrode driving signal (VCDC). Photo-electric devices are very effective, and the accuracy is within 0.1V. (In visual examination method, the accuracy is about 0.5V because of the difference amoung individuals.) To gain optimum common electrode DC bias voltage, there is the following method which uses the photoelectric device. θ (Measurement of flicker) Polarizing filter Frame DC bias voltage is adjusted so as to minimize NTSC: 60Hz (30Hz) PAL: 50Hz (25Hz) flicker. Photo-electric device Output voltage Backlight (Plane source) LCD panel VCDC LCD Oscilloscope (X-Y recorder) Brightness: Less than 5000cd/m2 Wave length: To be cut less than 400nm Fig. 9 Optical characteristics Fig. A Measurement system Photo-electric output voltage is measured by an oscilloscope at a system shown in Fig. A. DC bias voltage must be adjusted so as to minimize the NTSC:60Hz(30Hz) PAL:50Hz(25Hz) flicker with DC bias voltage changing slowly. (Fig. B) DC bias: Optimum DC bias: Optimum + 1V Fig. B Waveforms of flicker White Electronic Designs Corp. reserves the right to change products or specifications without notice. Original specifications created by Sharp. August 2003 21 Display Systems Division • Hillsboro, OR • (503) 690-2460 • www.wedc.com Rev. 0