INTEGRATED CIRCUITS CBT3251 1-of-8 FET multiplexer/demultiplexer Preliminary data 2002 Sep 09 Philips Semiconductors Preliminary data 1-of-8 FET multiplexer/demultiplexer FEATURES CBT3251 PIN CONFIGURATION • 5 Ω switch connection between two ports • TTL-compatible input levels • Minimal propagation delay through the switch • ESD protection exceeds 2000 V HBM per JESD22-A114, 16 VCC B4 1 200 V MM per JESD22-A115 and 1000 V CDM per JESD22-C101 • Latch-up testing is done to JESDEC Standard JESD78 which exceeds 100 mA B3 2 15 B5 B2 3 14 B6 B1 4 13 B7 A 5 12 B8 NC 6 11 S0 OE 7 10 S1 GND 8 9 S2 DESCRIPTION SA00570 The CBT3251 is a 1-of-8 high-speed TTL-compatible FET multiplexer/demultiplexer. The low on resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. PIN DESCRIPTION When output enable (OE) is low, the CBT3251 is enabled. S0, S1, and S2 select one of the B outputs for the A-input data. The CBT3251 is characterized for operation from –40 to +85°C. PIN NUMBER SYMBOL 1, 2, 3, 4, 12, 13, 14, 15 NAME AND FUNCTION B1, B2, B3, B4, B5, B6, B7, B8 5 A 6 NC No internal connection 7 OE Output enable 8 GND Ground (0 V) 9, 10, 11 S0, S1, S2 16 VCC B outputs A input Select-control input Positive supply voltage ORDERING INFORMATION TEMPERATURE RANGE ORDER CODE TOPSIDE MARK DWG NUMBER 16-pin plastic SOIC PACKAGES –40 to 85 °C CBT3251D CBT3251D SOT109-1 16-pin plastic SSOP –40 to 85 °C CBT3251DB CT3251 SOT338-1 16-pin plastic SSOP (QSOP) –40 to 85 °C CBT3251DS CBT3251 SOT519-1 16-pin plastic TSSOP –40 to 85 °C CBT3251PW CBT3251 SOT403-1 Standard packing quantities and other packaging data is available at www.philipslogic.com/packaging. 2002 Sep 09 2 Philips Semiconductors Preliminary data 1-of-8 FET multiplexer/demultiplexer CBT3251 LOGIC DIAGRAM (positive logic) 4 5 A 3 2 1 15 14 13 12 OE S0 S1 S2 B1 B2 B3 B4 B5 B6 B7 B8 7 11 10 9 SA00636 FUNCTION TABLE INPUTS FUNCTION OE S2 S1 S0 L L L L A port = B1 port L L L H A port = B2 port L L H L A port = B3 port L L H H A port = B4 port L H L L A port = B5 port L H L H A port = B6 port L H H L A port = B7 port L H H H A port = B8 port H X X X Disconnect 2002 Sep 09 3 Philips Semiconductors Preliminary data 1-of-8 FET multiplexer/demultiplexer CBT3251 ABSOLUTE MAXIMUM RATINGS1 PARAMETER SYMBOL CONDITIONS RATING UNIT V VCC DC supply voltage –0.5 to +7.0 VI DC input voltage2 –0.5 to +7.0 V 128 mA –50 mA –65 to +150 °C Continuous channel current IK Tstg Input clamp current VI/O < 0 Storage temperature range NOTES: 1. Stresses beyond those listed may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. RECOMMENDED OPERATING CONDITIONS SYMBOL LIMITS PARAMETER MIN MAX UNIT VCC DC supply voltage 4.5 5.5 V VIH High-level input voltage 2.0 — V VIL Low-level Input voltage — 0.8 V –40 +85 °C Tamb Operating free-air temperature range NOTE: 1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. DC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITIONS Tamb = –40 to +85 °C UNIT MIN TYP1 VIK Input clamp voltage VCC = 4.5 V; II = –18 mA — — –1.2 V VP Pass voltage VI = VCC = 5.5 V; I/O = –100 mA 3.4 3.6 3.9 V Input leakage current VCC = 5.5 V; VI = GND or 5.5 V — — ±1 µA Quiescent supply current VCC = 5.5 V; IO = 0, VI = VCC or GND — — 3 µA Control inputs2 VCC = 5.5 V, one input at 3.4 V, other inputs at VCC or GND — — 2.5 mA II ICC ∆ICC CI CIO(OFF) O(O ) ron3 Control pins Power off leakage current Power-off On-resistance VI= 3 V or 0 — 3.5 — pF A port VO = 3 V or 0; OE = VCC — 17.5 — pF B port VO = 3 V or 0; OE = VCC — 4.0 — pF VCC = 4 V; TYP @ VCC = 4 V; VI = 2.4 V; II = 15 mA — 14 20 Ω VCC = 4.5 V; VI = 0 V; II = 64 mA — 5 7 Ω VCC = 4.5 V; VI = 0 V; II = 30 mA — 5 7 Ω VCC = 4.5 V; VI = 2.4 V; II = 15 mA — 10 15 Ω NOTES: 1. All typical values are at VCC = 5 V, Tamb = 25 °C. 2. This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND 3. Measured by the voltage drop between the A and the B terminals at the indicated current through the switch. On-state resistance is determined by the lowest voltage of the two (A or B) terminals. 2002 Sep 09 MAX 4 Philips Semiconductors Preliminary data 1-of-8 FET multiplexer/demultiplexer CBT3251 AC CHARACTERISTICS Tamb = –40 to +85 °C; CL = 50 pF LIMITS SYMBOL PARAMETER FROM (INPUT) TO (OUTPUT) VCC = +5.0 V ±0.5 V MIN MAX UNIT tpd Propagation delay1 A or B B or A — 0.25 ns tpd Propagation delay S A 2 5.5 ns ten Output enable time to High and Low level Output disable time from High and Low level tdis S B 1.5 5.6 ns OE A or B 1.6 5.8 ns S B 1.9 6.4 ns OE A or B 2.3 6.2 ns NOTE: 1. The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). AC WAVEFORMS TEST CIRCUIT AND WAVEFORMS VM = 1.5V, VIN = GND to 3.0V 7V 3V 1.5 V 1.5 V 500 Ω From Output Under Test S1 Open GND INPUT 500 Ω CL = 50 pF 0V tPHL tPLH Load Circuit VOH 1.5 V 1.5 V OUTPUT VOL SA00028 Waveform 1. Input to Output Propagation Delays TEST S1 tpd open tPLZ/tPZL 7V tPHZ/tPZH open DEFINITIONS Load capacitance includes jig and probe capacitance; CL = see AC CHARACTERISTICS for value. 3V Output Control SA00012 1.5 V 1.5 V 0V tPLZ tPZL NOTES: 1. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. 2. The outputs are measured one at a time with one transition per measurement. 3.5 V Output Waveform 1 S1 at 7 V (see Note) 1.5 V VOL tPHZ tPZH Output Waveform 2 S1 at Open (see Note) VOL + 0.3 V VOH VOH – 0.3 V 1.5 V 0V Note: Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. SA00571 Waveform 2. 3-State Output Enable and Disable Times NOTES: 1. tPLZ and tPHZ are the same as tdis. 2. tPZL and tPZH are the same as ten. 3. tPLH and tPHL are the same as tpd. 2002 Sep 09 5 Philips Semiconductors Preliminary data 1-of-8 FET multiplexer/demultiplexer CBT3251 SO16: plastic small outline package; 16 leads; body width 3.9 mm 2002 Sep 09 6 SOT109-1 Philips Semiconductors Preliminary data 1-of-8 FET multiplexer/demultiplexer CBT3251 SSOP16: plastic shrink small outline package; 16 leads; body width 5.3 mm 2002 Sep 09 7 SOT338-1 Philips Semiconductors Preliminary data 1-of-8 FET multiplexer/demultiplexer CBT3251 SSOP16: plastic shrink small outline package; 16 leads; body width 3.9 mm; lead pitch 0.635 mm 2002 Sep 09 8 SOT519-1 Philips Semiconductors Preliminary data 1-of-8 FET multiplexer/demultiplexer CBT3251 TSSOP16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm 2002 Sep 09 9 SOT403-1 Philips Semiconductors Preliminary data 1-of-8 FET multiplexer/demultiplexer CBT3251 Data sheet status Data sheet status [1] Product status [2] Definitions Objective data Development This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. Preliminary data Qualification This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. Product data Production This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Changes will be communicated according to the Customer Product/Process Change Notification (CPCN) procedure SNW-SQ-650A. [1] Please consult the most recently issued data sheet before initiating or completing a design. [2] The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Koninklijke Philips Electronics N.V. 2002 All rights reserved. Printed in U.S.A. Contact information For additional information please visit http://www.semiconductors.philips.com. Fax: +31 40 27 24825 Date of release: 08-02 For sales offices addresses send e-mail to: [email protected]. 2002 Sep 09 Document order number: 10