MMIC AP230 Product Features Applications • Small size • NO matching circuit needed • High efficiency • Dual supply voltage • Higher linearity • Higher productivity • Lower manufacturing cost • GaAs MMIC • 3MHz – 2150MHz • -63dBc CSO 135 Channels@ output Level +37dBmV • -60dBc CTB 135 Channels@ output Level +37dBmV • -70dBc CSO 8 Channels@ output Level +45dBmV • -73dBc CTB 8 Channels@ output Level +45dBmV • Satellite • Repeater • Base Station • Converter • CATV • SMATV Package : SOIC-8 Descriptions The power amplifier is designed for base stations and repeater systems. GaAs MMIC is used and attached on a copper carrier of 8 pin air cavity package with dual supply voltage Operating Ranges PARAMETER UNIT Device Voltage VDC Case Temperature ℃ MIN TYP MAX +5 +5.3 - +85 -40 Absolute Minimum and Maximum Ratings PARAMETER UNIT Device Voltage VDC MIN MAX +5.5 Device Current mA +320 RF Input Power dBm +10 Storage Temperature ℃ -40 Specifications +150 T=25℃, Vcc=5.0V, 75Ω system P arame ter Units Frequ ency R an ge Sup ply Vo ltage Sin gle En d ed CATV Evalu ation Circui t Cu rren t S21 -Gain S21 -Gain S21 -Gain M Hz V S11 -In pu t Retu rn Los s S2 2-Outp u t R eturn L oss No ise Figu re OIP3 OIP1 dB dB dB m dB m S11 -In pu t Retu rn Los s S2 2-Outp u t R eturn L oss OIP3 OIP1 No ise Figu re C SO C TB 5 0 - 8 7 0M Hz XM D C SO 3 - 15 0M Hz C TB XM D dB dB dB m dB m dB dB c dB c dB c dB c dB c dB c mA dB dB dB M inimum Typical Max imum 3M Hz~2.1 5GHz 5 20 0 2 20 16 15 14 Reverse ( 3 ~ 2 00 M Hz ) -16 -16 5.5 43 21 Forward ( 5 0 ~ 87 0M Hz ) -11 -11 37 21 4 -63 -60 -55 -70 -73 -70 C ondition Vcc= 5V 2 50 3 M Hz 50 M Hz 2 15 0M Hz +5 d Bm /2 to ne separated b y 1M Hz At 10 0M Hz +5 d Bm /2 to ne separated b y 1M Hz At 80 0M Hz 1 3 5 chan n els ,+ 37 dB mV/ch ,Sing le 1 3 5 chan n els ,+ 37 dB mV/ch ,Sing le 1 3 5 chan n els ,+ 37 dB mV/ch ,Sing le 8 ch ann els,+4 5d Bm V/ch,Sin gle 8 ch ann els,+4 5d Bm V/ch,Sin gle 8 ch ann els,+4 5d Bm V/ch,Sin gle ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 6.0 MMIC AP230 Application 1 : Forward (50MHz ~ 2150MHz) Vcc Evaluation Board Layout 50-870MHz 4.7uF/16V 10nF 100nF 240 ohm 1nF 10nF RF IN 560nH 10nF RF OUT 1.8nH AP230 0.5pF 560nH 1nF 10nF 10nF D32212 10nF 10nF 240 ohm L1 680 ohm 10nF 100nF The transformers L1 and L2, used on the RFHIC evaluation board are hand wound baluns with following spec[L1=3.5turn, ferrite core (Ferronics 12-340-k), L2=3.5 turn, ferrite core(TDK,L6 RID 3*3*3 H1.2)] was used. φ0.12 1UEW wire was used. An SMT transformer (D32212,D31766), can also be used. 4.7uF/16V Vcc S-Parameters Noise Figure 6 20 15 5 5 Noise Figure(dB) Magnitude(dB) 5.5 S21 10 0 -5 S11 -10 -15 4.5 4 3.5 -20 S22 -25 3 -30 2.5 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 50 200 400 600 800 P1dB 25 1000 1200 1400 1600 1800 2000 2200 1400 1600 1800 2000 2200 Frequency(MHz) Frequency(GHz) OIP3 45 40 35 Noise Figure(dB) P1dB(dBm) 20 15 10 30 25 20 15 10 5 5 0 0 50 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 50 200 400 600 800 Frequency(MHz) Level: +37dBmV FRQ 1000 1200 Frequency(MHz) Tilt: 135CH FLAT XMD(NCTA) CTB_RAW CTB_COR N-FLR CSU_RAW CSU_COR CSU_FRQ CSL_RAW CSL_COR CSL_FRQ 55.25 59.8 69.4 69.5 84.7 83.8 88.1 56 68.7 68.8 54 77.25 59.9 68.7 68.8 85.1 69.3 69.5 78 84.5 88.8 76.51 109.25 60.1 66.4 66.4 84.9 82.9 87.2 109.99 69.1 69.2 107.99 211.25 60.4 66.2 66.2 83.8 80.9 83.9 212.49 68.7 68.8 209.99 331.25 60.4 65.6 65.6 82.7 76.9 78.2 332.49 69.3 69.5 329.99 445.25 61.2 66.2 66.2 83.4 76.5 77.6 446.5 71.7 72 443.99 547.25 62.9 66.7 66.8 81.7 74.8 75.7 548.5 72.5 73 545.98 637.25 63.4 66.2 66.3 82.3 75.4 76.5 638.5 75.2 76.2 635.99 745.25 64.5 65.5 65.6 81.4 73.4 74.2 746.49 76.1 77.5 743.98 859.25 64.8 65.1 65.3 80.3 72 72.8 860.49 75.8 78 857.99 ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 6.0 MMIC AP230 Application 2 : Reverse (3MHz ~ 200MHz) Vcc 4.7uF/16V Evaluation Board Layout 5-200MHz 100pF 1nF 22nF RF IN 4.7uH 3.3uF 100pF RF OUT 1uF AP230 R0 10 ohm D31250 1uF 3.3uF 22nF 7.5pF 4.7uH The transformers L1 and L2, used on the RFHIC evaluation board are hand wound baluns with following spec[L1=6 turn, ferrite core (TAIYO-YUDEN BF56 1.9*3.4*2.0), L2=3.5 turn, ferrite core(TDK,L6 RID 3*3*3 H1.2)] was used. φ0.12 1UEW wire was used. An SMT transformer (D31044,D31766), can also be used. 1nF 100pF Vcc 4.7uF/16V S-Parameters Noise Figure 30 8 7 S21 Noise Figure(dB) Magnitude(dB) 20 10 0 -10 S22 6 5 4 -20 S11 -30 3 5 0 30 60 90 120 150 180 210 240 270 300 5 Frequency(MHz) 50 100 150 200 250 Frequency(MHz) P1dB OIP3 50 25 45 OIP3(dBm) dBm 20 15 10 5 40 35 30 25 20 0 5 50 100 150 200 15 250 5 50 100 Frequency(MHz) Level: +45dBmV FRQ 150 200 250 Frequency(MHz) Tilt: 8CH FLAT XMD(NCTA) CTB_RAW CTB_COR N-FLR CSU_RAW CSU_COR 7 72.2 79.9 80.1 93.6 92.4 96.7 31 72.8 78.6 78.8 92.1 78.1 49 72.1 79.8 80.1 91.8 78.2 CSU_FRQ CSL_RAW CSL_COR CSL_FRQ 7.63 71.7 71.7 5.99 78.4 32 76.6 76.8 29.99 78.4 49.99 90.5 94.8 48.31 ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 6.0 MMIC AP230 ESD Protection For a safe use in all situations, it is recommended to have proper ESD control techniques while the device is being handled. Here are some recommended precautions; - Person at a workbench should be earthed via a wrist strap and a resistor. - All mains-powered equipment should be connected to the mains via an earth-leakage switch. - Equipment cases should be grounded. - Relative humidity should be maintained between 40% and 50%. - An ionizer is recommended. - Keep static materials, such as plastic envelopes and plastic trays etc. away from the workbench Package : SOIC-8 Type Block Diagram 1 2 3 4 AMP2 AMP1 PIN No Description 1 RF IN(2) 8 5 RF OUT(1) 7 4 RF IN(1) 6 8 RF OUT(2) 5 2, 3, 6, 7 GND Exposed slug GND Package Dimensions (Type: SOIC-8) Recommended Pattern RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 6.0