CMP350 SERIES Quad output • • • • • • • • [ 2 YEAR WARRANTY ] SPECIFICATION 10 x 5 inch footprint with 1.75 inch low profile EN61000-3-2 compliant Current sharing Individually protected outputs Power fail signals 350W with 300LFM EN55022, EN55011 conducted emissions level B UL, VDE and CSA safety approvals The CMP350 series is a 350W universal input AC/DC power supply in a 10 x 5 x 1.75 inch package. The series has the lowest standard 350W profile in the industry, input harmonic current emission correction as standard, current sharing and has 3.3V models to support the industry's transition from 5V to lower operating voltages. The CMP350 provides 350W of output power with 300LFM of forced air. Standard features include isolated outputs with individual overvoltage and overload protection on each output. The series has an enclosure with endmounted fans option that does not change the overall height. The series, with full international safety approval and the CE mark, meets conducted emissions EN55022 level B and has immunity compliance to EN61000-4-2,-3,-4, -5, -6. The CMP350 series is designed for use in medium power data networking, computer and telecom applications such as hubs, routers, file servers, graphic workstations and mass storage peripherals. It is also suitable for industrial, test and office applications. All specifications are typical at nominal input, full load at 25°C unless otherwise stated EMC CHARACTERISTICS OUTPUT SPECIFICATIONS Output accuracy Total regulation (Line and load) Transient response ±1.0% Main and auxiliary V1 output Auxiliary output (V2) Auxiliary output (V3) Main output 25% step load change at 1A/µs Temperature coefficient ±1.0% ±6.0% ±5.0% 2.0% max. dev., 500µs recovery ±0.02%/°C Ripple and noise (See Note 3) 0Hz to 20MHz 50mV pk-pk or 1.0% Overvoltage protection Latching Short circuit protection All channels Continuous, auto recovery Overload protection All channels Yes See table Conducted emissions Radiated emissions Harmonic current emission correction ESD air ESD contact Surge Fast transients Radiated immunity Conducted immunity EN55022, FCC part 15 EN55022, FCC part 15 EN61000-3-2 EN61000-4-2 EN61000-4-2 EN61000-4-5 EN61000-4-4 EN61000-4-3 EN61000-4-6 Level Level Level Level Level Level Current sharing Auto shutdown, auto recovery Main output and Aux. 1 (5V and 3V3) ±10% of rating INPUT SPECIFICATIONS Input voltage range Universal 90 to 264VAC (30s brown-out at 85VAC) Input frequency range 47Hz to 63Hz Input surge voltage 300VAC Inrush current 264VAC, cold start Safety ground leakage current Input current Hold-up time 110VAC, 60Hz, 350W Efficiency Isolation voltage Approvals and standards 110VAC, 350W Input/output Input/chassis Output/output 3000VAC 1500VAC 50VDC UL, IEC approved Power factor 110/220VAC full load 6.3A 250V 0.97 min. 150kHz EN60950, VDE0805, UL1950, CSA C22.2 No. 950 2.0kg (4.4Ibs) Size (See Note C) Open frame Enclosed MTBF MIL-HDBK-217F Bellcore TR-NWT-332 10.0 x 5 x 1.75 inches 10.5 x 5 x 1.75 inches 212,707 hours 959,870 hours ENVIRONMENTAL SPECIFICATIONS Thermal performance Operating ambient, FL 0°C to +50°C Cooling 300LFM airflow required +50°C to +70°C, Derate to 50% load ambient on all channels Non-operating -40°C to +85°C Relative humidity Non-condensing Altitude Operating Non-operating 75A max. 4.2Arms max. 16ms 75% typical Weight 0.72mA Input fuse PAGE 62 20ms 3 3 3 3 3 3 GENERAL SPECIFICATIONS Switching frequency Thermal protection Level B Level A Compliant Vibration (See Note 15) 5Hz to 500Hz 5% to 95% RH 10,000 feet max. 30,000 feet max. 2.4G rms peak LOW TO MEDIUM POWER AC/DC POWER SUPPLIES | 350W AC/DC 350 Watt AC/DC high wattage power supplies with PFC OUTPUT CURRENT OUTPUT OUTPUT VOLTAGE TYPE 5V Main 0A TOTAL OVP ADJUST MODEL REGULATION THRESHOLD RANGE NUMBERS 50mV ±1.0% 5.75 to 6.75V +10, -5% CMP350-9604 RIPPLE MIN (1) MAX (3) (2) 50A 3.3V (2) Aux 1 1.0A 20A (8) 50mV ±1.0% 4.15 to 4.35V +20, -5% 12V (2) Aux 2 1.0A 10A (8) 120mV ±1.0% 13.2 to 14.5V ±5% 12V (2) Aux 3 0.5A 5.0A (8) 120mV ±5.0% Main 0A 50A 50mV ±1.0% 5.75 to 6.75V +10, -5% 13.2 to 14.5V ±5% 5V 12.6 to 15.2V (4) (2) Aux 1 1.0A 10A 120mV ±1.0% 12V (2) Aux 2 0.5A 5.0A 120mV ±5.0% Aux 3 0.5A 5.0A 50mV ±1.0% 5.75 to 6.75V (7) Main 0A 50A 50mV ±1.0% 5.75 to 6.75V +10, -5% 13.2 to 14.5V ±5% 5V (2) 5V (4) (2) Aux 1 1.0A 10A 120mV ±1.0% 12V (2) Aux 2 0.5A 5.0A 120mV ±5.0% 24V (2) Aux 3 0.2A 2.0A 240mV ±1.0% 26.4 to 28.8V (7) Main 0A 50A 50mV ±1.0% 5.75 to 6.75V +10, -5% 16.5 to 18.0V ±5% 5V (4) (2) Aux 1 0.8A 8.0A 150mV ±1.0% 15V (2) Aux 2 0.4A 4.0A 150mV ±5.0% 24V (2) Aux 3 0.2A 2.0A 240mV ±1.0% 26.4 to 28.8V (7) Main 0A 50A 50mV ±1.0% 5.75 to 6.75V +10, -5% 13.2 to 14.5V ±5% 5V (4) (2) Aux 1 1.0A 10A 120mV ±1.0% 12V (2) Aux 2 0.5A 5.0A 120mV ±5.0% 12V (2) Aux 3 0.3A 3.0A 120mV ±1.0% 13.2 to 14.5V (7) Main 0A 50A 50mV ±1.0% 4.15 to 4.35V +20, -5% Aux 1 1.0A 15A (9) 50mV ±1.0% 5.75 to 6.75V +10, -5% 13.2 to 14.5V ±5% 3.3V 5V (2) (4) (2) Aux 2 0.5A 5.0A (9) 120mV ±1.0% 12V (2) Aux 3 0.5A 5.0A (9) 120mV ±5.0% 24V Main 0A 10A 240mV ±1.0% 26.4 to 28.8V ±5% 5V Aux 1 1.0A 15A 50mV ±1.0% 5.75 to 6.75V +10, -5% 12V Aux 2 1.0A 10A 120mV ±1.0% 13.2 to 14.5V ±5% 12V Aux 3 5.0A 5.0A 120mV ±5.0% 12.6 to 15.2V CMP350-9606 CMP350-9603 (5) 12V 12.6 to 15.2V CMP350-9602 (5) 12V 12.6 to 15.2V CMP350-9601 (5) 15V 15.7 to 19.0V 1 (5) 12V 12.6 to 15.2V (8) (6) 12V 12.6 to 15.2V (A) (4) CMP350-9692 (9) (6) (4) CMP350-9623 (6) DERATING CURVE (See Notes 10, 11) Output Power (Watts) 350W International Safety Standard Approvals 300LFM FORCED AIR COOLING VDE0805/EN60950/IEC950 Licence No. 96709 175W UL1950 File No. E136005 CSA C22.2 No. 950 File No. LR41062C 20W 0W 20W MINIMUM LOAD REQUIRED TO MAINTAIN REGULATION 0°C 10°C http://www.artesyn.com 20°C 30°C 40°C 50°C 60°C 70°C PAGE 63 350W AC/DC | LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 350 Watt AC/DC high wattage power supplies with PFC TB1 1 VMAIN + 3 VMAIN J1 1 TOP VIEW TB2 8 Notes: There are three external accessible connectors in the unit besides the main Busbar. The first one is designated as TB1 which is the input power connector. Pin assignment (TB1) Main output connector Input connector TB1 is a standard screw type terminal block. An IEC type connector is provided on enclosed models (suffix ‘CF’). Main output Busbar connector VMAIN+ and VMAIN-. PIN CONNECTIONS Input connector TB1 PIN NO. FUNCTION TB1-1 Live TB1-2 Ground TB1-3 Neutral PIN CONNECTIONS Output Busbar connector PIN NO. FUNCTION VMAIN+ Positive VMAINNegative Auxiliary output pin assignment (TB2) TB2 auxiliary output connector is used on models -9601, -9602, -9603, -9606. PIN CONNECTIONS (TB2) REFERENCE FUNCTION AUX CH. 1 Positive AUX CH. 1 Positive AUX CH. 1 Negative AUX CH. 1 Negative AUX CH. 2 Positive AUX CH. 2 Negative AUX CH. 3 Positive AUX CH. 3 Negative PIN NO. TB2-1 TB2-2 TB2-3 TB2-4 TB2-5 TB2-6 TB2-7 TB2-8 Auxiliary output pin assignment (TB2 and TB3) TB2 and TB3 auxiliary output connectors are used on models -9604 and -9692. See page 66 for detail. PIN NO. TB2-1 TB2-2 TB2-3 TB2-4 TB2-5 TB2-6 TB3-1 TB3-2 PIN CONNECTIONS (TB2 AND TB3) REFERENCE FUNCTION AUX CH. 2 Positive AUX CH. 2 Positive AUX CH. 2 Negative AUX CH. 2 Negative AUX CH. 3 Positive AUX CH. 3 Negative AUX CH. 1 Positive AUX CH. 1 Negative PAGE 64 USER INTERFACE PIN (J1) PIN NO. REFERENCE J1-3 12CH1 J1-4 12CH2 J1-5 J1-6 * J1-7 J1-8 J1-9 J1-10 J1-12 J1A-1 * J1A-2 * J1A-3 * J1A-6 * J1A-7 * J1A-8 J1A-9 J1A-10 J1A-11 J1A-12 (B) FUNCTION 12V Bias Refd. to Main Ch. -ve 12V Bias Refd. to Aux. Ch. #1 -ve, (-9601, -9602, -9603, -9606) 12V Bias Refd. to Aux. Ch. #2 -ve, (-9604, -9692) VSENMAIN+ Main Ch. Positive Remote Sense AUX1SET (See Note 14) GND2 Ground Refd. to Aux. Ch. #1 -ve, (-9601, -9602, -9603, -9606) Ground Refd. to Aux. Ch. #2 -ve, (-9604, -9692) POK (13) Power Good Detect Signal GND1 Ground Refd. to Main Ch. -ve PFD (13) Power Fail Detect Signal VSENMAINMain Ch. Negative Remote Sense VAUXSEN- Auxiliary Channel Negative Remote Sense VAUXSEN+ Auxiliary Channel Positive Remote Sense GND3 Ground Refd. to Aux. Ch. 1 +ve for -9604 and -9692 models CSAUX (12) Auxiliary Channel Current Share Pin TRIMAUX2 Tim Pin for 5V or 3.3V Auxiliary Channel CSMAIN (12) Main Channel Current Share Pin INHIBITInhibit Signal Return INHIBIT+ Inhibit Signal TRIMAUX Trim Pin for 12V or 15V Auxiliary Channel TRIMAIN Main Channel Trim Pin * Applies to -9604, -9692 models only. LOW TO MEDIUM POWER AC/DC POWER SUPPLIES | 350W AC/DC 350 Watt AC/DC high wattage power supplies with PFC Notes FEATURES 1 Current share (See Note 12) Forced Main output and auxiliary 1 if 5V or 3.3V Power OK (See Note 13) Asserted Low Remote-sense 0.4V Main output >75% Main output and auxiliary 1 if 5V or 3.3V System inhibit Asserted high Power fail detect (See Note 13) Asserted low 2 3 Inhibits all outputs 4 5 6 7 8 The unit must be powered up into the recommended minimum loads to ensure the outputs come up. Combined maximum output power for Aux. 1, 2 and 3 is 220W. For models -9604 and -9692, on the aux 1 channel, output ripple and noise is measured 6 inches down the output cables through a 1 foot long twisted pair terminated with a parallel combination of a 10µF electrolytic and a 0.1µF ceramic capacitors. For all other channels on all models, ripple and noise is measured directly at the output terminals. No shutdown or latch-up occurs; voltage is internally limited to specified range. Aux. 2 tracks Aux. 3, Aux. 4 not adjustable. Aux. 3 tracks Aux. 2. Output is not adjustable. CMP350-9604 rated operation: Indicates loss of AC 4ms warning Graph 1 8A 15A 10A 10A Sum of 12V Channel Loads* AC INPUT 5A RATED OPERATION OUTPUT 0A 5A 10A 15A 20A 3.3 V Channel Load PFD SIGNAL POWER GOOD SIGNAL t1 * Max. load for AUX2 is 10A Max load for AUX3 is 5A t2 t1 Varies with line and load t2 ≥ 4ms t1 + t2 ≥ 20ms 9 EXTERNAL OUTPUT TRIMMING The auxiliary channels must share power as indicated by graph 1. The maximum output power is 220W. CMP350-9692 rated operation: (14) Graph 2 8A 15A Main channel trim connections 10A 12CH1 Sum of 12V Channel Loads* TRIM UP/DOWN TRIMAIN TRIM DOWN TRIM UP 10A RATED OPERATION 5A 0A 5A 10A 15A 5V Channel Load * Max. load for AUX2 is 10A Max load for AUX3 is 5A GND1 Aux. 1 channel trim connections. (-9601, -9602, -9603, 9606) Aux. 2 channel trim connections (-9604, -9692) 12CH2 10 11 12 TRIM UP/DOWN TRIMAUX TRIM DOWN TRIM UP 13 The auxiliary channels must share power as indicated by graph 2. The maximum output power is 220W. A minimum of 300LFM of forced air cooling is required for proper operation of the CMP350. All outputs must be derated linearly from maximum specified loads during operation above 50°C. Current share is a single wire share circuit that allows the main output on multiple CMP350 units to be operated in parallel. Auxiliary channels share on -9604 and -9692 models by connecting the CSAUX channel. The power fail detect and power OK signals are open-collector outputs which will sink 40mA or less in the low state and should be pulled up to a bias voltage with an appropriately sized resistor. GND2 Aux. 1 channel trim connections (-9604, -9692) AUX1SET GND3 TRIM UP/DOWN TRIMAUX2 TRIMAUX2 is connected to AUX1SET by a factory fitted jumper to ensure CH. 1 regulates at the nominal set voltage TRIMAUX2 To trim CH1, remove the jumper and connect a resistor between GND3 and TRIMAUX2 http://www.artesyn.com VOL IOL VOH Min. 0V 0A 4V Max. 0.4V -40mA 40V The system inhibit and output inhibit signals require a current source to be asserted high. Min. Max. VIH 3.5V 15.0V IIH 0mA -10mA 14 Connection from TRIMAUX2 to AUX1SET causes the output for Ch. aux. 1 on models -9604 and -9692 to regulate at its nominal factory set voltage. 15 3 orthogonal axes, random vibration, 10 minute test per axes. 16 This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. PAGE 65 1 350W AC/DC | LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 350 Watt AC/DC high wattage power supplies with PFC Mechanical notes A A standard cover and fan assembly can be added during manufacturing. To order, add suffix 'CF' to the model number. e.g. CMP350-9601CF. B Visual arrangement for J1 as seen from the front (output) side of the unit. C The dimensions of the CMP350-9604 and CMP350-9692 are slightly larger than shown below. The open frame dimensions are 10.2 x 5 x 1.75 inches and the enclosed dimensions are 10.7 x 5 x 1.75 inches. 2.250 (57.15) 6.500 (165.1) Third Angle Projection 0.870 (22.098) 0.164-32-UNC-2B (6 Places) (2 On Side, 4 On Bottom) 3/16" (4.76) Max. Thread Penetration - Typ. 0.410 (10.414) 9.90 (251.46) AC Input Terminal Block 1.75 (44.45) 1/4 - 20 UNC Thread Output Studs HI GND LO TB1 J1 3.900 (99.06) TB2 5.00 +0.00/-0.02 (127.00) 1 8 8 0.125 REF. (3.175) 0.400 (10.160) 6.500 (165.100) 2.250 (57.150) 10.000 (254.000) See Mechanical Note C ALL DIMENSIONS IN INCHES (mm) Tolerances unless otherwise specified .xx = ± 0.02 .xxx = ± 0.010 Detail: Mating connectors (J1) mating connector type Molex P/N 22-55-2241 or equivalent with Molex P/N 70058 or equivalent crimp terminals. J1-1 J1A-12 VMAIN + Input connector VMAIN - IEC for all enclosed models (suffix ‘-CF’). 3-way 0.375 inch pitch terminal block for uncovered models. J1 1 Output connectors 2 (TB2) connector type For models -9601, -9602, -9603 and -9606 8-way 0.197 inch pitch terminal. TB2 6 J1-12 (TB2) connector type For models -9604 and -9692 6-way 0.197 inch pitch terminal block. J1A-1 User Interface Connector J1 View Vertical mount 2 row, 24 position TB2 is a 6 way connector on models 9604 and -9692 as shown above. Data Sheet © Artesyn Technologies® 2000 The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. PAGE 66 DS_CMP350_20000101.PDF (TB3) connector type For models -9604 and -9692. 2-way 0.375 inch pitch terminal block. TB3 1