[ /Title (CD74 HC435 1, CD74 HCT43 51, CD74 HC435 2) /Subject (High Speed CMOS Logic Analog Multiplexers/De multiplexers with Latch) /Autho r () /Keywords (High Speed CMOS Logic CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Data sheet acquired from Harris Semiconductor SCHS213C September 1998 - Revised July 2003 High-Speed CMOS Logic Analog Multiplexers/Demultiplexers with Latch Features CMOS technology to achieve operating speeds similar to LSTTL with the low power consumption of standard CMOS integrated circuits. • Wide Analog Input Voltage Range . . . . . . . . . ±5V (Max) • Low “On” Resistance - VCC - VEE = 4.5V. . . . . . . . . . . . . . . . . . . . . . 70Ω (Typ) - VCC - VEE = 9V . . . . . . . . . . . . . . . . . . . . . . . 40Ω (Typ) These analog multiplexers/demultiplexers are, in essence, the HC/HCT4015 and HC4052 preceded by address latches that are controlled by an active low Latch Enable input (LE). Two Enable inputs, one active low (E1), and the other active high (E2) are provided allowing enabling with either input voltage level. • Low Crosstalk Between Switches • Fast Switching and Propagation Speeds • “Break-Before-Make” Switching Ordering Information • Wide Operating Temperature Range . . . -55oC to 125oC • HC Types - 2V to 6V Operation, Control; 0V to 10V Switch - High Noise Immunity: NIL = 30%, NIH = 30% of VCC at VCC = 5V TEMP. RANGE (oC) PACKAGE CD54HC4351F3A -55 to 125 20 Ld CERDIP CD74HC4351E -55 to 125 20 Ld PDIP CD74HC4351M -55 to 125 20 Ld SOIC CD74HC4351M96 -55 to 125 20 Ld SOIC CD74HCT4351E -55 to 125 20 Ld PDIP CD74HC4352E -55 to 125 20 Ld PDIP PART NUMBER • HCT Types - 4.5V to 5.5V Operation, Control; 0V to 10V Switch - Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min) - CMOS Input Compatibility, Il ≤ 1µA at VOL, VOH Description NOTE: When ordering, use the entire part number. The suffix 96 denotes tape and reel. The ’HC4351, CD74HCT4351, and CD74HC4352 are digitally controlled analog switches which utilize silicon-gate Pinouts CD54HC4351 (CERDIP) CD74HC4351 (PDIP, SOIC) CD74HCT4351 (PDIP) TOP VIEW A4 1 CD74HC4352 (PDIP) TOP VIEW 20 VCC B0 1 B2 2 19 A2 NC 3 18 A1 B COMMON 4 17 A COMMON 5 16 A0 A6 2 19 A2 B3 NC 3 18 A1 B1 6 15 A3 A COMMON 4 17 A0 E1 7 14 NC A7 5 16 A3 E2 8 13 S0 VEE 9 12 S1 GND 10 11 LE A5 6 15 S0 E1 7 14 NC E2 8 13 S1 VEE 9 12 S2 GND 10 11 LE CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright 20 VCC © 2003, Texas Instruments Incorporated 1 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Functional Diagram ’HC4351, CD74HCT4351 CHANNEL IN/OUT VCC 20 A7 A6 A5 A4 A3 A2 A1 A0 5 2 6 1 16 19 18 17 TG S0 15 TG S1 13 S2 12 TG LATCHES TG BINARY TO 1 OF 8 DECODER WITH ENABLE LOGIC LEVEL CONVERSION LE 11 4 A COMMON OUT/IN TG TG E1 TG 7 TG E2 8 10 GND 9 VEE TRUTH TABLE ’HC4351, CD74HCT4351 INPUT STATES E1 E2 S2 S1 S0 (NOTE 1) “ON” SWITCHES LE = H L H L L L A0 H L L H A1 L H L H L A2 L H L H H A3 L H H L L A4 L H H L H A5 L H H H L A6 L H H H H A7 H L X X X None FROM SELECT LOGIC P P VCC VCC N N N N VEE FIGURE 1. DETAIL OF ONE HC/HCT4351 SWITCH H = High Voltage Level, L = Low Voltage Level, X = Don’t Care NOTE: 1. When LE is low S0-S2 data are latched and switches cannot change state. 2 A COMMON IN/OUT L An IN/OUT CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Functional Diagram CD74HC4352 A CHANNELS IN/OUT VCC A3 A2 A1 A0 15 19 18 16 20 TG S0 13 S0 S0 LATCHES S1 12 LE TG S1 TG S1 BINARY TO 1 OF 4 DECODER WITH ENABLE LOGIC LEVEL CONVERSION 11 TG 17 A COMMON OUT/IN TG 4 B COMMON OUT/IN TG E1 7 E2 8 TG TG 10 9 GND 5 2 6 1 B0 B1 B2 B3 B CHANNELS IN/OUT VEE TRUTH TABLE CD74HC4352 An (Bn) IN/OUT INPUT STATES E1 E2 S1 S0 FROM SELECT LOGIC (NOTE 2) “ON” SWITCHES LE = H H L L A0, B0 L H L H A1, B1 L H H L A2, B2 L H H H A3, B3 H L X X None VCC N N N N VEE H = High Voltage Level, L = Low Voltage Level, X = Don’t Care NOTE: FIGURE 2. DETAIL OF ONE CD74HC4352 SWITCH 2. When Latch Enable is “Low” channel-select data is latched and switches cannot change state. 3 A COMMON (B COMMON) IN/OUT L P P VCC CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Supply Voltage, VCC - VEE . . . . . . . . . . . . . . . . . . -0.5V to 10.5V DC Supply Voltage, VEE . . . . . . . . . . . . . . . . . . . . . . . . 0.5V to -7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC 0.5V. . . . . . . . . . . . . . . . . . . . . . . .±20mA DC Switch Diode Current, IOK For VI < VEE -0.5V or VI < VCC + 0.5V . . . . . . . . . . . . . . . . .±25mA DC Switch Current, IOK (Note 3) For VI > VEE -0.5V or VI < VCC + 0.5V . . . . . . . . . . . . . . . . .±20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±20mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±25mA DC VCC or Ground Current, ICC . . . . . . . . . . . . . . . . . . . . . . . . .±50mA Thermal Resistance (Typical, Note 4) θJA (oC/W) E (PDIP) Package . . . . . . . . . . . . . . . . . . . . . . . . . . 69 M (SOIC) Package. . . . . . . . . . . . . . . . . . . . . . . . . . 58 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V Supply Voltage Range, VCC - VEE HC, HCT Types (Figure 3) . . . . . . . . . . . . . . . . . . . . . . .2V to 10V Supply Voltage Range, VEE HC, HCT Types (Figure 4) . . . . . . . . . . . . . . . . . . . . . . . 0V to -6V DC Input or Output Voltage, VI . . . . . . . . . . . . . . . . . . . GND to VCC Analog Switch I/O Voltage, VIS . . . . . . . . . . . . . . . . . . . . . VEE (Min) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC (Max) Input Rise and Fall Time, tr, tf 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 3. In certain applications, the external load-resistor current may include both VCC and signal-line components. To avoid drawing VCC current when switch current flows into the transmission gate inputs, the voltage drop across the bidirectional switch must not exceed 0.6V (calculated from RON values shown in the DC Electrical Specifications table). No VCC current will flow through RL if the switch current flows into terminal 3 on the ’HC4351 and CD74HCT4351; terminals 3 and 13 on the CD74HC4352. 4. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Area as a Function of Supply Voltage 8 6 VCC - GND (V) 4 8 6 VCC - GND (V) 4 HCT HC 2 0 HCT HC 2 0 2 0 4 6 8 10 12 VCC - VEE (V) FIGURE 3. 0 -2 -4 -6 -8 VEE - GND (V) FIGURE 4. 4 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 DC Electrical Specifications PARAMETER -40oC TO 85oC 25oC TEST CONDITIONS -55oC TO 125oC SYMBOL VI (V) VIS (V) VEE (V) VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS VIH - - - 2 1.5 - - 1.5 - 1.5 - V 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V 0 4.5 - 70 160 - 200 - 240 Ω 0 6 - 60 140 - 175 - 210 Ω -4.5 4.5 - 40 120 - 150 - 180 Ω 0 4.5 - 90 180 - 225 - 270 Ω 0 6 - 80 160 - 200 - 240 Ω -4.5 4.5 - 45 130 - 162 - 195 Ω 0 4.5 - 10 - - - - - Ω 0 6 - 8.5 - - - - - Ω -4.5 4.5 - 5 - - - - - Ω 0 6 - - ±0.1 - ±1 - ±1 µA -5 5 - - ±0.2 - ±2 - ±2 µA 0 6 - - ±0.2 - ±2 - ±2 µA -5 5 - - ±0.4 - ±4 - ±4 µA HC TYPES High Level Input Voltage Low Level Input Voltage “ON” Resistance IO = 1mA Figure 9 VIL RON - VIH or VIL - VCC or VEE VCC to VEE Maximum “ON” Resistance Between Any Two Channels Switch On/Off Leakage Current 4 Channels (4352) ∆RON IIZ - VIH or VIL Switch On/Off Leakage Current 8 Channels (4351) - For Switch OFF: When VIS = VCC VOS = VEE; When VIS = VEE, VOS = VCC For Switch ON: All Applicable Combinations of VIS and VOS Voltage Levels - Control Input Leakage Current IIL VCC or GND - 0 6 - - ±0.1 - ±1 - ±1 µA Quiescent Device Current IO = 0 ICC VCC or GND When VIS = VEE, VOS = VCC, When VIS = VCC, VOS = VEE 0 6 - - 8 - 80 - 160 µA -5 5 - - 16 - 160 - 320 µA 5 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 DC Electrical Specifications (Continued) SYMBOL VI (V) VIS (V) VEE (V) VCC (V) High Level Input Voltage VIH - - - Low Level Input Voltage VIL - - “ON” Resistance IO = 1mA Figure 9 RON VIH or VIL VCC or VEE PARAMETER -40oC TO 85oC 25oC TEST CONDITIONS -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 4.5 to 5.5 2 - - 2 - 2 - V - 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V 0 4.5 - 70 160 - 200 - 240 Ω -4.5 4.5 - 40 120 - 150 - 180 Ω 0 4.5 - 90 180 - 225 - 270 Ω -4.5 4.5 - 45 130 - 162 - 195 Ω 0 4.5 - 10 - - - - - Ω -4.5 4.5 - 5 - - - - - Ω 0 6 - - ±0.1 - ±1 - ±1 µA -5 5 - - ±0.2 - ±2 - ±2 µA 0 6 - - ±0.2 - ±2 - ±2 µA -5 5 - - ±0.4 - ±4 - ±4 µA 0 5.5 - - ±0.1 - ±1 - ±1 µA 0 5.5 - - 8 - 80 - 160 µA -4.5 5.5 - - 16 - 160 - 320 µA - 4.5 to 5.5 - 100 360 - 450 - 490 µA HCT TYPES VCC to VEE Maximum “ON” Resistance Between Any Two Channels Switch On/Off Leakage Current 4 Channels (4352) ∆RON IIZ - VIH or VIL Switch On/Off Leakage Current 8 Channels (4351) Control Input Leakage Current Quiescent Device Current IO = 0 Additional Quiescent Device Current Per Input Pin: 1 Unit Load II VCC or GND ICC - For Switch OFF: When VIS = VCC VOS = VEE; When VIS = VEE, VOS = VCC For Switch ON: All Applicable Combinations of VIS and VOS Voltage Levels - Any When Voltage VIS = VEE, BeVOS = VCC, tween When VCC VIS = VCC, and VOS = VEE GND ∆ICC (Note 5) VCC -2.1 - NOTE: 5. For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table TYPE INPUT UNIT LOADS All E1, E2, Sn 0.5 (4351, 4352) LE 1.5 NOTE: Unit Load is ∆ICC limit specified in DC Electrical Table, e.g., 360µA max at 25oC. 6 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Switching Specifications Input tr, tf = 6ns -40oC TO 85oC 25oC PARAMETER -55oC TO 125oC SYMBOL TEST CONDITIONS VEE (V) VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tPLH, tPHL CL = 50pF 0 2 - - 35 - 45 - 55 ns 0 4.5 - - 7 - 9 - 11 ns 0 6 - - 6 - 8 - 9 ns -4.5 4.5 - - 5 - 7 - 8 ns 0 2 - - 300 - 375 - 450 ns 0 4.5 - - 60 - 75 - 90 ns 0 6 - - 51 - 64 - 77 ns -4.5 4.5 - - 55 - 69 - 83 ns CL = 15pF - 5 - 27 - - - - - ns CL = 50pF 0 2 - - 350 - 440 - 525 ns 0 4.5 - - 70 - 88 - 105 ns 0 6 - - 60 - 75 - 90 ns -4.5 4.5 - - 60 - 75 - 90 ns CL = 15pF - 5 - 35 - - - - - ns CL = 50pF 0 2 - - 300 - 375 - 450 ns 0 4.5 - - 60 - 75 - 90 ns 0 6 - - 51 - 64 - 77 ns -4.5 4.5 - - 50 - 63 - 75 ns CL = 15pF - 5 - 27 - - - - - ns CL = 50pF 0 2 - - 375 - 470 - 565 ns 0 4.5 - - 75 - 94 - 113 ns 0 6 - - 64 - 80 - 96 ns -4.5 4.5 - - 55 - 69 - 83 ns CL = 15pF - 5 - 35 - - - - - ns CL = 50pF 0 2 - - 250 - 315 - 375 ns 0 4.5 - - 50 - 63 - 75 ns 0 6 - - 43 - 54 - 64 ns -4.5 4.5 - - 40 - 50 - 60 ns - 5 - 21 - - - - - ns HC TYPES Propagation Delay, Switch In to Switch Out Maximum Switch Turn “ON” Delay 4351 E1, E2, LE to VOS Maximum Switch Turn “ON” Delay 4352 E1, E2, LE to VOS Maximum Switch Turn “ON” Delay 4351 Sn to VOS Maximum Switch Turn “ON” Delay 4352 Sn to VOS Maximum Switch Turn “OFF” Delay 4351 E1 to VOS tPZH, tPZL tPZH, tPZL tPZH, tPZL tPZH, tPZL tPHZ, tPLZ CL = 50pF CL = 15pF 7 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Switching Specifications Input tr, tf = 6ns (Continued) -40oC TO 85oC 25oC PARAMETER Maximum Switch Turn “OFF” Delay 4351 E2 to VOS Maximum Switch Turn “OFF” Delay 4351 LE to VOS Maximum Switch Turn “OFF” Delay 4351 Sn to VOS Maximum Switch Turn “OFF” Delay 4352 E1, E2, LE to VOS Setup Time 4351 Sn to LE Hold Time 4351 and 4352 Sn to LE Pulse Width 4351 and 4352 LE Input (Control) Capacitance Power Dissipation Capacitance (Notes 6, 7) 4351 -55oC TO 125oC SYMBOL TEST CONDITIONS VEE (V) VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS tPHZ, tPLZ CL = 50pF 0 2 - - 250 - 315 - 375 ns 0 4.5 - - 50 - 63 - 75 ns 0 6 - - 43 - 54 - 64 ns -4.5 4.5 - - 40 - 50 - 60 ns CL = 15pF - 5 - 21 - - - - - ns CL = 50pF 0 2 - - 275 - 345 - 415 ns 0 4.5 - - 55 - 69 - 83 ns 0 6 - - 47 - 59 - 71 ns -4.5 4.5 - - 45 - 56 - 68 ns 0 2 - - 275 - 345 - 415 ns 0 4.5 - - 55 - 69 - 83 ns 0 6 - - 47 - 59 - 71 ns -4.5 4.5 - - 48 - 60 - 71 ns CL = 15pF - 5 - 21 - - - - - ns CL = 50pF 0 2 - - 275 - 345 - 415 ns 0 4.5 - - 55 - 69 - 83 ns 0 6 - - 47 - 59 - 71 ns -4.5 4.5 - - 50 - 63 - 75 ns CL = 15pF - 5 - 21 - - - - - ns CL = 50pF 0 2 - - 60 - 75 - 90 ns 0 4.5 - - 12 - 15 - 18 ns 0 6 - - 10 - 13 - 15 ns -4.5 4.5 - - 18 - 23 - 27 ns 0 2 5 - - 5 - 5 - ns 0 4.5 5 - - 5 - 5 - ns 0 6 5 - - 5 - 5 - ns -4.5 4.5 5 - - 5 - 5 - ns 0 2 100 - - 125 - 150 - ns 0 4.5 20 - - 25 - 30 - ns 0 6 17 - - 21 - 26 - ns -4.5 4.5 25 - - 31 - 38 - ns tPHZ, tPLZ tPHZ, tPLZ tPHZ, tPLZ tSU tH tW CL = 50pF CL = 50pF CL = 50pF CI - - - - - 10 - 10 - 10 pF CPD - - 5 - 50 - - - - - pF 8 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Switching Specifications Input tr, tf = 6ns (Continued) -40oC TO 85oC 25oC -55oC TO 125oC PARAMETER SYMBOL TEST CONDITIONS VEE (V) VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS Power Dissipation Capacitance (Notes 6, 7) 4352 CPD - - 5 - 74 - - - - - pF tPLH, tPHL CL = 50pF 0 4.5 - - 7 - 9 - 11 ns -4.5 4.5 - - 5 - 7 - 8 ns 0 4.5 - - 75 - 94 - 113 ns -4.5 4.5 - - 60 - 75 - 90 ns CL = 15pF - 5 - 35 - - - - - ns CL = 50pF 0 4.5 - - 75 - 94 - 113 ns -4.5 4.5 - - 60 - 75 - 90 ns CL = 15pF - 5 - 35 - - - - - ns CL = 50pF 0 4.5 - - 55 - 69 - 83 ns -4.5 4.5 - - 40 - 50 - 60 ns CL = 15pF - 5 - 23 - - - - - ns CL = 50pF 0 4.5 - - 60 - 75 - 90 ns -4.5 4.5 - - 50 - 63 - 75 ns CL = 15pF - 5 - 23 - - - - - ns CL = 50pF 0 4.5 - - 60 - 75 - 90 ns -4.5 4.5 - - 55 - 69 - 83 ns 0 4.5 - - 65 - 81 - 98 ns -4.5 4.5 - - 55 - 69 - 83 ns CL = 15pF - 5 - 23 - - - - - ns CL = 50pF 0 4.5 - - 12 - 15 - 18 ns -4.5 4.5 - - 14 - 18 - 21 ns 0 4.5 5 - - 5 - 5 - ns -4.5 4.5 5 - - 5 - 5 - ns 0 4.5 25 - - 31 - 28 - ns -4.5 4.5 25 - - 31 - 38 - ns HCT TYPES Propagation Delay, Switch In to Switch Out Maximum Switch Turn “ON” Delay 4351 E1, E2, LE to VOS Maximum Switch Turn “ON” Delay 4351 Sn to VOS Maximum Switch Turn “OFF” Delay 4351 E1 to VOS Maximum Switch Turn “OFF” Delay 4351 E2 to VOS tPZH, tPZL tPZH, tPZL tPHZ, tPLZ tPHZ, tPLZ Maximum Switch Turn “OFF” Delay 4351 LE to VOS tPHZ, tPLZ Maximum Switch Turn “OFF” Delay 4351 Sn to VOS tPHZ, tPLZ Setup Time 4351 Sn to LE Hold Time 4351 and 4352 Sn to LE Pulse Width 4351 LE Input (Control) Capacitance Power Dissipation Capacitance (Notes 6, 7) 4351 CL = 50pF CL = 50pF CL = 50pF tW CL = 50pF CI - - - - - 10 - 10 - 10 pF CPD - - 5 - 52 - - - - - pF NOTES: 6. CPD is used to determine the dynamic power consumption, per package. 7. PD = CPD VCC2 fi + Σ (CL + CS) VCC2 fo where fi = input frequency, fo = output frequency, CL = output load capacitance, CS = switch capacitance, VCC = supply voltage. 9 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Analog Channel Specifications PARAMETER Switch Input Capacitance Common Capacitance Minimum Switch Frequency Response at -3dB (Figure 6, 8) TA = 25oC SYMBOL TEST CONDITIONS TYPE VEE (V) VCC (V) HC/HCT UNITS CI All - - 5 pF CCOM 4351 - - 25 pF 4352 - - 12 pF 4351 - - 145 MHz 4352 -2.25 2.25 165 MHz fMAX Crosstalk Between Any Two Switches (Note 11) Sine-Wave Distortion E or S to Switch Feedthrough Noise Switch “OFF” Signal Feedthrough (Figure 6, 8) See Figure 11 (Notes 8, 9) See Figure 10 (Notes 9, 10) See Figure 12 See Figure 13 (Notes 9, 10) See Figure 14 (Notes 9, 10) NOTES: 8. Adjust input voltage to obtain 0dBm at VOS for, fin = 1MHz. 9. VIS is centered at (VCC - VEE)/2. 10. Adjust input for 0dBm. 11. Not applicable for ’HC4351 and CD74HCT4351. 10 4351 - - 180 MHz 4352 -4.5 4.5 185 MHz 4351 - - N/A dB 4352 -2.25 2.25 (TBE) dB 4351 - - N/A dB 4352 -4.5 4.5 (TBE) dB All -2.25 2.25 0.035 % All -4.5 4.5 0.018 % 4351 - - - mV 4352 -2.25 2.25 (TBE) mV 4351 - - - mV 4352 -4.5 4.5 (TBE) mV 4351 - - -73 dB 4352 -2.25 2.25 -65 dB 4351 - - -75 dB 4352 -4.5 4.5 -67 dB CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Typical Performance Curves 0 0 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50Ω PIN 12 TO 3 -2 -4 -40 dB dB VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50Ω PIN 12 TO 3 -6 VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50Ω PIN 12 TO 3 -20 -60 -8 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50Ω PIN 12 TO 3 -80 -10 10K 100K 1M 10M FREQUENCY, f (Hz) -100 10K 100M FIGURE 5. CHANNEL ON BANDWIDTH (’HC4351, CD74HCT4351) 1M 10M FREQUENCY, f (Hz) 100M FIGURE 6. CHANNEL OFF FEEDTHROUGH (’HC4351, CD74HCT4351) 0 0 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50Ω PIN 4 TO 3 -2 -4 -40 dB dB VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50Ω PIN 4 TO 3 -20 VCC = 2.25V GND = -2.25V VEE = -2.25V RL = 50Ω PIN 4 TO 3 -6 -60 VCC = 4.5V GND = -4.5V VEE = -4.5V RL = 50Ω PIN 4 TO 3 -80 -8 -10 10K 100K 100K 1M 10M FREQUENCY, f (Hz) -100 10K 100M 100K 1M 10M 100M FREQUENCY, f (Hz) FIGURE 7. CHANNEL ON BANDWIDTH (CD74HC4352) FIGURE 8. CHANNEL OFF FEEDTHROUGH (CD74HC4352) 11 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 “ON” RESISTANCE, RON (Ω) Typical Performance Curves (Continued) 130 120 110 100 90 80 70 60 50 40 30 20 10 VCC - VEE = 4.5V VCC - VEE = 6V VCC - VEE = 9V 0 1 0 2 3 4 5 6 7 8 9 INPUT SIGNAL VOLTAGE, VIS (V) FIGURE 9. TYPICAL ON RESISTANCE vs INPUT SIGNAL VOLTAGE Analog Test Circuits VIS 0.1µF VCC VCC SWITCH ON VIS R VOS1 R R C VOS2 SWITCH OFF R VCC/2 VCC/2 C dB METER VCC/2 fIS = 1MHz SINEWAVE R = 50Ω C = 10pF FIGURE 10. CROSSTALK BETWEEN TWO SWITCHES TEST CIRCUIT VCC VCC 0.1µF VIS SINE WAVE 10µF VIS VOS SWITCH ON 50Ω VCC/2 VIS SWITCH ON VI = VIH VOS 10kΩ 10pF dB METER VCC/2 50pF DISTORTION METER fIS = 1kHz TO 10kHz FIGURE 11. FREQUENCY RESPONSE TEST CIRCUIT FIGURE 12. TOTAL HARMONIC DISTORTION TEST CIRCUIT 12 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Analog Test Circuits (Continued) E VCC 600Ω VCC/2 SWITCH ALTERNATING ON AND OFF tr, tf ≤ 6ns fCONT = 1MHz 50% DUTY CYCLE VCC VP-P VOS 0.1µF 600Ω 50pF VCC/2 SCOPE FIGURE 13. CONTROL-TO-SWITCH FEEDTHROUGH NOISE TEST CIRCUIT fIS ≥ 1MHz SINEWAVE R = 50Ω C = 10pF VOS SWITCH OFF VIS VOS VC = VIL R R VCC/2 VCC/2 C dB METER FIGURE 14. SWITCH OFF SIGNAL FEEDTHROUGH 13 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Test Circuits and Waveforms tWL + tWH = tfCL trCL tWL + tWH = trCL = 6ns tfCL = 6ns 50% 10% 10% 2.7V CLOCK 50% 50% 1.3V 0.3V 0.3V GND 1.3V 1.3V GND tWH tWL tWH tWL I fCL 3V VCC 90% CLOCK I fCL NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. NOTE: Outputs should be switching from 10% VCC to 90% VCC in accordance with device truth table. For fMAX, input duty cycle = 50%. FIGURE 15. HC CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH FIGURE 16. HCT CLOCK PULSE RISE AND FALL TIMES AND PULSE WIDTH tr = 6ns tf = 6ns 90% 50% 10% INPUT GND tTLH 90% INVERTING OUTPUT tPHL FIGURE 17. HC TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC trCL VCC 90% GND tH(H) 3V 2.7V 1.3V 0.3V GND tH(H) tH(L) VCC DATA INPUT DATA INPUT 50% tH(L) 3V 1.3V 1.3V 1.3V GND tSU(H) tSU(H) tSU(L) tTLH 90% OUTPUT tTHL 90% 50% 10% tTLH 90% 1.3V OUTPUT tREM 3V SET, RESET OR PRESET GND tTHL 1.3V 10% FIGURE 19. HC SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS tPHL 1.3V GND IC CL 50pF GND 90% tPLH 50% IC tSU(L) tPHL tPLH tREM VCC SET, RESET OR PRESET tfCL CLOCK INPUT 50% 10% tPLH FIGURE 18. HCT TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC tfCL trCL tTLH 1.3V 10% tPLH tPHL GND tTHL 90% 50% 10% INVERTING OUTPUT 3V 2.7V 1.3V 0.3V INPUT tTHL CLOCK INPUT tf = 6ns tr = 6ns VCC CL 50pF FIGURE 20. HCT SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND PROPAGATION DELAY TIMES FOR EDGE TRIGGERED SEQUENTIAL LOGIC CIRCUITS 14 CD54HC4351, CD74HC4351, CD74HCT4351, CD74HC4352 Test Circuits and Waveforms 6ns (Continued) 6ns OUTPUT DISABLE tr VCC 90% 50% 10% OUTPUTS ENABLED OUTPUT HIGH TO OFF 50% OUTPUTS DISABLED FIGURE 21. HC THREE-STATE PROPAGATION DELAY WAVEFORM OTHER INPUTS TIED HIGH OR LOW OUTPUT DISABLE IC WITH THREESTATE OUTPUT GND 1.3V tPZH 90% OUTPUTS ENABLED OUTPUTS ENABLED 0.3 10% tPHZ tPZH 90% 3V tPZL tPLZ OUTPUT LOW TO OFF 50% OUTPUT HIGH TO OFF 6ns GND 10% tPHZ tf 2.7 1.3 tPZL tPLZ OUTPUT LOW TO OFF 6ns OUTPUT DISABLE 1.3V OUTPUTS DISABLED OUTPUTS ENABLED FIGURE 22. HCT THREE-STATE PROPAGATION DELAY WAVEFORM OUTPUT RL = 1kΩ CL 50pF VCC FOR tPLZ AND tPZL GND FOR tPHZ AND tPZH NOTE: Open drain waveforms tPLZ and tPZL are the same as those for three-state shown on the left. The test circuit is Output RL = 1kΩ to VCC, CL = 50pF. FIGURE 23. HC AND HCT THREE-STATE PROPAGATION DELAY TEST CIRCUIT 15 PACKAGE OPTION ADDENDUM www.ti.com 9-Oct-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type CD54HC4351F3A ACTIVE CDIP J 20 1 TBD A42 SNPB N / A for Pkg Type CD74HC4351E ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HC4351EE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HC4351M ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4351M96 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4351M96E4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4351M96G4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4351ME4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4351MG4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD74HC4352E ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HC4352EE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HCT4351E ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD74HCT4351EE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Package Drawing Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 9-Oct-2007 information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device CD74HC4351M96 Package Package Pins Type Drawing SOIC DW 20 SPQ Reel Reel Diameter Width (mm) W1 (mm) 2000 330.0 24.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 10.8 13.0 2.7 12.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CD74HC4351M96 SOIC DW 20 2000 346.0 346.0 41.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated