EGP20A-EGP20K High Efficiency Rectifiers VOLTAGE RANGE: 50 --- 800 V CURRENT: 2.0 A Features DO - 15 Low cost Diffused junction Low leakage Low forward voltage drop High current capability Easily cleaned with Alcohol,Isopropanol and similar solvents The plastic material carries U/L recognition 94V-0 Mechanical Data Case:JEDEC DO--15,molded plastic Terminals: Axial lead ,solderable per MIL- STD-750,Method 2026 Polarity: Color band denotes cathode Weight: 0.014 ounces,0.39 grams Mounting position: Any Dimensions in millimeters MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified. Single phase,half wave,60 Hz,resistive or inductive load. For capacitive load,derate by 20%. EGP EGP EGP EGP EGP EGP EGP EGP 20A 20B 20C 20D 20F 20G 20J 20K UNITS Maximum recurrent peak reverse voltage VRRM VRMS VDC Maximum RMS voltage Maximum DC blocking voltage Maximum average forw ard rectified current 9.5mm lead length, @TA =75 50 100 150 200 300 400 600 800 35 70 105 140 210 280 420 560 V V 50 100 150 200 300 400 600 800 V IF(AV) 2.0 A IFSM 75 A Peak forw ard surge current 8.3ms single half-sine-w ave superimposed on rated load @TJ =125 Maximum instantaneous forw ard voltage @ 2.0 A Maximum reverse current @TA =25 VF at rated DC blocking voltage @TA =125 Maximum reverse recovery (Note1) Typical junction capacitance (Note2) Typical thermal resistance Typical thermal resistance (Note3) (Note 4) Storage temperature range 1.7 5.0 100 IR trr CJ RθJA RθJL TJ TSTG Operating junction temperature range 1.25 0.95 Ａ 75 45 50 70 40 15 V ns pF ／Ｗ - 55 ---- + 150 - 55 ---- + 150 NOTE: 1. Measured with I F =0.5A, I R=1A, I rr=0.25A. 2. Measured at 1.0MHz and applied rev erse v oltage of 4.0V DC. 3.Thermal resistance f rom junction to ambient. 4.Thermal resistance from junction to lead. ht t p : // Revision:20170701-P1 www.lgesemi .c o m mail:[email protected] EGP20A-EGP20K High Efficiency Rectifiers Ratings AND Charactieristic Curves FIG.1 -- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC trr 10 N1. 50 N1. +0.5A D.U.T. (-) PULSE GENERATOR (NOTE2) (+) 25VDC (approx) (-) OSCILLOSCOPE (NOTE1) 1 NONINDUCTIVE 0 -0.25A (+) -1.0A 1cm NOTES:1.RISE TIME = 7ns MAX.INPUT IMPEDANCE = 1M .22pF. JJJJJ2.RISE TIME =10ns MAX.SOURCE IMPEDANCE=50 . SET TIME BASE FOR 20/30 ns/cm FIG.3 -- FORWARD DERATING CURVE z AVERAGE FORWARD CURRENT AMPERES 50 EGP20A-EGP20D 10 EGP20J-EGP20K AMPERES INSTANTANEOUS FORWARD CURRENT FIG.2 -- TYPICAL FORWARD CHARACTERISTIC 1 EGP20F-EGP20G 0.1 Pulse Width=300 µs 1% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.0 1.5 EGP20A-EGP20k 1 0.5 0.375"(9.5mm)LEAD LENGTH 0 0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 80 60 40 EGP20A-EGP20D EGP20F&EGP20K 0.1 1 4 10 100 1000 REVERSE VOLTAGE,VOLTS 75 100 125 150 175 105 T J =125 8.3ms Single Half Sine-Wave 90 75 60 EGP20A-EGP20K 45 30 15 0 10 1 100 NUMBER OF CYCLES AT 60Hz PACKAGE SPQ/PCS CARTON SPQ/PCS CARTON SIZE/CM CARTON GW/KG CARTON NW/KG DO-15 3000/AMMO 30000 42X28X31 12.00 10.00 ht t p : // Revision:20170701-P1 PEAK FORWARD SURGE CURRENT AMPERES JUNCTION CAPACITANCE,pF TJ=25 100 0 50 FIG.5 -- PEAK FORWARD SURGE CURRENT 140 20 25 AMBIENT TEMPERATURE, FIG.4 -- TYPICAL JUNCTION CAPACITANCE 120 Single Phase Half Wave 60Hz Resistive or Inductive Load www.lgesemi .c o m mail:[email protected]