7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER PART NUMBER 4 3 2 20 REVISION DESCRIPTION A 2151257 -2 DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 5 FINE CRIMP HEIGHT ADJUST A 2151257 -5 SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED PNEUMATIC SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 12 A NON-CRIMP HEIGHT ADJUST 2151257 -7 A FINE CRIMP HEIGHT ADJUST A PNEUMATIC FEED SERVO LATCH PLATE 2151257 -6 7- 2151257 -7 CONVERT TO MECHANICAL FINE CRIMP HEIGHT ADJUST A APPLICATOR STYLE CONVERSION CHART FEED TYPE 4 NONE CRIMP TOOLING KIT - 4 PNEUMATIC FEED - 2119950-1 1338685-1 2161326-1 - 2119951-1 - 2119949-1 1338685-1 2119951-1 - 2161326-1 - 2119949-1 1338685-1 2119950-1 5-18022-5 8- 2151257 -5 8- 2151257 -4 5-18022-5 8- 2151257 -5 8- 2151257 -4 5-18022-5 1338685-1 - 5-18022-5 - - 2119641-1 1901094-3 - 2119653-1 1901094-3 - 2119653-1 2119641-1 - 2119799-1 CRIMP WIRE INSUL SIZE 2-1752354-4 - 2-1752354-4 - 2168400-6 2168400-6 - 2119799-1 - (QUANTITY 2) (QUANTITY 2) - - - - - - - - - - - - - - 6 2063440-1 - - - - - - - - - - - - TYPE - F O 1.78 mm [.070] 3.84 mm [.151] APPLICATOR INSTRUCTIONS 408-10389 - - TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION WIRE STRIP LENGTH 4.90-5.50 mm [.193-.217 IN] C - JUNIOR POWER TIMER RECEPTACLE TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION n 114-15076 - - INSULATION DIAMETER RANGE - 1.25-2.05 mm [.049-.081 IN] - - - - - - - TERMINALS APPLIED TE TERMINAL 185026-1 185026-3 TE TERMINAL 185026-4 C1__DWG_PN_1_0 C1__DWG_PN_1_1 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE SEAL 828904-1 6 TE SEAL C1__DWG_PN_3_0 C1__DWG_PN_4_0 - C1__DWG_PN_3_1 - C1__DWG_PN_1_2 - WIRE SIZE 1.00mm2 0.75mm2 0.60mm2 0.50mm2 0.35mm2 B CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 W1__DWG_WGAUGE_5 1.50+/-0.05 [.059+/-.002] 1.40+/-0.05 [.055+/-.002] 1.32+/-0.05 [.052+/-.002] 1.27+/-0.05 [.050+/-.002] 1.21+/-0.05 [.048+/-.002] 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY CRIMP HEIGHT REFERENCE SETTING 4.1 W1__DWG_CRIMP_HT_1 5.2 W1__DWG_CRIMP_HT_2 6.1 W1__DWG_CRIMP_HT_3 6.7 W1__DWG_CRIMP_HT_4 7.1 W1__DWG_CRIMP_HT_5 - 9 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 - W1__FA_SETTING_4 - W1__FA_SETTING_5 *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. 6 7 APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 8 9 10 11 A 12 13 14 2151257 2151257 2151257 2151257 - -4 -4 -5 -6 - & 242. 1 & 242. & 252. 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. - - TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON THE BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. WHEN ASSEMBLING A NON CRIMP HEIGHT ADJUST APPLICATOR (-6) USE SHIMS FROM ITEM 260 TO ACHIEVE A NOMINAL SHIM HEIGHT OF THIS APPLICATOR APPLIES TERMINAL WITH A SEAL. APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. AMP 4805 REV 31MAR2000 - - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62, 180 FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 37, 180 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 - - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 - - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 REVISIONS DIST A 66 P LTR - 1 1 1 -77 -7 1 - -6 1 1 1 -5 1 1 1 1 1 1 -2 1 2119957-2 8-21084-0 2119640-1 2079988-1 2119641-1 2119798-1 1-22279-3 -1 PART NO 1 1 DESCRIPTION DATE DWN APVD 1 ORIGINAL 02APR2013 GH TE A RELEASED 14MAY2013 GH TE 2063440-1 - APPLICATOR DATA 1 PART NUMBERS REQUIRED - LOC SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. 2151257 -1 D 6 APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DETENT PIN SPRING, COMPRESSION DESCRIPTION 1 2119957-2 1 8-21084-0_GATD 1 2119640-1 1 2079988_GATD 1 2119641-1 1 2119798-1 1 1-22279-3_SIMP 260 252 250 249 248 247 246 ITEM NO 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 1 REF 1 1 1 1 1 2 1 3 1 1 4 1 1 - - 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 - 1 1 1 1 1 1 ATLANTIC VERSION mm MATERIAL - -1 PART NO 1 2 1 1 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 - - 1 1 1 1 1 1 - - - 1 1 - - - 1 1 2 - 1 1 1 2 1 1 1 2119758-1 2119082-7 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 2-1752354-4 993111-1 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-3 2119956-1 2119791-9 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 985575-3 1338685-1 2168400-1 1-5018030-0 1901681-1 18023-9 2119652-1 2119653-1 2119656-9 2119370-1 2079383-7 2119645-1 2119957-1 2119644-1 2119085-1 2119092-1 1-1752356-7 2079383-5 2161328-1 1-1320908-2 2119959-2 1-455888-0 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1-1633919-0 2119781-5 2-238011-1 3-1633965-1 455888-2 3-456404-1 - - 1 1 REF REF REF REF - - - 1 - - 1 - 1 1 1 1 1 1 -6 1 1 1 1 - 1 1 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 - 1 1 2 - - - 1 1 - 1 1 1 - - 4 1 1 - 1 4 1 - 1 1 4 1 1 1 - 1 1 1 1 4 3 1 - - 1 3 1 1 2 1 3 - 1 2 1 1 1 1 2 - 1 1 - - 1 1 1 2 - 1 1 - 1 - 1 1 - 1 REF REF 1 - - 1 1 - - 1 1 - 1 REF REF 1 - 1 1 -5 -2 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: & 4 of 4) 1 -77 -7 4.30 . Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 - - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - RAM, AMP STYLE, SIDE FEED, NON-ADJ. CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM DWN 02APR2013 CHK 02APR2013 APVD 02PAR2013 HOFFNER T.ELBIN T.ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 1 2-1752354-4 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-3 1 2119956-1 1 2119791-9 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 2079383-4 1 5-18022-5 1 985575-3 1 1338685-1 4 2168400-1 1 1-5018030-0 1 1901681-1 3 18023-9 1 2119652 1 2119653 1 2119656-9 1 2119370 1 2079383-7 1 2119645 1 2119957-1 1 2119644-1 1 2119085 1 2119092-1 1 1-1752356-7 2 2079383-5 1 2161328 1 1-1320908-2 1 2119959-2 1 1-455888-0 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1-1633919-0 .. 1 ITEM_7 .. 1 ITEM_6 1 2119781-5 1 2-238011-1 1 3-1633965-1 1 455888-2 1 3-456404-1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079764 245 244 243 242 241 240 239 238 213 198 180 177 176 175 174 172 166 164 163 137 136 135 133 119 117 82 71 70 67 66 63 62 60 59 57 56 54 52 51 49 48 47 46 44 41 40 39 38 37 35 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119082-7 DESCRIPTION PRODUCT SPEC - 1 2119758 Ocean Side Feed Applicator - DRAWING NO 2151257 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE MECHANICAL 6 A DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 D 6 59 56 39 247 246 245 2 7 63 A 44 7 252 249 35 166 242 1.27 [ 0.050 ] 2 57 REF 2 SHEAR DEPRESSOR DETAIL 2 6 163 8 82 1 1 70 3 C 1 177 56 SERVO LATCH PLATE 4 2 176 2 TERMINAL SUPPORT LOCATION 28 5 41 174 44 135 2 175 51 6 164 A 15.01 [ 0.591 ] 66 180 2 67 11 57 213 33 24 SERVO FEEDER NOT INCLUDED 117 REF 10 A 19 30 20 29 21 B 1 ITEM 30 LOCATED AT FRONT HOLES 12 241 CAM POSITIONS 13 30 REF 29 REF 1 11 11 30mm STROKE 30mm STROKE 119 46 32 34 54 8 1 60 54 10 1 FEED TRACK POSITION GUIDE BY INSULATION BARREL 248 48 50 REF HOLDDOWN SET-UP 9 47 REF 245 REF 52 198 30mm STROKE 1.00 0.50 [ 0.039 0.019 ] 34 REF 172 4 REF 2 137 B 2 8 136 133 D 2 243 59 240 - REF 5 244 238 C - 62 260 PNEUMATIC APVD 37 38 250 DWN - 40 239 DATE A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 02APR2013 CHK 02APR2013 APVD 02PAR2013 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151257 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER PART NUMBER 4 3 2 20 REVISION DESCRIPTION A 2- 2151257 -2 DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 5 SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. 2- 2151257 -1 D 6 FEED TYPE FINE CRIMP HEIGHT ADJUST A FINE CRIMP HEIGHT ADJUST PNEUMATIC FEED SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED PNEUMATIC 2- 2151257 -5 A FINE CRIMP HEIGHT ADJUST 2- 2151257 -7 A FINE CRIMP HEIGHT ADJUST NONE A CONVERT TO MECHANICAL SERVO LATCH PLATE 7- 2151257 -7 APPLICATOR STYLE CONVERSION CHART CRIMP TOOLING KIT - SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED 4 PNEUMATIC FEED - - CRIMP WIRE INSUL SIZE 2119950-1 1338685-1 2161326-1 - 2119951-1 - 2119949-1 8- 2151257 -4 1338685-1 2119950-1 5-18022-5 1338685-1 - 5-18022-5 - - - 8- 2151257 -5 - 2119949-1 8- 2151257 -4 5-18022-5 - 2161326-1 2119641-2 8- 2151257 -5 1338685-1 2119951-1 5-18022-5 - - - 1901094-3 2119653-2 1901094-3 - 2119653-2 2119641-2 - 2119799-1 2-1752354-4 - - 2-1752354-4 - 2168400-6 (QUANTITY 2) 2119799-1 - - 6 - 2168400-6 - - - - (QUANTITY 2) - - - - - 2063440-1 - - - - - - - TYPE APPLICATOR INSTRUCTIONS 408-10389 - - - - - TE TERMINAL TERMINAL DATA: TE CRIMP SPECIFICATION WIRE STRIP LENGTH 4.90-5.50 mm [.193-.217 IN] C - JUNIOR POWER TIMER RECEPTACLE TERMINAL NAME: TERMINAL APPLICATION SPECIFICATION n 114-15076 - - INSULATION DIAMETER RANGE - 1.25-2.05 mm [.049-.081 IN] - - - - - TERMINALS APPLIED TE TERMINAL 185026-1 185026-3 TE TERMINAL C1__DWG_PN_1_0 185026-4 C1__DWG_PN_1_1 C1__DWG_PN_2_0 C1__DWG_PN_2_1 TE SEAL C1__DWG_PN_3_0 828904-1 TE SEAL - C1__DWG_PN_4_0 - C1__DWG_PN_3_1 - C1__DWG_PN_1_2 - WIRE SIZE 1.00mm2 0.75mm2 0.60mm2 0.50mm2 0.35mm2 1 B 2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 W1__DWG_WGAUGE_3 W1__DWG_WGAUGE_4 W1__DWG_WGAUGE_5 1.50+/-0.05 [.059+/-.002] 1.40+/-0.05 [.055+/-.002] 1.32+/-0.05 [.052+/-.002] 1.27+/-0.05 [.050+/-.002] 1.21+/-0.05 [.048+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 W1__DWG_CRIMP_HT_3 W1__DWG_CRIMP_HT_4 W1__DWG_CRIMP_HT_5 4.1 5.2 6.1 6.7 7.1 - 9 - 6 W1__FA_SETTING_1 - W1__FA_SETTING_2 - W1__FA_SETTING_3 W1__FA_SETTING_4 - W1__FA_SETTING_5 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. RECOMMENDED SPARE PARTS - GREASE BEARING SURFACES LIGHTLY - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 - APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- - 2151257 -4 2151257 -4 2151257 -5 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62, 180 7 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 8 9 10 11 A 12 13 - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. THIS APPLICATOR APPLIES TERMINAL WITH A SEAL. APPLY TORQ-SEAL IN ALLEN SOCKET TO FILL HOLE AFTER FLAT HD HAS BEEN ADJUSTED TO CORRECT HEIGHT AT QUALIFICATION. APPLY #1-23419-5 LOC-TITE TO THREADS. - 1 & 152. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - & 242. - 1 MAGNET MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. AMP 4805 REV 31MAR2000 - 1 6 66 P LTR DESCRIPTION DATE SEE SHEET 1 DWN APVD - - - 2063440-1 - 3.84 mm [.151] A PART NUMBERS REQUIRED F O 1.78 mm [.070] REVISIONS DIST - - APPLICATOR DATA LOC 1 1 1 - - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -77 -27 -25 -22 -21 2119782-1 2119640-1 2079988-1 1-22279-3 2119082-7 PART NO FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT DESCRIPTION 1 2119782 1 2119640-1 1 2079988_GATD 1 1-22279-3_SIMP 1 2119082-7 - 251 250 249 246 244 1 1 1 - 1 1 1 1 1 1 - 1 2 1 REF 1 1 - 1 1 1 1 - 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 - - 1 1 1 1 1 - - - - - 1 - - - 1 1 2 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 2-1752354-4 993111-1 8-22280-7 1752353-2 1901680-2 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 1-2119656-0 2119650-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-3 2119956-1 2119791-9 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 985575-3 1338685-1 1-5018030-0 1901681-1 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 2119644-1 1-1752356-7 2079383-5 2161328-1 1-1320908-2 2119959-2 1-455888-0 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 1-1633919-0 2119781-5 2-238011-1 3-1633965-1 455888-2 3-456404-1 1 - 1 1 REF REF REF - - 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 - 1 1 1 1 - 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 - 1 3 1 1 - 1 3 - 1 2 1 3 - 1 2 1 3 1 1 2 1 1 1 - 2 1 1 1 1 - 1 1 1 1 - 1 1 - 1 REF 1 - - 1 - - - 1 1 - 1 REF - 1 1 - - 1 1 - - 1 1 1 - 1 1 1 1 4 - 1 1 1 4 - 1 1 1 4 - - 1 1 4 1 1 1 1 - 1 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: mm & 2 of 4) 1 MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER STANDOFF,HOLD-DOWN PIN, SLOTTED SPRING 3.0 X 20.0 SPRING, COMPRESSION GUIDE PIN,HOLDDOWN GUIDE PIN,HOLDDOWN RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER DOCUMENTATION PACKAGE DEPRESSOR, WIRE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 SCR, FLT SKT HD CAP M3 X 10.0 PAWL, FEED NUT, HEX, REG, RoHS, M3.5 HOLDDOWN, TERMINAL SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION O PREMIUM SPACER, CRIMPER CRIMPER, WIRE PREMIUM PART NO -77 -27 -25 -22 -21 ITEM NO PACIFIC VERSION Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 1 1 DWN 02APR2013 CHK 02APR2013 APVD 02PAR2013 HOFFNER T.ELBIN T.ELBIN NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 1 2-1752354-4 1 993111-1 1 8-22280-7_SIMP 1 1752353-2 1 1901680-2 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 4 2168400-5 1 2119653-2 1 1-2119656-0 1 2119650 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-3 1 2119956-1 1 2119791-9 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 5-18022-5 1 985575-3 1 1338685-1 1 1-5018030-0 1 1901681-1 3 18023-9 1 2119652 1 2079383-7 1 2119645 1 2119957-1 1 2119644-1 1 1-1752356-7 2 2079383-5 1 2161328 1 1-1320908-2 1 2119959-2 1 1-455888-0 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 1-1633919-0 .. 1 ITEM_7 .. 1 ITEM_6 1 2119781-5 1 2-238011-1 1 3-1633965-1 1 455888-2 1 3-456404-1 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 7-18023-7 243 242 241 240 239 238 213 198 180 177 176 175 174 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 119 117 82 71 70 67 66 63 62 59 57 56 52 51 49 48 41 40 39 38 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119083 DESCRIPTION PRODUCT SPEC - 1 2079764 Ocean Side Feed Applicator - DRAWING NO 2151257 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 1 REVISIONS DIST 66 P LTR DESCRIPTION SEE SHEET 1 - FEED TYPE DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 APVD - - - 62 6 40 A 145 38 239 246 39 59 7 56 140 152 2 REF 5 2 D 1.27 [ 0.050 ] 2 57 244 7 139 REF SHEAR DEPRESSOR DETAIL 243 PNEUMATIC 250 2 8 249 A 166 242 2 6 1.00 0.50 [ 0.039 0.019 ] 63 238 REF 8 163 34 59 82 136 1 137 C 172 177 56 176 2 SERVO LATCH PLATE 2 1 133 4 135 2 REF TERMINAL SUPPORT LOCATION 2 70 3 C 1 4 28 174 5 41 52 240 140 REF 175 51 198 164 66 6 180 67 33 SERVO FEEDER NOT INCLUDED 213 A 24 50 19 10 30 15.01 [ 0.591 ] 57 2 11 A B DWN 251 MECHANICAL D DATE REF HOLDDOWN SET-UP 20 117 REF 9 21 29 B 1 12 241 13 1 ITEM 30 LOCATED AT FRONT HOLES 11 30 CAM POSITIONS 30mm STROKE REF 29 30mm STROKE 30mm STROKE 142 REF 151 141 32 34 143 8 1 144 143 10 1 119 11 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 02APR2013 CHK 02APR2013 APVD 02PAR2013 HOFFNER T.ELBIN T.ELBIN TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151257 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A