CHEMI-CON EMZR500ADA101MF80G Surface mount aluminum electrolytic capacitor Datasheet

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
TM
AIchip
MZR
-
Series
・Downsizing and Lower ESR, 2,000hours at 105℃
・Rated voltage range : 6.3 to 50V, Nominal capacitance range : 100 to 2,200μF
・Solvent resistant type(see PRECAUTIONS AND GUIDELINES)
・Vibration resistance structure
・RoHS Compliant
・AEC-Q200 compliant : Please contact Chemi-Con for more details, test data, information.
Low ESR, 105℃
MZR
Downsized
MZJ P98
◆SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
Surge Voltage Test
Characteristics
-55 to +105℃
6.3 to 50Vdc
(at 20℃, 120Hz)
±20% (M)
I=0.01CV or 3μA, whichever is greater.
Where, I : Max. leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V)
(at 20℃ after 2 minutes)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V
(at 20℃, 120Hz)
tanδ(Max.)
0.26 0.19 0.16 0.14 0.12 0.10
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V
(at 120Hz)
Z(-25℃)/Z(+20℃)
2
2
2
2
2
2
Z(-40℃)/Z(+20℃)
3
3
3
3
3
3
Z(-55℃)/Z(+20℃)
4
4
4
3
3
3
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours
at 105℃.
Capacitance change
≦±30% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
≦±30% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specified surge voltage for 30±5 seconds through
a protective resistor (as required for RC=0.1±0.05sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35℃.
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V
7.2V 12V 18V 29V 40V 58V
Surge voltage (Vdc)
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦200% of the initial specified value
Leakage current
≦The initial specified value
(Caution)
Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specific conditions.It does
not imply long-term use at all.
◆DIMENSIONS [mm]
● Terminal
● Terminal
● Size
● Size
B±0.2
φD±0.5
P
C±0.2
0.3max.
L±0.3 (Note)
D
6.3
8
10
C
B
A
L
7.7 6.6 6.6 7.2
10.0 8.3 8.3 9.0
10.0 10.3 10.3 11.0
W
0.5 to 0.8
0.7 to 1.1
0.7 to 1.1
P
1.9
3.1
4.5
A±0.2
L±0.5
A±0.2
F80
HA0
JA0
W
0.3max.
Vent for JA0
W
B±0.2
φD±0.5
Vent for JA0
Code : G(Vibration resistant structure)
code : HA0 and JA0
Size code
P
C±0.2
Code : A
code : F80 to JA0
Note : L±0.5 for HA0 and JA0
: Dummy terminals
◆MARKING
EX) 35V330µF
3Q
330
VZR
● Rated
voltage symbol
Rated voltage (Vdc)
Symbol
6.3
j
10
A
16
C
25
E
35
V
50
H
Applying voltage over the rated voltages causes the capacitors to have short lifetime.
Besides, applying voltage over the specified surge voltages may cause to have short circuit failure. A protection
circuit should be used if applied voltage will exceed the rated voltages.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
96
CAT. No. E1001Q
SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
MZRSeries
TM
AIchip
Low ESR, 105℃
-
◆PART NUMBERING SYSTEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
E MZ R AAA A DA AAA M AAA G
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 220µF:221, 470µF:471)
Taping code
Terminal code (A, G)
Voltage code (ex. 6.3V:6R3, 10V:100, 35V:350)
Series code
Category
Please refer to "Product code guide (surface mount type)"
◆STANDARD RATINGS
WV
(Vdc)
Cap
(µF)
680
1,500
2,200
470
1,000
1,500
330
680
1,000
220
470
820
150
330
560
100
220
330
6.3
10
16
25
35
50
Size code
tanδ
ESR
(Ω max./20℃, 100kHz)
Rated ripple current
(mArms/105℃, 100kHz)
Part No.
F80
HA0
JA0
F80
HA0
JA0
F80
HA0
JA0
F80
HA0
JA0
F80
HA0
JA0
F80
HA0
JA0
0.26
0.26
0.26
0.19
0.19
0.19
0.16
0.16
0.16
0.14
0.14
0.14
0.12
0.12
0.12
0.10
0.10
0.10
0.16
0.08
0.06
0.16
0.08
0.06
0.16
0.08
0.06
0.16
0.08
0.06
0.16
0.08
0.06
0.34
0.18
0.12
600
850
1,190
600
850
1,190
600
850
1,190
600
850
1,190
600
850
1,190
350
670
900
EMZR6R3ADA681MF80G
EMZR6R3□DA152MHA0G
EMZR6R3□DA222MJA0G
EMZR100ADA471MF80G
EMZR100□DA102MHA0G
EMZR100□DA152MJA0G
EMZR160ADA331MF80G
EMZR160□DA681MHA0G
EMZR160□DA102MJA0G
EMZR250ADA221MF80G
EMZR250□DA471MHA0G
EMZR250□DA821MJA0G
EMZR350ADA151MF80G
EMZR350□DA331MHA0G
EMZR350□DA561MJA0G
EMZR500ADA101MF80G
EMZR500□DA221MHA0G
EMZR500□DA331MJA0G
□ : Enter the appropriate terminal code.
◆RATED RIPPLE CURRENT MULTIPLIERS
・Frequency Multipliers
Capacitance(µF)
Frequency(Hz)
100 to 150
220 to 560
680 to 2,200
120
0.40
0.50
0.60
1k
0.75
0.85
0.87
10k
0.90
0.94
0.95
100k
1.00
1.00
1.00
The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5℃ rise.
When long life performance is required in actual use, the rms ripple current has to be reduced.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
97
CAT. No. E1001Q
Similar pages