P-DUKE DOH16-12T Non-isolated point of load dc/dc converter Datasheet

FEATURES
• OUTPUT CURRENT UP TO 16A
• SMALL SIZE AND LOW PROFILE :
1.30” X 0.53” X 0.30” (SMD) ; 2.00” X 0.50” X 0.28” (SIP)
• HIGH EFFICIENCY - 92% @ 3.3V FULL LOAD
• INPUT RANGE FROM 8.3VDC TO 14.0VDC
• FIXED SWITCHING FREQUENCY (300KHZ)
• SMD & SIP PACKAGES
• OUTPUT VOLTAGE PROGRAMMABLE FROM 0.75VDC TO 5.0VDC
VIA EXTERNAL RESISTOR
• INPUT UNDER-VOLTAGE LOCKOUT
• UL60950-1, EN60950-1 AND IEC60950-1 LICENSED
• ISO9001 CERTIFIED MANUFACTURING FACILITIES
• COMPLIANT TO RoHS EU DIRECTIVE 2002/95/EC
APPLICATIONS
Wireless Network
Telecom/Datacom
Industry Control System
Distributed Power Architectures
Semiconductor Equipment
Microprocessor Power Applications
OPTIONS
Positive Logic Remote on/off
DESCRIPTION
DOS16-12T (SMD type), DOH16-12T (for Vertical Mounting SIP type) and
DOH16-12TA (for Horizontal Mounting SIP type) are non-isolated DC/DC
converters that can deliver up to 16A of output current with full load efficiency of
92% at 3.3V output.
T E C H N I C A L S P E C I F I C AT I O N
All specifications are typical at nominal input, full load and 25ºC otherwise noted
OUTPUT SPECIFICATIONS
Output current
Voltage accuracy
INPUT SPECIFICATIONS
Full load and Vin(nom)
Minimum load
16A max
± 2%Vo(set)
0%
Vin=Vin(min) to Vin(max)
at Full Load
No Load to Full Load
Line regulation
Load regulation
Ripple and noise (Note2) 20MHz bandwidth
± 0.3%Vo(set),typ
± 0.4%Vo(set),typ
30mVrms,max
75mVp-p,max
±0.4%, typ
Temperature coefficient
ΔIo /Δt = 2.5A/μS ,Vin(nom) Peak deviation 200mV,typ
Dynamic load
Load change step
Setting time
response
(50%
to
100%
or
(Vo<10%peak
25μS,typ
(Note 2)
100% to 50% of Io(max))
deviation)
ΔIo /Δt = 2.5A/μS ,Vin(nom) Peak deviation 100mV,typ
Dynamic load
Load change step
Setting time
response
(50%
to
100%
or
(Vo<10%peak
50μS,typ
(Note 3)
100% to 50% of Io(max))
deviation)
Output current limit
180%
Output short-circuit current
Hiccup, automatics recovery
ESR≧1mΩ
1000μF,max
External load capacitance
5000μF,max
ESR≧10mΩ
Vin=Vin(min) to Vin(max)
Output voltage overshoot-startup
1%Vo(set)
F.L.
Voltage adjustability (see fig.1)
(Note 4)
0.7525V ~ 5.0V
GENERAL SPECIFICATIONS
Efficiency
Isolation voltage
Switching frequency
Approvals and standard
SMD
Dimensions
SIP
See table
None
300KHz, typ
IEC60950-1, UL60950-1, EN60950-1
1.30 X 0.53 X 0.30 Inch
(33.0 X 13.5 X 7.7 mm)
2.00 X 0.50 X 0.28 Inch
(50.8 X 12.7 X 7.2 mm)
Weight
MTBF (Note 1)
BELLCORE TR-NWT-000332
MIL-HDBK-217F
Vo(set) ≦3.63V
Vin(nom) =12V
Vo(set) >3.63V
Input voltage range
Maximum input current
8.3 – 14VDC
8.3 – 13.2VDC
Vin=8.3 to 14.0Vdc; Io=Io(max)
10A
Input filter (Note 5)
C filter
Input no load current
(Vin=12V, Io=0, module enabled)
Input under voltage lockout
Input reflected ripple current
Vo(set) =0.75Vdc
Vo(set) =5.0Vdc
Start-up voltage
Shutdown voltage
40mA,typ
100mA,typ
7.9V,typ
7.8V,typ
5~20MHz, 1μH source impedance
30mAp-p
ENVIRONMENTAL SPECIFICATIONS
Operating ambient temperature
–40ºC ~ +85ºC(with derating)
Storage temperature range
–55ºC ~ +125ºC
Thermal shock
MIL-STD-810F
Over temperature protection
125ºC,typ
FEATURE SPECIFICATIONS
Remote ON/OFF(Note 6)
Negative logic(standard)
ON = 0V < Vr < 0.3V
OFF =2.5V < Vr < Vin(max)
Positive logic(option)
ON = (Vin-4) < Vr < Vin(max)
OFF=0V < Vr < 0.3V
Input current of Remote control pin
Remote off state input current Nominal Vin
Remote sense range
Rise time
0.5V,max
Time for Vo to rise from 10% to 90%of Vo(set)
Turn-on delay time
IIN=10μA,max
IIN=1mA,max
IIN=10μA,max
IIN=1mA,max
10μA~1.0mA
2.0mA,typ
Case 1 (Note 7)
Case 2 (Note 8)
6ms,max.
3ms,typ
3ms,typ
6.0g(0.22oz)
7
1.409 x 10 hrs
5
6.704 x 10 hrs
Page 1 of 3
Issued Date:2007/10/12
Model Name
ON/OFF
Logic
DOS16-12T
DOS16-12T-P
DOH16-12T
DOH16-12T-P
DOH16-12TA
DOH16-12TA-P
Negative
Positive
Negative
Positive
Negative
Positive
Package
Input Voltage
SMD
Vo(set)≦3.63V
Vin = 8.3-14Vdc
Vertical Mounting
SIP
Horizontal Mounting
SIP
Output Voltage
0.75 ~ 5.0Vdc
Output Current
Efficiency (%)
Min. Load
Max. Load
12Vin, 3.3Vdc@16A
0A
16A
92%
Vo(set)>3.63V
Vin = 8.3-13.2Vdc
Note
1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC.
MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment).
2. External with Cout = 1μF ceramic//10μF tantalum capacitors.
3. External with Cout = 2×150μF polymer capacitors.
4. Output voltage programmable from 0.7525V to 5V by connecting a single resistor (shown as Rtrim in Table 1) between the TRIM and GND pins of the
module.To calculate the value of the resistor Rtrim for a particular output voltage Vo, use the following equation:
Rtrim =
10500
[
Vo – 0.7525
-1000
]Ω
5.
It’s necessary to equip the external input capacitors at the input of the module. The capacitors should connect as close as possible to the input
terminals that ensuring module stability. The external Cin is 6×47μF ceramic capacitors at least.
6. Device code with suffix “-P” – Positive logic(On/Off is open collector/drain logic input; Signal referenced to GND )
Device code with no suffix – Negative logic (On/Off pin is open collector/drain logic input with external pull –up resistor; signal referenced to GND)
7. Case 1 :On/Off input is set to logic low (module on) and then input power is applied (delay from instant at which Vin=Vin(min) until Vo=10% of Vo(set))
8. Case 2 :Input power is applied for at least one second and then the On/Off input is set to logic low (delay form instant at which Von/off=0.3V until
Vo=10% of Vo(set))
CAUTION: This power module is not internally fused. An input line fuse must always be used.
DOS16-12T, Vo=3.3V, Derating Curve
OUTPUT CURRENT,Io(A)
18
16
14
12
10
8
6
4
2
0
20
30
40
50
60
70
80
Fig. 1
90
AMBIENT TEMPERATURE,TA(℃)
Table 1
Vo(set) (V)
Rtrim (KΩ)
0.7525
Open
1.2
22.46
1.5
13.05
1.8
9.024
2.5
5.009
3.3
3.122
5
1.472
Page 2 of 3
Issued Date:2007/10/12
DOH16-12T
VOUT
VOUT
+SENSE
GND
VOUT
GND
VIN
VIN
TRIM
ON/OFF
SIDE VIEW
BOTTOM VIEW
DOH16-12TA
VOUT
VOUT
+SENSE
GND
VOUT
GND
VIN
VIN
TRIM
ON/OFF
SIDE VIEW
BOTTOM VIEW
DOS16-12T
BOTTOM VIEW
SIDE VIEW
1. All dimensions in Inches (mm)
Tolerance: X.XX±0.02 (X.X±0.5)
X.XXX±0.01 (X.XX±0.25)
2. Pin pitch tolerance ±0.01(0.25)
3. Pin dimension tolerance ±0.004 (0.1)
Page 3 of 3
Issued Date:2007/10/12
Similar pages