Advanced Monolithic Systems AMSOP-07 LOW OFFSET VOLTAGE OPERATIONAL AMPLIFIER FEATURES APPLICATIONS • Low VOS………………………………………. 75µ µ V Max • Low VOS Drift.……………………………. 1.3µ µ V/°°C Max • Ultra Stable with Time……………… 1.5µ µ V/Month Max • Low Noise …………………………………..0.6µ µ VP-P Max • Wide Input Voltage Range ……………………..… ± 14V • Wide Supply Voltage Range ……………… ± 3V to ± 18V • High-Gain Instrumentation • Precision Data Acquisition • Precision Integrators • Precision Threshold Detectors • Biomedical Amplifiers GENERAL DESCRIPTION The AMSOP-07 is a precision operational amplifier with a very low input offset voltage. This device features a wide input voltage range of ±13V minimum, low input bias current, high impedance, high CMRR, excellent stability of offsets and gain over time and temperature. Excellent linearity can be maintained even at high closed-loop gains. Low cost, low noise, low offsets and high open-loop gain make the AMSOP-07 an excellent choice particularly for high-gain instrumentation applications. Other applications include precision data acquisition, precision integrators, threshold detectors and medical instrumentation. The AMSOP-07 is operational in the full industrial temperature range of -40°C to 85°C and is available in the 8 lead SOIC and plastic dip (PDIP) packages. ORDERING INFORMATION: TOL. PACKAGE TYPE 8 LEAD SOIC ±75µV AMSOP-07ES ±150µV AMSOP-07CS ±150µV AMSOP-07DS 8 LEAD PDIP AMSOP-07EP AMSOP-07CP AMSOP-07DP OPERATING TEMPERATURE RANGE -40 to 85° C -40 to 85° C -40 to 85° C PIN CONNECTIONS 8 Lead SOIC/ 8Lead PDIP VOS TRIM 1 8 VOS TRIM -IN 2 7 V+ +IN 3 6 OUT V- 4 5 N/C Top View Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMSOP-07 ABSOLUTE MAXIMUM RATINGS (Note1) Supply Voltage Differential Input Voltage Input Voltage Output Short Circuit Duration Operating Temperature Range ±22V ±30V ±22V Indefinite -40°C to 85°C Storage temperature Junction Temperature Soldering information (60 sec) Thermal Resistance 8 L SOIC 8 L PDIP -65°C to +125°C +150°C 300°C 158°C/W 103°C/W ELECTRICAL CHARACTERISTICS Electrical Characteristics at VIN =±15V and TA = +25°C unless otherwise specified. Parameter Conditions AMSOP-07E AMSOP-07 C Min Typ Max Min Typ Max AMSOP-07 D Min Typ Max Units Input Offset Voltage (Note 2) 30 75 60 150 60 150 µV Long Term VOS Stability (Note 3) 0.3 1.5 0.4 2.0 0.5 3.0 µV/Mo 0.5 3.8 0.8 6.0 0.8 6.0 nA ± 1.2 ± 4.0 ± 1.8 ± 7.0 ± 2.0 ± 12 nA Input Offset Current Input Bias Current Input Noise Voltage 0.1Hz to 10Hz 0.35 0.6 0.38 0.65 0.38 0.65 µVP-P Input Noise Voltage Density fO = 10Hz fO = 100Hz (Note 4) fO = 1000Hz 10.3 10.0 9.6 18.0 13.0 11.0 10.5 10.2 9.8 20.0 13.5 11.5 10.5 10.3 9.8 20.0 13.5 11.5 nV/√Hz Input Noise Current 0.1Hz to 10Hz 14 30 15 35 15 35 pAP-P Input Noise CurrentDensity fO = 10Hz fO = 100Hz (Note 4) fO = 1000Hz 0.32 0.14 0.12 0.80 0.23 0.17 0.35 0.15 0.13 0.90 0.27 0.18 0.35 0.15 0.13 0.90 0.27 0.18 pA/√Hz Input Resistance Differential-Mode (Note 5) 15 Input Resistance Common-Mode 50 8 160 Input Voltage Range Common-Mode Rejection Ratio VCM = ± 13 Power Supply Rejection Ratio VS = ± 13 to ± 18 Large-Signal Voltage Gain RL≥2kΩ, VO =± 10V RL≥500Ω, VO =± 0.5V, VS =± 0.5V (Note 5) Output Voltage Swing RL ≥10kΩ RL ≥2kΩ RL ≥1kΩ Slew Rate 33 7 120 MΩ 120 GΩ ± 13 ± 14 ± 13 ± 14 ± 13 ± 14 V 106 123 100 120 94 110 dB 5 20 7 32 7 200 150 500 400 120 100 400 400 120 ± 12.5 ± 12.0 ± 10.5 ± 13.0 ± 12.8 ± 12.0 ± 12.0 ± 11.5 ± 13.0 ± 12.8 ± 12.0 ± 12.0 RL ≥2kΩ (Note 4) 0.1 0.3 0.1 Closed-Loop Bandwidth AVCL =+1 (Note 6) 0.4 0.6 0.4 Open-Loop Output Resistance VO = 0, IO= 0 60 Power Consumption VS =± 15V, No Load VS =± 3V, No Load 75 4 Offset Adjustment Range RP =20kΩ ±4 Advanced Monolithic Systems, Inc. 31 µV/V 400 400 V/mV ± 11.5 ± 13.0 ± 12.8 ± 12.0 V 0.3 0.1 0.3 V/µs 0.6 0.4 0.6 MHz 60 Ω 60 120 6 32 80 4 ±4 150 8 80 4 ±4 150 8 mW mV 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMSOP-07 ELECTRICAL CHARACTERISTICS Electrical Characteristics at VIN= ±15, at -40°C ≤ TA ≤ +85°C unless otherwise specified. Parameter Conditions AMSOP-07E AMSOP-07 C Min Typ Max Min Typ Max AMSOP-07 D Min Typ Max Units Input Offset Voltage (Note 2) 45 130 85 250 85 250 µV Average Input Offset Voltage Drift (Note 5) Without External Trim 0.3 1.3 0.5 1.8 0.7 2.5 µV/°C With External Trim RP =2kΩ 0.3 1.3 0.4 1.6 0.7 2.5 µV/°C 0.9 5.3 1.6 8.0 1.6 8.0 nA 8 35 12 50 12 50 pA/°C ± 1.5 ± 5.5 ± 2.2 ± 9.0 ± 3.0 ± 14 nA 13 35 18 50 18 50 pA/°C Input Offset Current Average Input Offset Current Drift (Note 4) Input Bias Current Average Input Bias Current Drift (Note 4) Input Voltage Range Common-Mode Rejection Ratio VCM = ± 13 Power Supply Rejection Ratio VS = ± 13 to ± 18 Large-Signal Voltage Gain RL≥2kΩ, VO =± 10V Output Voltage Swing RL ≥2kΩ ± 13 ± 13.5 ± 13 ± 13.5 ± 13 ± 13.5 V 103 123 97 120 94 106 dB 7 32 10 51 10 180 450 100 400 100 400 ± 12.0 ± 13.0 ± 12.0 ± 13.0 ± 12.0 ± 13.0 µV/V 51 V/mV V Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Note 2: Input Offset Voltage measurements are performed by automated test equipment approximately 0.5 seconds after application of power. Note 3: Long-Term Input Offset Voltage Stability refers to the averaged trend line of VOS vs. Time over extended periods after the first 30 days of operation. Excluding the initial hour of operation, changes in VOS during the first 30 operating days are typically 2.5µV. Parameter is sample tested. Note 4: Sample tested Note 5: Guaranteed by design. Note 6: Guaranteed but not tested. TYPICAL PERFORMANCE CHARACTERISTICS 25 VS = ±15V 800 600 400 200 -50 0 50 TEMPERATURE (° C) Advanced Monolithic Systems, Inc. 100 20 30 TA = 25° C VS = ±15V 15 OP-07C 10 5 0 OP-07E 0 1 2 3 4 5 TIME AFTER POWER SUPPLY TURN-ON (minutes) NONINVERTING INPUT BIAS CURRENT (mA) ABSOLUTE CHANGE IN INPUT OFFSET VOLTAGE (µV) OPEN-LOOP GAIN (V/mV) 1000 0 Input Bias Current vs Differrential Input Voltage Warm-UpDrift AT | VDIFF | ≤ 1.0V, | IB | ≤ 7nA (OP-07C) -30 20 -20 10 -10 0 0 -10 -20 10 VS = ±15V TA = 25° C 20 -30 30 -30 -20 -10 0 10 20 30 DIFFERENTIAL INPUT VALUE (V) 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 INVERTING INPUT BIAS Open-Loop Gain vs Temperature AMSOP-07 TYPICAL PERFORMANCE CHARACTERISTICS (Continued) 2.5 3 2 OP-07C OP-07E 1 0 -50 1000 2.0 1.5 1.0 OP-07C 0.5 OP-07E 0 0 50 100 TEMPERATURE (° C) -50 PEAK-TO-PEAK AMPLITUEDE (V) OPEN-LOOP GAIN (dB) VS = ±15V TA = 25° C 80 40 0 0 1 10 100 1k 10k 100k 1M 10M FREQUENCY (Hz) 600 400 200 0 0 50 100 TEMPERATURE (° C) 28 VS = ±15V TA = 25° C 24 20 16 12 8 4 0 1k 0 ±5 ±10 ±15 ±20 POWER SUPPLY VOLTAGE (V) Maximum Output Voltage vs Load Resistance 20 15 VS = ±15V TA = 25° C VIN = ±10mV POSITIVE SWING NEGATIVE SWING 10 1M 10k 100k FREQUENCY (Hz) Output Short-Circuit Current vs Time 5 0 100 1k 10k LOAD RESISTANCE TO GROUND (Ω) Untrimmed Offset Voltage vs Temperature 35 85 1. VIN (PIN 3) = -10mV, VO = +15V 2. VIN (PIN 3) = +10mV, VO = -15V 30 1 2 25 2 1 20 VS = ±15V TA = 25° C 15 ABSOLUTE VALUE OF OFFSET VOLTAGE (µV) OUTPUT SHORT-CIRCUIT CURRENT (mA) 800 Maximum Output Swing vs Frequency Open-Loop Frequency Response 120 TA = 25° C VS = ±15V OPEN-LOOP GAIN (V/mV) INPUT OFFSET CURRENT (nA) INPUT BIAS CURRENT (nA) VS = ±15V MAXIMUM OUTPUT VOLTAGE (V) 4 -40 Open-Loop Gain vs Power Supply Voltage Input Offset Current vs Temperature Input Bias Current vs Temperature 0 1 2 3 4 TIME FROM OUTPUT BEING SHORTED (minutes) Advanced Monolithic Systems, Inc. 75 VS = ±15V RS = 100Ω OP-07C 50 OP-07E 25 0 -50 0 50 TEMPERATURE (° C) 100 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMSOP-07 TEST CIRCUITS TYPICAL OFFSET VOLTAGE TEST CIRCUIT TYPICAL LOW-FREQUENCY NOISE TEST CIRCUIT 200kΩ 2.5MΩ V+ 50kΩ 100kΩ OP-07 + VO 2 100kΩ 3 7 + 3.3kΩ 6 OP-07 OUTPUT 4 VOS = VO/4000 4.7µF V- (≈10Hz FILTER) INPUT REFERRED NOISE = VO/25,000 =(5mV/cm)/25,000 = 200nV/cm OPTIONAL OFFSET NULLING CIRCUIT 20kΩ - 2 INPUT + 3 V+ 1 8 - 7 6 OP-07 + OUTPUT 4 V- TYPICAL APPLICATIONS Adjustment Free Precision Summing Amplifier Precision Absolute Value Circuit R4 10kΩ R1 10kΩ E1 E2 E3 R2 10kΩ R3 10kΩ R3 10kΩ R4 10kΩ R5 10kΩ V+ V+ 2 3 7 - 6 OP-07 + 4 R5 2.5kΩ V- Advanced Monolithic Systems, Inc. EIN EO ±10V R1 10kΩ FD333 D1 2 7 OP-07 A1 3 + 4 R2 10kΩ V- V+ 2 6 FD333 D1 7 OP-07 A2 3 + 4 6 EO 0 TO +10V V- VA 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMSOP07 PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted. 8 LEAD SOIC PLASTIC PACKAGE (S) 0.189-0.197* (4.801-5.004) 8 7 6 5 0.228-0.244 (5.791-6.197) 0.150-0.157** (3.810-3.988) 1 2 3 4 0.010-0.020 x 45° (0.254-0.508) 0.053-0.069 (1.346-1.752) 0.004-0.010 (0.101-0.254) 0.014-0.019 (0.355-0.483) 0.008-0.010 (0.203-0.254) 0.050 (1.270) TYP 0°-8° TYP 0.016-0.050 (0.406-1.270) S (SO-8 ) AMS DRW# 042293 *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 8 LEAD PLASTIC DIP PACKAGE (P) 0.400* (10.160) MAX 8 7 6 5 1 2 3 4 0.255±0.015* (6.477±0.381) 0.045-0.065 (1.143-1.651) 0.300-0.325 (7.620-8.255) 0.130±0.005 (3.302±0.127) 0.065 (1.651) TYP 0.005 (0.127) MIN 0.100±0.010 (2.540±0.254) 0.125 (3.175) MIN 0.009-0.015 (0.229-0.381) 0.015 (0.380) MIN 0.018±0.003 (0.457±0.076) 0.325 +0.025 -0.015 (8.255 +0.635 -0.381 ) P (8L PDIP ) AMS DRW# 042294 *DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTUSIONS. MOLD FLASH OR PROTUSIONS SHALL NOT EXCEED 0.010" (0.254mm) Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140