Microsemi AGLN020V2-CSG100PP Igloo nano low power flash fpgas with flash*freeze technology Datasheet

Revision 17
IGLOO nano Low Power Flash FPGAs
with Flash*Freeze Technology
Features and Benefits
High-Performance Routing Hierarchy
Low Power
Advanced I/Os
• Segmented, Hierarchical Routing and Clock Structure
•
•
•
•
•
nanoPower Consumption—Industry’s Lowest Power
1.2 V to 1.5 V Core Voltage Support for Low Power
Supports Single-Voltage System Operation
Low Power Active FPGA Operation
Flash*Freeze Technology Enables Ultra-Low Power
Consumption while Maintaining FPGA Content
• Easy Entry to / Exit from Ultra-Low Power Flash*Freeze Mode
• 1.2 V, 1.5 V, 1.8 V, 2.5 V, and 3.3 V Mixed-Voltage Operation
• Bank-Selectable I/O Voltages—up to 4 Banks per Chip
• Single-Ended I/O Standards: LVTTL, LVCMOS
3.3 V / 2.5 V / 1.8 V / 1.5 V / 1.2 V
• Wide Range Power Supply Voltage Support per JESD8-B,
Allowing I/Os to Operate from 2.7 V to 3.6 V
• Wide Range Power Supply Voltage Support per JESD8-12,
Allowing I/Os to Operate from 1.14 V to 1.575 V
• I/O Registers on Input, Output, and Enable Paths
• Selectable Schmitt Trigger Inputs
• Hot-Swappable and Cold-Sparing I/Os
• Programmable Output Slew Rate and Drive Strength
• Weak Pull-Up/-Down
• IEEE 1149.1 (JTAG) Boundary Scan Test
• Pin-Compatible Packages across the IGLOO® Family
†
Small Footprint Packages
• As Small as 3x3 mm in Size
Wide Range of Features
• 10,000 to 250,000 System Gates
• Up to 36 kbits of True Dual-Port SRAM
• Up to 71 User I/Os
Reprogrammable Flash Technology
•
•
•
•
•
130-nm, 7-Layer Metal, Flash-Based CMOS Process
Instant On Level 0 Support
Single-Chip Solution
Retains Programmed Design When Powered Off
250 MHz (1.5 V systems) and 160 MHz (1.2 V systems) System
Performance
In-System Programming (ISP) and Security
• ISP Using On-Chip 128-Bit Advanced Encryption Standard
(AES) Decryption via JTAG (IEEE 1532–compliant)
• FlashLock® Designed to Secure FPGA Contents
• 1.2 V Programming
Clock Conditioning Circuit (CCC) and PLL
• Up to Six CCC Blocks, One with an Integrated PLL
• Configurable Phase Shift, Multiply/Divide, Delay
Capabilities, and External Feedback
• Wide Input Frequency Range (1.5 MHz up to 250 MHz)
Embedded Memory
• 1 kbit of FlashROM User Nonvolatile Memory
• SRAMs and FIFOs with Variable-Aspect-Ratio 4,608-Bit RAM
Blocks (×1, ×2, ×4, ×9, and ×18 organizations)†
• True Dual-Port SRAM (except × 18 organization)†
Enhanced Commercial Temperature Range
• Tj = -20°C to +85°C
IGLOO nano Devices
AGLN010 AGLN0151 AGLN020
IGLOO nano-Z Devices1
System Gates
AGLN060
1
AGLN030Z
AGLN060Z
AGLN125
1
AGLN250
1
AGLN125Z
AGLN250Z1
10,000
15,000
20,000
30,000
60,000
125,000
250,000
Typical Equivalent Macrocells
86
128
172
256
512
1,024
2,048
VersaTiles (D-flip-flops)
260
384
520
768
1,536
3,072
6,144
2
4
4
5
10
16
24
Flash*Freeze Mode (typical, µW)
bits)2
–
–
–
–
18
36
36
4,608-Bit Blocks2
–
–
–
–
4
8
8
FlashROM Kbits (1,024 bits)
1
1
1
1
1
1
1
Secure (AES) ISP2
–
–
–
–
Yes
Yes
Yes
Integrated PLL in CCCs 2,3
–
–
–
–
1
1
1
VersaNet Globals
4
4
4
6
18
18
18
I/O Banks
2
3
3
2
2
2
4
Maximum User I/Os (packaged device)
34
49
52
77
71
71
68
Maximum User I/Os (Known Good Die)
34
–
52
83
71
71
68
UC36
QN48
UC81,
CS81
QN68
UC81, CS81
QN48, QN68
VQ100
CS81
CS81
CS81
QN68
VQ100
VQ100
VQ100
RAM Kbits (1,024
Package Pins
UC/CS
QFN
VQFP
Notes:
1.
2.
3.
4.
Not recommended for new designs.
AGLN030 and smaller devices do not support this feature.
AGLN060, AGLN125, and AGLN250 in the CS81 package do not support PLLs.
For higher densities and support of additional features, refer to the IGLOO and IGLOOe datasheets.
† AGLN030 and smaller devices do not support this feature.
June 2013
© 2013 Microsemi Corporation
I
I/Os Per Package
IGLOO nano Devices
AGLN0151
AGLN010
AGLN020
1
AGLN060
1
IGLOO nano-Z Devices
AGLN125
1
AGLN250
1
AGLN030Z
AGLN060Z
AGLN125Z
AGLN250Z1
Known Good Die
34
–
52
83
71
71
68
UC36
23
–
–
–
–
–
–
QN48
34
–
–
34
–
–
–
QN68
–
49
49
49
–
–
–
UC81
–
–
52
66
–
–
–
CS81
–
–
52
66
60
60
60
VQ100
–
–
–
77
71
71
68
Notes:
1. Not recommended for new designs.
2. When considering migrating your design to a lower- or higher-density device, refer to the IGLOO datasheet and IGLOO FPGA
Fabric User’s Guide to ensure compliance with design and board migration requirements.
3. When the Flash*Freeze pin is used to directly enable Flash*Freeze mode and not used as a regular I/O, the number of singleended user I/Os available is reduced by one.
4. "G" indicates RoHS-compliant packages. Refer to "IGLOO nano Ordering Information" on page III for the location of the "G" in
the part number. For nano devices, the VQ100 package is offered in both leaded and RoHS-compliant versions. All other
packages are RoHS-compliant only.
Table 1 • IGLOO nano FPGAs Package Sizes Dimensions
Packages
UC36
UC81
CS81
QN48
QN68
VQ100
3x3
4x4
5x5
6x6
8x8
14 x 14
9
16
36
36
64
196
Pitch (mm)
0.4
0.4
0.5
0.4
0.4
0.5
Height (mm)
0.80
0.80
0.80
0.90
0.90
1.20
Length × Width (mm\mm)
Nominal Area
(mm2)
IGLOO nano Device Status
IGLOO nano Devices
Status
AGLN010
Production
AGLN015
Not recommended for new designs.
AGLN020
Production
IGLOO nano-Z Devices
Status
AGLN030Z
Not recommended for new designs.
AGLN060
Production
AGLN060Z
Not recommended for new designs.
AGLN125
Production
AGLN125Z
Not recommended for new designs.
AGLN250
Production
AGLN250Z
Not recommended for new designs.
II
R evis i o n 17
IGLOO nano Low Power Flash FPGAs
IGLOO nano Ordering Information
AGLN250
V2
_
Z
VQ
G
100
I
Y
Application (Temperature Range)
Blank = Enhanced Commercial (–20°C to +85°C Junction Temperature)
I = Industrial (–40°C to +100°C Junction Temperature)
PP = Pre-Production
ES = Engineering Sample (Room Temperature Only)
Security Feature
Y = Device Includes License to Implement IP Based on the
Cryptography Research, Inc. (CRI) Patent Portfolio
Blank = Device Does Not Include License to Implement IP Based
on the Cryptography Research, Inc. (CRI) Patent Portfolio
Package Lead Count
Lead-Free Packaging
Blank = Standard Packaging
G= RoHS-Compliant Packaging
Package Type
UC = Micro Chip Scale Package (0.4 mm pitch)
CS = Chip Scale Package (0.5 mm pitch)
QN = Quad Flat Pack No Leads (0.4 mm and 0.5 mm pitches)
VQ = Very Thin Quad Flat Pack (0.5 mm pitch)
DIELOT = Known Good Die
Z = nano devices without enhanced features1
Blank = Standard
Supply Voltage
2 = 1.2 V to 1.5 V
5 = 1.5 V only
Part Number
IGLOO nano Devices
AGLN010 = 10,000 System Gates
AGLN015 = 15,000 System Gates (AGLN015 is not recommended for new designs)
AGLN020 = 20,000 System Gates
AGLN030 = 30,000 System Gates
AGLN060 = 60,000 System Gates
AGLN125 = 125,000 System Gates
AGLN250 = 250,000 System Gates
Notes:
1. Z-feature grade devices AGLN060Z, AGLN125Z, and AGLN250Z do not support the enhanced nano features of Schmitt Trigger
input, bus hold (hold previous I/O state in Flash*Freeze mode), cold-sparing, hot-swap I/O capability and 1.2 V programming.
The AGLN030 Z feature grade does not support Schmitt trigger input, bus hold and 1.2 V programming. For the VQ100, CS81,
UC81, QN68, and QN48 packages, the Z feature grade and the N part number are not marked on the device. Z feature grade
devices are not recommended for new designs.
2. AGLN030 is available in the Z feature grade only.
3. Marking Information: IGLOO nano V2 devices do not have a V2 marking, but IGLOO nano V5 devices are marked with a V5
designator.
Devices Not Recommended For New Designs
AGLN015, AGLN030Z, AGLN060Z, AGLN125Z, and AGLN250Z are not recommended for new designs.
Device Marking
Microsemi normally topside marks the full ordering part number on each device. There are some exceptions to this, such as some of
the Z feature grade nano devices, the V2 designator for IGLOO devices, and packages where space is physically limited. Packages
that have limited characters available are UC36, UC81, CS81, QN48, QN68, and QFN132. On these specific packages, a subset of
the device marking will be used that includes the required legal information and as much of the part number as allowed by character
limitation of the device. In this case, devices will have a truncated device marking and may exclude the applications markings, such
as the I designator for Industrial Devices or the ES designator for Engineering Samples.
R ev i si o n 1 7
III
Figure 1 shows an example of device marking based on the AGL030V5-UCG81. The actual mark will vary by the device/package
combination ordered.
Device Name
(six characters)
Package
Wafer Lot #
Figure 1 •
Country of Origin
ACTELXXX
AGL030YWW
UCG81XXXX
XXXXXXXX
Date Code
Customer Mark
(if applicable)
Example of Device Marking for Small Form Factor Packages
IGLOO nano Products Available in the Z Feature Grade
IGLOO nano-Z Devices
Packages
AGLN030Z*
AGLN060Z*
AGLN125Z*
AGLN250Z*
QN48
–
–
–
QN68
–
–
–
UC81
–
–
–
CS81
CS81
CS81
CS81
VQ100
VQ100
VQ100
VQ100
Note: *Not recommended for new designs.
Temperature Grade Offerings
AGLN010
AGLN015*
AGLN020
Package
AGLN060
AGLN125
AGLN250
AGLN030Z*
AGLN060Z*
AGLN125Z*
AGLN250Z*
UC36
C, I
–
–
–
–
–
–
QN48
C, I
–
–
C, I
–
–
–
QN68
–
C, I
C, I
C, I
–
–
–
UC81
–
–
C, I
C, I
–
–
–
CS81
–
–
C, I
C, I
C, I
C, I
C, I
–
–
–
C, I
C, I
C, I
C, I
VQ100
Note:
* Not
recommended for new designs.
C = Enhanced Commercial temperature range: –20°C to +85°C junction temperature
I = Industrial temperature range: –40°C to +100°C junction temperature
Contact your local Microsemi representative for device availability: http://www.microsemi.com/soc/contact/default.aspx.
IV
Revision 17
IGLOO nano Low Power Flash FPGAs
Table of Contents
IGLOO nano Device Overview
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
IGLOO nano DC and Switching Characteristics
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Calculating Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
User I/O Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
VersaTile Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-57
Global Resource Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-63
Clock Conditioning Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-70
Embedded SRAM and FIFO Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-73
Embedded FlashROM Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-87
JTAG 1532 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-88
Pin Descriptions
Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
JTAG Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Function Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1
3-2
3-3
3-4
3-4
3-5
Package Pin Assignments
UC36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
UC81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
CS81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
QN48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15
QN68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18
VQ100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22
Datasheet Information
List of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Datasheet Categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Safety Critical, Life Support, and High-Reliability Applications Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
R ev i si o n 1 7
V
1 – IGLOO nano Device Overview
General Description
The IGLOO family of flash FPGAs, based on a 130-nm flash process, offers the lowest power FPGA, a
single-chip solution, small footprint packages, reprogrammability, and an abundance of advanced
features.
The Flash*Freeze technology used in IGLOO nano devices enables entering and exiting an ultra-low
power mode that consumes nanoPower while retaining SRAM and register data. Flash*Freeze
technology simplifies power management through I/O and clock management with rapid recovery to
operation mode.
The Low Power Active capability (static idle) allows for ultra-low power consumption while the IGLOO
nano device is completely functional in the system. This allows the IGLOO nano device to control system
power management based on external inputs (e.g., scanning for keyboard stimulus) while consuming
minimal power.
Nonvolatile flash technology gives IGLOO nano devices the advantage of being a secure, low power,
single-chip solution that is Instant On. The IGLOO nano device is reprogrammable and offers time-tomarket benefits at an ASIC-level unit cost.
These features enable designers to create high-density systems using existing ASIC or FPGA design
flows and tools.
IGLOO nano devices offer 1 kbit of on-chip, reprogrammable, nonvolatile FlashROM storage as well as
clock conditioning circuitry based on an integrated phase-locked loop (PLL). The AGLN030 and smaller
devices have no PLL or RAM support. IGLOO nano devices have up to 250 k system gates, supported
with up to 36 kbits of true dual-port SRAM and up to 71 user I/Os.
IGLOO nano devices increase the breadth of the IGLOO product line by adding new features and
packages for greater customer value in high volume consumer, portable, and battery-backed markets.
Features such as smaller footprint packages designed with two-layer PCBs in mind, power consumption
measured in nanoPower, Schmitt trigger, and bus hold (hold previous I/O state in Flash*Freeze mode)
functionality make these devices ideal for deployment in applications that require high levels of flexibility
and low cost.
Flash*Freeze Technology
The IGLOO nano device offers unique Flash*Freeze technology, allowing the device to enter and exit
ultra-low power Flash*Freeze mode. IGLOO nano devices do not need additional components to turn off
I/Os or clocks while retaining the design information, SRAM content, and registers. Flash*Freeze
technology is combined with in-system programmability, which enables users to quickly and easily
upgrade and update their designs in the final stages of manufacturing or in the field. The ability of IGLOO
nano V2 devices to support a wide range of core voltage (1.2 V to 1.5 V) allows further reduction in
power consumption, thus achieving the lowest total system power.
During Flash*Freeze mode, each I/O can be set to the following configurations: hold previous state,
tristate, HIGH, or LOW.
The availability of low power modes, combined with reprogrammability, a single-chip and single-voltage
solution, and small-footprint packages make IGLOO nano devices the best fit for portable electronics.
R ev i si o n 1 7
1 -1
IGLOO nano Device Overview
Flash Advantages
Low Power
Flash-based IGLOO nano devices exhibit power characteristics similar to those of an ASIC, making them
an ideal choice for power-sensitive applications. IGLOO nano devices have only a very limited power-on
current surge and no high-current transition period, both of which occur on many FPGAs.
IGLOO nano devices also have low dynamic power consumption to further maximize power savings;
power is reduced even further by the use of a 1.2 V core voltage.
Low dynamic power consumption, combined with low static power consumption and Flash*Freeze
technology, gives the IGLOO nano device the lowest total system power offered by any FPGA.
Security
Nonvolatile, flash-based IGLOO nano devices do not require a boot PROM, so there is no vulnerable
external bitstream that can be easily copied. IGLOO nano devices incorporate FlashLock, which provides
a unique combination of reprogrammability and design security without external overhead, advantages
that only an FPGA with nonvolatile flash programming can offer.
IGLOO nano devices utilize a 128-bit flash-based lock and a separate AES key to provide the highest
level of security in the FPGA industry for programmed intellectual property and configuration data. In
addition, all FlashROM data in IGLOO nano devices can be encrypted prior to loading, using the
industry-leading AES-128 (FIPS192) bit block cipher encryption standard. AES was adopted by the
National Institute of Standards and Technology (NIST) in 2000 and replaces the 1977 DES standard.
IGLOO nano devices have a built-in AES decryption engine and a flash-based AES key that make them
the most comprehensive programmable logic device security solution available today. IGLOO nano
devices with AES-based security provide a high level of protection for remote field updates over public
networks such as the Internet, and are designed to ensure that valuable IP remains out of the hands of
system overbuilders, system cloners, and IP thieves.
Security, built into the FPGA fabric, is an inherent component of IGLOO nano devices. The flash cells are
located beneath seven metal layers, and many device design and layout techniques have been used to
make invasive attacks extremely difficult. IGLOO nano devices, with FlashLock and AES security, are
unique in being highly resistant to both invasive and noninvasive attacks. Your valuable IP is protected
with industry-standard security, making remote ISP possible. An IGLOO nano device provides the best
available security for programmable logic designs.
Single Chip
Flash-based FPGAs store their configuration information in on-chip flash cells. Once programmed, the
configuration data is an inherent part of the FPGA structure, and no external configuration data needs to
be loaded at system power-up (unlike SRAM-based FPGAs). Therefore, flash-based IGLOO nano
FPGAs do not require system configuration components such as EEPROMs or microcontrollers to load
device configuration data. This reduces bill-of-materials costs and PCB area, and increases security and
system reliability.
Instant On
Microsemi flash-based IGLOO nano devices support Level 0 of the Instant On classification standard.
This feature helps in system component initialization, execution of critical tasks before the processor
wakes up, setup and configuration of memory blocks, clock generation, and bus activity management.
The Instant On feature of flash-based IGLOO nano devices greatly simplifies total system design and
reduces total system cost, often eliminating the need for CPLDs and clock generation PLLs. In addition,
glitches and brownouts in system power will not corrupt the IGLOO nano device's flash configuration,
and unlike SRAM-based FPGAs, the device will not have to be reloaded when system power is restored.
This enables the reduction or complete removal of the configuration PROM, expensive voltage monitor,
brownout detection, and clock generator devices from the PCB design. Flash-based IGLOO nano
devices simplify total system design and reduce cost and design risk while increasing system reliability
and improving system initialization time.
IGLOO nano flash FPGAs enable the user to quickly enter and exit Flash*Freeze mode. This is done
almost instantly (within 1 µs) and the device retains configuration and data in registers and RAM. Unlike
SRAM-based FPGAs, the device does not need to reload configuration and design state from external
memory components; instead it retains all necessary information to resume operation immediately.
1- 2
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
Reduced Cost of Ownership
Advantages to the designer extend beyond low unit cost, performance, and ease of use. Unlike
SRAM-based FPGAs, flash-based IGLOO nano devices allow all functionality to be Instant On; no
external boot PROM is required. On-board security mechanisms prevent access to all the programming
information and enable secure remote updates of the FPGA logic.
Designers can perform secure remote in-system reprogramming to support future design iterations and
field upgrades with confidence that valuable intellectual property cannot be compromised or copied.
Secure ISP can be performed using the industry-standard AES algorithm. The IGLOO nano device
architecture mitigates the need for ASIC migration at higher user volumes. This makes IGLOO nano
devices cost-effective ASIC replacement solutions, especially for applications in the consumer,
networking/communications, computing, and avionics markets.
With a variety of devices under $1, IGLOO nano FPGAs enable cost-effective implementation of
programmable logic and quick time to market.
Firm-Error Immunity
Firm errors occur most commonly when high-energy neutrons, generated in the upper atmosphere, strike
a configuration cell of an SRAM FPGA. The energy of the collision can change the state of the
configuration cell and thus change the logic, routing, or I/O behavior in an unpredictable way. These
errors are impossible to prevent in SRAM FPGAs. The consequence of this type of error can be a
complete system failure. Firm errors do not exist in the configuration memory of IGLOO nano flash-based
FPGAs. Once it is programmed, the flash cell configuration element of IGLOO nano FPGAs cannot be
altered by high-energy neutrons and is therefore immune to them. Recoverable (or soft) errors occur in
the user data SRAM of all FPGA devices. These can easily be mitigated by using error detection and
correction (EDAC) circuitry built into the FPGA fabric.
Advanced Flash Technology
The IGLOO nano device offers many benefits, including nonvolatility and reprogrammability, through an
advanced flash-based, 130-nm LVCMOS process with seven layers of metal. Standard CMOS design
techniques are used to implement logic and control functions. The combination of fine granularity,
enhanced flexible routing resources, and abundant flash switches allows for very high logic utilization
without compromising device routability or performance. Logic functions within the device are
interconnected through a four-level routing hierarchy.
IGLOO nano FPGAs utilize design and process techniques to minimize power consumption in all modes
of operation.
Advanced Architecture
The proprietary IGLOO nano architecture provides granularity comparable to standard-cell ASICs. The
IGLOO nano device consists of five distinct and programmable architectural features (Figure 1-3 on
page 1-5 to Figure 1-4 on page 1-5):
•
Flash*Freeze technology
•
FPGA VersaTiles
•
Dedicated FlashROM
•
Dedicated SRAM/FIFO memory†
•
Extensive CCCs and PLLs†
•
Advanced I/O structure
The FPGA core consists of a sea of VersaTiles. Each VersaTile can be configured as a three-input logic
function, a D-flip-flop (with or without enable), or a latch by programming the appropriate flash switch
interconnections. The versatility of the IGLOO nano core tile as either a three-input lookup table (LUT)
equivalent or a D-flip-flop/latch with enable allows for efficient use of the FPGA fabric. The VersaTile
capability is unique to the ProASIC® family of third-generation-architecture flash FPGAs. VersaTiles are
connected with any of the four levels of routing hierarchy. Flash switches are distributed throughout the
device to provide nonvolatile, reconfigurable interconnect programming. Maximum core utilization is
possible for virtually any design.
† The AGLN030 and smaller devices do not support PLL or SRAM.
R ev i si o n 1 7
1 -3
IGLOO nano Device Overview
Bank 1*
I/Os
Bank 1
Bank 0
VersaTile
User Nonvolatile
FlashROM
Flash*Freeze
Technology
Charge
Pumps
CCC-GL
Bank 1
Note: *Bank 0 for the AGLN030 device
Figure 1-1 • IGLOO Device Architecture Overview with Two I/O Banks and No RAM (AGLN010 and AGLN030)
Bank 1
I/Os
Bank 2
Bank 0
VersaTile
User Nonvolatile
FlashRom
Flash*Freeze
Technology
Charge
Pumps
CCC-GL
Bank 1
Figure 1-2 •
1- 4
IGLOO Device Architecture Overview with Three I/O Banks and No RAM (AGLN015 and
AGLN020)
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
.
Bank 0
Bank 0
Bank 1
CCC
RAM Block
4,608-Bit Dual-Port
SRAM or FIFO Block
I/Os
ISP AES
Decryption
User Nonvolatile
FlashRom
Flash*Freeze
Technology
Charge
Pumps
Bank 0
Bank 1
VersaTile
Bank 1
Figure 1-3 •
IGLOO Device Architecture Overview with Two I/O Banks (AGLN060, AGLN125)
Bank 0
Bank 1
Bank 3
CCC
RAM Block
4,608-Bit Dual-Port
SRAM or FIFO Block
Bank 1
Bank 3
I/Os
ISP AES
Decryption
User Nonvolatile
FlashRom
Flash*Freeze
Technology
VersaTile
Charge
Pumps
Bank 2
Figure 1-4 •
IGLOO Device Architecture Overview with Four I/O Banks (AGLN250)
R ev i si o n 1 7
1 -5
IGLOO nano Device Overview
Flash*Freeze Technology
The IGLOO nano device has an ultra-low power static mode, called Flash*Freeze mode, which retains all
SRAM and register information and can still quickly return to normal operation. Flash*Freeze technology
enables the user to quickly (within 1 µs) enter and exit Flash*Freeze mode by activating the
Flash*Freeze pin while all power supplies are kept at their original values. I/Os, global I/Os, and clocks
can still be driven and can be toggling without impact on power consumption, and the device retains all
core registers, SRAM information, and I/O states. I/Os can be individually configured to either hold their
previous state or be tristated during Flash*Freeze mode.
Alternatively, I/Os can be set to a specific state using weak pull-up or pull-down I/O attribute
configuration. No power is consumed by the I/O banks, clocks, JTAG pins, or PLL, and the device
consumes as little as 2 µW in this mode.
Flash*Freeze technology allows the user to switch to Active mode on demand, thus simplifying the power
management of the device.
The Flash*Freeze pin (active low) can be routed internally to the core to allow the user's logic to decide
when it is safe to transition to this mode. Refer to Figure 1-5 for an illustration of entering/exiting
Flash*Freeze mode. It is also possible to use the Flash*Freeze pin as a regular I/O if Flash*Freeze mode
usage is not planned.
IGLOO nano
FPGA
Flash*Freeze
Mode Control
Flash*Freeze Pin
Figure 1-5 •
IGLOO nano Flash*Freeze Mode
VersaTiles
The IGLOO nano core consists of VersaTiles, which have been enhanced beyond the ProASICPLUS®
core tiles. The IGLOO nano VersaTile supports the following:
•
All 3-input logic functions—LUT-3 equivalent
•
Latch with clear or set
•
D-flip-flop with clear or set
•
Enable D-flip-flop with clear or set
Refer to Figure 1-6 for VersaTile configurations.
LUT-3 Equivalent
X1
X2
X3
LUT-3
Y
D-Flip-Flop with Clear or Set
Data
CLK
CLR
Y
D-FF
Enable D-Flip-Flop with Clear or Set
Data
CLK
Enable
CLR
Figure 1-6 •
1- 6
VersaTile Configurations
R ev isio n 1 7
Y
D-FF
IGLOO nano Low Power Flash FPGAs
User Nonvolatile FlashROM
IGLOO nano devices have 1 kbit of on-chip, user-accessible, nonvolatile FlashROM. The FlashROM can
be used in diverse system applications:
•
Internet protocol addressing (wireless or fixed)
•
System calibration settings
•
Device serialization and/or inventory control
•
Subscription-based business models (for example, set-top boxes)
•
Secure key storage for secure communications algorithms
•
Asset management/tracking
•
Date stamping
•
Version management
The FlashROM is written using the standard IGLOO nano IEEE 1532 JTAG programming interface. The
core can be individually programmed (erased and written), and on-chip AES decryption can be used
selectively to securely load data over public networks (except in the AGLN030 and smaller devices), as
in security keys stored in the FlashROM for a user design.
The FlashROM can be programmed via the JTAG programming interface, and its contents can be read
back either through the JTAG programming interface or via direct FPGA core addressing. Note that the
FlashROM can only be programmed from the JTAG interface and cannot be programmed from the
internal logic array.
The FlashROM is programmed as 8 banks of 128 bits; however, reading is performed on a byte-by-byte
basis using a synchronous interface. A 7-bit address from the FPGA core defines which of the 8 banks
and which of the 16 bytes within that bank are being read. The three most significant bits (MSBs) of the
FlashROM address determine the bank, and the four least significant bits (LSBs) of the FlashROM
address define the byte.
The IGLOO nano development software solutions, Libero® System-on-Chip (SoC) and Designer, have
extensive support for the FlashROM. One such feature is auto-generation of sequential programming
files for applications requiring a unique serial number in each part. Another feature enables the inclusion
of static data for system version control. Data for the FlashROM can be generated quickly and easily
using Microsemi Libero SoC and Designer software tools. Comprehensive programming file support is
also included to allow for easy programming of large numbers of parts with differing FlashROM contents.
SRAM and FIFO
IGLOO nano devices (except the AGLN030 and smaller devices) have embedded SRAM blocks along
their north and south sides. Each variable-aspect-ratio SRAM block is 4,608 bits in size. Available
memory configurations are 256×18, 512×9, 1k×4, 2k×2, and 4k×1 bits. The individual blocks have
independent read and write ports that can be configured with different bit widths on each port. For
example, data can be sent through a 4-bit port and read as a single bitstream. The embedded SRAM
blocks can be initialized via the device JTAG port (ROM emulation mode) using the UJTAG macro
(except in the AGLN030 and smaller devices).
In addition, every SRAM block has an embedded FIFO control unit. The control unit allows the SRAM
block to be configured as a synchronous FIFO without using additional core VersaTiles. The FIFO width
and depth are programmable. The FIFO also features programmable Almost Empty (AEMPTY) and
Almost Full (AFULL) flags in addition to the normal Empty and Full flags. The embedded FIFO control
unit contains the counters necessary for generation of the read and write address pointers. The
embedded SRAM/FIFO blocks can be cascaded to create larger configurations.
PLL and CCC
Higher density IGLOO nano devices using either the two I/O bank or four I/O bank architectures provide
designers with very flexible clock conditioning capabilities. AGLN060, AGLN125, and AGLN250 contain
six CCCs. One CCC (center west side) has a PLL. The AGLN030 and smaller devices use different
CCCs in their architecture (CCC-GL). These CCC-GLs contain a global MUX but do not have any PLLs
or programmable delays.
For devices using the six CCC block architecture, these are located at the four corners and the centers of
the east and west sides. All six CCC blocks are usable; the four corner CCCs and the east CCC allow
simple clock delay operations as well as clock spine access.
R ev i si o n 1 7
1 -7
IGLOO nano Device Overview
The inputs of the six CCC blocks are accessible from the FPGA core or from dedicated connections to
the CCC block, which are located near the CCC.
The CCC block has these key features:
•
Wide input frequency range (fIN_CCC) = 1.5 MHz up to 250 MHz
•
Output frequency range (fOUT_CCC) = 0.75 MHz up to 250 MHz
•
2 programmable delay types for clock skew minimization
•
Clock frequency synthesis (for PLL only)
Additional CCC specifications:
•
Internal phase shift = 0°, 90°, 180°, and 270°. Output phase shift depends on the output divider
configuration (for PLL only).
•
Output duty cycle = 50% ± 1.5% or better (for PLL only)
•
Low output jitter: worst case < 2.5% × clock period peak-to-peak period jitter when single global
network used (for PLL only)
•
Maximum acquisition time is 300 µs (for PLL only)
•
Exceptional tolerance to input period jitter—allowable input jitter is up to 1.5 ns (for PLL only)
•
Four precise phases; maximum misalignment between adjacent phases of 40 ps × 250 MHz /
fOUT_CCC (for PLL only)
Global Clocking
IGLOO nano devices have extensive support for multiple clocking domains. In addition to the CCC and
PLL support described above, there is a comprehensive global clock distribution network.
Each VersaTile input and output port has access to nine VersaNets: six chip (main) and three quadrant
global networks. The VersaNets can be driven by the CCC or directly accessed from the core via
multiplexers (MUXes). The VersaNets can be used to distribute low-skew clock signals or for rapid
distribution of high-fanout nets.
I/Os with Advanced I/O Standards
IGLOO nano FPGAs feature a flexible I/O structure, supporting a range of voltages (1.2 V, 1.2 V wide
range, 1.5 V, 1.8 V, 2.5 V, 3.0 V wide range, and 3.3 V).
The I/Os are organized into banks with two, three, or four banks per device. The configuration of these
banks determines the I/O standards supported.
Each I/O module contains several input, output, and enable registers. These registers allow the
implementation of various single-data-rate applications for all versions of nano devices and double-datarate applications for the AGLN060, AGLN125, and AGLN250 devices.
IGLOO nano devices support LVTTL and LVCMOS I/O standards, are hot-swappable, and support coldsparing and Schmitt trigger.
Hot-swap (also called hot-plug, or hot-insertion) is the operation of hot-insertion or hot-removal of a card
in a powered-up system.
Cold-sparing (also called cold-swap) refers to the ability of a device to leave system data undisturbed
when the system is powered up, while the component itself is powered down, or when power supplies
are floating.
Wide Range I/O Support
IGLOO nano devices support JEDEC-defined wide range I/O operation. IGLOO nano devices support
both the JESD8-B specification, covering both 3 V and 3.3 V supplies, for an effective operating range of
2.7 V to 3.6 V, and JESD8-12 with its 1.2 V nominal, supporting an effective operating range of 1.14 V to
1.575 V.
Wider I/O range means designers can eliminate power supplies or power conditioning components from
the board or move to less costly components with greater tolerances. Wide range eases I/O bank
management and provides enhanced protection from system voltage spikes, while providing the flexibility
to easily run custom voltage applications.
1- 8
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
Specifying I/O States During Programming
You can modify the I/O states during programming in FlashPro. In FlashPro, this feature is supported for
PDB files generated from Designer v8.5 or greater. See the FlashPro User’s Guide for more information.
Note: PDB files generated from Designer v8.1 to Designer v8.4 (including all service packs) have
limited display of Pin Numbers only.
1. Load a PDB from the FlashPro GUI. You must have a PDB loaded to modify the I/O states during
programming.
2. From the FlashPro GUI, click PDB Configuration. A FlashPoint – Programming File Generator
window appears.
3. Click the Specify I/O States During Programming button to display the Specify I/O States During
Programming dialog box.
4. Sort the pins as desired by clicking any of the column headers to sort the entries by that header.
Select the I/Os you wish to modify (Figure 1-7 on page 1-9).
5. Set the I/O Output State. You can set Basic I/O settings if you want to use the default I/O settings
for your pins, or use Custom I/O settings to customize the settings for each pin. Basic I/O state
settings:
1 – I/O is set to drive out logic High
0 – I/O is set to drive out logic Low
Last Known State – I/O is set to the last value that was driven out prior to entering the
programming mode, and then held at that value during programming
Z -Tri-State: I/O is tristated
Figure 1-7 •
I/O States During Programming Window
R ev i si o n 1 7
1 -9
IGLOO nano Device Overview
6. Click OK to return to the FlashPoint – Programming File Generator window.
Note: I/O States During programming are saved to the ADB and resulting programming files after
completing programming file generation.
1- 10
R ev i sio n 1 7
2 – IGLOO nano DC and Switching Characteristics
General Specifications
The Z feature grade does not support the enhanced nano features of Schmitt trigger input, Flash*Freeze
bus hold (hold previous I/O state in Flash*Freeze mode), cold-sparing, and hot-swap I/O capability. Refer
to "IGLOO nano Ordering Information" on page III for more information.
Operating Conditions
Stresses beyond those listed in Table 2-1 may cause permanent damage to the device.
Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Absolute Maximum Ratings are stress ratings only; functional operation of the device at these or any
other conditions beyond those listed under the Recommended Operating Conditions specified in
Table 2-2 on page 2-2 is not implied.
Table 2-1 •
Absolute Maximum Ratings
Symbol
Parameter
Limits
Units
VCC
DC core supply voltage
–0.3 to 1.65
V
VJTAG
JTAG DC voltage
–0.3 to 3.75
V
VPUMP
Programming voltage
–0.3 to 3.75
V
VCCPLL
Analog power supply (PLL)
–0.3 to 1.65
V
VCCI
DC I/O buffer supply voltage
–0.3 to 3.75
V
–0.3 V to 3.6 V
V
Storage temperature
–65 to +150
°C
Junction temperature
+125
°C
1
I/O input voltage
VI
TSTG
2
TJ 2
Notes:
1. The device should be operated within the limits specified by the datasheet. During transitions, the input signal may
undershoot or overshoot according to the limits shown in Table 2-4 on page 2-3.
2. For flash programming and retention maximum limits, refer to Table 2-3 on page 2-2, and for recommended operating
limits, refer to Table 2-2 on page 2-2.
R ev i si o n 1 7
2 -1
IGLOO nano DC and Switching Characteristics
Recommended Operating Conditions 1
Table 2-2 •
Symbol
Extended
Commercial
Parameter
2
Junction temperature
TJ
VCC
°C
1.425 to 1.575
1.425 to 1.575
V
1.14 to 1.575
1.14 to 1.575
V
1.4 to 3.6
1.4 to 3.6
V
3.15 to 3.45
3.15 to 3.45
V
0 to 3.6
0 to 3.6
V
1.425 to 1.575
1.425 to 1.575
V
1.14 to 1.575
1.14 to 1.575
V
1.14 to 1.26
1.14 to 1.26
V
1.14 to 1.575
1.14 to 1.575
V
1.5 V DC supply voltage
1.425 to 1.575
1.425 to 1.575
V
1.8 V DC supply voltage
1.7 to 1.9
1.7 to 1.9
V
2.5 V DC supply voltage
2.3 to 2.7
2.3 to 2.7
V
3.0 to 3.6
3.0 to 3.6
V
2.7 to 3.6
2.7 to 3.6
V
voltage3
1.2 V–1.5 V wide range core voltage4,5
VJTAG
VPUMP
JTAG DC voltage
6
Units
2
–40 to +100
1.5 V DC core supply
–20 to + 85
Industrial
Programming voltage
Programming mode
Operation
VCCPLL7 Analog power supply 1.5 V DC core supply voltage3
(PLL)
1.2 V–1.5 V wide range core
supply voltage4
VCCI and 1.2 V DC supply voltage 4
VMV 8,9
1.2 V DC wide range supply voltage 4
3.3 V DC supply voltage
3.3 V DC wide range supply voltage
10
Notes:
1. All parameters representing voltages are measured with respect to GND unless otherwise specified.
2. Default Junction Temperature Range in the Libero SoC software is set to 0°C to +70°C for commercial, and -40°C to
+85°C for industrial. To ensure targeted reliability standards are met across the full range of junction temperatures,
Microsemi recommends using custom settings for temperature range before running timing and power analysis tools.
For more information regarding custom settings, refer to the New Project Dialog Box in the Libero Online Help.
3. For IGLOO® nano V5 devices
4. For IGLOO nano V2 devices only, operating at VCCI VCC
5. IGLOO nano V5 devices can be programmed with the VCC core voltage at 1.5 V only. IGLOO nano V2 devices can be
programmed with the VCC core voltage at 1.2 V (with FlashPro4 only) or 1.5 V. If you are using FlashPro3 and want to
do in-system programming using 1.2 V, please contact the factory.
6. VPUMP can be left floating during operation (not programming mode).
7. VCCPLL pins should be tied to VCC pins. See the "Pin Descriptions" chapter for further information.
8. VMV pins must be connected to the corresponding VCCI pins. See the Pin Descriptions chapter of the IGLOO nano
FPGA Fabric User’s Guide for further information.
9. The ranges given here are for power supplies only. The recommended input voltage ranges specific to each I/O
standard are given in Table 2-21 on page 2-19. VCCI should be at the same voltage within a given I/O bank.
10. 3.3 V wide range is compliant to the JESD8-B specification and supports 3.0 V VCCI operation.
Table 2-3 •
Product
Grade
Flash Programming Limits – Retention, Storage, and Operating Temperature1
Programming
Cycles
Program Retention
Maximum Storage
Maximum Operating Junction
(biased/unbiased) Temperature TSTG (°C) 2
Temperature TJ (°C) 2
Commercial
500
20 years
110
100
Industrial
500
20 years
110
100
Notes:
1. This is a stress rating only; functional operation at any condition other than those indicated is not implied.
2. These limits apply for program/data retention only. Refer to Table 2-1 on page 2-1 and Table 2-2 for device operating
conditions and absolute limits.
2- 2
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
Table 2-4 •
Overshoot and Undershoot Limits 1
VCCI
Average VCCI–GND Overshoot or
Undershoot Duration
as a Percentage of Clock Cycle2
Maximum Overshoot/
Undershoot2
10%
1.4 V
5%
1.49 V
10%
1.1 V
5%
1.19 V
10%
0.79 V
5%
0.88 V
10%
0.45 V
5%
0.54 V
2.7 V or less
3V
3.3 V
3.6 V
Notes:
1. Based on reliability requirements at 85°C.
2. The duration is allowed at one out of six clock cycles. If the overshoot/undershoot occurs at one out of two cycles, the
maximum overshoot/undershoot has to be reduced by 0.15 V.
I/O Power-Up and Supply Voltage Thresholds for Power-On Reset
(Commercial and Industrial)
Sophisticated power-up management circuitry is designed into every IGLOO nano device. These circuits
ensure easy transition from the powered-off state to the powered-up state of the device. The many
different supplies can power up in any sequence with minimized current spikes or surges. In addition, the
I/O will be in a known state through the power-up sequence. The basic principle is shown in Figure 2-1
on page 2-4.
There are five regions to consider during power-up.
IGLOO nano I/Os are activated only if ALL of the following three conditions are met:
1. VCC and VCCI are above the minimum specified trip points (Figure 2-1 and Figure 2-2 on
page 2-5).
2. VCCI > VCC – 0.75 V (typical)
3. Chip is in the operating mode.
VCCI Trip Point:
Ramping up (V5 devices): 0.6 V < trip_point_up < 1.2 V
Ramping down (V5 devices): 0.5 V < trip_point_down < 1.1 V
Ramping up (V2 devices): 0.75 V < trip_point_up < 1.05 V
Ramping down (V2 devices): 0.65 V < trip_point_down < 0.95 V
VCC Trip Point:
Ramping up (V5 devices): 0.6 V < trip_point_up < 1.1 V
Ramping down (V5 devices): 0.5 V < trip_point_down < 1.0 V
Ramping up (V2 devices): 0.65 V < trip_point_up < 1.05 V
Ramping down (V2 devices): 0.55 V < trip_point_down < 0.95 V
VCC and VCCI ramp-up trip points are about 100 mV higher than ramp-down trip points. This specifically
built-in hysteresis prevents undesirable power-up oscillations and current surges. Note the following:
•
During programming, I/Os become tristated and weakly pulled up to VCCI.
•
JTAG supply, PLL power supplies, and charge pump VPUMP supply have no influence on I/O
behavior.
R ev i si o n 1 7
2 -3
IGLOO nano DC and Switching Characteristics
PLL Behavior at Brownout Condition
Microsemi recommends using monotonic power supplies or voltage regulators to ensure proper powerup behavior. Power ramp-up should be monotonic at least until VCC and VCCPLX exceed brownout
activation levels (see Figure 2-1 and Figure 2-2 on page 2-5 for more details).
When PLL power supply voltage and/or VCC levels drop below the VCC brownout levels (0.75 V ± 0.25
V for V5 devices, and 0.75 V ± 0.2 V for V2 devices), the PLL output lock signal goes LOW and/or the
output clock is lost. Refer to the "Brownout Voltage" section in the "Power-Up/-Down Behavior of Low
Power Flash Devices" chapter of the IGLOO nano FPGA Fabric User’s Guide for information on clock
and lock recovery.
Internal Power-Up Activation Sequence
1. Core
2. Input buffers
3. Output buffers, after 200 ns delay from input buffer activation
To make sure the transition from input buffers to output buffers is clean, ensure that there is no path
longer than 100 ns from input buffer to output buffer in your design.
VCC = VCCI + VT
where VT can be from 0.58 V to 0.9 V (typically 0.75 V)
VCC
VCC = 1.575 V
Region 4: I/O
buffers are ON.
Region 1: I/O Buffers are OFF
I/Os are functional
but slower because VCCI
is below specification. For the
same reason, input buffers do not
Region 5: I/O buffers are ON
and power supplies are within
specification.
I/Os meet the entire datasheet
and timer specifications for
speed, VIH / VIL , VOH / VOL , etc.
meet VIH / VIL levels, and output
buffers do not meet VOH/VOL levels.
VCC = 1.425 V
Region 2: I/O buffers are ON.
I/Os are functional but slower because
VCCI / VCC are below specification. For the
same reason, input buffers do not meet
VIH/VIL levels, and output buffers to not
Region 3: I/O buffers are ON.
I/Os are functional; I/O DC
specifications are met,
but I/Os are slower because
the VCC is below specification.
meet VOH / VOL levels.
Activation trip point:
Va = 0.85 V ± 0.25 V
Deactivation trip point:
Vd = 0.75 V ± 0.25 V
Region 1: I/O buffers are OFF
Activation trip point:
Va = 0.9 V ± 0.3 V
Deactivation trip point:
Vd = 0.8 V ± 0.3 V
Figure 2-1 •
2- 4
Min VCCI datasheet specification
voltage at a selected I/O
standard; i.e., 1.425 V or 1.7 V
or 2.3 V or 3.0 V
V5 Devices – I/O State as a Function of VCCI and VCC Voltage Levels
R ev isio n 1 7
VCCI
IGLOO nano Low Power Flash FPGAs
VCC = VCCI + VT
where VT can be from 0.58 V to 0.9 V (typically 0.75 V)
VCC
VCC = 1.575 V
Region 1: I/O Buffers are OFF
Region 4: I/O
buffers are ON.
I/Os are functional
but slower because VCCI
is below specification. For the
Region 5: I/O buffers are ON
and power supplies are within
specification.
I/Os meet the entire datasheet
and timer specifications for
speed, VIH / VIL , VOH / VOL , etc.
same reason, input buffers do not
meet VIH / VIL levels, and output
buffers do not meet VOH / VOL levels.
VCC = 1.14 V
Region 2: I/O buffers are ON.
I/Os are functional but slower because
VCCI / VCC are below specification. For the
same reason, input buffers do not meet
VIH / VIL levels, and output buffers do not
meet VOH/VOL levels.
Activation trip point:
Va = 0.85 V ± 0.2 V
Deactivation trip point:
Vd = 0.75 V ± 0.2 V
Region 1: I/O buffers are OFF
Activation trip point:
Va = 0.9 V ± 0.15 V
Deactivation trip point:
Vd = 0.8 V ± 0.15 V
Figure 2-2 •
Region 3: I/O buffers are ON.
I/Os are functional; I/O DC
specifications are met,
but I/Os are slower because
the VCC is below specification.
Min VCCI datasheet specification
voltage at a selected I/O
standard; i.e., 1.14 V,1.425 V, 1.7 V,
2.3 V, or 3.0 V
VCCI
V2 Devices – I/O State as a Function of VCCI and VCC Voltage Levels
R ev i si o n 1 7
2 -5
IGLOO nano DC and Switching Characteristics
Thermal Characteristics
Introduction
The temperature variable in the Microsemi Designer software refers to the junction temperature, not the
ambient temperature. This is an important distinction because dynamic and static power consumption
cause the chip junction temperature to be higher than the ambient temperature.
EQ 1 can be used to calculate junction temperature.
TJ = Junction Temperature = T + TA
EQ 1
where:
TA = Ambient temperature
T = Temperature gradient between junction (silicon) and ambient T = ja * P
ja = Junction-to-ambient of the package. ja numbers are located in Figure 2-5.
P = Power dissipation
Package Thermal Characteristics
The device junction-to-case thermal resistivity is jc and the junction-to-ambient air thermal resistivity is
ja. The thermal characteristics for ja are shown for two air flow rates. The maximum operating junction
temperature is 100°C. EQ 2 shows a sample calculation of the maximum operating power dissipation
allowed for a 484-pin FBGA package at commercial temperature and in still air.
Max. junction temp. (C) – Max. ambient temp. (C) 100C – 70C
Maximum Power Allowed = ------------------------------------------------------------------------------------------------------------------------------------------ = ------------------------------------- = 1.46 W
 ja (C/W)
20.5°C/W
EQ 2
Table 2-5 •
Package Thermal Resistivities
ja
Package Type
Chip Scale Package (CSP)
Quad Flat No Lead (QFN)
Very Thin Quad Flat Pack (VQFP)
Pin
Count
jc
Still Air
200 ft./
min.
500 ft./
min.
Units
36
TBD
TBD
TBD
TBD
C/W
81
TBD
TBD
TBD
TBD
C/W
48
TBD
TBD
TBD
TBD
C/W
68
TBD
TBD
TBD
TBD
C/W
100
TBD
TBD
TBD
TBD
C/W
100
10.0
35.3
29.4
27.1
C/W
Temperature and Voltage Derating Factors
Table 2-6 • Temperature and Voltage Derating Factors for Timing Delays (normalized to TJ = 70°C,
VCC = 1.425 V)
For IGLOO nano V2 or V5 Devices, 1.5 V DC Core Supply Voltage
Junction Temperature (°C)
Array Voltage
VCC (V)
–40°C
–20°C
0°C
25°C
70°C
85°C
100°C
1.425
0.947
0.956
0.965
0.978
1.000
1.009
1.013
1.5
0.875
0.883
0.892
0.904
0.925
0.932
0.937
1.575
0.821
0.829
0.837
0.848
0.868
0.875
0.879
2- 6
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
Table 2-7 • Temperature and Voltage Derating Factors for Timing Delays (normalized to TJ = 70°C,
VCC = 1.14 V)
For IGLOO nano V2, 1.2 V DC Core Supply Voltage
Junction Temperature (°C)
Array Voltage
VCC (V)
–40°C
–20°C
0°C
25°C
70°C
85°C
100°C
1.14
0.968
0.974
0.979
0.991
1.000
1.006
1.009
1.2
0.863
0.868
0.873
0.884
0.892
0.898
0.901
1.26
0.792
0.797
0.801
0.811
0.819
0.824
0.827
Calculating Power Dissipation
Quiescent Supply Current
Quiescent supply current (IDD) calculation depends on multiple factors, including operating voltages
(VCC, VCCI, and VJTAG), operating temperature, system clock frequency, and power mode usage.
Microsemi recommends using the Power Calculator and SmartPower software estimation tools to
evaluate the projected static and active power based on the user design, power mode usage, operating
voltage, and temperature.
Table 2-8 •
Power Supply State per Mode
Power Supply Configurations
Modes/Power Supplies
VCC
VCCPLL
VCCI
VJTAG
VPUMP
Flash*Freeze
On
On
On
On
On/off/floating
Sleep
Off
Off
On
Off
Off
Shutdown
Off
Off
Off
Off
Off
No Flash*Freeze
On
On
On
On
On/off/floating
Note: Off: Power Supply level = 0 V
Table 2-9 •
Quiescent Supply Current (IDD) Characteristics, IGLOO nano Flash*Freeze Mode*
Typical (25°C)
Core
Voltage
AGLN010
AGLN015
AGLN020
AGLN060
AGLN125
AGLN250
Units
1.2 V
1.9
3.3
3.3
8
13
20
µA
1.5 V
5.8
6
6
10
18
34
µA
Note: *IDD includes VCC, VPUMP, VCCI, VCCPLL, and VMV currents. Values do not include I/O static contribution,
which is shown in Table 2-13 on page 2-9 through Table 2-14 on page 2-9 and Table 2-15 on page 2-10
through Table 2-18 on page 2-11 (PDC6 and PDC7).
R ev i si o n 1 7
2 -7
IGLOO nano DC and Switching Characteristics
Table 2-10 • Quiescent Supply Current (IDD) Characteristics, IGLOO nano Sleep Mode*
Core
Voltage AGLN010 AGLN015 AGLN020 AGLN060 AGLN125 AGLN250 Units
VCCI= 1.2 V
Typical (25°C)
(per
bank)
1.2 V
1.7
1.7
1.7
1.7
1.7
1.7
µA
VCCI = 1.5 V (per bank) 1.2 V /
Typical (25°C)
1.5 V
1.8
1.8
1.8
1.8
1.8
1.8
µA
VCCI = 1.8 V (per bank) 1.2 V /
Typical (25°C)
1.5 V
1.9
1.9
1.9
1.9
1.9
1.9
µA
VCCI = 2.5 V (per bank) 1.2 V /
Typical (25°C)
1.5 V
2.2
2.2
2.2
2.2
2.2
2.2
µA
VCCI = 3.3 V (per bank) 1.2 V /
Typical (25°C)
1.5 V
2.5
2.5
2.5
2.5
2.5
2.5
µA
Note: *IDD = NBANKS * ICCI.
Table 2-11 • Quiescent Supply Current (IDD) Characteristics, IGLOO nano Shutdown Mode
Typical
(25°C)
Core Voltage
AGLN010
AGLN015
AGLN020
AGLN060
AGLN125
AGLN250
Units
1.2 V / 1.5 V
0
0
0
0
0
0
µA
Table 2-12 • Quiescent Supply Current (IDD), No IGLOO nano Flash*Freeze Mode1
Core
Voltage
ICCA Current
AGLN010 AGLN015 AGLN020 AGLN060 AGLN125 AGLN250 Units
2
Typical (25°C)
1.2 V
3.7
5
5
10
13
18
µA
1.5 V
8
14
14
20
28
44
µA
1.2 V
1.7
1.7
1.7
1.7
1.7
1.7
µA
VCCI / VJTAG = 1.5 V (per 1.2 V / 1.5 V
bank) Typical (25°C)
1.8
1.8
1.8
1.8
1.8
1.8
µA
VCCI / VJTAG = 1.8 V (per 1.2 V / 1.5 V
bank) Typical (25°C)
1.9
1.9
1.9
1.9
1.9
1.9
µA
VCCI / VJTAG = 2.5 V (per 1.2 V / 1.5 V
bank) Typical (25°C)
2.2
2.2
2.2
2.2
2.2
2.2
µA
VCCI / VJTAG = 3.3 V (per 1.2 V / 1.5 V
bank) Typical (25°C)
2.5
2.5
2.5
2.5
2.5
2.5
µA
ICCI or IJTAG Current
VCCI / VJTAG = 1.2 V (per
bank) Typical (25°C)
Notes:
1. IDD = NBANKS * ICCI + ICCA. JTAG counts as one bank when powered.
2. Includes VCC, VCCPLL, and VPUMP currents.
2- 8
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
Power per I/O Pin
Table 2-13 • Summary of I/O Input Buffer Power (per pin) – Default I/O Software Settings
Applicable to IGLOO nano I/O Banks
VCCI (V)
Dynamic Power
PAC9 (µW/MHz) 1
3.3 V LVTTL / 3.3 V LVCMOS
3.3
16.38
3.3 V LVTTL / 3.3 V LVCMOS – Schmitt Trigger
3.3
18.89
3.3
16.38
3.3 V LVCMOS Wide Range – Schmitt Trigger
3.3
18.89
2.5 V LVCMOS
2.5
4.71
2.5 V LVCMOS – Schmitt Trigger
2.5
6.13
1.8 V LVCMOS
1.8
1.64
1.8 V LVCMOS – Schmitt Trigger
1.8
1.79
1.5 V LVCMOS (JESD8-11)
1.5
0.97
1.5 V LVCMOS (JESD8-11) – Schmitt Trigger
1.5
0.96
1.2
0.57
1.2
0.52
1.2
0.57
1.2
0.52
Single-Ended
3.3 V LVCMOS Wide Range
2
3
1.2 V LVCMOS
1.2 V LVCMOS – Schmitt
Trigger3
1.2 V LVCMOS Wide Range3
1.2 V LVCMOS Wide Range – Schmitt Trigger
3
Notes:
1. PAC9 is the total dynamic power measured on VCCI.
2. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD8-B specification.
3. Applicable to IGLOO nano V2 devices operating at VCCI  VCC.
Table 2-14 • Summary of I/O Output Buffer Power (per pin) – Default I/O Software Settings1
Applicable to IGLOO nano I/O Banks
CLOAD (pF)
VCCI (V)
Dynamic Power
PAC10 (µW/MHz)2
3.3 V LVTTL / 3.3 V LVCMOS
5
3.3
107.98
3
5
3.3
107.98
2.5 V LVCMOS
5
2.5
61.24
1.8 V LVCMOS
5
1.8
31.28
1.5 V LVCMOS (JESD8-11)
5
1.5
21.50
5
1.2
15.22
Single-Ended
3.3 V LVCMOS Wide Range
1.2 V
LVCMOS4
Notes:
1.
2.
3.
4.
Dynamic power consumption is given for standard load and software default drive strength and output slew.
PAC10 is the total dynamic power measured on VCCI.
All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD8-B specification.
Applicable for IGLOO nano V2 devices operating at VCCI  VCC.
R ev i si o n 1 7
2 -9
IGLOO nano DC and Switching Characteristics
Power Consumption of Various Internal Resources
Table 2-15 • Different Components Contributing to Dynamic Power Consumption in IGLOO nano Devices
For IGLOO nano V2 or V5 Devices, 1.5 V Core Supply Voltage
Device Specific Dynamic Power (µW/MHz)
Parameter
Definition
AGLN250 AGLN125 AGLN060 AGLN020 AGLN015 AGLN010
PAC1
Clock contribution of a Global Rib
4.421
4.493
2.700
0
0
0
PAC2
Clock contribution of a Global Spine
2.704
1.976
1.982
4.002
4.002
2.633
PAC3
Clock contribution of a VersaTile row
1.496
1.504
1.511
1.346
1.346
1.340
PAC4
Clock contribution of a VersaTile
used as a sequential module
0.152
0.153
0.153
0.148
0.148
0.143
PAC5
First contribution of a VersaTile used
as a sequential module
0.057
PAC6
Second contribution of a VersaTile
used as a sequential module
0.207
PAC7
Contribution of a VersaTile used as
a combinatorial module
0.17
PAC8
Average contribution of a routing net
0.7
PAC9
Contribution of an I/O input pin
(standard-dependent)
See Table 2-13 on page 2-9.
PAC10
Contribution of an I/O output pin
(standard-dependent)
See Table 2-14.
PAC11
Average contribution of a RAM block
during a read operation
25.00
N/A
PAC12
Average contribution of a RAM block
during a write operation
30.00
N/A
PAC13
Dynamic contribution for PLL
2.70
N/A
Table 2-16 • Different Components Contributing to the Static Power Consumption in IGLOO nano Devices
For IGLOO nano V2 or V5 Devices, 1.5 V Core Supply Voltage
Device -Specific Static Power (mW)
Parameter
Definition
AGLN250 AGLN125 AGLN060 AGLN020 AGLN015 AGLN010
PDC1
Array static power in Active mode
See Table 2-12 on page 2-8
PDC2
Array static power in Static (Idle)
mode
See Table 2-12 on page 2-8
PDC3
Array static power in Flash*Freeze
mode
See Table 2-9 on page 2-7
PDC4 1
Static PLL contribution
PDC5
Bank quiescent power
(VCCI-dependent)2
1.84
N/A
See Table 2-12 on page 2-8
Notes:
1. Minimum contribution of the PLL when running at lowest frequency.
2. For a different output load, drive strength, or slew rate, Microsemi recommends using the Microsemi power spreadsheet
calculator or the SmartPower tool in Libero SoC.
2- 10
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Table 2-17 • Different Components Contributing to Dynamic Power Consumption in IGLOO nano Devices
For IGLOO nano V2 Devices, 1.2 V Core Supply Voltage
Device-Specific Dynamic Power (µW/MHz)
Parameter
Definition
AGLN250 AGLN125 AGLN060 AGLN020 AGLN015 AGLN010
PAC1
Clock contribution of a Global Rib
2.829
2.875
1.728
0
0
0
PAC2
Clock contribution of a Global Spine
1.731
1.265
1.268
2.562
2.562
1.685
PAC3
Clock contribution of a VersaTile row
0.957
0.963
0.967
0.862
0.862
0.858
PAC4
Clock contribution of a VersaTile used
as a sequential module
0.098
0.098
0.098
0.094
0.094
0.091
PAC5
First contribution of a VersaTile used
as a sequential module
0.045
PAC6
Second contribution of a VersaTile
used as a sequential module
0.186
PAC7
Contribution of a VersaTile used as a
combinatorial module
0.11
PAC8
Average contribution of a routing net
0.45
PAC9
Contribution of an I/O input pin
(standard-dependent)
See Table 2-13 on page 2-9
PAC10
Contribution of an I/O output pin
(standard-dependent)
See Table 2-14 on page 2-9
PAC11
Average contribution of a RAM block
during a read operation
25.00
N/A
PAC12
Average contribution of a RAM block
during a write operation
30.00
N/A
PAC13
Dynamic contribution for PLL
2.10
N/A
Table 2-18 • Different Components Contributing to the Static Power Consumption in IGLOO nano Devices
For IGLOO nano V2 Devices, 1.2 V Core Supply Voltage
Device-Specific Static Power (mW)
Parameter
Definition
AGLN250 AGLN125 AGLN060 AGLN020 AGLN015 AGLN010
PDC1
Array static power in Active mode
See Table 2-12 on page 2-8
PDC2
Array static power in Static (Idle)
mode
See Table 2-12 on page 2-8
PDC3
Array static power in Flash*Freeze
mode
See Table 2-9 on page 2-7
PDC4 1
Static PLL contribution
PDC5
Bank quiescent power
(VCCI-dependent)2
0.90
N/A
See Table 2-12 on page 2-8
Notes:
1. Minimum contribution of the PLL when running at lowest frequency.
2. For a different output load, drive strength, or slew rate, Microsemi recommends using the Microsemi power spreadsheet
calculator or the SmartPower tool in Libero SoC.
R ev i si o n 1 7
2- 11
IGLOO nano DC and Switching Characteristics
Power Calculation Methodology
This section describes a simplified method to estimate power consumption of an application. For more
accurate and detailed power estimations, use the SmartPower tool in Libero SoC software.
The power calculation methodology described below uses the following variables:
•
The number of PLLs as well as the number and the frequency of each output clock generated
•
The number of combinatorial and sequential cells used in the design
•
The internal clock frequencies
•
The number and the standard of I/O pins used in the design
•
The number of RAM blocks used in the design
•
Toggle rates of I/O pins as well as VersaTiles—guidelines are provided in Table 2-19 on
page 2-14.
•
Enable rates of output buffers—guidelines are provided for typical applications in Table 2-20 on
page 2-14.
•
Read rate and write rate to the memory—guidelines are provided for typical applications in
Table 2-20 on page 2-14. The calculation should be repeated for each clock domain defined in the
design.
Methodology
Total Power Consumption—PTOTAL
PTOTAL = PSTAT + PDYN
PSTAT is the total static power consumption.
PDYN is the total dynamic power consumption.
Total Static Power Consumption—PSTAT
PSTAT = (PDC1 or PDC2 or PDC3) + NBANKS * PDC5
NBANKS is the number of I/O banks powered in the design.
Total Dynamic Power Consumption—PDYN
PDYN = PCLOCK + PS-CELL + PC-CELL + PNET + PINPUTS + POUTPUTS + PMEMORY + PPLL
Global Clock Contribution—PCLOCK
PCLOCK = (PAC1 + NSPINE * PAC2 + NROW * PAC3 + NS-CELL* PAC4) * FCLK
NSPINE is the number of global spines used in the user design—guidelines are provided in
the "Spine Architecture" section of the IGLOO nano FPGA Fabric User's Guide.
NROW is the number of VersaTile rows used in the design—guidelines are provided in the
"Spine Architecture" section of the IGLOO nano FPGA Fabric User's Guide.
FCLK is the global clock signal frequency.
NS-CELL is the number of VersaTiles used as sequential modules in the design.
PAC1, PAC2, PAC3, and PAC4 are device-dependent.
Sequential Cells Contribution—PS-CELL
PS-CELL = NS-CELL * (PAC5 + 1 / 2 * PAC6) * FCLK
NS-CELL is the number of VersaTiles used as sequential modules in the design. When a
multi-tile sequential cell is used, it should be accounted for as 1.
1
is the toggle rate of VersaTile outputs—guidelines are provided in Table 2-19 on
page 2-14.
FCLK is the global clock signal frequency.
2- 12
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Combinatorial Cells Contribution—PC-CELL
PC-CELL = NC-CELL* 1 / 2 * PAC7 * FCLK
NC-CELL is the number of VersaTiles used as combinatorial modules in the design.
1
is the toggle rate of VersaTile outputs—guidelines are provided in Table 2-19 on
page 2-14.
FCLK is the global clock signal frequency.
Routing Net Contribution—PNET
PNET = (NS-CELL + NC-CELL) * 1 / 2 * PAC8 * FCLK
NS-CELL is the number of VersaTiles used as sequential modules in the design.
NC-CELL is the number of VersaTiles used as combinatorial modules in the design.
1
is the toggle rate of VersaTile outputs—guidelines are provided in Table 2-19 on
page 2-14.
FCLK is the global clock signal frequency.
I/O Input Buffer Contribution—PINPUTS
PINPUTS = NINPUTS * 2 / 2 * PAC9 * FCLK
NINPUTS is the number of I/O input buffers used in the design.
2 is the I/O buffer toggle rate—guidelines are provided in Table 2-19 on page 2-14.
FCLK is the global clock signal frequency.
I/O Output Buffer Contribution—POUTPUTS
POUTPUTS = NOUTPUTS * 2 / 2 * 1 * PAC10 * FCLK
NOUTPUTS is the number of I/O output buffers used in the design.
2 is the I/O buffer toggle rate—guidelines are provided in Table 2-19 on page 2-14.
1 is the I/O buffer enable rate—guidelines are provided in Table 2-20 on page 2-14.
FCLK is the global clock signal frequency.
RAM Contribution—PMEMORY
PMEMORY = PAC11 * NBLOCKS * FREAD-CLOCK * 2 + PAC12 * NBLOCK * FWRITE-CLOCK * 3
NBLOCKS is the number of RAM blocks used in the design.
FREAD-CLOCK is the memory read clock frequency.
2 is the RAM enable rate for read operations.
FWRITE-CLOCK is the memory write clock frequency.
3 is the RAM enable rate for write operations—guidelines are provided in Table 2-20 on
page 2-14.
PLL Contribution—PPLL
PPLL = PDC4 + PAC13 *FCLKOUT
FCLKOUT is the output clock frequency.1
1. If a PLL is used to generate more than one output clock, include each output clock in the formula by adding its corresponding
contribution (PAC13* FCLKOUT product) to the total PLL contribution.
R ev i si o n 1 7
2- 13
IGLOO nano DC and Switching Characteristics
Guidelines
Toggle Rate Definition
A toggle rate defines the frequency of a net or logic element relative to a clock. It is a percentage. If the
toggle rate of a net is 100%, this means that this net switches at half the clock frequency. Below are
some examples:
•
The average toggle rate of a shift register is 100% because all flip-flop outputs toggle at half of the
clock frequency.
•
The average toggle rate of an 8-bit counter is 25%:
–
Bit 0 (LSB) = 100%
–
Bit 1
= 50%
–
Bit 2
= 25%
–
…
–
Bit 7 (MSB) = 0.78125%
–
Average toggle rate = (100% + 50% + 25% + 12.5% + . . . + 0.78125%) / 8
Enable Rate Definition
Output enable rate is the average percentage of time during which tristate outputs are enabled. When
nontristate output buffers are used, the enable rate should be 100%.
Table 2-19 • Toggle Rate Guidelines Recommended for Power Calculation
Component
1
2
Definition
Guideline
Toggle rate of VersaTile outputs
10%
I/O buffer toggle rate
10%
Table 2-20 • Enable Rate Guidelines Recommended for Power Calculation
Component
1
2
3
2- 14
Definition
Guideline
I/O output buffer enable rate
100%
RAM enable rate for read operations
12.5%
RAM enable rate for write operations
12.5%
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
User I/O Characteristics
Timing Model
I/O Module
(Non-Registered)
Combinational Cell
Combinational Cell
Y
LVCMOS 2.5 V Output Drive
Strength = 8 mA High Slew Rate
Y
tPD = 1.18 ns
tPD = 0.90 ns
tDP = 1.99 ns
I/O Module
(Non-Registered)
Combinational Cell
Y
tDP = 2.35 ns
tPD = 1.60 ns
I/O Module
(Non-Registered)
Combinational Cell
I/O Module
(Registered)
Y
tPY = 1.06 ns
Input LVCMOS 2.5 V
D
LVTTL Output drive strength = 4 mA
High slew rate
tPD = 1.17 ns
Q
I/O Module
(Non-Registered)
Combinational Cell
Y
tICLKQ = 0.42 ns
tISUD = 0.47 ns
LVCMOS 1.5 V Output drive strength = 2 mA
High slew rate
tDP = 2.65 ns
tPD = 0.87 ns
Input LVTTL
Clock
Register Cell
tPY = 0.85 ns
D
Combinational Cell
Y
Q
I/O Module
(Non-Registered)
tPY = 1.15 ns
Figure 2-3 •
I/O Module
(Registered)
Register Cell
D
Q
D
tPD = 0.91 ns
tCLKQ = 0.89 ns
tSUD = 0.81 ns
LVCMOS 1.5 V
LVTTL Output drive strength = 8 mA
High slew rate
tDP = 1.96 ns
Q
tDP = 1.96 ns
tCLKQ = 0.89 ns
tSUD = 0.81 ns
Input LVTTL
Clock
Input LVTTL
Clock
tPY = 0.85 ns
tPY = 0.85 ns
LVTTL 3.3 V Output drive
strength = 8 mA High slew rate
tOCLKQ = 1.00 ns
tOSUD = 0.51 ns
Timing Model
Operating Conditions: STD Speed, Commercial Temperature Range (TJ = 70°C), Worst-Case
VCC = 1.425 V, for DC 1.5 V Core Voltage, Applicable to V2 and V5 Devices
R ev i si o n 1 7
2- 15
IGLOO nano DC and Switching Characteristics
tPY
tDIN
D
PAD
Q
DIN
Y
CLK
tPY = MAX(tPY(R), tPY(F))
tDIN = MAX(tDIN(R), tDIN(F))
To Array
I/O Interface
VIH
PAD
Vtrip
Vtrip
VIL
VCC
50%
50%
Y
GND
tPY
(F)
tPY
(R)
VCC
50%
DIN
GND
50%
tDIN
tDIN
(R)
Figure 2-4 •
2- 16
(F)
Input Buffer Timing Model and Delays (example)
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
tDOUT
tDP
D Q
D
PAD
DOUT
Std
Load
CLK
From Array
tDP = MAX(tDP(R), tDP(F))
tDOUT = MAX(tDOUT(R), tDOUT(F))
I/O Interface
tDOUT
(R)
D
50%
tDOUT
VCC
(F)
50%
0V
VCC
DOUT
50%
50%
0V
VOH
Vtrip
Vtrip
VOL
PAD
tDP
(R)
Figure 2-5 •
tDP
(F)
Output Buffer Model and Delays (example)
R ev i si o n 1 7
2- 17
IGLOO nano DC and Switching Characteristics
tEOUT
D
Q
CLK
E
tZL, tZH, tHZ, tLZ, tZLS, tZHS
EOUT
D
Q
PAD
DOUT
CLK
D
tEOUT = MAX(tEOUT(r), tEOUT(f))
I/O Interface
VCC
D
VCC
50%
tEOUT (F)
50%
E
tEOUT (R)
VCC
50%
EOUT
tZL
PAD
50%
50%
tHZ
Vtrip
tZH
VCCI
90% VCCI
Vtrip
VOL
VCC
D
VCC
E
50%
tEOUT (R)
50%
tEOUT (F)
VCC
EOUT
PAD
50%
tZLS
VOH
Vtrip
Figure 2-6 •
2- 18
50%
50%
tZHS
Vtrip
VOL
Tristate Output Buffer Timing Model and Delays (example)
R ev i sio n 1 7
50%
tLZ
10% VCCI
IGLOO nano Low Power Flash FPGAs
Overview of I/O Performance
Summary of I/O DC Input and Output Levels – Default I/O Software
Settings
Table 2-21 • Summary of Maximum and Minimum DC Input and Output Levels
Applicable to Commercial and Industrial Conditions—Software Default Settings
I/O Standard
3.3 V LVTTL /
3.3 V LVCMOS
Equivalent
Software
Default
Slew Min.
Drive
Drive
Strength Strength2 Rate V
VIH
VOL
VOH
IOL1 IOH1
mA mA
Max.
V
Min.
V
Max.
V
Max.
V
Min.
V
2.4
8 mA
High –0.3
0.8
2
3.6
0.4
3.3 V LVCMOS 100 µA
Wide Range3
8 mA
High –0.3
0.8
2
3.6
0.2
2.5 V LVCMOS
8 mA
8 mA
High –0.3
0.7
1.7
3.6
0.7
1.8 V LVCMOS
4 mA
4 mA
High –0.3 0.35 * VCCI 0.65 * VCCI 3.6
0.45
1.5 V LVCMOS
2 mA
2 mA
High –0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.25 * VCCI 0.75 * VCCI
2
2
1 mA
1 mA
High –0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.25 * VCCI 0.75 * VCCI
1
1
100 µA
1 mA
High –0.3 0.3 * VCCI 0.7 * VCCI 3.6
1.2 V
LVCMOS4
1.2 V LVCMOS
Wide Range4,5
8 mA
VIL
8
8
VCCI – 0.2 100 100
µA µA
1.7
8
8
VCCI – 0.45 4
4
0.1
VCCI – 0.1 100 100
µA µA
Notes:
1. Currents are measured at 85°C junction temperature.
2. The minimum drive strength for any LVCMOS 1.2 V or LVCMOS 3.3 V software configuration when run in wide range is
±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the
IBIS models.
3. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range, as specified in the JESD8-B specification.
4. Applicable to IGLOO nano V2 devices operating at VCCI VCC .
5. All LVCMOS 1.2 V software macros support LVCMOS 1.2 V wide range, as specified in the JESD8-12 specification.
Table 2-22 • Summary of Maximum and Minimum DC Input Levels
Applicable to Commercial and Industrial Conditions
Commercial1
DC I/O Standards
Industrial2
IIL 3
IIH 4
IIL 3
IIH 4
µA
µA
µA
µA
3.3 V LVTTL / 3.3 V LVCMOS
10
10
15
15
3.3 V LVCOMS Wide Range
10
10
15
15
2.5 V LVCMOS
10
10
15
15
1.8 V LVCMOS
10
10
15
15
1.5 V LVCMOS
10
10
15
15
1.2 V LVCMOS5
10
10
15
15
10
10
15
15
1.2 V LVCMOS Wide Range
5
Notes:
1. Commercial range (–20°C < TA < 70°C)
2. Industrial range (–40°C < TA < 85°C)
3. IIH is the input leakage current per I/O pin over recommended operating conditions, where VIH < VIN < VCCI. Input
current is larger when operating outside recommended ranges.
4. IIL is the input leakage current per I/O pin over recommended operating conditions, where –0.3 V < VIN < VIL.
5. Applicable to IGLOO nano V2 devices operating at VCCI VCC.
R ev i si o n 1 7
2- 19
IGLOO nano DC and Switching Characteristics
Summary of I/O Timing Characteristics – Default I/O Software Settings
Table 2-23 • Summary of AC Measuring Points
Standard
Measuring Trip Point (Vtrip)
3.3 V LVTTL / 3.3 V LVCMOS
1.4 V
3.3 V LVCMOS Wide Range
1.4 V
2.5 V LVCMOS
1.2 V
1.8 V LVCMOS
0.90 V
1.5 V LVCMOS
0.75 V
1.2 V LVCMOS
0.60 V
1.2 V LVCMOS Wide Range
0.60 V
Table 2-24 • I/O AC Parameter Definitions
Parameter
Parameter Definition
tDP
Data to Pad delay through the Output Buffer
tPY
Pad to Data delay through the Input Buffer
tDOUT
Data to Output Buffer delay through the I/O interface
tEOUT
Enable to Output Buffer Tristate Control delay through the I/O interface
tDIN
Input Buffer to Data delay through the I/O interface
tHZ
Enable to Pad delay through the Output Buffer—HIGH to Z
tZH
Enable to Pad delay through the Output Buffer—Z to HIGH
tLZ
Enable to Pad delay through the Output Buffer—LOW to Z
tZL
Enable to Pad delay through the Output Buffer—Z to LOW
tZHS
Enable to Pad delay through the Output Buffer with delayed enable—Z to HIGH
tZLS
Enable to Pad delay through the Output Buffer with delayed enable—Z to LOW
2- 20
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Applies to IGLOO nano at 1.5 V Core Operating Conditions
tZH
1.83
1.45 1.98 2.38
ns
3.3 V LVCMOS 100 µA 8 mA
Wide Range2
High
5 pF 0.97
2.56 0.19 1.20
1.66
0.66
2.57
2.02 2.82 3.31
ns
2.5 V LVCMOS
8 mA
8 mA
High
5 pF 0.97
1.81 0.19 1.10
1.24
0.66
1.85
1.63 1.97 2.26
ns
1.8 V LVCMOS
4 mA
4 mA
High
5 pF 0.97
2.08 0.19 1.03
1.44
0.66
2.12
1.95 1.99 2.19
ns
1.5 V LVCMOS
2 mA
2 mA
High
5 pF 0.97
2.39 0.19 1.19
1.52
0.66
2.44
2.24 2.02 2.15
ns
Units
tZL
0.66
tHZ
tE O U T
1.16
tLZ
tPYS
1.79 0.19 0.86
tPY
5 pF 0.97
tDIN
Capacitive Load (pF)
High
tDP
Slew Rate
8 mA
3.3 V LVTTL /
3.3 V LVCMOS
tDOUT
Equivalent Software Default
t Drive Strength Option1
8 mA
I/O Standard
Drive Strength (mA)
Table 2-25 • Summary of I/O Timing Characteristics—Software Default Settings
STD Speed Grade, Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V,
Worst-Case VCCI = 3.0 V
Notes:
1. The minimum drive strength for any LVCMOS 1.2 V or LVCMOS 3.3 V software configuration when run in wide range is
±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the
IBIS models.
2. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range, as specified in the JESD8-B specification.
3. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 21
IGLOO nano DC and Switching Characteristics
Applies to IGLOO nano at 1.2 V Core Operating Conditions
tZL
1.10
2.34 1.90 2.43 3.14 ns
3.3 V LVCMOS 100 µA 8 mA
Wide Range2
High
5 pF 1.55 3.25
0.26
1.31
1.91
1.10
3.25 2.61 3.38 4.27 ns
2.5 V LVCMOS
8 mA
8 mA
High
5 pF 1.55 2.30
0.26
1.21
1.39
1.10
2.33 2.04 2.41 2.99 ns
1.8 V LVCMOS
4 mA 4 mA
High
5 pF 1.55 2.49
0.26
1.13
1.59
1.10
2.53 2.34 2.42 2.81 ns
1.5 V LVCMOS
2 mA 2 mA
High
5 pF 1.55 2.78
0.26
1.27
1.77
1.10
2.82 2.62 2.44 2.74 ns
1.2 V LVCMOS
1 mA 1 mA
High
5 pF 1.55 3.50
0.26
1.56
2.27
1.10
3.37 3.10 2.55 2.66 ns
1.2 V LVCMOS 100 µA 1 mA
Wide Range3
High
5 pF 1.55 3.50
0.26
1.56
2.27
1.10
3.37 3.10 2.55 2.66 ns
Units
tEOUT
1.36
tHZ
tPYS
0.97
tLZ
tPY)
0.26
tZH
tDIN
5 pF 1.55 2.31
tDP
High
tDOUT
Slew Rate
8 mA
3.3 V LVTTL /
3.3 V LVCMOS
Capacitive Load (pF)
Equiv. Software Default
Drive Strength Option1
8 mA
I/O Standard
Drive Strength (mA)
Table 2-26 • Summary of I/O Timing Characteristics—Software Default Settings
STD Speed Grade, Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V,
Worst-Case VCCI = 3.0 V
Notes:
1. The minimum drive strength for any LVCMOS 1.2 V or LVCMOS 3.3 V software configuration when run in wide range is
±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to
the IBIS models..
2. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range, as specified in the JESD8-B specification.
3. All LVCMOS 1.2 V software macros support LVCMOS 1.2 V side range as specified in the JESD8-12 specification.
4. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
2- 22
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Detailed I/O DC Characteristics
Table 2-27 • Input Capacitance
Symbol
Definition
Conditions
Min.
Max.
Units
CIN
Input capacitance
VIN = 0, f = 1.0 MHz
8
pF
CINCLK
Input capacitance on the clock pin
VIN = 0, f = 1.0 MHz
8
pF
Drive Strength
RPULL-DOWN
()2
RPULL-UP
()3
2 mA
100
300
4 mA
100
300
6 mA
50
150
8 mA
50
150
Table 2-28 • I/O Output Buffer Maximum Resistances 1
Standard
3.3 V LVTTL / 3.3V LVCMOS
3.3 V LVCMOS Wide Range
2.5 V LVCMOS
1.8 V LVCMOS
1.5 V LVCMOS
1.2 V LVCMOS 4
1.2 V LVCMOS Wide
Range 4
100 µA
Same as equivalent software default drive
2 mA
100
200
4 mA
100
200
6 mA
50
100
8 mA
50
100
2 mA
200
225
4 mA
100
112
2 mA
200
224
1 mA
315
315
100 µA
315
315
Notes:
1. These maximum values are provided for informational reasons only. Minimum output buffer resistance values depend
on VCCI, drive strength selection, temperature, and process. For board design considerations and detailed output buffer
resistances, use the corresponding IBIS models posted at http://www.microsemi.com/soc/download/ibis/default.aspx.
2. R(PULL-DOWN-MAX) = (VOLspec) / IOLspec
3. R(PULL-UP-MAX) = (VCCImax – VOHspec) / IO H s p e c
4. Applicable to IGLOO nano V2 devices operating at VCCI  VCC.
R ev i si o n 1 7
2- 23
IGLOO nano DC and Switching Characteristics
Table 2-29 • I/O Weak Pull-Up/Pull-Down Resistances
Minimum and Maximum Weak Pull-Up/Pull-Down Resistance Values
R(WEAK PULL-UP)1 ()
R(WEAK PULL-DOWN)2 ()
VCCI
Min.
Max.
Min.
Max.
3.3 V
10 K
45 K
10 K
45 K
3.3 V (wide range I/Os)
10 K
45 K
10 K
45 K
2.5 V
11 K
55 K
12 K
74 K
1.8 V
18 K
70 K
17 K
110 K
1.5 V
19 K
90 K
19 K
140 K
1.2 V
25 K
110 K
25 K
150 K
1.2 V (wide range I/Os)
19 K
110 K
19 K
150 K
Notes:
1. R(WEAK PULL-UP-MAX) = (VCCImax – VOHspec) / I(WEAK PULL-UP-MIN)
2. R(WEAK PULL-DOWN-MAX) = (VOLspec) / I(WEAK PULL-DOWN-MIN)
Table 2-30 • I/O Short Currents IOSH/IOSL
3.3 V LVTTL / 3.3 V LVCMOS
3.3 V LVCMOS Wide Range
2.5 V LVCMOS
Drive Strength
IOSL (mA)*
IOSH (mA)*
2 mA
25
27
4 mA
25
27
6 mA
51
54
8 mA
51
54
100 µA
Same as equivalent software default drive
2 mA
16
18
4 mA
16
18
6 mA
32
37
8 mA
32
37
2 mA
9
11
4 mA
17
22
1.5 V LVCMOS
2 mA
13
16
1.2 V LVCMOS
1 mA
10
13
100 µA
10
13
1.8 V LVCMOS
1.2 V LVCMOS Wide Range
Note: *TJ = 100°C
2- 24
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
The length of time an I/O can withstand IOSH/IOSL events depends on the junction temperature. The
reliability data below is based on a 3.3 V, 8 mA I/O setting, which is the worst case for this type of
analysis.
For example, at 100°C, the short current condition would have to be sustained for more than six months
to cause a reliability concern. The I/O design does not contain any short circuit protection, but such
protection would only be needed in extremely prolonged stress conditions.
Table 2-31 • Duration of Short Circuit Event before Failure
Temperature
Time before Failure
–40°C
> 20 years
–20°C
> 20 years
0°C
> 20 years
25°C
> 20 years
70°C
5 years
85°C
2 years
100°C
6 months
Table 2-32 • Schmitt Trigger Input Hysteresis
Hysteresis Voltage Value (Typ.) for Schmitt Mode Input Buffers
Input Buffer Configuration
Hysteresis Value (typ.)
3.3 V LVTTL / LVCMOS (Schmitt trigger mode)
240 mV
2.5 V LVCMOS (Schmitt trigger mode)
140 mV
1.8 V LVCMOS (Schmitt trigger mode)
80 mV
1.5 V LVCMOS (Schmitt trigger mode)
60 mV
1.2 V LVCMOS (Schmitt trigger mode)
40 mV
Table 2-33 • I/O Input Rise Time, Fall Time, and Related I/O Reliability
Input Rise/Fall
Time (min.)
Input Rise/Fall Time
(max.)
Reliability
LVTTL/LVCMOS (Schmitt trigger
disabled)
No requirement
10 ns *
20 years (100°C)
LVTTL/LVCMOS (Schmitt trigger
enabled)
No requirement
No requirement, but
input noise voltage
cannot exceed Schmitt
hysteresis.
20 years (100°C)
Input Buffer
Note: *The maximum input rise/fall time is related to the noise induced into the input buffer trace. If the
noise is low, then the rise time and fall time of input buffers can be increased beyond the
maximum value. The longer the rise/fall times, the more susceptible the input signal is to the board
noise. Microsemi recommends signal integrity evaluation/characterization of the system to ensure
that there is no excessive noise coupling into input signals.
R ev i si o n 1 7
2- 25
IGLOO nano DC and Switching Characteristics
Single-Ended I/O Characteristics
3.3 V LVTTL / 3.3 V LVCMOS
Low-Voltage Transistor–Transistor Logic (LVTTL) is a general purpose standard (EIA/JESD) for 3.3 V
applications. It uses an LVTTL input buffer and push-pull output buffer.
Table 2-34 • Minimum and Maximum DC Input and Output Levels
3.3 V LVTTL /
3.3 V LVCMOS
VIL
VIH
VOL
VOH
IOL IOH
IOSL
IOSH
IIL 1 IIH 2
mA mA
Max.
mA3
Max.
mA3
µA4 µA4
Drive
Strength
Min.
V
Max.
V
Min.
V
Max.
V
Max.
V
Min.
V
2 mA
–0.3
0.8
2
3.6
0.4
2.4
2
2
25
27
10
10
4 mA
–0.3
0.8
2
3.6
0.4
2.4
4
4
25
27
10
10
6 mA
–0.3
0.8
2
3.6
0.4
2.4
6
6
51
54
10
10
8 mA
–0.3
0.8
2
3.6
0.4
2.4
8
8
51
54
10
10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operating conditions where –0.3 < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions where VIH < VIN < VCCI. Input
current is larger when operating outside recommended ranges.
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
R=1k
Test Point
Enable Path
Test Point
Datapath
Figure 2-7 •
5 pF
R to VCCI for tLZ / tZL / tZLS
R to GND for tHZ / tZH / tZHS
5 pF for tZH / tZHS / tZL / tZLS
5 pF for tHZ / tLZ
AC Loading
Table 2-35 • 3.3 V LVTTL/LVCMOS AC Waveforms, Measuring Points, and Capacitive Loads
Input LOW (V)
0
Input HIGH (V)
Measuring Point* (V)
CLOAD (pF)
3.3
1.4
5
Note: *Measuring point = Vtrip. See Table 2-23 on page 2-20 for a complete table of trip points.
2- 26
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Timing Characteristics
Applies to 1.5 V DC Core Voltage
Table 2-36 • 3.3 V LVTTL / 3.3 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 3.0 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
0.97
3.52
0.19
0.86
1.16
0.66
3.59
3.42
1.75
1.90
ns
4 mA
STD
0.97
3.52
0.19
0.86
1.16
0.66
3.59
3.42
1.75
1.90
ns
6 mA
STD
0.97
2.90
0.19
0.86
1.16
0.66
2.96
2.83
1.98
2.29
ns
8 mA
STD
0.97
2.90
0.19
0.86
1.16
0.66
2.96
2.83
1.98
2.29
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-37 • 3.3 V LVTTL / 3.3 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 3.0 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
0.97
2.16
0.19
0.86
1.16
0.66
2.20
1.80
1.75
1.99
ns
4 mA
STD
0.97
2.16
0.19
0.86
1.16
0.66
2.20
1.80
1.75
1.99
ns
6 mA
STD
0.97
1.79
0.19
0.86
1.16
0.66
1.83
1.45
1.98
2.38
ns
8 mA
STD
0.97
1.79
0.19
0.86
1.16
0.66
1.83
1.45
1.98
2.38
ns
Notes:
1. Software default selection highlighted in gray.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 27
IGLOO nano DC and Switching Characteristics
Applies to 1.2 V DC Core Voltage
Table 2-38 • 3.3 V LVTTL / 3.3 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 3.0 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
1.55
4.09
0.26
0.97
1.36
1.10
4.16
3.91
2.19
2.64
ns
4 mA
STD
1.55
4.09
0.26
0.97
1.36
1.10
4.16
3.91
2.19
2.64
ns
6 mA
STD
1.55
3.45
0.26
0.97
1.36
1.10
3.51
3.32
2.43
3.03
ns
8 mA
STD
1.55
3.45
0.26
0.97
1.36
1.10
3.51
3.32
2.43
3.03
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-39 • 3.3 V LVTTL / 3.3 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 3.0 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
1.55
2.68
0.26
0.97
1.36
1.10
2.72
2.26
2.19
2.74
ns
4 mA
STD
1.55
2.68
0.26
0.97
1.36
1.10
2.72
2.26
2.19
2.74
ns
6 mA
STD
1.55
2.31
0.26
0.97
1.36
1.10
2.34
1.90
2.43
3.14
ns
8 mA
STD
1.55
2.31
0.26
0.97
1.36
1.10
2.34
1.90
2.43
3.14
ns
Notes:
1. Software default selection highlighted in gray.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
2- 28
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
3.3 V LVCMOS Wide Range
Table 2-40 • Minimum and Maximum DC Input and Output Levels for LVCMOS 3.3 V Wide Range
3.3 V LVCMOS Equivalent
Wide Range1
Software
VIL
Default
Drive
Drive
Max.
Strength Min.
Strength
V
V
Option4
VIH
VOL
VOH
IOL
IOH
IIL 2 IIH 3
Min.
V
Max.
V
Max.
V
Min.
V
µA
µA
µA5
µA5
100 µA
2 mA
–0.3
0.8
2
3.6
0.2
VCCI – 0.2
100
100
10
10
100 µA
4 mA
–0.3
0.8
2
3.6
0.2
VCCI – 0.2
100
100
10
10
100 µA
6 mA
–0.3
0.8
2
3.6
0.2
VCCI – 0.2
100
100
10
10
100 µA
8 mA
–0.3
0.8
2
3.6
0.2
VCCI – 0.2
100
100
10
10
Notes:
1. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V Wide Range, as specified in the JEDEC JESD8-B
specification.
2. IIL is the input leakage current per I/O pin over recommended operating conditions where –0.3 < VIN < VIL.
3. IIH is the input leakage current per I/O pin over recommended operating conditions where VIH < VIN < VCCI. Input
current is larger when operating outside recommended ranges.
4. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive
strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models.
5. Currents are measured at 85°C junction temperature.
6. Software default selection is highlighted in gray.
R ev i si o n 1 7
2- 29
IGLOO nano DC and Switching Characteristics
Timing Characteristics
Applies to 1.5 V DC Core Voltage
Table 2-41 • 3.3 V LVCMOS Wide Range Low Slew – Applies to 1.5 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.7 V
Equivalent
Software
Default
Drive
Drive
Strength
Strength Option1
Speed
Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
100 µA
2 mA
STD
0.97
5.23
0.19
1.20
1.66
0.66
5.24
5.00
2.47
2.56
ns
100 µA
4 mA
STD
0.97
5.23
0.19
1.20
1.66
0.66
5.24
5.00
2.47
2.56
ns
100 µA
6 mA
STD
0.97
4.27
0.19
1.20
1.66
0.66
4.28
4.12
2.83
3.16
ns
100 µA
8 mA
STD
0.97
4.27
0.19
1.20
1.66
0.66
4.28
4.12
2.83
3.16
ns
Notes:
1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive
strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-42 • 3.3 V LVCMOS Wide Range High Slew – Applies to 1.5 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.7 V
Equivalent
Software
Default
Drive
Strength
Drive
Strength Option1
Speed
Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
100 µA
2 mA
STD
0.97
3.11
0.19
1.20
1.66
0.66
3.13
2.55
2.47
2.70
ns
100 µA
4 mA
STD
0.97
3.11
0.19
1.20
1.66
0.66
3.13
2.55
2.47
2.70
ns
100 µA
6 mA
STD
0.97
2.56
0.19
1.20
1.66
0.66
2.57
2.02
2.82
3.31
ns
100 µA
8 mA
STD
0.97
2.56
0.19
1.20
1.66
0.66
2.57
2.02
2.82
3.31
ns
Notes:
1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive
strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
3. Software default selection highlighted in gray.
2- 30
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Applies to 1.2 V DC Core Voltage
Table 2-43 • 3.3 V LVCMOS Wide Range Low Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.7 V
Equivalent
Software
Default
Drive
Drive
Strength
Strength Option1
Speed
Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
100 µA
2 mA
STD
1.55
6.01
0.26
1.31
1.91
1.10
6.01
5.66
3.02
3.49
ns
100 µA
4 mA
STD
1.55
6.01
0.26
1.31
1.91
1.10
6.01
5.66
3.02
3.49
ns
100 µA
6 mA
STD
1.55
5.02
0.26
1.31
1.91
1.10
5.02
4.76
3.38
4.10
ns
100 µA
8 mA
STD
1.55
5.02
0.26
1.31
1.91
1.10
5.02
4.76
3.38
4.10
ns
Notes:
1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive
strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-44 • 3.3 V LVCMOS Wide Range High Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.7 V
Equivalent
Software
Default
Drive
Strength
Drive
Strength Option1
Speed
Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
100 µA
2 mA
STD
1.55
3.82
0.26
1.31
1.91
1.10
3.82
3.15
3.01
3.65
ns
100 µA
4 mA
STD
1.55
3.82
0.26
1.31
1.91
1.10
3.82
3.15
3.01
3.65
ns
100 µA
6 mA
STD
1.55
3.25
0.26
1.31
1.91
1.10
3.25
2.61
3.38
4.27
ns
100 µA
8 mA
STD
1.55
3.25
0.26
1.31
1.91
1.10
3.25
2.61
3.38
4.27
ns
Notes:
1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive
strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
3. Software default selection highlighted in gray.
R ev i si o n 1 7
2- 31
IGLOO nano DC and Switching Characteristics
2.5 V LVCMOS
Low-Voltage CMOS for 2.5 V is an extension of the LVCMOS standard (JESD8-5) used for general
purpose 2.5 V applications.
Table 2-45 • Minimum and Maximum DC Input and Output Levels
2.5 V
LVCMOS
Drive
Strength
VIL
VIH
VOL
VOH
IOL IOH
Min., V Max., V Min., V Max., V Max., V Min., V mA mA
IOSL
Max., mA3
IIL 1 IIH 2
IOSH
Max., mA3 µA4 µA4
2 mA
–0.3
0.7
1.7
3.6
0.7
1.7
2
2
16
18
10
10
4 mA
–0.3
0.7
1.7
3.6
0.7
1.7
4
4
16
18
10
10
6 mA
–0.3
0.7
1.7
3.6
0.7
1.7
6
6
32
37
10
10
8 mA
–0.3
0.7
1.7
3.6
0.7
1.7
8
8
32
37
10
10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operating conditions where –0.3 < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions where VIH < VIN < VCCI. Input
current is larger when operating outside recommended ranges.
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
R=1k
Test Point
Enable Path
Test Point
Datapath
Figure 2-8 •
5 pF
R to VCCI for tLZ / tZL / tZLS
R to GND for tHZ / tZH / tZHS
5 pF for tZH / tZHS / tZL / tZLS
5 pF for tHZ / tLZ
AC Loading
Table 2-46 • 2.5 V LVCMOS AC Waveforms, Measuring Points, and Capacitive Loads
Input LOW (V)
0
Input HIGH (V)
Measuring Point* (V)
CLOAD (pF)
2.5
1.2
5
Note: *Measuring point = Vtrip. See Table 2-23 on page 2-20 for a complete table of trip points.
2- 32
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Timing Characteristics
Applies to 1.5 V DC Core Voltage
Table 2-47 • 2.5 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.3 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
0.97
4.13
0.19
1.10
1.24
0.66
4.01
4.13
1.73
1.74
ns
4 mA
STD
0.97
4.13
0.19
1.10
1.24
0.66
4.01
4.13
1.73
1.74
ns
8 mA
STD
0.97
3.39
0.19
1.10
1.24
0.66
3.31
3.39
1.98
2.19
ns
8 mA
STD
0.97
3.39
0.19
1.10
1.24
0.66
3.31
3.39
1.98
2.19
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-48 • 2.5 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.3 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
0.97
2.19
0.19
1.10
1.24
0.66
2.23
2.11
1.72
1.80
ns
4 mA
STD
0.97
2.19
0.19
1.10
1.24
0.66
2.23
2.11
1.72
1.80
ns
6 mA
STD
0.97
1.81
0.19
1.10
1.24
0.66
1.85
1.63
1.97
2.26
ns
8 mA
STD
0.97
1.81
0.19
1.10
1.24
0.66
1.85
1.63
1.97
2.26
ns
Notes:
1. Software default selection highlighted in gray.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 33
IGLOO nano DC and Switching Characteristics
Applies to 1.2 V DC Core Voltage
Table 2-49 • 2.5 LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.3 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
1.55
4.61
0.26
1.21
1.39
1.10
4.55
4.61
2.15
2.43
ns
4 mA
STD
1.55
4.61
0.26
1.21
1.39
1.10
4.55
4.61
2.15
2.43
ns
6 mA
STD
1.55
3.86
0.26
1.21
1.39
1.10
3.82
3.86
2.41
2.89
ns
8 mA
STD
1.55
3.86
0.26
1.21
1.39
1.10
3.82
3.86
2.41
2.89
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-50 • 2.5 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.3 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
1.55
2.68
0.26
1.21
1.39
1.10
2.72
2.54
2.15
2.51
ns
4 mA
STD
1.55
2.68
0.26
1.21
1.39
1.10
2.72
2.54
2.15
2.51
ns
6 mA
STD
1.55
2.30
0.26
1.21
1.39
1.10
2.33
2.04
2.41
2.99
ns
8 mA
STD
1.55
2.30
0.26
1.21
1.39
1.10
2.33
2.04
2.41
2.99
ns
Notes:
1. Software default selection highlighted in gray.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
2- 34
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
1.8 V LVCMOS
Low-voltage CMOS for 1.8 V is an extension of the LVCMOS standard (JESD8-5) used for general
purpose 1.8 V applications. It uses a 1.8 V input buffer and a push-pull output buffer.
Table 2-51 • Minimum and Maximum DC Input and Output Levels
1.8 V
LVCMOS
VIL
Max.
V
VOL
VOH
IOL IOH
IOSL
IOSH
IIL 1 IIH 2
Max.
V
Max.
V
Min.
V
mA mA
Max.
mA3
Max.
mA3
µA4 µA4
VIH
Drive
Strength
Min.
V
Min.
V
2 mA
–0.3 0.35 * VCCI 0.65 * VCCI
3.6
0.45
VCCI – 0.45
2
2
9
11
10
10
4 mA
–0.3 0.35 * VCCI 0.65 * VCCI
3.6
0.45
VCCI – 0.45
4
4
17
22
10
10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operating conditions where –0.3 < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions where VIH < VIN < VCCI. Input
current is larger when operating outside recommended ranges.
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
R=1k
Test Point
Enable Path
Test Point
Datapath
Figure 2-9 •
5 pF
R to VCCI for tLZ / tZL / tZLS
R to GND for tHZ / tZH / tZHS
5 pF for tZH / tZHS / tZL / tZLS
5 pF for tHZ / tLZ
AC Loading
Table 2-52 • 1.8 V LVCMOS AC Waveforms, Measuring Points, and Capacitive Loads
Input LOW (V)
0
Input HIGH (V)
Measuring Point* (V)
CLOAD (pF)
1.8
0.9
5
Note: *Measuring point = Vtrip. See Table 2-23 on page 2-20 for a complete table of trip points.
R ev i si o n 1 7
2- 35
IGLOO nano DC and Switching Characteristics
Timing Characteristics
Applies to 1.5 V DC Core Voltage
Table 2-53 • 1.8 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 1.7 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
0.97
5.44
0.19
1.03
1.44
0.66
5.25
5.44
1.69
1.35
ns
4 mA
STD
0.97
4.44
0.19
1.03
1.44
0.66
4.37
4.44
1.99
2.11
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-54 • 1.8 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 1.7 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
0.97
2.64
0.19
1.03
1.44
0.66
2.59
2.64
1.69
1.40
ns
4 mA
STD
0.97
2.08
0.19
1.03
1.44
0.66
2.12
1.95
1.99
2.19
ns
Notes:
1. Software default selection highlighted in gray.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Applies to 1.2 V DC Core Voltage
Table 2-55 • 1.8 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.7 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
1.55
5.92
0.26
1.13
1.59
1.10
5.72
5.92
2.11
1.95
ns
4 mA
STD
1.55
4.91
0.26
1.13
1.59
1.10
4.82
4.91
2.42
2.73
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-56 • 1.8 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.7 V
Drive Strength
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
2 mA
STD
1.55
3.05
0.26
1.13
1.59
1.10
3.01
3.05
2.10
2.00
ns
4 mA
STD
1.55
2.49
0.26
1.13
1.59
1.10
2.53
2.34
2.42
2.81
ns
Notes:
1. Software default selection highlighted in gray.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
2- 36
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
1.5 V LVCMOS (JESD8-11)
Low-Voltage CMOS for 1.5 V is an extension of the LVCMOS standard (JESD8-5) used for general
purpose 1.5 V applications. It uses a 1.5 V input buffer and a push-pull output buffer.
Table 2-57 • Minimum and Maximum DC Input and Output Levels
1.5 V
LVCMOS
VIL
Drive
Min.
Strength
V
2 mA
Max.
V
VIH
Min.
V
Max.
V
–0.3 0.35 * VCCI 0.65 * VCCI
3.6
VOL
VOH
IOL IOH IOSL
IOSH
IIL 1 IIH 2
Max.
V
Min.
V
mA mA
Max.
mA3
Max.
mA3
µA4 µA4
13
16
0.25 * VCCI 0.75 * VCCI
2
2
10
10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operating conditions where –0.3 < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions where VIH < VIN < VCCI. Input
current is larger when operating outside recommended ranges.
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
R=1k
Test Point
Enable Path
Test Point
Datapath
5 pF
R to VCCI for tLZ / tZL / tZLS
R to GND for tHZ / tZH / tZHS
5 pF for tZH / tZHS / tZL / tZLS
5 pF for tHZ / tLZ
Figure 2-10 • AC Loading
Table 2-58 • 1.5 V LVCMOS AC Waveforms, Measuring Points, and Capacitive Loads
Input LOW (V)
0
Input HIGH (V)
Measuring Point* (V)
CLOAD (pF)
1.5
0.75
5
Note: *Measuring point = Vtrip. See Table 2-23 on page 2-20 for a complete table of trip points.
R ev i si o n 1 7
2- 37
IGLOO nano DC and Switching Characteristics
Timing Characteristics
Applies to 1.5 V DC Core Voltage
Table 2-59 • 1.5 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 1.4 V
Drive Strength
2 mA
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
STD
0.97
5.39
0.19
1.19
1.62
0.66
5.48
5.39
2.02
2.06
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-60 • 1.5 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 1.4 V
Drive Strength
2 mA
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
STD
0.97
2.39
0.19
1.19
1.62
0.66
2.44
2.24
2.02
2.15
ns
Notes:
1. Software default selection highlighted in gray.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Applies to 1.2 V DC Core Voltage
Table 2-61 • 1.5 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.4 V
Drive Strength
2 mA
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
STD
1.55
5.87
0.26
1.27
1.77
1.10
5.92
5.87
2.45
2.65
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-62 • 1.5 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.4 V
Drive Strength
2 mA
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
STD
1.55
2.78
0.26
1.27
1.77
1.10
2.82
2.62
2.44
2.74
ns
Notes:
1. Software default selection highlighted in gray.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
2- 38
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
1.2 V LVCMOS (JESD8-12A)
Low-Voltage CMOS for 1.2 V complies with the LVCMOS standard JESD8-12A for general purpose 1.2 V
applications. It uses a 1.2 V input buffer and a push-pull output buffer.
Table 2-63 • Minimum and Maximum DC Input and Output Levels
1.2 V
LVCMOS
VIL
Drive
Min.
Strength
V
1 mA
VIH
Max.
V
Min.
V
–0.3 0.35 * VCCI 0.65 * VCCI
VOL
VOH
IOL IOH IOSL
Max.
V
Max.
V
Min.
V
mA mA
3.6
0.25 * VCCI
0.75 * VCCI
1
1
IOSH IIL 1 IIH 2
Max.
mA3
Max.
mA3
10
13
µA4 µA4
10
10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operating conditions where –0.3 < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions where VIH < VIN < VCCI. Input
current is larger when operating outside recommended ranges.
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Software default selection highlighted in gray.
Datapath
R to VCCI for tLZ / tZL / tZLS
R to GND for tHZ / tZH / tZHS
R=1k
Test Point
Enable Path
Test Point
5 pF
5 pF for tZH / tZHS / tZL / tZLS
5 pF for tHZ / tLZ
Figure 2-11 • AC Loading
Table 2-64 • 1.2 V LVCMOS AC Waveforms, Measuring Points, and Capacitive Loads
Input LOW (V)
Input HIGH (V)
Measuring Point* (V)
CLOAD (pF)
1.2
0.6
5
0
Note: *Measuring point = Vtrip. See Table 2-23 on page 2-20 for a complete table of trip points.
Timing Characteristics
Applies to 1.2 V DC Core Voltage
Table 2-65 • 1.2 V LVCMOS Low Slew
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.14 V
Drive Strength
1 mA
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
STD
1.55
8.30
0.26
1.56
2.27
1.10
7.97
7.54
2.56
2.55
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-66 • 1.2 V LVCMOS High Slew
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.14 V
Drive Strength
1 mA
Speed Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
STD
1.55
3.50
0.26
1.56
2.27
1.10
3.37
3.10
2.55
2.66
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 39
IGLOO nano DC and Switching Characteristics
1.2 V LVCMOS Wide Range
Table 2-67 • Minimum and Maximum DC Input and Output Levels
1.2 V
LVCMOS
Wide
Range
VIL
Drive
Min.
Strength
V
1 mA
VOL
VOH
IOL IOH
IOSL
IOSH
IIL 1 IIH 2
Max.
V
Max.
V
Min.
V
mA mA
Max.
mA3
Max.
mA3
µA4 µA4
3.6
0.1
10
13
VIH
Max.
V
Min.
V
–0.3 0.3 * VCCI 0.7 * VCCI
VCCI – 0.1 100 100
10
10
Notes:
1. IIL is the input leakage current per I/O pin over recommended operating conditions where –0.3 < VIN < VIL.
2. IIH is the input leakage current per I/O pin over recommended operating conditions where VIH < VIN < VCCI. Input
current is larger when operating outside recommended ranges.
3. Currents are measured at high temperature (100°C junction temperature) and maximum voltage.
4. Currents are measured at 85°C junction temperature.
5. Applicable to IGLOO nano V2 devices operating at VCCI VCC.
6. Software default selection highlighted in gray.
Timing Characteristics
Applies to 1.2 V DC Core Voltage
Table 2-68 • 1.2 V LVCMOS Wide Range Low Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.14 V
Equivalent
Software
Default
Drive
Strength
Drive
Strength Option1
100 µA
1 mA
Speed
Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
STD
1.55
8.30
0.26
1.56
2.27
1.10
7.97
7.54
2.56
2.55
ns
Notes:
1. The minimum drive strength for any LVCMOS 1.2 V software configuration when run in wide range is ±100 µA. Drive
strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-69 • 1.2 V LVCMOS Wide Range HIgh Slew – Applies to 1.2 V DC Core Voltage
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.14 V
Equivalent
Software
Default
Drive
Drive
Strength
Strength Option1
100 µA
1 mA
Speed
Grade
tDOUT
tDP
tDIN
tPY
tPYS
tEOUT
tZL
tZH
tLZ
tHZ
Units
STD
1.55
3.50
0.26
1.56
2.27
1.10
3.37
3.10
2.55
2.66
ns
Notes:
1. The minimum drive strength for any LVCMOS 1.2 V software configuration when run in wide range is ±100 µA. Drive
strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
3. Software default selection highlighted in gray.
2- 40
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
I/O Register Specifications
Fully Registered I/O Buffers with Asynchronous Preset
INBUF
Preset
L
DOUT
Data_out
C
D
Q
DFN1P1
E
Y
PRE
F
Core
Array
D
Q
DFN1P1
TRIBUF
PRE
INBUF
Data
Pad Out
D
EOUT
CLKBUF
CLK
H
I
A
PRE
J
D
Q
DFN1P1
Data Input I/O Register with:
Active High Preset
Positive-Edge Triggered
INBUF
D_Enable
CLK
CLKBUF
Data Output Register and
Enable Output Register with:
Active High Preset
Postive-Edge Triggered
Figure 2-12 • Timing Model of Registered I/O Buffers with Asynchronous Preset
R ev i si o n 1 7
2- 41
IGLOO nano DC and Switching Characteristics
Table 2-70 • Parameter Definition and Measuring Nodes
Parameter Name
Parameter Definition
Measuring Nodes
(from, to)*
tOCLKQ
Clock-to-Q of the Output Data Register
tOSUD
Data Setup Time for the Output Data Register
F, H
tOHD
Data Hold Time for the Output Data Register
F, H
tOPRE2Q
Asynchronous Preset-to-Q of the Output Data Register
tOREMPRE
Asynchronous Preset Removal Time for the Output Data Register
L, H
tORECPRE
Asynchronous Preset Recovery Time for the Output Data Register
L, H
tOECLKQ
Clock-to-Q of the Output Enable Register
tOESUD
Data Setup Time for the Output Enable Register
J, H
tOEHD
Data Hold Time for the Output Enable Register
J, H
tOEPRE2Q
Asynchronous Preset-to-Q of the Output Enable Register
tOEREMPRE
Asynchronous Preset Removal Time for the Output Enable Register
I, H
tOERECPRE
Asynchronous Preset Recovery Time for the Output Enable Register
I, H
tICLKQ
Clock-to-Q of the Input Data Register
A, E
tISUD
Data Setup Time for the Input Data Register
C, A
tIHD
Data Hold Time for the Input Data Register
C, A
tIPRE2Q
Asynchronous Preset-to-Q of the Input Data Register
D, E
tIREMPRE
Asynchronous Preset Removal Time for the Input Data Register
D, A
tIRECPRE
Asynchronous Preset Recovery Time for the Input Data Register
D, A
Note: *See Figure 2-12 on page 2-41 for more information.
2- 42
R ev i sio n 1 7
H, DOUT
L, DOUT
H, EOUT
I, EOUT
IGLOO nano Low Power Flash FPGAs
Fully Registered I/O Buffers with Asynchronous Clear
D
CC
Q
DFN1C1
EE
Data_out FF
D
Q
DFN1C1
TRIBUF
INBUF
Data
Core
Array
Pad Out
DOUT
Y
EOUT
CLR
CLR
LL
INBUF
CLR
CLKBUF
CLK
HH
AA
JJ
DD
D
Q
DFN1C1
Data Input I/O Register with
Active High Clear
Positive-Edge Triggered
INBUF
CLKBUF
D_Enable
CLK
CLR
Data Output Register and
Enable Output Register with
Active High Clear
Positive-Edge Triggered
Figure 2-13 • Timing Model of the Registered I/O Buffers with Asynchronous Clear
R ev i si o n 1 7
2- 43
IGLOO nano DC and Switching Characteristics
Table 2-71 • Parameter Definition and Measuring Nodes
Parameter Name
Parameter Definition
Measuring Nodes
(from, to)*
tOCLKQ
Clock-to-Q of the Output Data Register
tOSUD
Data Setup Time for the Output Data Register
FF, HH
tOHD
Data Hold Time for the Output Data Register
FF, HH
tOCLR2Q
Asynchronous Clear-to-Q of the Output Data Register
tOREMCLR
Asynchronous Clear Removal Time for the Output Data Register
LL, HH
tORECCLR
Asynchronous Clear Recovery Time for the Output Data Register
LL, HH
tOECLKQ
Clock-to-Q of the Output Enable Register
tOESUD
Data Setup Time for the Output Enable Register
JJ, HH
tOEHD
Data Hold Time for the Output Enable Register
JJ, HH
tOECLR2Q
Asynchronous Clear-to-Q of the Output Enable Register
tOEREMCLR
Asynchronous Clear Removal Time for the Output Enable Register
II, HH
tOERECCLR
Asynchronous Clear Recovery Time for the Output Enable Register
II, HH
tICLKQ
Clock-to-Q of the Input Data Register
AA, EE
tISUD
Data Setup Time for the Input Data Register
CC, AA
tIHD
Data Hold Time for the Input Data Register
CC, AA
tICLR2Q
Asynchronous Clear-to-Q of the Input Data Register
DD, EE
tIREMCLR
Asynchronous Clear Removal Time for the Input Data Register
DD, AA
tIRECCLR
Asynchronous Clear Recovery Time for the Input Data Register
DD, AA
Note: *See Figure 2-13 on page 2-43 for more information.
2- 44
R ev i sio n 1 7
HH, DOUT
LL, DOUT
HH, EOUT
II, EOUT
IGLOO nano Low Power Flash FPGAs
Input Register
tICKMPWH tICKMPWL
CLK
50%
50%
1
50%
50%
50%
0
tIWPRE
Preset
50%
50%
tIHD
tISUD
Data
50%
50%
tIRECPRE
tIREMPRE
50%
50%
50%
tIWCLR
50%
Clear
tIRECCLR
tIREMCLR
50%
50%
tIPRE2Q
50%
Out_1
50%
tICLR2Q
50%
tICLKQ
Figure 2-14 • Input Register Timing Diagram
Timing Characteristics
1.5 V DC Core Voltage
Table 2-72 • Input Data Register Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V
Parameter
Description
Std.
Units
tICLKQ
Clock-to-Q of the Input Data Register
0.42
ns
tISUD
Data Setup Time for the Input Data Register
0.47
ns
tIHD
Data Hold Time for the Input Data Register
0.00
ns
tICLR2Q
Asynchronous Clear-to-Q of the Input Data Register
0.79
ns
tIPRE2Q
Asynchronous Preset-to-Q of the Input Data Register
0.79
ns
tIREMCLR
Asynchronous Clear Removal Time for the Input Data Register
0.00
ns
tIRECCLR
Asynchronous Clear Recovery Time for the Input Data Register
0.24
ns
tIREMPRE
Asynchronous Preset Removal Time for the Input Data Register
0.00
ns
tIRECPRE
Asynchronous Preset Recovery Time for the Input Data Register
0.24
ns
tIWCLR
Asynchronous Clear Minimum Pulse Width for the Input Data Register
0.19
ns
tIWPRE
Asynchronous Preset Minimum Pulse Width for the Input Data Register
0.19
ns
tICKMPWH
Clock Minimum Pulse Width HIGH for the Input Data Register
0.31
ns
tICKMPWL
Clock Minimum Pulse Width LOW for the Input Data Register
0.28
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 45
IGLOO nano DC and Switching Characteristics
1.2 V DC Core Voltage
Table 2-73 • Input Data Register Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V
Parameter
Description
Std.
Units
tICLKQ
Clock-to-Q of the Input Data Register
0.68
ns
tISUD
Data Setup Time for the Input Data Register
0.97
ns
tIHD
Data Hold Time for the Input Data Register
0.00
ns
tICLR2Q
Asynchronous Clear-to-Q of the Input Data Register
1.19
ns
tIPRE2Q
Asynchronous Preset-to-Q of the Input Data Register
1.19
ns
tIREMCLR
Asynchronous Clear Removal Time for the Input Data Register
0.00
ns
tIRECCLR
Asynchronous Clear Recovery Time for the Input Data Register
0.24
ns
tIREMPRE
Asynchronous Preset Removal Time for the Input Data Register
0.00
ns
tIRECPRE
Asynchronous Preset Recovery Time for the Input Data Register
0.24
ns
tIWCLR
Asynchronous Clear Minimum Pulse Width for the Input Data Register
0.19
ns
tIWPRE
Asynchronous Preset Minimum Pulse Width for the Input Data Register
0.19
ns
tICKMPWH
Clock Minimum Pulse Width HIGH for the Input Data Register
0.31
ns
tICKMPWL
Clock Minimum Pulse Width LOW for the Input Data Register
0.28
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
2- 46
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Output Register
tOCKMPWH tOCKMPWL
CLK
50%
50%
50%
50%
50%
50%
50%
tOSUD tOHD
Data_out
1
50%
50%
0
tOWPRE
Preset
tOREMPRE
tORECPRE
50%
50%
50%
tOWCLR
50%
Clear
tORECCLR
tOREMCLR
50%
50%
tOPRE2Q
50%
DOUT
50%
tOCLR2Q
50%
tOCLKQ
Figure 2-15 • Output Register Timing Diagram
Timing Characteristics
1.5 V DC Core Voltage
Table 2-74 • Output Data Register Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V
Parameter
Description
Std.
Units
tOCLKQ
Clock-to-Q of the Output Data Register
1.00
ns
tOSUD
Data Setup Time for the Output Data Register
0.51
ns
tOHD
Data Hold Time for the Output Data Register
0.00
ns
tOCLR2Q
Asynchronous Clear-to-Q of the Output Data Register
1.34
ns
tOPRE2Q
Asynchronous Preset-to-Q of the Output Data Register
1.34
ns
tOREMCLR
Asynchronous Clear Removal Time for the Output Data Register
0.00
ns
tORECCLR
Asynchronous Clear Recovery Time for the Output Data Register
0.24
ns
tOREMPRE
Asynchronous Preset Removal Time for the Output Data Register
0.00
ns
tORECPRE
Asynchronous Preset Recovery Time for the Output Data Register
0.24
ns
tOWCLR
Asynchronous Clear Minimum Pulse Width for the Output Data Register
0.19
ns
tOWPRE
Asynchronous Preset Minimum Pulse Width for the Output Data Register
0.19
ns
tOCKMPWH
Clock Minimum Pulse Width HIGH for the Output Data Register
0.31
ns
tOCKMPWL
Clock Minimum Pulse Width LOW for the Output Data Register
0.28
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 47
IGLOO nano DC and Switching Characteristics
1.2 V DC Core Voltage
Table 2-75 • Output Data Register Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V
Parameter
Description
Std.
Units
tOCLKQ
Clock-to-Q of the Output Data Register
1.52
ns
tOSUD
Data Setup Time for the Output Data Register
1.15
ns
tOHD
Data Hold Time for the Output Data Register
0.00
ns
tOCLR2Q
Asynchronous Clear-to-Q of the Output Data Register
1.96
ns
tOPRE2Q
Asynchronous Preset-to-Q of the Output Data Register
1.96
ns
tOREMCLR
Asynchronous Clear Removal Time for the Output Data Register
0.00
ns
tORECCLR
Asynchronous Clear Recovery Time for the Output Data Register
0.24
ns
tOREMPRE
Asynchronous Preset Removal Time for the Output Data Register
0.00
ns
tORECPRE
Asynchronous Preset Recovery Time for the Output Data Register
0.24
ns
tOWCLR
Asynchronous Clear Minimum Pulse Width for the Output Data Register
0.19
ns
tOWPRE
Asynchronous Preset Minimum Pulse Width for the Output Data Register
0.19
ns
tOCKMPWH
Clock Minimum Pulse Width HIGH for the Output Data Register
0.31
ns
tOCKMPWL
Clock Minimum Pulse Width LOW for the Output Data Register
0.28
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
2- 48
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Output Enable Register
tOECKMPWH tOECKMPWL
CLK
50%
50%
50%
50%
50%
50%
50%
tOESUD tOEHD
D_Enable
1
50%
0 50%
tOEWPRE
tOEREMPRE
tOERECPRE
50%
50%
50%
Preset
tOEWCLR
50%
Clear
tOEPRE2Q
EOUT
50%
50%
tOERECCLR
tOEREMCLR
50%
50%
tOECLR2Q
50%
tOECLKQ
Figure 2-16 • Output Enable Register Timing Diagram
Timing Characteristics
1.5 V DC Core Voltage
Table 2-76 • Output Enable Register Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V
Parameter
Description
Std.
Units
tOECLKQ
Clock-to-Q of the Output Enable Register
0.75
ns
tOESUD
Data Setup Time for the Output Enable Register
0.51
ns
tOEHD
Data Hold Time for the Output Enable Register
0.00
ns
tOECLR2Q
Asynchronous Clear-to-Q of the Output Enable Register
1.13
ns
tOEPRE2Q
Asynchronous Preset-to-Q of the Output Enable Register
1.13
ns
tOEREMCLR
Asynchronous Clear Removal Time for the Output Enable Register
0.00
ns
tOERECCLR
Asynchronous Clear Recovery Time for the Output Enable Register
0.24
ns
tOEREMPRE
Asynchronous Preset Removal Time for the Output Enable Register
0.00
ns
tOERECPRE
Asynchronous Preset Recovery Time for the Output Enable Register
0.24
ns
tOEWCLR
Asynchronous Clear Minimum Pulse Width for the Output Enable Register
0.19
ns
tOEWPRE
Asynchronous Preset Minimum Pulse Width for the Output Enable Register
0.19
ns
tOECKMPWH
Clock Minimum Pulse Width HIGH for the Output Enable Register
0.31
ns
tOECKMPWL
Clock Minimum Pulse Width LOW for the Output Enable Register
0.28
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 49
IGLOO nano DC and Switching Characteristics
1.2 V DC Core Voltage
Table 2-77 • Output Enable Register Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V
Parameter
Description
Std.
Units
1.10
ns
tOECLKQ
Clock-to-Q of the Output Enable Register
tOESUD
Data Setup Time for the Output Enable Register
1.15
ns
tOEHD
Data Hold Time for the Output Enable Register
0.00
ns
tOECLR2Q
Asynchronous Clear-to-Q of the Output Enable Register
1.65
ns
tOEPRE2Q
Asynchronous Preset-to-Q of the Output Enable Register
1.65
ns
tOEREMCLR
Asynchronous Clear Removal Time for the Output Enable Register
0.00
ns
tOERECCLR
Asynchronous Clear Recovery Time for the Output Enable Register
0.24
ns
tOEREMPRE
Asynchronous Preset Removal Time for the Output Enable Register
0.00
ns
tOERECPRE
Asynchronous Preset Recovery Time for the Output Enable Register
0.24
ns
tOEWCLR
Asynchronous Clear Minimum Pulse Width for the Output Enable Register
0.19
ns
tOEWPRE
Asynchronous Preset Minimum Pulse Width for the Output Enable Register
0.19
ns
tOECKMPWH
Clock Minimum Pulse Width HIGH for the Output Enable Register
0.31
ns
tOECKMPWL
Clock Minimum Pulse Width LOW for the Output Enable Register
0.28
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
2- 50
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
DDR Module Specifications
Note: DDR is not supported for AGLN010, AGLN015, and AGLN020 devices.
Input DDR Module
Input DDR
INBUF
Data
A
D
Out_QF
(to core)
E
Out_QR
(to core)
FF1
B
CLK
CLKBUF
FF2
C
CLR
INBUF
DDR_IN
Figure 2-17 • Input DDR Timing Model
Table 2-78 • Parameter Definitions
Parameter Name
Parameter Definition
Measuring Nodes (from, to)
tDDRICLKQ1
Clock-to-Out Out_QR
B, D
tDDRICLKQ2
Clock-to-Out Out_QF
B, E
tDDRISUD
Data Setup Time of DDR input
A, B
tDDRIHD
Data Hold Time of DDR input
A, B
tDDRICLR2Q1
Clear-to-Out Out_QR
C, D
tDDRICLR2Q2
Clear-to-Out Out_QF
C, E
tDDRIREMCLR
Clear Removal
C, B
tDDRIRECCLR
Clear Recovery
C, B
R ev i si o n 1 7
2- 51
IGLOO nano DC and Switching Characteristics
CLK
tDDRISUD
Data
1
2
3
4
5
6
tDDRIHD
7
8
9
tDDRIRECCLR
CLR
tDDRIREMCLR
tDDRICLKQ1
tDDRICLR2Q1
Out_QF
2
6
4
tDDRICLKQ2
tDDRICLR2Q2
Out_QR
3
5
7
Figure 2-18 • Input DDR Timing Diagram
Timing Characteristics
1.5 V DC Core Voltage
Table 2-79 • Input DDR Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.25 V
Parameter
Description
Std.
Units
tDDRICLKQ1
Clock-to-Out Out_QR for Input DDR
0.48
ns
tDDRICLKQ2
Clock-to-Out Out_QF for Input DDR
0.65
ns
tDDRISUD1
Data Setup for Input DDR (negedge)
0.50
ns
tDDRISUD2
Data Setup for Input DDR (posedge)
0.40
ns
tDDRIHD1
Data Hold for Input DDR (negedge)
0.00
ns
tDDRIHD2
Data Hold for Input DDR (posedge)
0.00
ns
tDDRICLR2Q1
Asynchronous Clear-to-Out Out_QR for Input DDR
0.82
ns
tDDRICLR2Q2
Asynchronous Clear-to-Out Out_QF for Input DDR
0.98
ns
tDDRIREMCLR
Asynchronous Clear Removal Time for Input DDR
0.00
ns
tDDRIRECCLR
Asynchronous Clear Recovery Time for Input DDR
0.23
ns
tDDRIWCLR
Asynchronous Clear Minimum Pulse Width for Input DDR
0.19
ns
tDDRICKMPWH
Clock Minimum Pulse Width HIGH for Input DDR
0.31
ns
tDDRICKMPWL
Clock Minimum Pulse Width LOW for Input DDR
0.28
ns
FDDRIMAX
Maximum Frequency for Input DDR
250.00
MHz
Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
2- 52
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
1.2 V DC Core Voltage
Table 2-80 • Input DDR Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V
Parameter
Description
Std.
Units
tDDRICLKQ1
Clock-to-Out Out_QR for Input DDR
0.76
ns
tDDRICLKQ2
Clock-to-Out Out_QF for Input DDR
0.94
ns
tDDRISUD1
Data Setup for Input DDR (negedge)
0.93
ns
tDDRISUD2
Data Setup for Input DDR (posedge)
0.84
ns
tDDRIHD1
Data Hold for Input DDR (negedge)
0.00
ns
tDDRIHD2
Data Hold for Input DDR (posedge)
0.00
ns
tDDRICLR2Q1
Asynchronous Clear-to-Out Out_QR for Input DDR
1.23
ns
tDDRICLR2Q2
Asynchronous Clear-to-Out Out_QF for Input DDR
1.42
ns
tDDRIREMCLR
Asynchronous Clear Removal Time for Input DDR
0.00
ns
tDDRIRECCLR
Asynchronous Clear Recovery Time for Input DDR
0.24
ns
tDDRIWCLR
Asynchronous Clear Minimum Pulse Width for Input DDR
0.19
ns
tDDRICKMPWH
Clock Minimum Pulse Width HIGH for Input DDR
0.31
ns
tDDRICKMPWL
Clock Minimum Pulse Width LOW for Input DDR
0.28
ns
FDDRIMAX
Maximum Frequency for Input DDR
160.00
MHz
Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
R ev i si o n 1 7
2- 53
IGLOO nano DC and Switching Characteristics
Output DDR Module
Output DDR
A
Data_F
(from core)
X
FF1
B
CLK
CLKBUF
E
X
C
X
D
Data_R
(from core)
Out
0
X
1
X
OUTBUF
FF2
B
X
CLR
INBUF
C
X
DDR_OUT
Figure 2-19 • Output DDR Timing Model
Table 2-81 • Parameter Definitions
Parameter Name
Parameter Definition
Measuring Nodes (from, to)
tDDROCLKQ
Clock-to-Out
B, E
tDDROCLR2Q
Asynchronous Clear-to-Out
C, E
tDDROREMCLR
Clear Removal
C, B
tDDRORECCLR
Clear Recovery
C, B
tDDROSUD1
Data Setup Data_F
A, B
tDDROSUD2
Data Setup Data_R
D, B
tDDROHD1
Data Hold Data_F
A, B
tDDROHD2
Data Hold Data_R
D, B
2- 54
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
CLK
tDDROSUD2 tDDROHD2
1
Data_F
2
5
tDDROHD1
tDDROREMCLR
Data_R 6
4
3
7
8
9
10
11
tDDRORECCLR
tDDROREMCLR
CLR
tDDROCLR2Q
tDDROCLKQ
Out
7
2
8
3
9
4
10
Figure 2-20 • Output DDR Timing Diagram
Timing Characteristics
1.5 V DC Core Voltage
Table 2-82 • Output DDR Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V
Parameter
Description
Std.
Units
tDDROCLKQ
Clock-to-Out of DDR for Output DDR
1.07
ns
tDDROSUD1
Data_F Data Setup for Output DDR
0.67
ns
tDDROSUD2
Data_R Data Setup for Output DDR
0.67
ns
tDDROHD1
Data_F Data Hold for Output DDR
0.00
ns
tDDROHD2
Data_R Data Hold for Output DDR
0.00
ns
tDDROCLR2Q
Asynchronous Clear-to-Out for Output DDR
1.38
ns
tDDROREMCLR
Asynchronous Clear Removal Time for Output DDR
0.00
ns
tDDRORECCLR
Asynchronous Clear Recovery Time for Output DDR
0.23
ns
tDDROWCLR1
Asynchronous Clear Minimum Pulse Width for Output DDR
0.19
ns
tDDROCKMPWH
Clock Minimum Pulse Width HIGH for the Output DDR
0.31
ns
tDDROCKMPWL
Clock Minimum Pulse Width LOW for the Output DDR
0.28
ns
FDDOMAX
Maximum Frequency for the Output DDR
250.00
MHz
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 55
IGLOO nano DC and Switching Characteristics
1.2 V DC Core Voltage
Table 2-83 • Output DDR Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V
Parameter
Description
Std.
Units
tDDROCLKQ
Clock-to-Out of DDR for Output DDR
1.60
ns
tDDROSUD1
Data_F Data Setup for Output DDR
1.09
ns
tDDROSUD2
Data_R Data Setup for Output DDR
1.16
ns
tDDROHD1
Data_F Data Hold for Output DDR
0.00
ns
tDDROHD2
Data_R Data Hold for Output DDR
0.00
ns
tDDROCLR2Q
Asynchronous Clear-to-Out for Output DDR
1.99
ns
tDDROREMCLR
Asynchronous Clear Removal Time for Output DDR
0.00
ns
tDDRORECCLR
Asynchronous Clear Recovery Time for Output DDR
0.24
ns
tDDROWCLR1
Asynchronous Clear Minimum Pulse Width for Output DDR
0.19
ns
tDDROCKMPWH
Clock Minimum Pulse Width HIGH for the Output DDR
0.31
ns
tDDROCKMPWL
Clock Minimum Pulse Width LOW for the Output DDR
0.28
ns
FDDOMAX
Maximum Frequency for the Output DDR
160.00
MHz
Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
2- 56
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
VersaTile Characteristics
VersaTile Specifications as a Combinatorial Module
The IGLOO nano library offers all combinations of LUT-3 combinatorial functions. In this section, timing
characteristics are presented for a sample of the library. For more details, refer to the Fusion, IGLOO/e,
and ProASIC3/ E Macro Library Guide.
A
A
B
A
OR2
Y
AND2
A
Y
B
B
B
XOR2
A
B
C
Y
A
A
B
C
NOR2
B
A
A
Y
INV
NAND3
A
MAJ3
B
Y
NAND2
XOR3
Y
Y
0
MUX2
B
Y
Y
1
C
S
Figure 2-21 • Sample of Combinatorial Cells
R ev i si o n 1 7
2- 57
IGLOO nano DC and Switching Characteristics
tPD
Fanout = 4
A
Net
NAND2 or Any
Combinatorial
Logic
Length = 1 VersaTile
B
A
Net
Length = 1 VersaTile
B
Y
NAND2 or Any
Combinatorial
Logic
tPD = MAX(tPD(RR), tPD(RF),
tPD(FF), tPD(FR)) where edges are
applicable for a particular
combinatorial cell
A
Net
Length = 1 VersaTile
B
Y
NAND2 or Any
Combinatorial
Logic
A
Net
Length = 1 VersaTile
B
Y
NAND2 or Any
Combinatorial
Logic
VCC
50%
50%
A, B, C
GND
VCC
50%
50%
OUT
GND
VCC
tPD
tPD
(FF)
(RR)
tPD
OUT
(FR)
50%
tPD
(RF)
GND
Figure 2-22 • Timing Model and Waveforms
2- 58
R ev i sio n 1 7
Y
50%
IGLOO nano Low Power Flash FPGAs
Timing Characteristics
1.5 V DC Core Voltage
Table 2-84 • Combinatorial Cell Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V
Combinatorial Cell
Equation
Parameter
Std.
Units
Y = !A
tPD
0.76
ns
Y=A·B
tPD
0.87
ns
Y = !(A · B)
tPD
0.91
ns
Y=A+B
tPD
0.90
ns
NOR2
Y = !(A + B)
tPD
0.94
ns
XOR2
Y = A B
tPD
1.39
ns
MAJ3
Y = MAJ(A, B, C)
tPD
1.44
ns
XOR3
Y = A  B C
tPD
1.60
ns
MUX2
Y = A !S + B S
tPD
1.17
ns
AND3
Y=A·B·C
tPD
1.18
ns
INV
AND2
NAND2
OR2
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
1.2 V DC Core Voltage
Table 2-85 • Combinatorial Cell Propagation Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V
Combinatorial Cell
Equation
Parameter
Std.
Units
Y = !A
tPD
1.33
ns
Y=A·B
tPD
1.48
ns
Y = !(A · B)
tPD
1.58
ns
Y=A+B
tPD
1.53
ns
NOR2
Y = !(A + B)
tPD
1.63
ns
XOR2
Y = A B
tPD
2.34
ns
MAJ3
Y = MAJ(A, B, C)
tPD
2.59
ns
XOR3
Y = A  B C
tPD
2.74
ns
MUX2
Y = A !S + B S
tPD
2.03
ns
AND3
Y=A·B·C
tPD
2.11
ns
INV
AND2
NAND2
OR2
Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
R ev i si o n 1 7
2- 59
IGLOO nano DC and Switching Characteristics
VersaTile Specifications as a Sequential Module
The IGLOO nano library offers a wide variety of sequential cells, including flip-flops and latches. Each
has a data input and optional enable, clear, or preset. In this section, timing characteristics are presented
for a representative sample from the library. For more details, refer to the Fusion, IGLOO/e, and
ProASIC3/E Macro Library Guide.
Data
D
Q
Out
Data
En
DFN1
CLK
D
Out
Q
DFN1E1
CLK
PRE
Data
D
Q
Out
En
DFN1C1
CLK
CLK
CLR
Figure 2-23 • Sample of Sequential Cells
2- 60
Data
R ev i sio n 1 7
D
Q
DFI1E1P1
Out
IGLOO nano Low Power Flash FPGAs
tCKMPWH tCKMPWL
CLK
50%
50%
tSUD
50%
Data
EN
PRE
50%
tRECPRE
tREMPRE
50%
50%
50%
CLR
tPRE2Q
50%
tREMCLR
tRECCLR
tWCLR
Out
50%
50%
0
tWPRE
tSUE
50%
50%
tHD
50%
tHE
50%
50%
50%
50%
tCLR2Q
50%
50%
tCLKQ
Figure 2-24 • Timing Model and Waveforms
Timing Characteristics
1.5 V DC Core Voltage
Table 2-86 • Register Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V
Parameter
Description
Std.
Units
tCLKQ
Clock-to-Q of the Core Register
0.89
ns
tSUD
Data Setup Time for the Core Register
0.81
ns
tHD
Data Hold Time for the Core Register
0.00
ns
tSUE
Enable Setup Time for the Core Register
0.73
ns
tHE
Enable Hold Time for the Core Register
0.00
ns
tCLR2Q
Asynchronous Clear-to-Q of the Core Register
0.60
ns
tPRE2Q
Asynchronous Preset-to-Q of the Core Register
0.62
ns
tREMCLR
Asynchronous Clear Removal Time for the Core Register
0.00
ns
tRECCLR
Asynchronous Clear Recovery Time for the Core Register
0.24
ns
tREMPRE
Asynchronous Preset Removal Time for the Core Register
0.00
ns
tRECPRE
Asynchronous Preset Recovery Time for the Core Register
0.23
ns
tWCLR
Asynchronous Clear Minimum Pulse Width for the Core Register
0.30
ns
tWPRE
Asynchronous Preset Minimum Pulse Width for the Core Register
0.30
ns
tCKMPWH
Clock Minimum Pulse Width HIGH for the Core Register
0.56
ns
tCKMPWL
Clock Minimum Pulse Width LOW for the Core Register
0.56
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 61
IGLOO nano DC and Switching Characteristics
1.2 V DC Core Voltage
Table 2-87 • Register Delays
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V
Parameter
Description
Std.
Units
tCLKQ
Clock-to-Q of the Core Register
1.61
ns
tSUD
Data Setup Time for the Core Register
1.17
ns
tHD
Data Hold Time for the Core Register
0.00
ns
tSUE
Enable Setup Time for the Core Register
1.29
ns
tHE
Enable Hold Time for the Core Register
0.00
ns
tCLR2Q
Asynchronous Clear-to-Q of the Core Register
0.87
ns
tPRE2Q
Asynchronous Preset-to-Q of the Core Register
0.89
ns
tREMCLR
Asynchronous Clear Removal Time for the Core Register
0.00
ns
tRECCLR
Asynchronous Clear Recovery Time for the Core Register
0.24
ns
tREMPRE
Asynchronous Preset Removal Time for the Core Register
0.00
ns
tRECPRE
Asynchronous Preset Recovery Time for the Core Register
0.24
ns
tWCLR
Asynchronous Clear Minimum Pulse Width for the Core Register
0.46
ns
tWPRE
Asynchronous Preset Minimum Pulse Width for the Core Register
0.46
ns
tCKMPWH
Clock Minimum Pulse Width HIGH for the Core Register
0.95
ns
tCKMPWL
Clock Minimum Pulse Width LOW for the Core Register
0.95
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
2- 62
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Global Resource Characteristics
AGLN125 Clock Tree Topology
Clock delays are device-specific. Figure 2-25 is an example of a global tree used for clock routing. The
global tree presented in Figure 2-25 is driven by a CCC located on the west side of the AGLN125 device.
It is used to drive all D-flip-flops in the device.
Central
Global Rib
VersaTile
Rows
CCC
Global Spine
Figure 2-25 • Example of Global Tree Use in an AGLN125 Device for Clock Routing
R ev i si o n 1 7
2- 63
IGLOO nano DC and Switching Characteristics
Global Tree Timing Characteristics
Global clock delays include the central rib delay, the spine delay, and the row delay. Delays do not
include I/O input buffer clock delays, as these are I/O standard–dependent, and the clock may be driven
and conditioned internally by the CCC module. For more details on clock conditioning capabilities, refer
to the "Clock Conditioning Circuits" section on page 2-70. Table 2-88 to Table 2-96 on page 2-68 present
minimum and maximum global clock delays within each device. Minimum and maximum delays are
measured with minimum and maximum loading.
Timing Characteristics
1.5 V DC Core Voltage
Table 2-88 • AGLN010 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.425 V
Std.
Parameter
Description
Min.
1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
1.13
1.42
ns
tRCKH
Input High Delay for Global Clock
1.15
1.50
ns
tRCKMPWH
Minimum Pulse Width HIGH for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width LOW for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.35
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-89 • AGLN015 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.425 V
Std.
Parameter
Description
Min.1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
1.21
1.55
ns
tRCKH
Input HIgh Delay for Global Clock
1.23
1.65
ns
tRCKMPWH
Minimum Pulse Width HIGH for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width LOW for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.42
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
2- 64
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Table 2-90 • AGLN020 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.425 V
Std.
Parameter
Description
Min.
1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
1.21
1.55
ns
tRCKH
Input High Delay for Global Clock
1.23
1.65
ns
tRCKMPWH
Minimum Pulse Width High for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width Low for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.42
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-91 • AGLN060 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.425 V
Std.
Parameter
Description
Min.1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
1.32
1.62
ns
tRCKH
Input High Delay for Global Clock
1.34
1.71
ns
tRCKMPWH
Minimum Pulse Width HIGH for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width LOW for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.38
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 65
IGLOO nano DC and Switching Characteristics
Table 2-92 • AGLN125 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.425 V
Std.
Parameter
Description
Min.
1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
1.36
1.71
ns
tRCKH
Input High Delay for Global Clock
1.39
1.82
ns
tRCKMPWH
Minimum Pulse Width High for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width Low for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.43
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
Table 2-93 • AGLN250 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.425 V
Std.
Parameter
Description
Min.1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
1.39
1.73
ns
tRCKH
Input High Delay for Global Clock
1.41
1.84
ns
tRCKMPWH
Minimum Pulse Width High for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width Low for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.43
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
2- 66
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
1.2 V DC Core Voltage
Table 2-94 • AGLN010 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.14 V
Std.
Parameter
Description
Min.1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
1.71
2.09
ns
tRCKH
Input High Delay for Global Clock
1.78
2.31
ns
tRCKMPWH
Minimum Pulse Width High for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width Low for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.53
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
Table 2-95 • AGLN015 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.14 V
Std.
Parameter
Description
Min.1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
1.81
2.26
ns
tRCKH
Input High Delay for Global Clock
1.90
2.51
ns
tRCKMPWH
Minimum Pulse Width High for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width Low for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.61
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
R ev i si o n 1 7
2- 67
IGLOO nano DC and Switching Characteristics
Table 2-96 • AGLN020 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.14 V
Std.
Parameter
Description
Min.
1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
1.81
2.26
ns
tRCKH
Input High Delay for Global Clock
1.90
2.51
ns
tRCKMPWH
Minimum Pulse Width High for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width Low for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.61
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
Table 2-97 • AGLN060 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.14 V
Std.
Parameter
Description
Min.1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
2.02
2.42
ns
tRCKH
Input High Delay for Global Clock
2.09
2.65
ns
tRCKMPWH
Minimum Pulse Width High for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width Low for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.56
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
2- 68
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Table 2-98 • AGLN125 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.14 V
Std.
Parameter
Description
Min.
1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
2.08
2.54
ns
tRCKH
Input High Delay for Global Clock
2.15
2.77
ns
tRCKMPWH
Minimum Pulse Width HIGH for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width LOW for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.62
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
Table 2-99 • AGLN250 Global Resource
Commercial-Case Conditions: TJ = 70°C, VCC = 1.14 V
Std.
Parameter
Description
Min.1
Max.2
Units
tRCKL
Input Low Delay for Global Clock
2.11
2.57
ns
tRCKH
Input High Delay for Global Clock
2.19
2.81
ns
tRCKMPWH
Minimum Pulse Width High for Global Clock
1.40
ns
tRCKMPWL
Minimum Pulse Width Low for Global Clock
1.65
ns
tRCKSW
Maximum Skew for Global Clock
0.62
ns
Notes:
1. Value reflects minimum load. The delay is measured from the CCC output to the clock pin of a sequential element,
located in a lightly loaded row (single element is connected to the global net).
2. Value reflects maximum load. The delay is measured on the clock pin of the farthest sequential element, located in a fully
loaded row (all available flip-flops are connected to the global net in the row).
3. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
R ev i si o n 1 7
2- 69
IGLOO nano DC and Switching Characteristics
Clock Conditioning Circuits
CCC Electrical Specifications
Timing Characteristics
Table 2-100 • IGLOO nano CCC/PLL Specification
For IGLOO nano V2 OR V5 Devices, 1.5 V DC Core Supply Voltage
Parameter
Min.
Clock Conditioning Circuitry Input Frequency fIN_CCC
1.5
Clock Conditioning Circuitry Output Frequency fOUT_CCC
Delay Increments in Programmable Delay Blocks
Typ.
0.75
1, 2
360
Units
250
MHz
250
MHz
3
Number of Programmable Values in Each Programmable Delay Block
Serial Clock (SCLK) for Dynamic
Max.
ps
32
PLL 4,9
100
MHz
1
ns
LockControl = 0
300
µs
LockControl = 1
6.0
ms
LockControl = 0
2.5
ns
LockControl = 1
1.5
ns
48.5
51.5
%
1.25
15.65
ns
0.025
15.65
ns
Input Cycle-to-Cycle Jitter (peak magnitude)
Acquisition Time
Tracking
Jitter 5
Output Duty Cycle
Delay Range in Block: Programmable Delay
1 1, 2
Delay Range in Block: Programmable Delay 2
Delay Range in Block: Fixed Delay
1, 2,
1, 2
VCO Output Peak-to-Peak Period Jitter
3.5
FCCC_OUT6
Max Peak-to-Peak Jitter
ns
Data 6,7,8
SSO  2
SSO  4
SSO  8
SSO  16
0.75 MHz to 50 MHz
0.50
0.60
0.80
1.20
%
50 MHz to 250 MHz
2.50
4.00
6.00
12.00
%
Notes:
1. This delay is a function of voltage and temperature. See Table 2-6 on page 2-6 and Table 2-7 on page 2-7 for deratings.
2. TJ = 25°C, VCC = 1.5 V
3. When the CCC/PLL core is generated by Microsemi core generator software, not all delay values of the specified delay
increments are available. Refer to the Libero SoC Online Help associated with the core for more information.
4. Maximum value obtained for a STD speed grade device in Worst-Case Commercial conditions. For specific junction
temperature and voltage supply levels, refer to Table 2-6 on page 2-6 and Table 2-7 on page 2-7 for derating values.
5. Tracking jitter is defined as the variation in clock edge position of PLL outputs with reference to PLL input clock edge.
Tracking jitter does not measure the variation in PLL output period, which is covered by the period jitter parameter.
6. VCO output jitter is calculated as a percentage of the VCO frequency. The jitter (in ps) can be calculated by multiplying
the VCO period by the % jitter. The VCO jitter (in ps) applies to CCC_OUT, regardless of the output divider settings. For
example, if the jitter on VCO is 300 ps, the jitter on CCC_OUT is also 300 ps, no matter what the settings are for the
output divider.
7. Measurements done with LVTTL 3.3 V 8 mA I/O drive strength and high slew rate. VCC/VCCPLL = 1.425 V,
VCCI = 3.3 V, VQ/PQ/TQ type of packages, 20 pF load.
8. SSOs are outputs that are synchronous to a single clock domain and have their clock-to-out times within ±200 ps of
each other. Switching I/Os are placed outside of the PLL bank. Refer to the "Simultaneously Switching Outputs (SSOs) and
Printed Circuit Board Layout" section in the IGLOO nano FPGA Fabric User’s Guide.
9. The AGLN010, AGLN015, and AGLN020 devices do not support PLLs.
2- 70
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Table 2-101 • IGLOO nano CCC/PLL Specification
For IGLOO nano V2 Devices, 1.2 V DC Core Supply Voltage
Parameter
Min.
Clock Conditioning Circuitry Input Frequency fIN_CCC
Clock Conditioning Circuitry Output Frequency fOUT_CCC
Max.
Units
1.5
160
MHz
0.75
160
MHz
Delay Increments in Programmable Delay Blocks 1, 2
Typ.
5803
Number of Programmable Values in Each Programmable Delay Block
Serial Clock (SCLK) for Dynamic PLL
ps
32
4,9
60
Input Cycle-to-Cycle Jitter (peak magnitude)
0.25
ns
LockControl = 0
300
µs
LockControl = 1
6.0
ms
LockControl = 0
4
ns
LockControl = 1
3
ns
48.5
51.5
%
2.3
20.86
ns
0.025
20.86
ns
Acquisition Time
Tracking Jitter
5
Output Duty Cycle
Delay Range in Block: Programmable Delay 1
1, 2
Delay Range in Block: Programmable Delay 2 1, 2
Delay Range in Block: Fixed Delay
1, 2
VCO Output Peak-to-Peak Period Jitter FCCC_OUT
5.7
6
ns
Max Peak-to-Peak Period
Jitter 6,7,8
SSO  2
SSO  4
SSO  8 SSO  16
0.75 MHz to 50MHz
0.50
1.20
2.00
3.00
%
50 MHz to 100 MHz
2.50
5.00
7.00
15.00
%
Notes:
1. This delay is a function of voltage and temperature. See Table 2-6 on page 2-6 and Table 2-7 on page 2-7 for deratings.
2. TJ = 25°C, VCC = 1.2 V.
3. When the CCC/PLL core is generated by Microsemi core generator software, not all delay values of the specified delay
increments are available. Refer to the Libero SoC Online Help associated with the core for more information.
4. Maximum value obtained for a STD speed grade device in Worst-Case Commercial conditions. For specific junction
temperature and voltage supply levels, refer to Table 2-6 on page 2-6 and Table 2-7 on page 2-7 for derating values.
5. Tracking jitter is defined as the variation in clock edge position of PLL outputs with reference to the PLL input clock
edge. Tracking jitter does not measure the variation in PLL output period, which is covered by the period jitter
parameter.
6. VCO output jitter is calculated as a percentage of the VCO frequency. The jitter (in ps) can be calculated by multiplying
the VCO period by the % jitter. The VCO jitter (in ps) applies to CCC_OUT, regardless of the output divider settings. For
example, if the jitter on VCO is 300 ps, the jitter on CCC_OUT is also 300 ps, no matter what the settings are for the
output divider.
7. Measurements done with LVTTL 3.3 V 8 mA I/O drive strength and high slew rate. VCC/VCCPLL = 1.14 V,
VCCI = 3.3 V, VQ/PQ/TQ type of packages, 20 pF load.
8. SSOs are outputs that are synchronous to a single clock domain and have their clock-to-out times within ±200 ps of
each other. Switching I/Os are placed outside of the PLL bank. Refer to the "Simultaneously Switching Outputs (SSOs) and
Printed Circuit Board Layout" section in the IGLOO nano FPGA Fabric User’s Guide.
9. The AGLN010, AGLN015, and AGLN020 devices do not support PLLs.
R ev i si o n 1 7
2- 71
IGLOO nano DC and Switching Characteristics
Output Signal
Tperiod_max
Tperiod_min
Note: Peak-to-peak jitter measurements are defined by Tpeak-to-peak = Tperiod_max – Tperiod_min.
Figure 2-26 • Peak-to-Peak Jitter Definition
2- 72
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Embedded SRAM and FIFO Characteristics
SRAM
RAM512X18
RAM4K9
ADDRA11
ADDRA10
DOUTA8
DOUTA7
RADDR8
RADDR7
RD17
RD16
ADDRA0
DINA8
DINA7
DOUTA0
RADDR0
RD0
RW1
RW0
DINA0
WIDTHA1
WIDTHA0
PIPEA
WMODEA
BLKA
WENA
CLKA
PIPE
REN
RCLK
ADDRB11
ADDRB10
DOUTB8
DOUTB7
ADDRB0
DOUTB0
DINB8
DINB7
WADDR8
WADDR7
WADDR0
WD17
WD16
WD0
DINB0
WW1
WW0
WIDTHB1
WIDTHB0
PIPEB
WMODEB
BLKB
WENB
CLKB
WEN
WCLK
RESET
RESET
Figure 2-27 • RAM Models
R ev i si o n 1 7
2- 73
IGLOO nano DC and Switching Characteristics
Timing Waveforms
tCYC
tCKH
tCKL
CLK
tAS
tAH
A0
[R|W]ADDR
A1
A2
tBKS
tBKH
BLK
tENS
tENH
WEN
tCKQ1
DOUT|RD
Dn
D0
D1
D2
tDOH1
Figure 2-28 • RAM Read for Pass-Through Output. Applicable to Both RAM4K9 and RAM512x18.
tCYC
tCKH
tCKL
CLK
t
AS
tAH
A1
A0
[R|W]ADDR
A2
tBKS
tBKH
BLK
tENH
tENS
WEN
tCKQ2
DOUT|RD
Dn
D0
D1
tDOH2
Figure 2-29 • RAM Read for Pipelined Output. Applicable to Both RAM4K9 and RAM512x18.
2- 74
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
tCYC
tCKH
tCKL
CLK
tAS
tAH
A0
[R|W]ADDR
A1
A2
tBKS
tBKH
BLK
tENS
tENH
WEN
tDS
DI0
DIN|WD
tDH
DI1
D2
Dn
DOUT|RD
Figure 2-30 • RAM Write, Output Retained (WMODE = 0). Applicable to Both RAM4K9 and RAM512x18.
tCYC
tCKH
tCKL
CLK
tAS
tAH
A0
ADDR
A1
A2
tBKS
tBKH
BLK
tENS
WEN
tDS
DI0
DIN
DOUT
(pass-through)
DOUT
(pipelined)
tDH
DI1
Dn
DI2
DI0
DI1
DI0
Dn
DI1
Figure 2-31 • RAM Write, Output as Write Data (WMODE = 1). Applicable to RAM4K9 Only.
R ev i si o n 1 7
2- 75
IGLOO nano DC and Switching Characteristics
tCYC
tCKH
tCKL
CLK
RESET
tRSTBQ
DOUT|RD
Dm
Dn
Figure 2-32 • RAM Reset. Applicable to Both RAM4K9 and RAM512x18.
2- 76
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Timing Characteristics
1.5 V DC Core Voltage
Table 2-102 • RAM4K9
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V
Parameter
Description
Std. Units
tAS
Address setup time
0.69
ns
tAH
Address hold time
0.13
ns
tENS
REN, WEN setup time
0.68
ns
tENH
REN, WEN hold time
0.13
ns
tBKS
BLK setup time
1.37
ns
tBKH
BLK hold time
0.13
ns
tDS
Input data (DIN) setup time
0.59
ns
tDH
Input data (DIN) hold time
0.30
ns
tCKQ1
Clock HIGH to new data valid on DOUT (output retained, WMODE = 0)
2.94
ns
Clock HIGH to new data valid on DOUT (flow-through, WMODE = 1)
2.55
ns
tCKQ2
Clock HIGH to new data valid on DOUT (pipelined)
1.51
ns
tC2CWWL1
Address collision clk-to-clk delay for reliable write after write on same address; applicable 0.23
to closing edge
ns
tC2CRWH1
Address collision clk-to-clk delay for reliable read access after write on same address; 0.35
applicable to opening edge
ns
tC2CWRH1
Address collision clk-to-clk delay for reliable write access after read on same address; 0.41
applicable to opening edge
ns
tRSTBQ
RESET Low to data out Low on DOUT (flow-through)
1.72
ns
RESET Low to data out Low on DOUT (pipelined)
1.72
ns
tREMRSTB
RESET removal
0.51
ns
tRECRSTB
RESET recovery
2.68
ns
tMPWRSTB
RESET minimum pulse width
0.68
ns
tCYC
Clock cycle time
6.24
ns
FMAX
Maximum frequency
160
MHz
Notes:
1. For more information, refer to the application note Simultaneous Read-Write Operations in Dual-Port SRAM for FlashBased cSoCs and FPGAs.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 77
IGLOO nano DC and Switching Characteristics
Table 2-103 • RAM512X18
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V
Parameter
Description
Std. Units
tAS
Address setup time
0.69
ns
tAH
Address hold time
0.13
ns
tENS
REN, WEN setup time
0.61
ns
tENH
REN, WEN hold time
0.07
ns
tDS
Input data (WD) setup time
0.59
ns
tDH
Input data (WD) hold time
0.30
ns
tCKQ1
Clock HIGH to new data valid on RD (output retained)
3.51
ns
tCKQ2
Clock HIGH to new data valid on RD (pipelined)
1.43
ns
tC2CRWH1
Address collision clk-to-clk delay for reliable read access after write on same address; 0.35
applicable to opening edge
ns
tC2CWRH1
Address collision clk-to-clk delay for reliable write access after read on same address; 0.42
applicable to opening edge
ns
tRSTBQ
RESET Low to data out Low on RD (flow-through)
1.72
ns
RESET Low to data out Low on RD (pipelined)
1.72
ns
tREMRSTB
RESET removal
0.51 0.51
tRECRSTB
RESET recovery
2.68
ns
tMPWRSTB
RESET minimum pulse width
0.68
ns
tCYC
Clock cycle time
6.24
ns
FMAX
Maximum frequency
160
MHz
Notes:
1. For more information, refer to the application note Simultaneous Read-Write Operations in Dual-Port SRAM for FlashBased cSoCs and FPGAs.
2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
2- 78
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
1.2 V DC Core Voltage
Table 2-104 • RAM4K9
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V
Parameter
Description
Std.
Units
tAS
Address setup time
1.28
ns
tAH
Address hold time
0.25
ns
tENS
REN, WEN setup time
1.25
ns
tENH
REN, WEN hold time
0.25
ns
tBKS
BLK setup time
2.54
ns
tBKH
BLK hold time
0.25
ns
tDS
Input data (DIN) setup time
1.10
ns
tDH
Input data (DIN) hold time
0.55
ns
tCKQ1
Clock HIGH to new data valid on DOUT (output retained, WMODE = 0)
5.51
ns
Clock HIGH to new data valid on DOUT (flow-through, WMODE = 1)
4.77
ns
tCKQ2
Clock HIGH to new data valid on DOUT (pipelined)
2.82
ns
tC2CWWL1
Address collision clk-to-clk delay for reliable write after write on same address;
applicable to closing edge
0.30
ns
tC2CRWH1
Address collision clk-to-clk delay for reliable read access after write on same address;
applicable to opening edge
0.89
ns
tC2CWRH1
Address collision clk-to-clk delay for reliable write access after read on same address;
applicable to opening edge
1.01
ns
tRSTBQ
RESET LOW to data out LOW on DOUT (flow-through)
3.21
ns
RESET LOW to data out LOW on DO (pipelined)
3.21
ns
tREMRSTB
RESET removal
0.93
ns
tRECRSTB
RESET recovery
4.94
ns
tMPWRSTB
RESET minimum pulse width
1.18
ns
tCYC
Clock cycle time
10.90
ns
FMAX
Maximum frequency
92
MHz
Notes:
1. For more information, refer to the application note Simultaneous Read-Write Operations in Dual-Port SRAM for FlashBased cSoCs and FPGAs.
2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
R ev i si o n 1 7
2- 79
IGLOO nano DC and Switching Characteristics
Table 2-105 • RAM512X18
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V
Parameter
Std.
Units
tAS
Address setup time
Description
1.28
ns
tAH
Address hold time
0.25
ns
tENS
REN, WEN setup time
1.13
ns
tENH
REN, WEN hold time
0.13
ns
tDS
Input data (WD) setup time
1.10
ns
tDH
Input data (WD) hold time
0.55
ns
tCKQ1
Clock High to new data valid on RD (output retained)
6.56
ns
tCKQ2
Clock High to new data valid on RD (pipelined)
2.67
ns
tC2CRWH1
Address collision clk-to-clk delay for reliable read access after write on same address;
applicable to opening edge
0.87
ns
tC2CWRH1
Address collision clk-to-clk delay for reliable write access after read on same address;
applicable to opening edge
1.04
ns
tRSTBQ
RESET LOW to data out LOW on RD (flow through)
3.21
ns
RESET LOW to data out LOW on RD (pipelined)
3.21
ns
tREMRSTB
RESET removal
0.93
ns
tRECRSTB
RESET recovery
4.94
ns
tMPWRSTB
RESET minimum pulse width
1.18
ns
tCYC
Clock cycle time
10.90
ns
FMAX
Maximum frequency
92
MHz
Notes:
1. For more information, refer to the application note Simultaneous Read-Write Operations in Dual-Port SRAM for FlashBased cSoCs and FPGAs.
2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
2- 80
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
FIFO
FIFO4K18
RW2
RW1
RW0
WW2
WW1
WW0
ESTOP
FSTOP
RD17
RD16
RD0
FULL
AFULL
EMPTY
AEMPTY
AEVAL11
AEVAL10
AEVAL0
AFVAL11
AFVAL10
AFVAL0
REN
RBLK
RCLK
WD17
WD16
WD0
WEN
WBLK
WCLK
RPIPE
RESET
Figure 2-33 • FIFO Model
R ev i si o n 1 7
2- 81
IGLOO nano DC and Switching Characteristics
Timing Waveforms
tCYC
RCLK
tENH
tENS
REN
tBKH
tBKS
RBLK
tCKQ1
RD
(flow-through)
Dn
D0
D1
D2
D0
D1
tCKQ2
RD
(pipelined)
Dn
Figure 2-34 • FIFO Read
tCYC
WCLK
tENS
tENH
WEN
WBLK
tBKS
tBKH
tDS
WD
DI0
tDH
DI1
Figure 2-35 • FIFO Write
2- 82
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
RCLK/
WCLK
tMPWRSTB
tRSTCK
RESET
tRSTFG
EMPTY
tRSTAF
AEMPTY
tRSTFG
FULL
tRSTAF
AFULL
WA/RA
(Address Counter)
MATCH (A0)
Figure 2-36 • FIFO Reset
tCYC
RCLK
tRCKEF
EMPTY
tCKAF
AEMPTY
WA/RA
(Address Counter)
NO MATCH
NO MATCH
Dist = AEF_TH
MATCH (EMPTY)
Figure 2-37 • FIFO EMPTY Flag and AEMPTY Flag Assertion
R ev i si o n 1 7
2- 83
IGLOO nano DC and Switching Characteristics
tCYC
WCLK
tWCKFF
FULL
tCKAF
AFULL
WA/RA NO MATCH
(Address Counter)
NO MATCH
Dist = AFF_TH
MATCH (FULL)
Figure 2-38 • FIFO FULL Flag and AFULL Flag Assertion
WCLK
WA/RA MATCH
(Address Counter) (EMPTY)
RCLK
NO MATCH
1st Rising
Edge
After 1st
Write
NO MATCH
NO MATCH
NO MATCH
Dist = AEF_TH + 1
2nd Rising
Edge
After 1st
Write
tRCKEF
EMPTY
tCKAF
AEMPTY
Figure 2-39 • FIFO EMPTY Flag and AEMPTY Flag Deassertion
RCLK
WA/RA
(Address Counter)
WCLK
MATCH (FULL)
NO MATCH
1st Rising
Edge
After 1st
Read
NO MATCH
NO MATCH
NO MATCH
Dist = AFF_TH – 1
1st Rising
Edge
After 2nd
Read
tWCKF
FULL
tCKAF
AFULL
Figure 2-40 • FIFO FULL Flag and AFULL Flag Deassertion
2- 84
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Timing Characteristics
1.5 V DC Core Voltage
Table 2-106 • FIFO
Worst Commercial-Case Conditions: TJ = 70°C, VCC = 1.425 V
Parameter
Description
Std.
Units
tENS
REN, WEN Setup Time
1.66
ns
tENH
REN, WEN Hold Time
0.13
ns
tBKS
BLK Setup Time
0.30
ns
tBKH
BLK Hold Time
0.00
ns
tDS
Input Data (WD) Setup Time
0.63
ns
tDH
Input Data (WD) Hold Time
0.20
ns
tCKQ1
Clock High to New Data Valid on RD (flow-through)
2.77
ns
tCKQ2
Clock High to New Data Valid on RD (pipelined)
1.50
ns
tRCKEF
RCLK High to Empty Flag Valid
2.94
ns
tWCKFF
WCLK High to Full Flag Valid
2.79
ns
tCKAF
Clock High to Almost Empty/Full Flag Valid
10.71
ns
tRSTFG
RESET Low to Empty/Full Flag Valid
2.90
ns
tRSTAF
RESET Low to Almost Empty/Full Flag Valid
10.60
ns
tRSTBQ
RESET Low to Data Out LOW on RD (flow-through)
1.68
ns
RESET Low to Data Out LOW on RD (pipelined)
1.68
ns
tREMRSTB
RESET Removal
0.51
ns
tRECRSTB
RESET Recovery
2.68
ns
tMPWRSTB
RESET Minimum Pulse Width
0.68
ns
tCYC
Clock Cycle Time
6.24
ns
FMAX
Maximum Frequency for FIFO
160
MHz
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
R ev i si o n 1 7
2- 85
IGLOO nano DC and Switching Characteristics
1.2 V DC Core Voltage
Table 2-107 • FIFO
Worst Commercial-Case Conditions: TJ = 70°C, VCC = 1.14 V
Parameter
Description
Std.
Units
tENS
REN, WEN Setup Time
3.44
ns
tENH
REN, WEN Hold Time
0.26
ns
tBKS
BLK Setup Time
0.30
ns
tBKH
BLK Hold Time
0.00
ns
tDS
Input Data (DI) Setup Time
1.30
ns
tDH
Input Data (DI) Hold Time
0.41
ns
tCKQ1
Clock High to New Data Valid on RD (flow-through)
5.67
ns
tCKQ2
Clock High to New Data Valid on RD (pipelined)
3.02
ns
tRCKEF
RCLK High to Empty Flag Valid
6.02
ns
tWCKFF
WCLK High to Full Flag Valid
5.71
ns
tCKAF
Clock High to Almost Empty/Full Flag Valid
22.17
ns
tRSTFG
RESET LOW to Empty/Full Flag Valid
5.93
ns
tRSTAF
RESET LOW to Almost Empty/Full Flag Valid
21.94
ns
tRSTBQ
RESET LOW to Data Out Low on RD (flow-through)
3.41
ns
RESET LOW to Data Out Low on RD (pipelined)
4.09
3.41
tREMRSTB
RESET Removal
1.02
ns
tRECRSTB
RESET Recovery
5.48
ns
tMPWRSTB
RESET Minimum Pulse Width
1.18
ns
tCYC
Clock Cycle Time
10.90
ns
FMAX
Maximum Frequency for FIFO
92
MHz
Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values.
2- 86
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
Embedded FlashROM Characteristics
tSU
CLK
tSU
tHOLD
Address
tSU
tHOLD
A0
tHOLD
A1
tCKQ2
tCKQ2
D0
Data
tCKQ2
D0
D1
Figure 2-41 • Timing Diagram
Timing Characteristics
1.5 V DC Core Voltage
Table 2-108 • Embedded FlashROM Access Time
Worst Commercial-Case Conditions: TJ = 70°C, VCC = 1.425 V
Parameter
Description
Std.
Units
tSU
Address Setup Time
0.57
ns
tHOLD
Address Hold Time
0.00
ns
tCK2Q
Clock to Out
20.90
ns
FMAX
Maximum Clock Frequency
15
MHz
Std.
Units
1.2 V DC Core Voltage
Table 2-109 • Embedded FlashROM Access Time
Worst Commercial-Case Conditions: TJ = 70°C, VCC = 1.14 V
Parameter
Description
tSU
Address Setup Time
0.59
ns
tHOLD
Address Hold Time
0.00
ns
tCK2Q
Clock to Out
35.74
ns
FMAX
Maximum Clock Frequency
10
MHz
R ev i si o n 1 7
2- 87
JTAG 1532 Characteristics
JTAG timing delays do not include JTAG I/Os. To obtain complete JTAG timing, add I/O buffer delays to
the corresponding standard selected; refer to the I/O timing characteristics in the "User I/O
Characteristics" section on page 2-15 for more details.
Timing Characteristics
1.5 V DC Core Voltage
Table 2-110 • JTAG 1532
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.425 V
Parameter
Description
Std.
Units
tDISU
Test Data Input Setup Time
1.00
ns
tDIHD
Test Data Input Hold Time
2.00
ns
tTMSSU
Test Mode Select Setup Time
1.00
ns
tTMDHD
Test Mode Select Hold Time
2.00
ns
tTCK2Q
Clock to Q (data out)
8.00
ns
tRSTB2Q
Reset to Q (data out)
25.00
ns
FTCKMAX
TCK Maximum Frequency
15
MHz
tTRSTREM
ResetB Removal Time
0.58
ns
tTRSTREC
ResetB Recovery Time
0.00
ns
tTRSTMPW
ResetB Minimum Pulse
TBD
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
1.2 V DC Core Voltage
Table 2-111 • JTAG 1532
Commercial-Case Conditions: TJ = 70°C, Worst-Case VCC = 1.14 V
Parameter
Description
Std.
Units
tDISU
Test Data Input Setup Time
1.50
ns
tDIHD
Test Data Input Hold Time
3.00
ns
tTMSSU
Test Mode Select Setup Time
1.50
ns
tTMDHD
Test Mode Select Hold Time
3.00
ns
tTCK2Q
Clock to Q (data out)
11.00
ns
tRSTB2Q
Reset to Q (data out)
30.00
ns
FTCKMAX
TCK Maximum Frequency
9.00
MHz
tTRSTREM
ResetB Removal Time
1.18
ns
tTRSTREC
ResetB Recovery Time
0.00
ns
tTRSTMPW
ResetB Minimum Pulse
TBD
ns
Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-6 for derating values.
3 – Pin Descriptions
Supply Pins
GND
Ground
Ground supply voltage to the core, I/O outputs, and I/O logic.
GNDQ
Ground (quiet)
Quiet ground supply voltage to input buffers of I/O banks. Within the package, the GNDQ plane is
decoupled from the simultaneous switching noise originated from the output buffer ground domain. This
minimizes the noise transfer within the package and improves input signal integrity. GNDQ must always
be connected to GND on the board.
VCC
Core Supply Voltage
Supply voltage to the FPGA core, nominally 1.5 V for IGLOO nano V5 devices, and 1.2 V or 1.5 V for
IGLOO nano V2 devices. VCC is required for powering the JTAG state machine in addition to VJTAG.
Even when a device is in bypass mode in a JTAG chain of interconnected devices, both VCC and VJTAG
must remain powered to allow JTAG signals to pass through the device.
VCCIBx
I/O Supply Voltage
Supply voltage to the bank's I/O output buffers and I/O logic. Bx is the I/O bank number. There are up to
eight I/O banks on low power flash devices plus a dedicated VJTAG bank. Each bank can have a
separate VCCI connection. All I/Os in a bank will run off the same VCCIBx supply. VCCI can be 1.2 V,
1.5 V, 1.8 V, 2.5 V, or 3.3 V, nominal voltage. Unused I/O banks should have their corresponding VCCI
pins tied to GND.
VMVx
I/O Supply Voltage (quiet)
Quiet supply voltage to the input buffers of each I/O bank. x is the bank number. Within the package, the
VMV plane biases the input stage of the I/Os in the I/O banks. This minimizes the noise transfer within
the package and improves input signal integrity. Each bank must have at least one VMV connection, and
no VMV should be left unconnected. All I/Os in a bank run off the same VMVx supply. VMV is used to
provide a quiet supply voltage to the input buffers of each I/O bank. VMVx can be 1.2 V, 1.5 V, 1.8 V,
2.5 V, or 3.3 V, nominal voltage. Unused I/O banks should have their corresponding VMV pins tied to GND.
VMV and VCCI should be at the same voltage within a given I/O bank. Used VMV pins must be
connected to the corresponding VCCI pins of the same bank (i.e., VMV0 to VCCIB0, VMV1 to VCCIB1,
etc.).
VCCPLA/B/C/D/E/F
PLL Supply Voltage
Supply voltage to analog PLL, nominally 1.5 V or 1.2 V.
When the PLLs are not used, the Microsemi Designer place-and-route tool automatically disables the
unused PLLs to lower power consumption. The user should tie unused VCCPLx and VCOMPLx pins to
ground. Microsemi recommends tying VCCPLx to VCC and using proper filtering circuits to decouple
VCC noise from the PLLs. Refer to the PLL Power Supply Decoupling section of the "Clock Conditioning
Circuits in IGLOO and ProASIC3 Devices" chapter in the IGLOO nano FPGA Fabric User’s Guide for a
complete board solution for the PLL analog power supply and ground.
There is one VCCPLF pin on IGLOO nano devices.
VCOMPLA/B/C/D/E/F
PLL Ground
Ground to analog PLL power supplies. When the PLLs are not used, the Microsemi Designer place-androute tool automatically disables the unused PLLs to lower power consumption. The user should tie
unused VCCPLx and VCOMPLx pins to ground.
There is one VCOMPLF pin on IGLOO nano devices.
VJTAG
JTAG Supply Voltage
Low power flash devices have a separate bank for the dedicated JTAG pins. The JTAG pins can be run
at any voltage from 1.5 V to 3.3 V (nominal). Isolating the JTAG power supply in a separate I/O bank
gives greater flexibility in supply selection and simplifies power supply and PCB design. If the JTAG
R ev i si o n 1 7
3 -1
Pin Descriptions
interface is neither used nor planned for use, the VJTAG pin together with the TRST pin could be tied to
GND. It should be noted that VCC is required to be powered for JTAG operation; VJTAG alone is
insufficient. If a device is in a JTAG chain of interconnected boards, the board containing the device can
be powered down, provided both VJTAG and VCC to the part remain powered; otherwise, JTAG signals
will not be able to transition the device, even in bypass mode.
Microsemi recommends that VPUMP and VJTAG power supplies be kept separate with independent
filtering capacitors rather than supplying them from a common rail.
VPUMP
Programming Supply Voltage
IGLOO nano devices support single-voltage ISP of the configuration flash and FlashROM. For
programming, VPUMP should be 3.3 V nominal. During normal device operation, VPUMP can be left
floating or can be tied (pulled up) to any voltage between 0 V and the VPUMP maximum. Programming
power supply voltage (VPUMP) range is listed in the datasheet.
When the VPUMP pin is tied to ground, it will shut off the charge pump circuitry, resulting in no sources of
oscillation from the charge pump circuitry.
For proper programming, 0.01 µF and 0.33 µF capacitors (both rated at 16 V) are to be connected in
parallel across VPUMP and GND, and positioned as close to the FPGA pins as possible.
Microsemi recommends that VPUMP and VJTAG power supplies be kept separate with independent
filtering capacitors rather than supplying them from a common rail.
User Pins
I/O
User Input/Output
The I/O pin functions as an input, output, tristate, or bidirectional buffer. Input and output signal levels are
compatible with the I/O standard selected.
During programming, I/Os become tristated and weakly pulled up to VCCI. With VCCI, VMV, and VCC
supplies continuously powered up, when the device transitions from programming to operating mode, the
I/Os are instantly configured to the desired user configuration.
Unused I/Os are configured as follows:
GL
•
Output buffer is disabled (with tristate value of high impedance)
•
Input buffer is disabled (with tristate value of high impedance)
•
Weak pull-up is programmed
Globals
GL I/Os have access to certain clock conditioning circuitry (and the PLL) and/or have direct access to the
global network (spines). Additionally, the global I/Os can be used as regular I/Os, since they have
identical capabilities. Unused GL pins are configured as inputs with pull-up resistors.
See more detailed descriptions of global I/O connectivity in the "Clock Conditioning Circuits in IGLOO
and ProASIC3 Devices" chapter in the IGLOO nano FPGA Fabric User’s Guide. All inputs labeled
GC/GF are direct inputs into the quadrant clocks. For example, if GAA0 is used for an input, GAA1 and
GAA2 are no longer available for input to the quadrant globals. All inputs labeled GC/GF are direct inputs
into the chip-level globals, and the rest are connected to the quadrant globals. The inputs to the global
network are multiplexed, and only one input can be used as a global input.
Refer to the "I/O Structures in nano Devices" chapter of the IGLOO nano FPGA Fabric User’s Guide for
an explanation of the naming of global pins.
FF
Flash*Freeze Mode Activation Pin
Flash*Freeze is available on IGLOO nano devices. The FF pin is a dedicated input pin used to enter and
exit Flash*Freeze mode. The FF pin is active low, has the same characteristics as a single-ended I/O,
and must meet the maximum rise and fall times. When Flash*Freeze mode is not used in the design, the
FF pin is available as a regular I/O.
When Flash*Freeze mode is used, the FF pin must not be left floating to avoid accidentally entering
Flash*Freeze mode. While in Flash*Freeze mode, the Flash*Freeze pin should be constantly asserted.
The Flash*Freeze pin can be used with any single-ended I/O standard supported by the I/O bank in
which the pin is located, and input signal levels compatible with the I/O standard selected. The FF pin
3- 2
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
should be treated as a sensitive asynchronous signal. When defining pin placement and board layout,
simultaneously switching outputs (SSOs) and their effects on sensitive asynchronous pins must be
considered.
Unused FF or I/O pins are tristated with weak pull-up. This default configuration applies to both
Flash*Freeze mode and normal operation mode. No user intervention is required.
Table 3-1 shows the Flash*Freeze pin location on the available packages for IGLOO nano devices. The
Flash*Freeze pin location is independent of device (except for a PQ208 package), allowing migration to
larger or smaller IGLOO nano devices while maintaining the same pin location on the board. Refer to the
"Flash*Freeze Technology and Low Power Modes" chapter of the IGLOO nano FPGA Fabric User’s
Guide for more information on I/O states during Flash*Freeze mode.
Table 3-1 • Flash*Freeze Pin Locations for IGLOO nano Devices
Package
Flash*Freeze Pin
CS81/UC81
H2
QN48
14
QN68
18
VQ100
27
UC36
E2
JTAG Pins
Low power flash devices have a separate bank for the dedicated JTAG pins. The JTAG pins can be run
at any voltage from 1.5 V to 3.3 V (nominal). VCC must also be powered for the JTAG state machine to
operate, even if the device is in bypass mode; VJTAG alone is insufficient. Both VJTAG and VCC to the
part must be supplied to allow JTAG signals to transition the device. Isolating the JTAG power supply in a
separate I/O bank gives greater flexibility in supply selection and simplifies power supply and PCB
design. If the JTAG interface is neither used nor planned for use, the VJTAG pin together with the TRST
pin could be tied to GND.
TCK
Test Clock
Test clock input for JTAG boundary scan, ISP, and UJTAG. The TCK pin does not have an internal
pull-up/-down resistor. If JTAG is not used, Microsemi recommends tying off TCK to GND through a
resistor placed close to the FPGA pin. This prevents JTAG operation in case TMS enters an undesired
state.
Note that to operate at all VJTAG voltages, 500  to 1 k will satisfy the requirements. Refer to Table 3-2
for more information.
Table 3-2 • Recommended Tie-Off Values for the TCK and TRST Pins
Tie-Off Resistance 1,2
VJTAG
VJTAG at 3.3 V
200  to 1 k
VJTAG at 2.5 V
200  to 1 k
VJTAG at 1.8 V
500  to 1 k
VJTAG at 1.5 V
500  to 1 k
Notes:
1. The TCK pin can be pulled-up or pulled-down.
2. The TRST pin is pulled-down.
3. Equivalent parallel resistance if more than one device is on the JTAG chain
R ev i si o n 1 7
3 -3
Pin Descriptions
Table 3-3 • TRST and TCK Pull-Down Recommendations
VJTAG
Tie-Off Resistance*
VJTAG at 3.3 V
200  to 1 k
VJTAG at 2.5 V
200  to 1 k
VJTAG at 1.8 V
500  to 1 k
VJTAG at 1.5 V
500  to 1 k
Note: Equivalent parallel resistance if more than one device is on the JTAG chain
TDI
Test Data Input
Serial input for JTAG boundary scan, ISP, and UJTAG usage. There is an internal weak pull-up resistor
on the TDI pin.
TDO
Test Data Output
Serial output for JTAG boundary scan, ISP, and UJTAG usage.
TMS
Test Mode Select
The TMS pin controls the use of the IEEE 1532 boundary scan pins (TCK, TDI, TDO, TRST). There is an
internal weak pull-up resistor on the TMS pin.
TRST
Boundary Scan Reset Pin
The TRST pin functions as an active-low input to asynchronously initialize (or reset) the boundary scan
circuitry. There is an internal weak pull-up resistor on the TRST pin. If JTAG is not used, an external
pull-down resistor could be included to ensure the test access port (TAP) is held in reset mode. The
resistor values must be chosen from Table 3-2 and must satisfy the parallel resistance value
requirement. The values in Table 3-2 correspond to the resistor recommended when a single device is
used, and the equivalent parallel resistor when multiple devices are connected via a JTAG chain.
In critical applications, an upset in the JTAG circuit could allow entrance to an undesired JTAG state. In
such cases, Microsemi recommends tying off TRST to GND through a resistor placed close to the FPGA
pin.
Note that to operate at all VJTAG voltages, 500  to 1 k will satisfy the requirements.
Special Function Pins
NC
No Connect
This pin is not connected to circuitry within the device. These pins can be driven to any voltage or can be
left floating with no effect on the operation of the device.
DC
Do Not Connect
This pin should not be connected to any signals on the PCB. These pins should be left unconnected.
Packaging
Semiconductor technology is constantly shrinking in size while growing in capability and functional
integration. To enable next-generation silicon technologies, semiconductor packages have also evolved
to provide improved performance and flexibility.
Microsemi consistently delivers packages that provide the necessary mechanical and environmental
protection to ensure consistent reliability and performance. Microsemi IC packaging technology
efficiently supports high-density FPGAs with large-pin-count Ball Grid Arrays (BGAs), but is also flexible
enough to accommodate stringent form factor requirements for Chip Scale Packaging (CSP). In addition,
Microsemi offers a variety of packages designed to meet your most demanding application and economic
requirements for today's embedded and mobile systems.
3- 4
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
Related Documents
User’s Guides
IGLOO nano FPGA Fabric User’s Guide
http://www.microsemi.com/soc/documents/IGLOO_nano_UG.pdf
Packaging Documents
The following documents provide packaging information and device selection for low power flash
devices.
Product Catalog
http://www.microsemi.com/soc/documents/ProdCat_PIB.pdf
Lists devices currently recommended for new designs and the packages available for each member of
the family. Use this document or the datasheet tables to determine the best package for your design, and
which package drawing to use.
Package Mechanical Drawings
http://www.microsemi.com/soc/documents/PckgMechDrwngs.pdf
This document contains the package mechanical drawings for all packages currently or previously
supplied by Microsemi. Use the bookmarks to navigate to the package mechanical drawings.
Additional packaging materials are on the Microsemi SoC Products Group website:
http://www.microsemi.com/soc/products/solutions/package/docs.aspx.
R ev i si o n 1 7
3 -5
4 – Package Pin Assignments
UC36
Pin 1 Pad Corner
6
5
4
3
2
1
A
B
C
D
E
F
Note: This is the bottom view of the package.
Note
For Package Manufacturing and Environmental information, visit the Resource Center at
http://www.microsemi.com/soc/products/solutions/package/docs.aspx.
R ev i si o n 1 7
4 -1
Package Pin Assignments
UC36
UC36
Pin Number
AGLN010
Function
Pin Number
AGLN010
Function
A1
IO21RSB1
F5
TMS
A2
IO18RSB1
F6
TDO
A3
IO13RSB1
A4
GDC0/IO00RSB0
A5
IO06RSB0
A6
GDA0/IO04RSB0
B1
GEC0/IO37RSB1
B2
IO20RSB1
B3
IO15RSB1
B4
IO09RSB0
B5
IO08RSB0
B6
IO07RSB0
C1
IO22RSB1
C2
GEA0/IO34RSB1
C3
GND
C4
GND
C5
VCCIB0
C6
IO02RSB0
D1
IO33RSB1
D2
VCCIB1
D3
VCC
D4
VCC
D5
IO10RSB0
D6
IO11RSB0
E1
IO32RSB1
E2
FF/IO31RSB1
E3
TCK
E4
VPUMP
E5
TRST
E6
VJTAG
F1
IO29RSB1
F2
IO25RSB1
F3
IO23RSB1
F4
TDI
4- 2
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
UC81
A1 Ball Pad Corner
9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
Note: This is the bottom view of the package.
Note
For Package Manufacturing and Environmental information, visit the Resource Center at
http://www.microsemi.com/soc/products/solutions/package/docs.aspx.
R ev i si o n 1 7
4 -3
Package Pin Assignments
UC81
UC81
UC81
Pin Number
AGLN020 Function
Pin Number
AGLN020 Function
Pin Number
AGLN020 Function
A1
IO64RSB2
E1
GEC0/IO48RSB2
J1
IO38RSB1
A2
IO54RSB2
E2
GEA0/IO47RSB2
J2
IO37RSB1
A3
IO57RSB2
E3
NC
J3
IO33RSB1
A4
IO36RSB1
E4
VCCIB1
J4
IO30RSB1
A5
IO32RSB1
E5
VCC
J5
IO27RSB1
A6
IO24RSB1
E6
VCCIB0
J6
IO23RSB1
A7
IO20RSB1
E7
NC
J7
TCK
A8
IO04RSB0
E8
GDA0/IO15RSB0
J8
TMS
A9
IO08RSB0
E9
GDC0/IO14RSB0
J9
VPUMP
B1
IO59RSB2
F1
IO46RSB2
B2
IO55RSB2
F2
IO45RSB2
B3
IO62RSB2
F3
NC
B4
IO34RSB1
F4
GND
B5
IO28RSB1
F5
VCCIB1
B6
IO22RSB1
F6
NC
B7
IO18RSB1
F7
NC
B8
IO00RSB0
F8
IO16RSB0
B9
IO03RSB0
F9
IO17RSB0
C1
IO51RSB2
G1
IO43RSB2
C2
IO50RSB2
G2
IO42RSB2
C3
NC
G3
IO41RSB2
C4
NC
G4
IO31RSB1
C5
NC
G5
NC
C6
NC
G6
IO21RSB1
C7
NC
G7
NC
C8
IO10RSB0
G8
VJTAG
C9
IO07RSB0
G9
TRST
D1
IO49RSB2
H1
IO40RSB2
D2
IO44RSB2
H2
FF/IO39RSB1
D3
NC
H3
IO35RSB1
D4
VCC
H4
IO29RSB1
D5
VCCIB2
H5
IO26RSB1
D6
GND
H6
IO25RSB1
D7
NC
H7
IO19RSB1
D8
IO13RSB0
H8
TDI
D9
IO12RSB0
H9
TDO
4- 4
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
UC81
UC81
UC81
Pin Number
AGLN030Z
Function
Pin Number
AGLN030Z
Function
Pin Number
AGLN030Z
Function
A1
IO00RSB0
D9
IO30RSB0
H8
TDI
A2
IO02RSB0
E1
GEB0/IO71RSB1
H9
TDO
A3
IO06RSB0
E2
GEA0/IO72RSB1
J1
IO63RSB1
A4
IO11RSB0
E3
GEC0/IO73RSB1
J2
IO61RSB1
A5
IO16RSB0
E4
VCCIB1
J3
IO59RSB1
A6
IO19RSB0
E5
VCC
J4
IO56RSB1
A7
IO22RSB0
E6
VCCIB0
J5
IO52RSB1
A8
IO24RSB0
E7
GDC0/IO32RSB0
J6
IO44RSB1
A9
IO26RSB0
E8
GDA0/IO33RSB0
J7
TCK
B1
IO81RSB1
E9
GDB0/IO34RSB0
J8
TMS
B2
IO04RSB0
F1
IO68RSB1
J9
VPUMP
B3
IO10RSB0
F2
IO67RSB1
B4
IO13RSB0
F3
IO64RSB1
B5
IO15RSB0
F4
GND
B6
IO20RSB0
F5
VCCIB1
B7
IO21RSB0
F6
IO47RSB1
B8
IO28RSB0
F7
IO36RSB0
B9
IO25RSB0
F8
IO38RSB0
C1
IO79RSB1
F9
IO40RSB0
C2
IO80RSB1
G1
IO65RSB1
C3
IO08RSB0
G2
IO66RSB1
C4
IO12RSB0
G3
IO57RSB1
C5
IO17RSB0
G4
IO53RSB1
C6
IO14RSB0
G5
IO49RSB1
C7
IO18RSB0
G6
IO45RSB1
C8
IO29RSB0
G7
IO46RSB1
C9
IO27RSB0
G8
VJTAG
D1
IO74RSB1
G9
TRST
D2
IO76RSB1
H1
IO62RSB1
D3
IO77RSB1
H2
FF/IO60RSB1
D4
VCC
H3
IO58RSB1
D5
VCCIB0
H4
IO54RSB1
D6
GND
H5
IO48RSB1
D7
IO23RSB0
H6
IO43RSB1
D8
IO31RSB0
H7
IO42RSB1
R ev i si o n 1 7
4 -5
Package Pin Assignments
CS81
A1 Ball Pad Corner
9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
Note: This is the bottom view of the package.
Note
For Package Manufacturing and Environmental information, visit the Resource Center at
http://www.microsemi.com/soc/products/solutions/package/docs.aspx.
4- 6
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
CS81
CS81
CS81
Pin Number
AGLN020 Function
Pin Number
AGLN020 Function
Pin Number
AGLN020 Function
A1
IO64RSB2
E1
GEC0/IO48RSB2
J1
IO38RSB1
A2
IO54RSB2
E2
GEA0/IO47RSB2
J2
IO37RSB1
A3
IO57RSB2
E3
NC
J3
IO33RSB1
A4
IO36RSB1
E4
VCCIB1
J4
IO30RSB1
A5
IO32RSB1
E5
VCC
J5
IO27RSB1
A6
IO24RSB1
E6
VCCIB0
J6
IO23RSB1
A7
IO20RSB1
E7
NC
J7
TCK
A8
IO04RSB0
E8
GDA0/IO15RSB0
J8
TMS
A9
IO08RSB0
E9
GDC0/IO14RSB0
J9
VPUMP
B1
IO59RSB2
F1
IO46RSB2
B2
IO55RSB2
F2
IO45RSB2
B3
IO62RSB2
F3
NC
B4
IO34RSB1
F4
GND
B5
IO28RSB1
F5
VCCIB1
B6
IO22RSB1
F6
NC
B7
IO18RSB1
F7
NC
B8
IO00RSB0
F8
IO16RSB0
B9
IO03RSB0
F9
IO17RSB0
C1
IO51RSB2
G1
IO43RSB2
C2
IO50RSB2
G2
IO42RSB2
C3
NC
G3
IO41RSB2
C4
NC
G4
IO31RSB1
C5
NC
G5
NC
C6
NC
G6
IO21RSB1
C7
NC
G7
NC
C8
IO10RSB0
G8
VJTAG
C9
IO07RSB0
G9
TRST
D1
IO49RSB2
H1
IO40RSB2
D2
IO44RSB2
H2
FF/IO39RSB1
D3
NC
H3
IO35RSB1
D4
VCC
H4
IO29RSB1
D5
VCCIB2
H5
IO26RSB1
D6
GND
H6
IO25RSB1
D7
NC
H7
IO19RSB1
D8
IO13RSB0
H8
TDI
D9
IO12RSB0
H9
TDO
R ev i si o n 1 7
4 -7
Package Pin Assignments
CS81
CS81
CS81
Pin Number
AGLN030Z
Function
Pin Number
AGLN030Z
Function
Pin Number
AGLN030Z
Function
A1
IO00RSB0
D9
IO30RSB0
H8
TDI
A2
IO02RSB0
E1
GEB0/IO71RSB1
H9
TDO
A3
IO06RSB0
E2
GEA0/IO72RSB1
J1
IO63RSB1
A4
IO11RSB0
E3
GEC0/IO73RSB1
J2
IO61RSB1
A5
IO16RSB0
E4
VCCIB1
J3
IO59RSB1
A6
IO19RSB0
E5
VCC
J4
IO56RSB1
A7
IO22RSB0
E6
VCCIB0
J5
IO52RSB1
A8
IO24RSB0
E7
GDC0/IO32RSB0
J6
IO45RSB1
A9
IO26RSB0
E8
GDA0/IO33RSB0
J7
TCK
B1
IO81RSB1
E9
GDB0/IO34RSB0
J8
TMS
B2
IO04RSB0
F1
IO68RSB1
J9
VPUMP
B3
IO10RSB0
F2
IO67RSB1
B4
IO13RSB0
F3
IO64RSB1
B5
IO15RSB0
F4
GND
B6
IO20RSB0
F5
VCCIB1
B7
IO21RSB0
F6
IO47RSB1
B8
IO28RSB0
F7
IO36RSB0
B9
IO25RSB0
F8
IO38RSB0
C1
IO79RSB1
F9
IO40RSB0
C2
IO80RSB1
G1
IO65RSB1
C3
IO08RSB0
G2
IO66RSB1
C4
IO12RSB0
G3
IO57RSB1
C5
IO17RSB0
G4
IO53RSB1
C6
IO14RSB0
G5
IO49RSB1
C7
IO18RSB0
G6
IO44RSB1
C8
IO29RSB0
G7
IO46RSB1
C9
IO27RSB0
G8
VJTAG
D1
IO74RSB1
G9
TRST
D2
IO76RSB1
H1
IO62RSB1
D3
IO77RSB1
H2
FF/IO60RSB1
D4
VCC
H3
IO58RSB1
D5
VCCIB0
H4
IO54RSB1
D6
GND
H5
IO48RSB1
D7
IO23RSB0
H6
IO43RSB1
D8
IO31RSB0
H7
IO42RSB1
4- 8
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
CS81
CS81
CS81
Pin Number
AGLN060 Function
Pin Number
AGLN060 Function
Pin Number
AGLN060 Function
A1
GAA0/IO02RSB0
D8
GCC1/IO35RSB0
H6
IO56RSB1
GDA2/IO51RSB1
A2
GAA1/IO03RSB0
D9
GCC0/IO36RSB0
H72
A3
GAC0/IO06RSB0
E1
GFB0/IO83RSB1
H8
TDI
A4
IO09RSB0
E2
GFB1/IO84RSB1
H9
TDO
A5
IO13RSB0
E3
GFA1/IO81RSB1
J1
GEA2/IO68RSB1
A6
IO18RSB0
E4
VCCIB1
J2
GEC2/IO66RSB1
A7
GBB0/IO21RSB0
E5
VCC
J3
IO64RSB1
A8
GBA1/IO24RSB0
E6
VCCIB0
J4
IO61RSB1
A9
GBA2/IO25RSB0
E7
GCA1/IO39RSB0
J5
IO58RSB1
B1
GAA2/IO95RSB1
E8
GCA0/IO40RSB0
J6
IO55RSB1
B2
GAB0/IO04RSB0
E9
GCB2/IO42RSB0
J7
TCK
B3
GAC1/IO07RSB0
1
F1
VCCPLF
J8
TMS
B4
IO08RSB0
F21
VCOMPLF
J9
VPUMP
B5
IO15RSB0
F3
GND
B6
GBC0/IO19RSB0
F4
GND
B7
GBB1/IO22RSB0
F5
VCCIB1
B8
IO26RSB0
F6
GND
B9
GBB2/IO27RSB0
F7
GDA1/IO49RSB0
C1
GAB2/IO93RSB1
F8
GDC1/IO45RSB0
C2
IO94RSB1
F9
GDC0/IO46RSB0
C3
GND
G1
GEA0/IO69RSB1
C4
IO10RSB0
G2
GEC1/IO74RSB1
C5
IO17RSB0
G3
GEB1/IO72RSB1
C6
GND
G4
IO63RSB1
C7
GBA0/IO23RSB0
G5
IO60RSB1
C8
GBC2/IO29RSB0
G6
IO54RSB1
C9
IO31RSB0
G7
GDB2/IO52RSB1
D1
GAC2/IO91RSB1
G8
VJTAG
D2
IO92RSB1
G9
TRST
D3
GFA2/IO80RSB1
H1
GEA1/IO70RSB1
D4
VCC
H2
FF/GEB2/IO67RSB1
D5
VCCIB0
H3
IO65RSB1
D6
GND
H4
IO62RSB1
D7
GCC2/IO43RSB0
H5
IO59RSB1
Notes:
1. Pin numbers F1 and F2 must be connected to ground because a PLL is not supported for AGLN060-CS81.
2. The bus hold attribute (hold previous I/O state in Flash*Freeze mode) is not supported for pin H7 in AGLN060-CS81.
R ev i si o n 1 7
4 -9
Package Pin Assignments
CS81
CS81
CS81
Pin Number AGLN060Z Function
Pin Number AGLN060Z Function
Pin Number AGLN060Z Function
A1
GAA0/IO02RSB0
D8
GCC1/IO35RSB0
H6
IO56RSB1
GDA2/IO51RSB1
A2
GAA1/IO03RSB0
D9
GCC0/IO36RSB0
H72
A3
GAC0/IO06RSB0
E1
GFB0/IO83RSB1
H8
TDI
A4
IO09RSB0
E2
GFB1/IO84RSB1
H9
TDO
A5
IO13RSB0
E3
GFA1/IO81RSB1
J1
GEA2/IO68RSB1
A6
IO18RSB0
E4
VCCIB1
J2
GEC2/IO66RSB1
A7
GBB0/IO21RSB0
E5
VCC
J3
IO64RSB1
A8
GBA1/IO24RSB0
E6
VCCIB0
J4
IO61RSB1
A9
GBA2/IO25RSB0
E7
GCA1/IO39RSB0
J5
IO58RSB1
B1
GAA2/IO95RSB1
E8
GCA0/IO40RSB0
J6
IO55RSB1
B2
GAB0/IO04RSB0
E9
GCB2/IO42RSB0
J7
TCK
B3
GAC1/IO07RSB0
1
F1
VCCPLF
J8
TMS
B4
IO08RSB0
F21
VCOMPLF
J9
VPUMP
B5
IO15RSB0
F3
GND
B6
GBC0/IO19RSB0
F4
GND
B7
GBB1/IO22RSB0
F5
VCCIB1
B8
IO26RSB0
F6
GND
B9
GBB2/IO27RSB0
F7
GDA1/IO49RSB0
C1
GAB2/IO93RSB1
F8
GDC1/IO45RSB0
C2
IO94RSB1
F9
GDC0/IO46RSB0
C3
GND
G1
GEA0/IO69RSB1
C4
IO10RSB0
G2
GEC1/IO74RSB1
C5
IO17RSB0
G3
GEB1/IO72RSB1
C6
GND
G4
IO63RSB1
C7
GBA0/IO23RSB0
G5
IO60RSB1
C8
GBC2/IO29RSB0
G6
IO54RSB1
C9
IO31RSB0
G7
GDB2/IO52RSB1
D1
GAC2/IO91RSB1
G8
VJTAG
D2
IO92RSB1
G9
TRST
D3
GFA2/IO80RSB1
H1
GEA1/IO70RSB1
D4
VCC
H2
FF/GEB2/IO67RSB1
D5
VCCIB0
H3
IO65RSB1
D6
GND
H4
IO62RSB1
D7
GCC2/IO43RSB0
H5
IO59RSB1
Notes:
1. Pin numbers F1 and F2 must be connected to ground because a PLL is not supported for AGLN060Z-CS81.
2. The bus hold attribute (hold previous I/O state in Flash*Freeze mode) is not supported for pin H7 in AGLN060Z-CS81.
4- 10
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
CS81
CS81
CS81
Pin Number
AGLN125 Function
Pin Number
AGLN125 Function
Pin Number
AGLN125 Function
A1
GAA0/IO00RSB0
E1
GFB0/IO120RSB1
J1
GEA2/IO103RSB1
A2
GAA1/IO01RSB0
E2
GFB1/IO121RSB1
J2
GEC2/IO101RSB1
A3
GAC0/IO04RSB0
E3
GFA1/IO118RSB1
J3
IO97RSB1
A4
IO13RSB0
E4
VCCIB1
J4
IO93RSB1
A5
IO22RSB0
E5
VCC
J5
IO90RSB1
A6
IO32RSB0
E6
VCCIB0
J6
IO78RSB1
A7
GBB0/IO37RSB0
E7
GCA0/IO56RSB0
J7
TCK
A8
GBA1/IO40RSB0
E8
GCA1/IO55RSB0
J8
TMS
A9
GBA2/IO41RSB0
E9
GCB2/IO58RSB0
J9
VPUMP
B1
GAA2/IO132RSB1
F1*
VCCPLF
B2
GAB0/IO02RSB0
F2*
VCOMPLF
B3
GAC1/IO05RSB0
F3
GND
B4
IO11RSB0
F4
GND
B5
IO25RSB0
F5
VCCIB1
B6
GBC0/IO35RSB0
F6
GND
B7
GBB1/IO38RSB0
F7
GDA1/IO65RSB0
B8
IO42RSB0
F8
GDC1/IO61RSB0
B9
GBB2/IO43RSB0
F9
GDC0/IO62RSB0
C1
GAB2/IO130RSB1
G1
GEA0/IO104RSB1
C2
IO131RSB1
G2
GEC0/IO108RSB1
C3
GND
G3
GEB1/IO107RSB1
C4
IO15RSB0
G4
IO96RSB1
C5
IO28RSB0
G5
IO92RSB1
C6
GND
G6
IO72RSB1
C7
GBA0/IO39RSB0
G7
GDB2/IO68RSB1
C8
GBC2/IO45RSB0
G8
VJTAG
C9
IO47RSB0
G9
TRST
D1
GAC2/IO128RSB1
H1
GEA1/IO105RSB1
D2
IO129RSB1
H2
FF/GEB2/IO102RSB1
D3
GFA2/IO117RSB1
H3
IO99RSB1
D4
VCC
H4
IO94RSB1
D5
VCCIB0
H5
IO91RSB1
D6
GND
H6
IO81RSB1
D7
GCC2/IO59RSB0
H7
GDA2/IO67RSB1
D8
GCC1/IO51RSB0
H8
TDI
D9
GCC0/IO52RSB0
H9
TDO
Note: * Pin numbers F1 and F2 must be connected to ground because a PLL is not supported for AGLN125-CS81.
R ev i si o n 1 7
4- 11
Package Pin Assignments
CS8
CS8
CS8
Pin Number AGLN125Z Function
Pin Number AGLN125Z Function
Pin Number AGLN125Z Function
A1
GAA0/IO00RSB0
E1
GFB0/IO120RSB1
J1
GEA2/IO103RSB1
A2
GAA1/IO01RSB0
E2
GFB1/IO121RSB1
J2
GEC2/IO101RSB1
A3
GAC0/IO04RSB0
E3
GFA1/IO118RSB1
J3
IO97RSB1
A4
IO13RSB0
E4
VCCIB1
J4
IO93RSB1
A5
IO22RSB0
E5
VCC
J5
IO90RSB1
A6
IO32RSB0
E6
VCCIB0
J6
IO78RSB1
A7
GBB0/IO37RSB0
E7
GCA0/IO56RSB0
J7
TCK
A8
GBA1/IO40RSB0
E8
GCA1/IO55RSB0
J8
TMS
A9
GBA2/IO41RSB0
E9
GCB2/IO58RSB0
J9
VPUMP
B1
GAA2/IO132RSB1
F1*
VCCPLF
B2
GAB0/IO02RSB0
F2*
VCOMPLF
B3
GAC1/IO05RSB0
F3
GND
B4
IO11RSB0
F4
GND
B5
IO25RSB0
F5
VCCIB1
B6
GBC0/IO35RSB0
F6
GND
B7
GBB1/IO38RSB0
F7
GDA1/IO65RSB0
B8
IO42RSB0
F8
GDC1/IO61RSB0
B9
GBB2/IO43RSB0
F9
GDC0/IO62RSB0
C1
GAB2/IO130RSB1
G1
GEA0/IO104RSB1
C2
IO131RSB1
G2
GEC0/IO108RSB1
C3
GND
G3
GEB1/IO107RSB1
C4
IO15RSB0
G4
IO96RSB1
C5
IO28RSB0
G5
IO92RSB1
C6
GND
G6
IO72RSB1
C7
GBA0/IO39RSB0
G7
GDB2/IO68RSB1
C8
GBC2/IO45RSB0
G8
VJTAG
C9
IO47RSB0
G9
TRST
D1
GAC2/IO128RSB1
H1
GEA1/IO105RSB1
D2
IO129RSB1
H2
FF/GEB2/IO102RSB1
D3
GFA2/IO117RSB1
H3
IO99RSB1
D4
VCC
H4
IO94RSB1
D5
VCCIB0
H5
IO91RSB1
D6
GND
H6
IO81RSB1
D7
GCC2/IO59RSB0
H7
GDA2/IO67RSB1
D8
GCC1/IO51RSB0
H8
TDI
D9
GCC0/IO52RSB0
H9
TDO
Note: * Pin numbers F1 and F2 must be connected to ground because a PLL is not supported for AGLN125Z-CS81.
4- 12
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
CS81
CS81
CS81
Pin Number
AGLN250 Function
Pin Number
AGLN250 Function
Pin Number
AGLN250 Function
A1
GAA0/IO00RSB0
E1
GFB0/IO109NDB3
J1
GEA2/IO97RSB2
A2
GAA1/IO01RSB0
E2
GFB1/IO109PDB3
J2
GEC2/IO95RSB2
A3
GAC0/IO04RSB0
E3
GFA1/IO108PSB3
J3
IO92RSB2
A4
IO13RSB0
E4
VCCIB3
J4
IO88RSB2
A5
IO21RSB0
E5
VCC
J5
IO84RSB2
A6
IO27RSB0
E6
VCCIB1
J6
IO74RSB2
A7
GBB0/IO37RSB0
E7
GCA0/IO50NDB1
J7
TCK
A8
GBA1/IO40RSB0
E8
GCA1/IO50PDB1
J8
TMS
A9
GBA2/IO41PPB1
E9
GCB2/IO52PPB1
J9
VPUMP
B1
GAA2/IO118UPB3
F1*
VCCPLF
B2
GAB0/IO02RSB0
F2*
VCOMPLF
B3
GAC1/IO05RSB0
F3
GND
B4
IO11RSB0
F4
GND
B5
IO23RSB0
F5
VCCIB2
B6
GBC0/IO35RSB0
F6
GND
B7
GBB1/IO38RSB0
F7
GDA1/IO60USB1
B8
IO41NPB1
F8
GDC1/IO58UDB1
B9
GBB2/IO42PSB1
F9
GDC0/IO58VDB1
C1
GAB2/IO117UPB3
G1
GEA0/IO98NDB3
C2
IO118VPB3
G2
GEC1/IO100PDB3
C3
GND
G3
GEC0/IO100NDB3
C4
IO15RSB0
G4
IO91RSB2
C5
IO25RSB0
G5
IO86RSB2
C6
GND
G6
IO71RSB2
C7
GBA0/IO39RSB0
G7
GDB2/IO62RSB2
C8
GBC2/IO43B1
G8
VJTAG
C9
IO43NDB1
G9
TRST
D1
GAC2/IO116USB3
H1
GEA1/IO98PDB3
D2
IO117VPB3
H2
FF/GEB2/IO96RSB2
D3
GFA2/IO107PSB3
H3
IO93RSB2
D4
VCC
H4
IO90RSB2
D5
VCCIB0
H5
IO85RSB2
D6
GND
H6
IO77RSB2
D7
IO52NPB1
H7
GDA2/IO61RSB2
D8
GCC1/IO48PDB1
H8
TDI
D9
GCC0/IO48NDB1
H9
TDO
Note: * Pin numbers F1 and F2 must be connected to ground because a PLL is not supported for AGLN250-CS81.
R ev i si o n 1 7
4- 13
Package Pin Assignments
CS81
CS81
CS81
Pin Number AGLN250Z Function
Pin Number AGLN250Z Function
Pin Number AGLN250Z Function
A1
GAA0/IO00RSB0
E1
GFB0/IO59RSB3
J1
GEA2/IO50RSB2
A2
GAA1/IO01RSB0
E2
GFB1/IO60RSB3
J2
GEC2/IO48RSB2
A3
GAC0/IO04RSB0
E3
GFA1/IO58RSB3
J3
IO46RSB2
A4
IO07RSB0
E4
VCCIB3
J4
IO43RSB2
A5
IO09RSB0
E5
VCC
J5
IO40RSB2
A6
IO12RSB0
E6
VCCIB1
J6
IO38RSB2
A7
GBB0/IO16RSB0
E7
GCA0/IO28RSB1
J7
TCK
A8
GBA1/IO19RSB0
E8
GCA1/IO27RSB1
J8
TMS
A9
GBA2/IO20RSB1
E9
GCB2/IO29RSB1
J9
VPUMP
B1
GAA2/IO67RSB3
F1*
VCCPLF
B2
GAB0/IO02RSB0
F2*
VCOMPLF
B3
GAC1/IO05RSB0
F3
GND
B4
IO06RSB0
F4
GND
B5
IO10RSB0
F5
VCCIB2
B6
GBC0/IO14RSB0
F6
GND
B7
GBB1/IO17RSB0
F7
GDA1/IO33RSB1
B8
IO21RSB1
F8
GDC1/IO31RSB1
B9
GBB2/IO22RSB1
F9
GDC0/IO32RSB1
C1
GAB2/IO65RSB3
G1
GEA0/IO51RSB3
C2
IO66RSB3
G2
GEC1/IO54RSB3
C3
GND
G3
GEC0/IO53RSB3
C4
IO08RSB0
G4
IO45RSB2
C5
IO11RSB0
G5
IO42RSB2
C6
GND
G6
IO37RSB2
C7
GBA0/IO18RSB0
G7
GDB2/IO35RSB2
C8
GBC2/IO23RSB1
G8
VJTAG
C9
IO24RSB1
G9
TRST
D1
GAC2/IO63RSB3
H1
GEA1/IO52RSB3
D2
IO64RSB3
H2
FF/GEB2/IO49RSB2
D3
GFA2/IO56RSB3
H3
IO47RSB2
D4
VCC
H4
IO44RSB2
D5
VCCIB0
H5
IO41RSB2
D6
GND
H6
IO39RSB2
D7
IO30RSB1
H7
GDA2/IO34RSB2
D8
GCC1/IO25RSB1
H8
TDI
D9
GCC0/IO26RSB1
H9
TDO
Note: * Pin numbers F1 and F2 must be connected to ground because a PLL is not supported for AGLN250Z-CS81.
4- 14
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
QN48
Pin 1
48
1
Notes:
1. This is the bottom view of the package.
2. The die attach paddle of the package is tied to ground (GND).
Note
For Package Manufacturing and Environmental information, visit the Resource Center at
http://www.microsemi.com/soc/products/solutions/package/docs.aspx.
R ev i si o n 1 7
4- 15
Package Pin Assignments
QN48
QN48
Pin Number
AGLN010
Function
Pin Number
AGLN010
Function
1
GEC0/IO37RSB1
36
IO07RSB0
2
IO36RSB1
37
IO06RSB0
3
GEA0/IO34RSB1
38
GDA0/IO05RSB0
4
IO22RSB1
39
IO03RSB0
5
GND
40
GDC0/IO01RSB0
6
VCCIB1
41
IO12RSB1
7
IO24RSB1
42
IO13RSB1
8
IO33RSB1
43
IO15RSB1
9
IO26RSB1
44
IO16RSB1
10
IO32RSB1
45
IO18RSB1
11
IO27RSB1
46
IO19RSB1
12
IO29RSB1
47
IO20RSB1
13
IO30RSB1
48
IO21RSB1
14
FF/IO31RSB1
15
IO28RSB1
16
IO25RSB1
17
IO23RSB1
18
VCC
19
VCCIB1
20
IO17RSB1
21
IO14RSB1
22
TCK
23
TDI
24
TMS
25
VPUMP
26
TDO
27
TRST
28
VJTAG
29
IO11RSB0
30
IO10RSB0
31
IO09RSB0
32
IO08RSB0
33
VCCIB0
34
GND
35
VCC
4- 16
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
QN48
QN48
Pin Number AGLN030Z Function
Pin Number AGLN030Z Function
1
IO82RSB1
37
IO24RSB0
2
GEC0/IO73RSB1
38
IO22RSB0
3
GEA0/IO72RSB1
39
IO20RSB0
4
GEB0/IO71RSB1
40
IO18RSB0
5
GND
41
IO16RSB0
6
VCCIB1
42
IO14RSB0
7
IO68RSB1
43
IO10RSB0
8
IO67RSB1
44
IO08RSB0
9
IO66RSB1
45
IO06RSB0
10
IO65RSB1
46
IO04RSB0
11
IO64RSB1
47
IO02RSB0
12
IO62RSB1
48
IO00RSB0
13
IO61RSB1
14
FF/IO60RSB1
15
IO57RSB1
16
IO55RSB1
17
IO53RSB1
18
VCC
19
VCCIB1
20
IO46RSB1
21
IO42RSB1
22
TCK
23
TDI
24
TMS
25
VPUMP
26
TDO
27
TRST
28
VJTAG
29
IO38RSB0
30
GDB0/IO34RSB0
31
GDA0/IO33RSB0
32
GDC0/IO32RSB0
33
VCCIB0
34
GND
35
VCC
36
IO25RSB0
R ev i si o n 1 7
4- 17
Package Pin Assignments
QN68
Pin A1 Mark
68
1
Notes:
1. This is the bottom view of the package.
2. The die attach paddle of the package is tied to ground (GND).
Note
For Package Manufacturing and Environmental information, visit the Resource Center at
http://www.microsemi.com/soc/products/solutions/package/docs.aspx.
4- 18
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
QN68
QN68
Pin Number
AGLN015
Function
Pin Number
AGLN015
Function
1
IO60RSB2
36
TDO
2
IO54RSB2
37
TRST
3
IO52RSB2
38
VJTAG
4
IO50RSB2
39
IO17RSB0
5
IO49RSB2
40
IO16RSB0
6
GEC0/IO48RSB2
41
GDA0/IO15RSB0
7
GEA0/IO47RSB2
42
GDC0/IO14RSB0
8
VCC
43
IO13RSB0
9
GND
44
VCCIB0
10
VCCIB2
45
GND
11
IO46RSB2
46
VCC
12
IO45RSB2
47
IO12RSB0
13
IO44RSB2
48
IO11RSB0
14
IO43RSB2
49
IO09RSB0
15
IO42RSB2
50
IO05RSB0
16
IO41RSB2
51
IO00RSB0
17
IO40RSB2
52
IO07RSB0
18
FF/IO39RSB1
53
IO03RSB0
19
IO37RSB1
54
IO18RSB1
20
IO35RSB1
55
IO20RSB1
21
IO33RSB1
56
IO22RSB1
22
IO31RSB1
57
IO24RSB1
23
IO30RSB1
58
IO28RSB1
24
VCC
59
NC
25
GND
60
GND
26
VCCIB1
61
NC
27
IO27RSB1
62
IO32RSB1
28
IO25RSB1
63
IO34RSB1
29
IO23RSB1
64
IO36RSB1
30
IO21RSB1
65
IO61RSB2
31
IO19RSB1
66
IO58RSB2
32
TCK
67
IO56RSB2
33
TDI
68
IO63RSB2
34
TMS
35
VPUMP
R ev i si o n 1 7
4- 19
Package Pin Assignments
QN68
QN68
Pin Number
AGLN020
Function
Pin Number
AGLN020
Function
1
IO60RSB2
36
TDO
2
IO54RSB2
37
TRST
3
IO52RSB2
38
VJTAG
4
IO50RSB2
39
IO17RSB0
5
IO49RSB2
40
IO16RSB0
6
GEC0/IO48RSB2
41
GDA0/IO15RSB0
7
GEA0/IO47RSB2
42
GDC0/IO14RSB0
8
VCC
43
IO13RSB0
9
GND
44
VCCIB0
10
VCCIB2
45
GND
11
IO46RSB2
46
VCC
12
IO45RSB2
47
IO12RSB0
13
IO44RSB2
48
IO11RSB0
14
IO43RSB2
49
IO09RSB0
15
IO42RSB2
50
IO05RSB0
16
IO41RSB2
51
IO00RSB0
17
IO40RSB2
52
IO07RSB0
18
FF/IO39RSB1
53
IO03RSB0
19
IO37RSB1
54
IO18RSB1
20
IO35RSB1
55
IO20RSB1
21
IO33RSB1
56
IO22RSB1
22
IO31RSB1
57
IO24RSB1
23
IO30RSB1
58
IO28RSB1
24
VCC
59
NC
25
GND
60
GND
26
VCCIB1
61
NC
27
IO27RSB1
62
IO32RSB1
28
IO25RSB1
63
IO34RSB1
29
IO23RSB1
64
IO36RSB1
30
IO21RSB1
65
IO61RSB2
31
IO19RSB1
66
IO58RSB2
32
TCK
67
IO56RSB2
33
TDI
68
IO63RSB2
34
TMS
35
VPUMP
4- 20
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
QN68
QN68
Pin Number
AGLN030Z
Function
Pin Number
AGLN030Z
Function
1
IO82RSB1
36
TDO
2
IO80RSB1
37
TRST
3
IO78RSB1
38
VJTAG
4
IO76RSB1
39
IO40RSB0
5
GEC0/IO73RSB1
40
IO37RSB0
6
GEA0/IO72RSB1
41
GDB0/IO34RSB0
7
GEB0/IO71RSB1
42
GDA0/IO33RSB0
8
VCC
43
GDC0/IO32RSB0
9
GND
44
VCCIB0
10
VCCIB1
45
GND
11
IO68RSB1
46
VCC
12
IO67RSB1
47
IO31RSB0
13
IO66RSB1
48
IO29RSB0
14
IO65RSB1
49
IO28RSB0
15
IO64RSB1
50
IO27RSB0
16
IO63RSB1
51
IO25RSB0
17
IO62RSB1
52
IO24RSB0
18
FF/IO60RSB1
53
IO22RSB0
19
IO58RSB1
54
IO21RSB0
20
IO56RSB1
55
IO19RSB0
21
IO54RSB1
56
IO17RSB0
22
IO52RSB1
57
IO15RSB0
23
IO51RSB1
58
IO14RSB0
24
VCC
59
VCCIB0
25
GND
60
GND
26
VCCIB1
61
VCC
27
IO50RSB1
62
IO12RSB0
28
IO48RSB1
63
IO10RSB0
29
IO46RSB1
64
IO08RSB0
30
IO44RSB1
65
IO06RSB0
31
IO42RSB1
66
IO04RSB0
32
TCK
67
IO02RSB0
33
TDI
68
IO00RSB0
34
TMS
35
VPUMP
R ev i si o n 1 7
4- 21
Package Pin Assignments
VQ100
100
1
Note: This is the top view of the package.
Note
For Package Manufacturing and Environmental information, visit the Resource Center at
http://www.microsemi.com/soc/products/solutions/package/docs.aspx.
4- 22
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
VQ100
VQ100
VQ100
Pin Number
AGLN030Z
Function
Pin Number
AGLN030Z
Function
Pin Number
AGLN030Z
Function
1
GND
36
IO51RSB1
71
IO29RSB0
2
IO82RSB1
37
VCC
72
IO28RSB0
3
IO81RSB1
38
GND
73
IO27RSB0
4
IO80RSB1
39
VCCIB1
74
IO26RSB0
5
IO79RSB1
40
IO49RSB1
75
IO25RSB0
6
IO78RSB1
41
IO47RSB1
76
IO24RSB0
7
IO77RSB1
42
IO46RSB1
77
IO23RSB0
8
IO76RSB1
43
IO45RSB1
78
IO22RSB0
9
GND
44
IO44RSB1
79
IO21RSB0
10
IO75RSB1
45
IO43RSB1
80
IO20RSB0
11
IO74RSB1
46
IO42RSB1
81
IO19RSB0
12
GEC0/IO73RSB1
47
TCK
82
IO18RSB0
13
GEA0/IO72RSB1
48
TDI
83
IO17RSB0
14
GEB0/IO71RSB1
49
TMS
84
IO16RSB0
15
IO70RSB1
50
NC
85
IO15RSB0
16
IO69RSB1
51
GND
86
IO14RSB0
17
VCC
52
VPUMP
87
VCCIB0
18
VCCIB1
53
NC
88
GND
19
IO68RSB1
54
TDO
89
VCC
20
IO67RSB1
55
TRST
90
IO12RSB0
21
IO66RSB1
56
VJTAG
91
IO10RSB0
22
IO65RSB1
57
IO41RSB0
92
IO08RSB0
23
IO64RSB1
58
IO40RSB0
93
IO07RSB0
24
IO63RSB1
59
IO39RSB0
94
IO06RSB0
25
IO62RSB1
60
IO38RSB0
95
IO05RSB0
26
IO61RSB1
61
IO37RSB0
96
IO04RSB0
27
FF/IO60RSB1
62
IO36RSB0
97
IO03RSB0
28
IO59RSB1
63
GDB0/IO34RSB0
98
IO02RSB0
29
IO58RSB1
64
GDA0/IO33RSB0
99
IO01RSB0
30
IO57RSB1
65
GDC0/IO32RSB0
100
IO00RSB0
31
IO56RSB1
66
VCCIB0
32
IO55RSB1
67
GND
33
IO54RSB1
68
VCC
34
IO53RSB1
69
IO31RSB0
35
IO52RSB1
70
IO30RSB0
R ev i si o n 1 7
4- 23
Package Pin Assignments
VQ100
VQ100
VQ100
Pin Number
AGLN060 Function
Pin Number
AGLN060 Function
Pin Number
AGLN060 Function
1
GND
36
IO61RSB1
71
GBB2/IO27RSB0
2
GAA2/IO51RSB1
37
VCC
72
IO26RSB0
3
IO52RSB1
38
GND
73
GBA2/IO25RSB0
4
GAB2/IO53RSB1
39
VCCIB1
74
VMV0
5
IO95RSB1
40
IO60RSB1
75
GNDQ
6
GAC2/IO94RSB1
41
IO59RSB1
76
GBA1/IO24RSB0
7
IO93RSB1
42
IO58RSB1
77
GBA0/IO23RSB0
8
IO92RSB1
43
IO57RSB1
78
GBB1/IO22RSB0
9
GND
44
GDC2/IO56RSB1
79
GBB0/IO21RSB0
10
GFB1/IO87RSB1
45*
GDB2/IO55RSB1
80
GBC1/IO20RSB0
11
GFB0/IO86RSB1
46
GDA2/IO54RSB1
81
GBC0/IO19RSB0
12
VCOMPLF
47
TCK
82
IO18RSB0
13
GFA0/IO85RSB1
48
TDI
83
IO17RSB0
14
VCCPLF
49
TMS
84
IO15RSB0
15
GFA1/IO84RSB1
50
VMV1
85
IO13RSB0
16
GFA2/IO83RSB1
51
GND
86
IO11RSB0
17
VCC
52
VPUMP
87
VCCIB0
18
VCCIB1
53
NC
88
GND
19
GEC1/IO77RSB1
54
TDO
89
VCC
20
GEB1/IO75RSB1
55
TRST
90
IO10RSB0
21
GEB0/IO74RSB1
56
VJTAG
91
IO09RSB0
22
GEA1/IO73RSB1
57
GDA1/IO49RSB0
92
IO08RSB0
23
GEA0/IO72RSB1
58
GDC0/IO46RSB0
93
GAC1/IO07RSB0
24
VMV1
59
GDC1/IO45RSB0
94
GAC0/IO06RSB0
25
GNDQ
60
GCC2/IO43RSB0
95
GAB1/IO05RSB0
26
GEA2/IO71RSB1
61
GCB2/IO42RSB0
96
GAB0/IO04RSB0
27
FF/GEB2/IO70RSB1
62
GCA0/IO40RSB0
97
GAA1/IO03RSB0
28
GEC2/IO69RSB1
63
GCA1/IO39RSB0
98
GAA0/IO02RSB0
29
IO68RSB1
64
GCC0/IO36RSB0
99
IO01RSB0
30
IO67RSB1
65
GCC1/IO35RSB0
100
IO00RSB0
31
IO66RSB1
66
VCCIB0
32
IO65RSB1
67
GND
33
IO64RSB1
68
VCC
34
IO63RSB1
69
IO31RSB0
35
IO62RSB1
70
GBC2/IO29RSB0
Note: *The bus hold attribute (hold previous I/O state in Flash*Freeze mode) is not supported for pin 45 in AGLN060VQ100.
4- 24
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
VQ100
VQ100
VQ100
Pin Number AGLN060Z Function
Pin Number AGLN060Z Function
Pin Number AGLN060Z Function
1
GND
35
IO62RSB1
69
IO31RSB0
2
GAA2/IO51RSB1
36
IO61RSB1
70
GBC2/IO29RSB0
3
IO52RSB1
37
VCC
71
GBB2/IO27RSB0
4
GAB2/IO53RSB1
38
GND
72
IO26RSB0
5
IO95RSB1
39
VCCIB1
73
GBA2/IO25RSB0
6
GAC2/IO94RSB1
40
IO60RSB1
74
VMV0
7
IO93RSB1
41
IO59RSB1
75
GNDQ
8
IO92RSB1
42
IO58RSB1
76
GBA1/IO24RSB0
9
GND
43
IO57RSB1
77
GBA0/IO23RSB0
10
GFB1/IO87RSB1
44
GDC2/IO56RSB1
78
GBB1/IO22RSB0
11
GFB0/IO86RSB1
45*
GDB2/IO55RSB1
79
GBB0/IO21RSB0
12
VCOMPLF
46
GDA2/IO54RSB1
80
GBC1/IO20RSB0
13
GFA0/IO85RSB1
47
TCK
81
GBC0/IO19RSB0
14
VCCPLF
48
TDI
82
IO18RSB0
15
GFA1/IO84RSB1
49
TMS
83
IO17RSB0
16
GFA2/IO83RSB1
50
VMV1
84
IO15RSB0
17
VCC
51
GND
85
IO13RSB0
18
VCCIB1
52
VPUMP
86
IO11RSB0
19
GEC1/IO77RSB1
53
NC
87
VCCIB0
20
GEB1/IO75RSB1
54
TDO
88
GND
21
GEB0/IO74RSB1
55
TRST
89
VCC
22
GEA1/IO73RSB1
56
VJTAG
90
IO10RSB0
23
GEA0/IO72RSB1
57
GDA1/IO49RSB0
91
IO09RSB0
24
VMV1
58
GDC0/IO46RSB0
92
IO08RSB0
25
GNDQ
59
GDC1/IO45RSB0
93
GAC1/IO07RSB0
26
GEA2/IO71RSB1
60
GCC2/IO43RSB0
94
GAC0/IO06RSB0
27
FF/GEB2/IO70RSB1
61
GCB2/IO42RSB0
95
GAB1/IO05RSB0
28
GEC2/IO69RSB1
62
GCA0/IO40RSB0
96
GAB0/IO04RSB0
29
IO68RSB1
63
GCA1/IO39RSB0
97
GAA1/IO03RSB0
30
IO67RSB1
64
GCC0/IO36RSB0
98
GAA0/IO02RSB0
31
IO66RSB1
65
GCC1/IO35RSB0
99
IO01RSB0
32
IO65RSB1
66
VCCIB0
100
IO00RSB0
33
IO64RSB1
67
GND
34
IO63RSB1
68
VCC
Note: *The bus hold attribute (hold previous I/O state in Flash*Freeze mode) is not supported for pin 45 in AGLN060ZVQ100.
R ev i si o n 1 7
4- 25
Package Pin Assignments
VQ100
VQ100
VQ100
Pin Number
AGLN125 Function
Pin Number
AGLN125 Function
Pin Number
AGLN125 Function
1
GND
37
VCC
73
GBA2/IO41RSB0
2
GAA2/IO67RSB1
38
GND
74
VMV0
3
IO68RSB1
39
VCCIB1
75
GNDQ
4
GAB2/IO69RSB1
40
IO87RSB1
76
GBA1/IO40RSB0
5
IO132RSB1
41
IO84RSB1
77
GBA0/IO39RSB0
6
GAC2/IO131RSB1
42
IO81RSB1
78
GBB1/IO38RSB0
7
IO130RSB1
43
IO75RSB1
79
GBB0/IO37RSB0
8
IO129RSB1
44
GDC2/IO72RSB1
80
GBC1/IO36RSB0
9
GND
45
GDB2/IO71RSB1
81
GBC0/IO35RSB0
10
GFB1/IO124RSB1
46
GDA2/IO70RSB1
82
IO32RSB0
11
GFB0/IO123RSB1
47
TCK
83
IO28RSB0
12
VCOMPLF
48
TDI
84
IO25RSB0
13
GFA0/IO122RSB1
49
TMS
85
IO22RSB0
14
VCCPLF
50
VMV1
86
IO19RSB0
15
GFA1/IO121RSB1
51
GND
87
VCCIB0
16
GFA2/IO120RSB1
52
VPUMP
88
GND
17
VCC
53
NC
89
VCC
18
VCCIB1
54
TDO
90
IO15RSB0
19
GEC0/IO111RSB1
55
TRST
91
IO13RSB0
20
GEB1/IO110RSB1
56
VJTAG
92
IO11RSB0
21
GEB0/IO109RSB1
57
GDA1/IO65RSB0
93
IO09RSB0
22
GEA1/IO108RSB1
58
GDC0/IO62RSB0
94
IO07RSB0
23
GEA0/IO107RSB1
59
GDC1/IO61RSB0
95
GAC1/IO05RSB0
24
VMV1
60
GCC2/IO59RSB0
96
GAC0/IO04RSB0
25
GNDQ
61
GCB2/IO58RSB0
97
GAB1/IO03RSB0
26
GEA2/IO106RSB1
62
GCA0/IO56RSB0
98
GAB0/IO02RSB0
27
FF/GEB2/IO105RSB1
63
GCA1/IO55RSB0
99
GAA1/IO01RSB0
28
GEC2/IO104RSB1
64
GCC0/IO52RSB0
100
GAA0/IO00RSB0
29
IO102RSB1
65
GCC1/IO51RSB0
30
IO100RSB1
66
VCCIB0
31
IO99RSB1
67
GND
32
IO97RSB1
68
VCC
33
IO96RSB1
69
IO47RSB0
34
IO95RSB1
70
GBC2/IO45RSB0
35
IO94RSB1
71
GBB2/IO43RSB0
36
IO93RSB1
72
IO42RSB0
4- 26
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
VQ100
VQ100
VQ100
Pin
Number
AGLN125Z Function
Pin
Number
AGLN125Z Function
Pin
Number
AGLN125Z Function
1
GND
36
IO93RSB1
71
GBB2/IO43RSB0
2
GAA2/IO67RSB1
37
VCC
72
IO42RSB0
3
IO68RSB1
38
GND
73
GBA2/IO41RSB0
4
GAB2/IO69RSB1
39
VCCIB1
74
VMV0
5
IO132RSB1
40
IO87RSB1
75
GNDQ
6
GAC2/IO131RSB1
41
IO84RSB1
76
GBA1/IO40RSB0
7
IO130RSB1
42
IO81RSB1
77
GBA0/IO39RSB0
8
IO129RSB1
43
IO75RSB1
78
GBB1/IO38RSB0
9
GND
44
GDC2/IO72RSB1
79
GBB0/IO37RSB0
10
GFB1/IO124RSB1
45
GDB2/IO71RSB1
80
GBC1/IO36RSB0
11
GFB0/IO123RSB1
46
GDA2/IO70RSB1
81
GBC0/IO35RSB0
12
VCOMPLF
47
TCK
82
IO32RSB0
13
GFA0/IO122RSB1
48
TDI
83
IO28RSB0
14
VCCPLF
49
TMS
84
IO25RSB0
15
GFA1/IO121RSB1
50
VMV1
85
IO22RSB0
16
GFA2/IO120RSB1
51
GND
86
IO19RSB0
17
VCC
52
VPUMP
87
VCCIB0
18
VCCIB1
53
NC
88
GND
19
GEC0/IO111RSB1
54
TDO
89
VCC
20
GEB1/IO110RSB1
55
TRST
90
IO15RSB0
21
GEB0/IO109RSB1
56
VJTAG
91
IO13RSB0
22
GEA1/IO108RSB1
57
GDA1/IO65RSB0
92
IO11RSB0
23
GEA0/IO107RSB1
58
GDC0/IO62RSB0
93
IO09RSB0
24
VMV1
59
GDC1/IO61RSB0
94
IO07RSB0
25
GNDQ
60
GCC2/IO59RSB0
95
GAC1/IO05RSB0
26
GEA2/IO106RSB1
61
GCB2/IO58RSB0
96
GAC0/IO04RSB0
27
FF/GEB2/IO105RSB1
62
GCA0/IO56RSB0
97
GAB1/IO03RSB0
28
GEC2/IO104RSB1
63
GCA1/IO55RSB0
98
GAB0/IO02RSB0
29
IO102RSB1
64
GCC0/IO52RSB0
99
GAA1/IO01RSB0
30
IO100RSB1
65
GCC1/IO51RSB0
100
GAA0/IO00RSB0
31
IO99RSB1
66
VCCIB0
32
IO97RSB1
67
GND
33
IO96RSB1
68
VCC
34
IO95RSB1
69
IO47RSB0
35
IO94RSB1
70
GBC2/IO45RSB0
R ev i si o n 1 7
4- 27
Package Pin Assignments
VQ100
VQ100
VQ100
Pin Number
AGLN250 Function
Pin Number
AGLN250 Function
Pin Number
AGLN250 Function
1
GND
37
VCC
73
GBA2/IO20RSB1
2
GAA2/IO67RSB3
38
GND
74
VMV1
3
IO66RSB3
39
VCCIB2
75
GNDQ
4
GAB2/IO65RSB3
40
IO39RSB2
76
GBA1/IO19RSB0
5
IO64RSB3
41
IO38RSB2
77
GBA0/IO18RSB0
6
GAC2/IO63RSB3
42
IO37RSB2
78
GBB1/IO17RSB0
7
IO62RSB3
43
GDC2/IO36RSB2
79
GBB0/IO16RSB0
8
IO61RSB3
44
GDB2/IO35RSB2
80
GBC1/IO15RSB0
9
GND
45
GDA2/IO34RSB2
81
GBC0/IO14RSB0
10
GFB1/IO60RSB3
46
GNDQ
82
IO13RSB0
11
GFB0/IO59RSB3
47
TCK
83
IO12RSB0
12
VCOMPLF
48
TDI
84
IO11RSB0
13
GFA0/IO57RSB3
49
TMS
85
IO10RSB0
14
VCCPLF
50
VMV2
86
IO09RSB0
15
GFA1/IO58RSB3
51
GND
87
VCCIB0
16
GFA2/IO56RSB3
52
VPUMP
88
GND
17
VCC
53
NC
89
VCC
18
VCCIB3
54
TDO
90
IO08RSB0
19
GFC2/IO55RSB3
55
TRST
91
IO07RSB0
20
GEC1/IO54RSB3
56
VJTAG
92
IO06RSB0
21
GEC0/IO53RSB3
57
GDA1/IO33RSB1
93
GAC1/IO05RSB0
22
GEA1/IO52RSB3
58
GDC0/IO32RSB1
94
GAC0/IO04RSB0
23
GEA0/IO51RSB3
59
GDC1/IO31RSB1
95
GAB1/IO03RSB0
24
VMV3
60
IO30RSB1
96
GAB0/IO02RSB0
25
GNDQ
61
GCB2/IO29RSB1
97
GAA1/IO01RSB0
26
GEA2/IO50RSB2
62
GCA1/IO27RSB1
98
GAA0/IO00RSB0
27
FF/GEB2/IO49RSB2
63
GCA0/IO28RSB1
99
GNDQ
28
GEC2/IO48RSB2
64
GCC0/IO26RSB1
100
VMV0
29
IO47RSB2
65
GCC1/IO25RSB1
30
IO46RSB2
66
VCCIB1
31
IO45RSB2
67
GND
32
IO44RSB2
68
VCC
33
IO43RSB2
69
IO24RSB1
34
IO42RSB2
70
GBC2/IO23RSB1
35
IO41RSB2
71
GBB2/IO22RSB1
36
IO40RSB2
72
IO21RSB1
4- 28
R ev i sio n 1 7
IGLOO nano Low Power Flash FPGAs
VQ100
VQ100
VQ100
Pin Number AGLN250Z Function
Pin Number AGLN250Z Function
Pin Number AGLN250Z Function
1
GND
37
VCC
73
GBA2/IO20RSB1
2
GAA2/IO67RSB3
38
GND
74
VMV1
3
IO66RSB3
39
VCCIB2
75
GNDQ
4
GAB2/IO65RSB3
40
IO39RSB2
76
GBA1/IO19RSB0
5
IO64RSB3
41
IO38RSB2
77
GBA0/IO18RSB0
6
GAC2/IO63RSB3
42
IO37RSB2
78
GBB1/IO17RSB0
7
IO62RSB3
43
GDC2/IO36RSB2
79
GBB0/IO16RSB0
8
IO61RSB3
44
GDB2/IO35RSB2
80
GBC1/IO15RSB0
9
GND
45
GDA2/IO34RSB2
81
GBC0/IO14RSB0
10
GFB1/IO60RSB3
46
GNDQ
82
IO13RSB0
11
GFB0/IO59RSB3
47
TCK
83
IO12RSB0
12
VCOMPLF
48
TDI
84
IO11RSB0
13
GFA0/IO57RSB3
49
TMS
85
IO10RSB0
14
VCCPLF
50
VMV2
86
IO09RSB0
15
GFA1/IO58RSB3
51
GND
87
VCCIB0
16
GFA2/IO56RSB3
52
VPUMP
88
GND
17
VCC
53
NC
89
VCC
18
VCCIB3
54
TDO
90
IO08RSB0
19
GFC2/IO55RSB3
55
TRST
91
IO07RSB0
20
GEC1/IO54RSB3
56
VJTAG
92
IO06RSB0
21
GEC0/IO53RSB3
57
GDA1/IO33RSB1
93
GAC1/IO05RSB0
22
GEA1/IO52RSB3
58
GDC0/IO32RSB1
94
GAC0/IO04RSB0
23
GEA0/IO51RSB3
59
GDC1/IO31RSB1
95
GAB1/IO03RSB0
24
VMV3
60
IO30RSB1
96
GAB0/IO02RSB0
25
GNDQ
61
GCB2/IO29RSB1
97
GAA1/IO01RSB0
26
GEA2/IO50RSB2
62
GCA1/IO27RSB1
98
GAA0/IO00RSB0
27
FF/GEB2/IO49RSB2
63
GCA0/IO28RSB1
99
GNDQ
28
GEC2/IO48RSB2
64
GCC0/IO26RSB1
100
VMV0
29
IO47RSB2
65
GCC1/IO25RSB1
30
IO46RSB2
66
VCCIB1
31
IO45RSB2
67
GND
32
IO44RSB2
68
VCC
33
IO43RSB2
69
IO24RSB1
34
IO42RSB2
70
GBC2/IO23RSB1
35
IO41RSB2
71
GBB2/IO22RSB1
36
IO40RSB2
72
IO21RSB1
R ev i si o n 1 7
4- 29
5 – Datasheet Information
List of Changes
The following table lists critical changes that were made in each version of the IGLOO nano datasheet.
Revision
Revision 17
(May 2013)
Changes
Page
Deleted details related to Ambient temperature from "Enhanced Commercial I, III, IV,
Temperature Range", "IGLOO nano Ordering Information", "Temperature Grade and 2-2
Offerings", and Table 2-2 • Recommended Operating Conditions 1 to remove ambiguities
arising due to the same, and modified Note 2 (SAR 47063).
Revision 16
The "IGLOO nano Ordering Information" section has been updated to mention "Y" as
(December 2012) "Blank" mentioning "Device Does Not Include License to Implement IP Based on the
Cryptography Research, Inc. (CRI) Patent Portfolio" (SAR 43174).
The note in Table 2-100 • IGLOO nano CCC/PLL Specification and Table 2-101 • IGLOO
nano CCC/PLL Specification referring the reader to SmartGen was revised to refer
instead to the online help associated with the core (SAR 42565).
Live at Power-Up (LAPU) has been replaced with ’Instant On’.
Revision 15
The status of the AGLN125 device has been modified from ’Advance’ to ’Production’ in
(September 2012) the "IGLOO nano Device Status" section (SAR 41416).
III
2-70,
2-71
NA
II
Libero Integrated Design Environment (IDE) was changed to Libero System-on-Chip
(SoC) throughout the document (SAR 40274).
NA
Revision 14
The "Security" section was modified to clarify that Microsemi does not support read-back
(September 2012) of programmed data.
1-2
Revision 13
(June 2012)
Figure Figure 2-34 • FIFO Read and Figure 2-35 • FIFO Write have been added (SAR
34842).
2-82
The following sentence was removed from the "VMVx I/O Supply Voltage (quiet)" section
in the "Pin Descriptions" section: "Within the package, the VMV plane is decoupled from
the simultaneous switching noise originating from the output buffer VCCI domain" and
replaced with “Within the package, the VMV plane biases the input stage of the I/Os in
the I/O banks” (SAR 38319). The datasheet mentions that "VMV pins must be connected
to the corresponding VCCI pins" for an ESD enhancement.
3-1
The "In-System Programming (ISP) and Security" section and "Security" section were
revised to clarify that although no existing security measures can give an absolute
guarantee, Microsemi FPGAs implement the best security available in the industry (SAR
34663).
I, 1-2
Notes indicating that AGLN015 is not recommended for new designs have been added
(SAR 35759).
II, III
Revision 12
(March 2012)
Notes indicating that nano-Z devices are not recommended for new designs have been
added. The "Devices Not Recommended For New Designs" section is new (SAR
36759).
The Y security option and Licensed DPA Logo were added to the "IGLOO nano Ordering
Information" section. The trademarked Licensed DPA Logo identifies that a product is
covered by a DPA counter-measures license from Cryptography Research (SAR 34722).
III
The following sentence was removed from the "Advanced Architecture" section: "In
addition, extensive on-chip programming circuitry enables rapid, single-voltage (3.3 V)
programming of IGLOO nano devices via an IEEE 1532 JTAG interface" (SAR 34683).
1-3
R ev i si o n 1 7
5 -1
Datasheet Information
Revision
Revision 12
(continued)
Changes
Page
The "Specifying I/O States During Programming" section is new (SAR 34694).
1-9
The reference to guidelines for global spines and VersaTile rows, given in the "Global
Clock Contribution—PCLOCK" section, was corrected to the "Spine Architecture"
section of the Global Resources chapter in the IGLOO nano FPGA Fabric User's
Guide (SAR 34732).
2-12
Figure 2-4 has been modified for DIN waveform; the Rise and Fall time label has been
changed to tDIN (37106).
2-16
The AC Loading figures in the "Single-Ended I/O Characteristics" section were updated
to match tables in the "Summary of I/O Timing Characteristics – Default I/O Software
Settings" section (SAR 34885).
2-26,
2-20
The notes regarding drive strength in the "Summary of I/O Timing Characteristics –
Default I/O Software Settings" section, "3.3 V LVCMOS Wide Range" section and "1.2 V
LVCMOS Wide Range" section tables were revised for clarification. They now state that
the minimum drive strength for the default software configuration when run in wide range
is ±100 µA. The drive strength displayed in software is supported in normal range only.
For a detailed I/V curve, refer to the IBIS models (SAR 34765).
2-20,
2-29,
2-40
Added values for minimum pulse width and removed the FRMAX row from Table 2-88 2-64 to
through Table 2-99 in the "Global Tree Timing Characteristics" section. Use the software 2-69
to determine the FRMAX for the device you are using (SAR 36953).
Table 2-100 • IGLOO nano CCC/PLL Specification and Table 2-101 • IGLOO nano
CCC/PLL Specification were updated. A note was added indicating that when the
CCC/PLL core is generated by Mircosemi core generator software, not all delay values
of the specified delay increments are available (SAR 34817).
2-70
and
2-71
The port names in the SRAM "Timing Waveforms", SRAM "Timing Characteristics"
tables, Figure 2-36 • FIFO Reset, and the FIFO "Timing Characteristics" tables were
revised to ensure consistency with the software names (SAR 35754).
2-74,
2-77,
2-85
Reference was made to a new application note, Simultaneous Read-Write Operations in
Dual-Port SRAM for Flash-Based cSoCs and FPGAs, which covers these cases in detail
(SAR 34865).
Revision 11
(Jul 2010)
July 2010
5- 2
The "Pin Descriptions" chapter has been added (SAR 34770).
3-1
Package names used in the "Package Pin Assignments" section were revised to match
standards given in Package Mechanical Drawings (SAR 34770).
4-1
The status of the AGLN060 device has changed from Advance to Production.
II
The values for PAC1, PAC2, PAC3, and PAC4 were updated in Table 2-15 • Different
Components Contributing to Dynamic Power Consumption in IGLOO nano Devices for
1.5 V core supply voltage (SAR 26404).
2-10
The values for PAC1, PAC2, PAC3, and PAC4 were updated in Table 2-17 • Different
Components Contributing to Dynamic Power Consumption in IGLOO nano Devices for
1.2 V core supply voltage (SAR 26404).
2-11
The versioning system for datasheets has been changed. Datasheets are assigned a
revision number that increments each time the datasheet is revised. The "IGLOO nano
Device Status" table on page II indicates the status for each device in the device family.
N/A
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
Revision
Revision 10
(Apr 2010)
Changes
Page
References to differential inputs were removed from the datasheet, since IGLOO nano
devices do not support differential inputs (SAR 21449).
N/A
A parenthetical note, "hold previous I/O state in Flash*Freeze mode," was added to each
occurrence of bus hold in the datasheet (SAR 24079).
N/A
The "In-System Programming (ISP) and Security" section was revised to add 1.2 V
programming.
I
The note connected with the "IGLOO nano Ordering Information" table was revised to
clarify features not available for Z feature grade devices.
III
The "IGLOO nano Device Status" table is new.
II
The definition of C in the "Temperature Grade Offerings" table was changed to "extended
commercial temperature range."
IV
1.2 V wide range was added to the list of voltage ranges in the "I/Os with Advanced I/O
Standards" section.
1-8
A note was added to Table 2-2 • Recommended Operating Conditions 1 regarding
switching from 1.2 V to 1.5 V core voltage for in-system programming. The VJTAG
voltage was changed from "1.425 to 3.6" to "1.4 to 3.6" (SAR 24052). The note regarding
voltage for programming V2 and V5 devices was revised (SAR 25213). The maximum
value for VPUMP programming voltage (operation mode) was changed from 3.45 V to
3.6 V (SAR 25220).
2-2
Table 2-6 • Temperature and Voltage Derating Factors for Timing Delays (normalized to
TJ = 70°C, VCC = 1.425 V) and Table 2-7 • Temperature and Voltage Derating Factors
for Timing Delays (normalized to TJ = 70°C, VCC = 1.14 V) were updated. Table 2-8 •
Power Supply State per Mode is new.
2-6,
2-7
The tables in the "Quiescent Supply Current" section were updated (SAR 24882 and
SAR 24112).
2-7
VJTAG was removed from Table 2-10 • Quiescent Supply Current (IDD) Characteristics,
IGLOO nano Sleep Mode* (SARs 24112, 24882, and 79503).
2-8
The note stating what was included in IDD was removed from Table 2-11 • Quiescent
Supply Current (IDD) Characteristics, IGLOO nano Shutdown Mode. The note, "per
VCCI or VJTAG bank" was removed from Table 2-12 • Quiescent Supply Current (IDD),
No IGLOO nano Flash*Freeze Mode1. The note giving IDD was changed to "IDD =
NBANKS * ICCI + ICCA."
2-8
The values in Table 2-13 • Summary of I/O Input Buffer Power (per pin) – Default I/O
Software Settings and Table 2-14 • Summary of I/O Output Buffer Power (per pin) –
Default I/O Software Settings1 were updated. Wide range support information was
added.
2-9
R ev i si o n 1 7
5 -3
Datasheet Information
Revision
Revision 10
(continued)
Changes
Page
The following tables were updated with current available information. The equivalent 2-19
through
software default drive strength option was added.
2-40
Table 2-21 • Summary of Maximum and Minimum DC Input and Output Levels
Table 2-25 • Summary of I/O Timing Characteristics—Software Default Settings
Table 2-26 • Summary of I/O Timing Characteristics—Software Default Settings
Table 2-28 • I/O Output Buffer Maximum Resistances 1
Table 2-29 • I/O Weak Pull-Up/Pull-Down Resistances
Table 2-30 • I/O Short Currents IOSH/IOSL
Timing tables in the "Single-Ended I/O Characteristics" section, including new tables for
3.3 V and 1.2 V LVCMOS wide range.
Table 2-40 • Minimum and Maximum DC Input and Output Levels for LVCMOS 3.3 V
Wide Range
Table 2-63 • Minimum and Maximum DC Input and Output Levels
Table 2-67 • Minimum and Maximum DC Input and Output Levels (new)
The formulas in the notes to Table 2-29 • I/O Weak Pull-Up/Pull-Down Resistances were
revised (SAR 21348).
2-24
The text introducing Table 2-31 • Duration of Short Circuit Event before Failure was
revised to state six months at 100° instead of three months at 110° for reliability
concerns. The row for 110° was removed from the table.
2-25
The following sentence was deleted from the "2.5 V LVCMOS" section (SAR 24916): "It
uses a 5-V tolerant input buffer and push-pull output buffer."
2-32
The FDDRIMAX and FDDOMAX values were added to tables in the "DDR Module
Specifications" section (SAR 23919). A note was added stating that DDR is not
supported for AGLN010, AGLN015, and AGLN020.
2-51
Tables in the "Global Tree Timing Characteristics" section were updated with new
information available.
2-64
Table 2-100 • IGLOO nano CCC/PLL Specification and Table 2-101 • IGLOO nano
CCC/PLL Specification were revised (SAR 79390).
2-70,
2-71
Tables in the SRAM "Timing Characteristics" section and FIFO "Timing Characteristics"
section were updated with new information available.
2-77,
2-85
Table 3-3 • TRST and TCK Pull-Down Recommendations is new.
3-4
A note was added to the "CS81" pin tables for AGLN060, AGLN060Z, AGLN125,
4-9,
AGLN125Z, AGLN250, and AGLN250Z indicating that pins F1 and F2 must be grounded through
(SAR 25007).
4-14
5- 4
A note was added to the "CS81" and "VQ100" pin tables for AGLN060 and AGLN060Z
stating that bus hold is not available for pin H7 or pin 45 (SAR 24079).
4-9,
4-24
The AGLN250 function for pin C8 in the "CS81" table was revised (SAR 22134).
4-13
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
Revision / Version
Changes
Revision 9 (Mar2010)
All product tables and pin tables were updated to show clearly that AGLN030 is
Product Brief Advance available only in the Z feature grade at this time. The nano-Z feature grade
devices are designated with a Z at the end of the part number.
v0.9
Page
N/A
Packaging Advance
v0.8
Revision 8 (Jan 2009)
The "Reprogrammable Flash Technology" section was revised to add "250 MHz
(1.5 V systems) and 160 MHz (1.2 V systems) System Performance."
I
Product Brief Advance The note for AGLN030 in the "IGLOO nano Devices" table and "I/Os Per
v0.8
Package" table was revised to remove the statement regarding package
compatibility with lower density nano devices.
II, II
The "I/Os with Advanced I/O Standards" section was revised to add definitions for
hot-swap and cold-sparing.
1-8
Packaging Advance
v0.7
The "UC81", "CS81", "QN48", and "QN68" pin tables for AGLN030 are new.
The "CS81"pin table for AGLN060 is new.
4-5, 4-8,
4-17, 4-21
4-9
The "CS81" and "VQ100" pin tables for AGLN060Z are new.
4-10, 4-25
The "CS8" and "VQ100" pin tables for AGLN125Z are new.
4-12, 4-27
The "CS81" and "VQ100" pin tables for AGLN250Z is new.
4-14, 4-29
The –F speed grade is no longer offered for IGLOO nano devices and was
Product Brief Advance removed from the datasheet.
v0.7
Revision 7 (Apr 2009)
N/A
DC and Switching
Characteristics
Advance v0.3
Revision 6 (Mar 2009)
The "VQ100" pin table for AGLN030 is new.
4-23
The "100-Pin QFN" section was removed.
N/A
The QN100 package was removed for all devices.
N/A
Packaging Advance
v0.6
Revision 5 (Feb 2009)
Packaging Advance
v0.5
Revision 4 (Feb 2009)
Product Brief Advance "IGLOO nano Devices" table was updated to change the maximum user I/Os for
v0.6
AGLN030 from 81 to 77.
The "Device Marking" section is new.
Revision 3 (Feb 2009)
II
III
The following table note was removed from "IGLOO nano Devices" table: "Six
Product Brief Advance chip (main) and three quadrant global networks are available for AGLN060 and
above."
v0.5
II
The CS81 package was added for AGLN250 in the "IGLOO nano Products
Available in the Z Feature Grade" table.
IV
Packaging Advance
v0.4
The "UC81" and "CS81" pin tables for AGLN020 are new.
The "CS81" pin table for AGLN250 is new.
R ev i si o n 1 7
4-4, 4-7
4-13
5 -5
Datasheet Information
Revision / Version
Changes
Revision 2 (Dec 2008)
Page
The second table note in "IGLOO nano Devices" table was revised to state,
Product Brief Advance "AGLN060, AGLN125, and AGLN250 in the CS81 package do not support PLLs.
AGLN030 and smaller devices do not support this feature."
v0.4
II
The I/Os per package for CS81 were revised to 60 for AGLN060, AGLN125, and
AGLN250 in the "I/Os Per Package"table.
II
Packaging Advance
v0.3
The "UC36" pin table is new.
4-2
Revision 1 (Nov 2008)
The "Advanced I/Os" section was updated to include wide power supply voltage
Product Brief Advance support for 1.14 V to 1.575 V.
v0.3
I
The AGLN030 device was added to product tables and replaces AGL030 entries
that were formerly in the tables.
IV
The "I/Os Per Package"table was updated for the CS81 package to change the
number of I/Os for AGLN060, AGLN125, and AGLN250 from 66 to 64.
II
The "Wide Range I/O Support" section is new.
1-8
The table notes and references were revised in Table 2-2 • Recommended
Operating Conditions 1. VMV was included with VCCI and a table note was added
stating, "VMV pins must be connected to the corresponding VCCI pins. See Pin
Descriptions for further information." Please review carefully.
2-2
VJTAG was added to the list in the table note for Table 2-9 • Quiescent Supply
Current (IDD) Characteristics, IGLOO nano Flash*Freeze Mode*. Values were
added for AGLN010, AGLN015, and AGLN030 for 1.5 V.
2-7
VCCI was removed from the list in the table note for Table 2-10 • Quiescent
Supply Current (IDD) Characteristics, IGLOO nano Sleep Mode*.
2-8
Values for ICCA current were updated for AGLN010, AGLN015, and AGLN030 in
Table 2-12 • Quiescent Supply Current (IDD), No IGLOO nano Flash*Freeze
Mode1.
2-8
Values for PAC1 and PAC2 were added to Table 2-15 • Different Components 2-10, 2-11
Contributing to Dynamic Power Consumption in IGLOO nano Devices and Table
2-17 • Different Components Contributing to Dynamic Power Consumption in
IGLOO nano Devices.
Table notes regarding wide range support were added to Table 2-21 • Summary of
Maximum and Minimum DC Input and Output Levels.
2-19
1.2 V LVCMOS wide range values were added to Table 2-22 • Summary of 2-19, 2-20
Maximum and Minimum DC Input Levels and Table 2-23 • Summary of AC
Measuring Points.
The following table note was added to Table 2-25 • Summary of I/O Timing
Characteristics—Software Default Settings and Table 2-26 • Summary of I/O
Timing Characteristics—Software Default Settings: "All LVCMOS 3.3 V software
macros support LVCMOS 3.3 V wide range, as specified in the JESD8-B
specification."
2-21
3.3 V LVCMOS Wide Range and 1.2 V Wide Range were added to Table 2-28 • 2-23, 2-24
I/O Output Buffer Maximum Resistances 1 andTable 2-30 • I/O Short Currents
IOSH/IOSL.
5- 6
R ev isio n 1 7
IGLOO nano Low Power Flash FPGAs
Revision / Version
Changes
Page
Revision 1 (cont’d)
The "QN48" pin diagram was revised.
4-16
Packaging Advance
v0.2
Note 2 for the "QN48", "QN68", and "100-Pin QFN" pin diagrams was changed to 4-16, 4-19
"The die attach paddle of the package is tied to ground (GND)."
The "VQ100" pin diagram was revised to move the pin IDs to the upper left corner
instead of the upper right corner.
4-23
The following tables and sections were updated to add the UC81 and CS81
Product Brief Advance packages for AGL030:
v0.2
"IGLOO nano Devices"
"I/Os Per Package"
"IGLOO nano Products Available in the Z Feature Grade"
"Temperature Grade Offerings"
N/A
Revision 0 (Oct 2008)
The "I/Os Per Package" table was updated to add the following information to
table note 4: "For nano devices, the VQ100 package is offered in both leaded and
RoHS-compliant versions. All other packages are RoHS-compliant only."
II
The "IGLOO nano Products Available in the Z Feature Grade" section was
updated to remove QN100 for AGLN250.
IV
1-4
The device architecture figures, Figure 1-3 • IGLOO Device Architecture Overview
with Two I/O Banks (AGLN060, AGLN125) through Figure 1-4 • IGLOO Device through
1-5
Architecture Overview with Four I/O Banks (AGLN250), were revised. Figure 1-1 •
IGLOO Device Architecture Overview with Two I/O Banks and No RAM
(AGLN010 and AGLN030) is new.
The "PLL and CCC" section was revised to include information about CCC-GLs in
AGLN020 and smaller devices.
1-7
The "I/Os with Advanced I/O Standards" section was revised to add information
about IGLOO nano devices supporting double-data-rate applications.
1-8
R ev i si o n 1 7
5 -7
Datasheet Information
Datasheet Categories
Categories
In order to provide the latest information to designers, some datasheet parameters are published before
data has been fully characterized from silicon devices. The data provided for a given device, as
highlighted in the "IGLOO nano Device Status" table on page II, is designated as either "Product Brief,"
"Advance," "Preliminary," or "Production." The definitions of these categories are as follows:
Product Brief
The product brief is a summarized version of a datasheet (advance or production) and contains general
product information. This document gives an overview of specific device and family information.
Advance
This version contains initial estimated information based on simulation, other products, devices, or speed
grades. This information can be used as estimates, but not for production. This label only applies to the
DC and Switching Characteristics chapter of the datasheet and will only be used when the data has not
been fully characterized.
Preliminary
The datasheet contains information based on simulation and/or initial characterization. The information is
believed to be correct, but changes are possible.
Unmarked (production)
This version contains information that is considered to be final.
Export Administration Regulations (EAR)
The products described in this document are subject to the Export Administration Regulations (EAR).
They could require an approved export license prior to export from the United States. An export includes
release of product or disclosure of technology to a foreign national inside or outside the United States.
Safety Critical, Life Support, and High-Reliability Applications
Policy
The Microsemi products described in this advance status document may not have completed
Microsemi’s qualification process. Microsemi may amend or enhance products during the product
introduction and qualification process, resulting in changes in device functionality or performance. It is
the responsibility of each customer to ensure the fitness of any Microsemi product (but especially a new
product) for a particular purpose, including appropriateness for safety-critical, life-support, and other
high-reliability applications. Consult Microsemi’s Terms and Conditions for specific liability exclusions
relating to life-support applications. A reliability report covering all of the Microsemi SoC Products
Group’s products is at http://www.microsemi.com/socdocuments/ORT_Report.pdf. Microsemi also offers
a variety of enhanced qualification and lot acceptance screening procedures. Contact your local
Microsemi sales office for additional reliability information.
5- 8
R ev isio n 1 7
Microsemi Corporation (NASDAQ: MSCC) offers a comprehensive portfolio of semiconductor
solutions for: aerospace, defense and security; enterprise and communications; and industrial
and alternative energy markets. Products include high-performance, high-reliability analog and
RF devices, mixed signal and RF integrated circuits, customizable SoCs, FPGAs, and
complete subsystems. Microsemi is headquartered in Aliso Viejo, Calif. Learn more at
www.microsemi.com.
Microsemi Corporate Headquarters
One Enterprise, Aliso Viejo CA 92656 USA
Within the USA: +1 (949) 380-6100
Sales: +1 (949) 380-6136
Fax: +1 (949) 215-4996
© 2013 Microsemi Corporation. All rights reserved. Microsemi and the Microsemi logo are trademarks of
Microsemi Corporation. All other trademarks and service marks are the property of their respective owners.
51700110-17/6.13
Similar pages