F1T1G - F1T7G 1.0 AMP. Glass Passivated Fast Recovery Rectifiers TS-1 Features Glass passivated chip junction. High efficiency, Low VF High current capability High reliability High surge current capability Low power loss Mechanical Data Cases: Molded plastic Epoxy: UL 94V-0 rate flame retardant Lead: Pure tin plated, Lead free., solderable per MIL-STD-202, Method 208 guaranteed Polarity: Color band denotes cathode end High temperature soldering guaranteed: 260 oC /10 seconds/.375”,(9.5mm) lead lengths at 5 lbs.,(2.3kg) tension Mounting position: Any Weight: 0.20 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length o @T A = 55 C Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current @ T A =25 o C o at Rated DC Blocking Voltage @ T A =125 C Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance (Note 3) Operating Temperature Range T J Symbol F1T 1G V RRM 50 V RMS 35 V DC 50 F1T 2G 100 70 100 F1T 3G 200 140 200 F1T 4G 400 280 400 F1T 5G 600 420 600 F1T 6G 800 560 800 F1T Units 7G 1000 V 700 V 1000 V I(AV) 1.0 A IFSM 30 A VF 1.3 V IR 5.0 150 uA uA nS pF o C/W Trr Cj R θJA TJ 150 250 15 90 -65 to +150 -65 to +150 Storage Temperature Range T STG T STG 1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A Notes: 2. Measured at 1 MHz and Applied Reverse Voltage of 4. 0 Volts D.C. 3. Mount on Cu-Pad Size 5mm x 5mm on P.C.B. 500 o o C C Version: A06 RATINGS AND CHARACTERISTIC CURVES (F1T1G THRU F1T7G) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- TYPICAL REVERSE CHARACTERISTICS PER LEG 1000 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375" (9.5mm) Lead Length 1.25 1.00 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) 1.50 0.75 0.50 0.25 0 0 25 50 75 100 125 150 175 o AMBIENT TEMPERATURE. ( C) 100 Tj=125 0C 10 Tj=75 0C 1.0 Tj=25 0C FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 0.1 0 40 40 60 80 100 120 140 30 Tj=25 0C 20 FIG.5- TYPICAL FORWARD CHARACTERISTICS 10 10 8.3ms Single Half Sine Wave JEDEC Method 0 1 2 4 6 8 10 20 NUMBER OF CYCLES AT 60Hz 40 60 80 100 FIG.4- TYPICAL JUNCTION CAPACITANCE 100 JUNCTION CAPACITANCE.(pF) 20 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) INSTANTANEOUS FORWARD CURRENT. (A) PEAK FORWARD SURGE CURRENT. (A) 50 Tj=25 0C 10 1 0.1 Tj=25oC Pulse Width=300 s 1% Duty Cycle 1 1 10 .01 100 .4 .6 REVERSE VOLTAGE. (V) .8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 0 -0.25A (+) -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06