Bel BPEU2000 Ac/dc converter Datasheet

The BPEU Series of AC/DC Converters is
available with multiple outputs and output
power from 1300 W up to 3000 W. All
models incorporate active Power Factor
Correction (PFC).
Other standard features include current
and voltage monitoring, overvoltage,
overtemperature as well as short circuit
protection.
These power supplies were designed to
power radio-frequency power amplifier
(RFPA) applications in the Broadcasting
industry.

Output Power 2000 W

Single-Phase 230 VAC Input

Power Factor > 0.99

Total Harmonic Distortion < 5%

Main Output: +40 V to +50 V
(+20 V to +50 V by remote control)

Auxiliary Output: +12 V/500 mA

Current and Voltage Monitoring

Remote Enable
North America
+1-866.513.2839
Asia-Pacific
+86.755.29885888
Europe, Middle East
+353 61 225 977
Bel Power Solutions
152 North 3rd Street, Suite 805
San Jose, CA 95112 USA
[email protected]
© 2015 Bel Power Solutions, inc.
D-2000-ST02_001
BPEU2000
PARAMETER
DESCRIPTION / CONDITION
Voltage
184 – 264 VAC Single-Phase
Frequency
47…63 Hz
Efficiency
> 90% @ full-load @ 230 VAC
Inrush Current
≤ 30 Apk @ 230 VAC
Power Factor
0,99 @ full-load @ 230 VAC
THD
≤ 5% @ Pout ≥ 1 kW
OUTPUT
VOLTAGE SETTING BY
TRIM (VDC)
V1
+40 to +50 *
V2
*
VOLTAGE SETTING BY
EXT. 0 ÷ 5VDC (VDC)
+20 to +50 **
12
N/A
Inom
(A)
Imax
(A)
TOLERANCE
%
RIPPLE
%
POWER (W)
40
45
<2
≤2
2000
0.5
1
≤5
<5
6
V1 adjustable manually by multi-turns trimmer set on board (see page 2 "+48 Vadj")
** See "VOLTAGE OUTPUT ADJUSTEMENT PROCEDURE" section at page 2
PARAMETER
DESCRIPTION / CONDITION
Over-load V1:
Constant current limiting (see curve)
Short-circuit V1:
hiccup mode (with auto recovery)
Over-voltage V1:
set point = 56V ± 5%, not automatic return to operation
Over-temperature:
automatic return to operation with hysteresis
General:
AC side thermal fuses (T)
PARAMETER
DESCRIPTION / CONDITION
Output V1 Current monitor IM
Linear analogic signal 100 mV → 1A (Internal impedance 3 kΩ)
Output V1 Voltage monitor VM
Linear analogic signal 1 / 10 Vout (Internal impedance 2 kΩ)
High temperature alarm OTA
Open-Collector, max. sink 4 mA; alarm = low (on = 70°C; reset = 60°C tolerance ± 5%)
Over temperature alarm OTP
Open-Collector, max. sink 4 mA; alarm = low (on = 80°C; reset = 70°C tolerance ± 5%)
Under voltage input alarm PWR FAIL
Open-Collector, max. sink 4 mA; alarm = low (set point Vin < 180 VAC)
Output V1 Remote ENABLE
Connected to COM = power-on, not connected = power-off (minimum current sink 5 mA)
PARAMETER
DESCRIPTION / CONDITION
Operating Temperature:
-10 to +50°C @ full-load (forced air-cooling, see Thermal Protection)
Storage Temperature:
-20 to +85°C
866.513.2839
[email protected]
© 2015 Bel Power Solutions, inc.
D-2000-ST02_001
BPEU2000
PARAMETER
DESCRIPTION / CONDITION
Safety:
EN60950-1:2006+A11:2009 / EN60065:2002+A1:2006
EMC:
EN61000-6-4:2007
Harmonics Current:
EN61000-3-2 (class A)
CE Mark
PARAMETER
DESCRIPTION / CONDITION
Input
3 pole screw type terminal block 24 A, 2.5 mm2
Output V1
2 pole screw type terminal block 57 A, 16 mm2
Signals / Controls / Output V2
Male FLAT type connector 10 pole DIL
Figure 1 - Connections
VOLTAGE OUTPUT ADJUSTMENT PROCEDURE V1
Set the Jumper on pin 1 - 2 to adjust Vout by on board trimmer "+48 Vadj"
Set the Jumper on pin 2 - 3 to reduce linearly Vout set by trimmer by a 0 - 5 VDC external signal:
0 VDC → output V1 = voltage set by trimmer "+48 Vadj"
5 VDC → output V1 = voltage set by trimmer "+48 Vadj" -20 VDC
866.513.2839
[email protected]
© 2015 Bel Power Solutions, inc.
D-2000-ST02_001
BPEU2000
PARAMETER
Material
Fixing
Dimensions (W x H x D)
DESCRIPTION / CONDITION
Case:
Aluzinc 10/10 mm
Cover:
Aluzinc 10/10 mm
N° 4 hole Ø 5 mm (see Dimensions)
128 x 72 x 350 mm
Notes: Tolerances 0.5 mm max
Figure 2 - Mechanical Drawing
Figure 3 – Cooling Method
866.513.2839
[email protected]
© 2015 Bel Power Solutions, inc.
D-2000-ST02_001
BPEU2000
Figure 4 – Output Characteristics
Figure 5 – Voltage Output Adjustments
Vout
Vout
50
50
trimmer setting
45
40
40
35
30
30
20
25
20
10
15
0
10
0
5
10
15
20
25
30
35
40
45
50 Iout
0
1
Figure 6 – Efficiency
2
3
4
5
Vprog.
Figure 7 – Power Factor
η%
P.F.
92
1
90
88
0,98
86
84
82
0,96
80
78
0,94
76
74
72
0,92
70
68
0,9
66
0
300
600
900
1200
1500
1800
2100 Pout
0
300
600
900
1200
1500
1800
2100 Pout
Figure 8 – Conducted Noise
NUCLEAR AND MEDICAL APPLICATIONS - Products are not designed or intended for use as critical components in life support systems, equipment used in
hazardous environments, or nuclear control systems.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date
manufactured. Specifications are subject to change without notice.
866.513.2839
[email protected]
© 2015 Bel Power Solutions, inc.
D-2000-ST02_001
Similar pages