Document 483 Flyback Transformer For Texas Instruments TPS23750 PoE Powered Device Controller • Isolated non-synchronous flyback transformers developed for Texas Instruments PMP717 reference design. • Designed for discontinuous conduction mode, 34 – 57 V input • 1500 Vrms isolation primary to secondary windings Core material Ferrite Terminations RoHS tin-silver (96.5/3.5) over tin over nickel over phos bronze. Other terminations available at additional cost. Weight 1.4 g Ambient temperature –40°C to +125°C Storage temperature Component: –40°C to +125°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 500 per 13″ reel Plastic tape: 24 mm wide, 0.36 mm thick, 16 mm pocket spacing, 6.13 mm pocket depth PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf Inductance Part at 0 Adc2 number1 ±10% (µH) Inductance Leakage Turns ratio at Ipk3 DCR max Inductance4 min (µH) (Ohms) max (µH) pri : sec5 pri : bias C1453-AL_ 50 40 0.185 (pins 3 – 1) 0.030 (pins 6 – 10) 0.030 (pins 7 – 9) 0.385 (pins 4 – 5) 1.10 1 : 0.166 1. When ordering, please specify packaging code: Dot indicates pin 1 1 10 0.453 max 11,50 1.22 3.3 V, 1.5A 7 6 Pri Sec 10 9 1 4 6 5 Output6 3 C1453-AL XXXX Y C1453-ALD Packaging: D = 13″ machine ready reel. EIA-481 embossed plastic tape (500 per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance is for the primary, measured at 250 kHz, 0.3 Vrms. 3. Peak primary current drawn at minimum input voltage. 4. Leakage inductance is for the primary winding with the secondary windings shorted. 5. Turns ratio is with the secondary windings connected in parallel. 6. Output of the secondary is with the windings connected in parallel. Bias winding output is 10 V. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 1 : 0.5 Ipk3 (A) 0.512 max 13,00 Bias 5 Secondary windings to be connected in parallel on the PC board. 0.256 max 6,50 0.004 / 0,10 5 6 1 10 0.028 0,70 0.063 1,60 0.079 2,00 0.394 10,00 1 10 0.079 2,00 inches Dimensions are in mm US +1-847-639-6400 [email protected] UK +44-1236-730595 [email protected] Taiwan +886-2-2264 3646 [email protected] China +86-21-6218 8074 [email protected] Singapore + 65-6484 8412 [email protected] 0.055 1,40 Document 483 Recommended Land Pattern Revised 12/21/11 © Coilcraft Inc. 2013 This product may not be used in medical or high risk applications without prior Coilcraft approval. Specification subject to change without notice. Please check web site for latest information.