Key-type Selector Switch (Detachable) (Cylindrical 16-dia.) A165K CSM_A165K_DS_E_3_1 Separate Construction with Cylindrical 16-dia. Body • Short mounting depth, less than 28.5 mm below panel • Wide range of switching capacity from standard to microload • Oil-resistant IP65 models Refer to Safety Precautions for All Pushbutton Switches and Safety Precautions on page 11. List of Models Rectangular Solder terminals Screwless clamp connector Model Square Round A165K-J Series A165K-A Series A165K-T Series A165K-J Series A165K-A Series A165K-T Series 1 A165K Model Number Structure Model Number Legend ..... The model numbers used to order sets of Units are illustrated below. One set comprises the Selector, Switch, and 2 Keys. For information on combinations, refer to Ordering Information on page 3. (1) (2) (3) A165K- J 3ML - 2 (1) Shape of Selector Symbol Shape Color J Rectangular A Square Black T Round (2) Number of Notches/Resetting Method Symbol 2ML 2MR 2M 2AL 3MC 3MR 3ML No. of notches 2 notches Reset method Manual Automatic 3 notches Manual 3M 3AC 3 notches Automatic Key release position Left Right Left and right Left Center Right Left Left, right, and center Center (3) Contact Configuration Symbol 1 2 2S Type SPDT DPDT DPDT Terminal Solder Terminal Screw-less Clamp Note: Only DPDT contacts are available with 3-notch models. 2 A165K Ordering Information Ordering as a Set .................The model numbers used to order sets of Units are given in the following tables. One set comprises the Selector, Switch and 2 Keys. Solder Terminals Rectangular Models Oil-resistant IP65 Number of notches Output SPDT A165K-J Reset method Left Right Left and right Left Left Right Left and right Left Center Right Left Left, right, and center Manual Automatic 2 notches DPDT Manual Automatic 3 notches DPDT Key release position Manual Model A165K-J2ML-1 A165K-J2MR-1 A165K-J2M-1 A165K-J2AL-1 A165K-J2ML-2 A165K-J2MR-2 A165K-J2M-2 A165K-J2AL-2 A165K-J3MC-2 A165K-J3MR-2 A165K-J3ML-2 A165K-J3M-2 Square Models A165K-A Oil-resistant IP65 Number of notches Output SPDT Reset method Left Right Left and right Left Left Right Left and right Left Center Right Left Left, right, and center Manual Automatic 2 notches DPDT Manual Automatic 3 notches DPDT Key release position Manual Model A165K-A2ML-1 A165K-A2MR-1 A165K-A2M-1 A165K-A2AL-1 A165K-A2ML-2 A165K-A2MR-2 A165K-A2M-2 A165K-A2AL-2 A165K-A3MC-2 A165K-A3MR-2 A165K-A3ML-2 A165K-A3M-2 Round Models A165K-T Oil-resistant IP65 Number of notches Output SPDT Reset method Manual Automatic 2 notches DPDT Manual Automatic 3 notches DPDT Manual Key release position Left Right Left and right Left Left Right Left and right Left Center Right Left Left, right, and center Model A165K-T2ML-1 A165K-T2MR-1 A165K-T2M-1 A165K-T2AL-1 A165K-T2ML-2 A165K-T2MR-2 A165K-T2M-2 A165K-T2AL-2 A165K-T3MC-2 A165K-T3MR-2 A165K-T3ML-2 A165K-T3M-2 3 A165K Ordering Information Ordering Individually ......... Selectors and Switches can be ordered separately. Combinations that are not available as sets can be created using individual Units. Also, store the parts as spares for maintenance and repairs. Operation Units (Listed on Page 5.) Rectangular (A165K-J) Square (A165K-A) Round (A165K-T) (Standard condition when shipped) Switches with 2 Notches FP ·Two keys are provided. (75°) 90° Switches with 3 Notches (45°) 45° FP (45°) 45° Note: The figures in parentheses are for self-resetting models. FP: Free position Socket Units (Listed on Page 5.) Solder terminals PCB terminals Screw-less clamp connector 4 A165K Ordering Information Ordering Individually .........Selectors and Switches can be ordered separately. Combinations that are not available as sets can be created using individual Units. Also, store the parts as spares for maintenance and repairs. Selectors Appearance Rectangular (A165K-J) Number of notches 2 notches Reset method Key release position Model A165K-J2ML A165K-J2MR A165K-J2M A165K-J2AL A165K-J3MC A165K-J3MR A165K-J3ML A165K-J3M A165K-J3AC A165K-A2ML A165K-A2MR A165K-A2M A165K-A2AL A165K-A3MC A165K-A3MR A165K-A3ML A165K-A3M A165K-A3AC A165K-T2ML A165K-T2MR A165K-T2M A165K-T2AL A165K-T3MC A165K-T3MR A165K-T3ML A165K-T3M A165K-T3AC Manual Automatic 3 notches Manual Automatic Square (A165K-A) 2 notches Manual Automatic 3 notches Manual Automatic Round (A165K-T) 2 notches Manual Automatic 3 notches Manual Automatic Switches Appearance Classification Model SPDT A16S-2N-1 2 notches DPDT Switch 3 notches Solder terminal DPDT A16S-3N-2 SPDT 2 notches A16S-2N-2 A16S-2N-1P PCB terminal DPDT A16S-2N-2P Switches with Screw-less Clamp Appearance Classification Model 2 notches Common to standard load and microload. DPDT A16-2S Remarks Common to ones for pushbutton switches. Non-lighted 3 notches A16S-3N-2LS --- 5 A165K Ordering Information Accessories and Tools (Order Separately) Accessories Name Appearance Classification Panel Plugs Model Rectangular A16ZJ-3003 Square A16ZA-3003 Round A16ZT-3003 Remarks Used for covering the panel cutouts for future panel expansion. Degree of protection: IP40 Color: Black Tools Name Appearance Screw Fitting Extractor Model A16Z-3004 A16Z-5080 Pushbutton Switch Knob-type Selector Switch Yes Yes Yes Yes Applicable types Key-type Emergency Selector Stop Switch Switch Yes Yes Yes Yes Remarks Indicator Yes Convenient for ganged installation. Yes Convenient for extracting the Lamp from a Solder-terminal Socket Unit. Key Appearance Model A165K-KEY Note: Two Keys are provided. Ordering as a Set: Refer to page 3. ■ Specifications, and dimensions: Refer to page 7 to 10. ■ Accessories, replacements, and tools: Refer to this page. 6 A165K Specifications Approved Standard Ratings UL, cUL (File No. E41515) TÜV (EN60947-5-1) (Low Voltage Directive) CCC (GB14048.5) 5 A at 125 VAC, 3 A at 250 VAC (general use) 3 A at 30 VDC (resistive) 3 A at 250 VAC 3 A at 30 VDC 5 A at 125 VAC 3 A at 250 VAC 3 A at 30 VDC Note: Certification has been obtained for the Switch Unit. For detailed information on individual products that have received certification, consult your supplier. Ratings Contacts Contact Form Rated voltage Resistive load 125 VAC 5A 250 VAC 3A 30 VDC 3A Name Contact form NC SPDT COM NO Minimum applicable load: 1 mA at 5 VDC Rated values are obtained from tests conducted under the following conditions. 1. Load: Resistive load 2. Mounting conditions: No vibration and no shock 3. Temperature: 20±2°C 4. Operating frequency: 20 times/min Characteristics Operating Characteristics Socket Units Type Item Type Allowable operating frequency Key-type Selector Switch Characteristics Mechanical 20 operations/minute max. Operating force (OF) max. Electrical 10 operations/minute max. Set position (SP) 100 MΩ min. (at 500 VDC) Operation Angle Insulation resistance Between terminals of same polarity Dielectric strength 1,000 VAC, 50/60 Hz for 1 minute Between terminals of different polarity Between each terminal and ground Vibration resistance Shock resistance Durability (45°) 45° 90° 45° +100 Three notches (75°) FP 3 notches 0.1 N·m 90±5° Two notches 2,000 VAC, 50/60 Hz for 1 minute Key-type Selector Switch 2 notches FP (45°) 45° 2,000 VAC, 50/60 Hz for 1 minute 10 to 55 Hz, 1.5-mm double amplitude (malfunction within 1 ms) Malfunction Destruction 500 m/s2 Malfunction 150 m/s2 max. (malfunction within 1 ms) Mechanical 250,000 operations min. (durability of key: 10,000 operations min.) Electrical Contact Configuration 100,000 operations min. Electric shock protection class Note: The angle used for automatic reset is shown in parentheses. FP: Free position Contact configuration Class II PTI (tracking characteristic) Degree of contamination No. of notches 175 3 (IEC60947-5-1) Approx. 26.5 g (in the case of a DPDT switch key) Weight −10°C to 55°C (with no icing or condensation) Ambient operating temperature Ambient operating humidity 35% to 85%RH −25°C to 65°C (with no icing or condensation) Ambient storage temperature SPDT Position SW DPDT Position SW1 SW2 2 notches 3 notches --- Screw-less Clamp Item Type Recommended wire size Usable wires and tensile strength Twisted wire Solid wire Tensile strength SW1 Screw-less Clamp SW2 0.5 mm2 twisted wire or 0.8 mm-dia. solid wire 0.3 mm2 0.5 mm2 0.75 mm2 0.5 mm dia. 0.8 mm dia. 1.0 mm dia. 10 N 20 N 30 N 1.25 mm2 --40 N Length of exposed wire 10 ±1 mm Compliant standards JIS C 2811 Terminal Blocks for Industrial Use 7 A165K Nomenclature Model Structure Selector ●Key ●Flange Shape Rectangular (A165K-J) ●Number of Notches and Reset Method · 2 Notches: Manual, Automatic · 3 Notches: Manual, Automatic Square (A165K-A) Round (A165K-T) ●Protective Structure Oil-resistant IP65 Switch ●Switch Specifications 5 A at 125 VAC 5 A at 250 VAC 3 A at 130 VDC Minimum applicable load 1 mA at 25 VDC ●Terminal Type Solder terminals PCB terminals The flange can be rotated to easily change the operation angle of the knob. For information on rotating the flange, refer to the A165S/W datasheet. Example: Knob-type Selector Switch with Two Notches FP (75°) 90° 90° 90° (Standard condition when shipped) Note: The angle is 75° for self-resetting models. 8 A165K Dimensions (Unit: mm) The Dimension shows 2-switch outputs. Rectangular A165K-J Solder terminals (tab terminals #110) M16×1 1.5 12.2 18 4 10.8 9.5 21.1 28.5 34.5 ±1 2.8 20 12.4 15.8 18 24 Model, standard, lot No., serial number Mounting nut Packing (t0.5) Lock ring * Refer to the A165S/W for Panel cutouts. Square A165K-A Solder terminals (tab terminals #110) M16×1 1.5 12.2 18 4 10.8 9.5 21.1 28.5 34.5 ±1 2.8 20 12.4 15.8 18 18 Model, standard, lot No., serial number Mounting nut Packing (t0.5) Lock ring * Refer to the A165S/W for Panel cutouts. Round A165K-T Solder terminals (tab terminals #110) M16×1 1.5 12.2 18 4 10.8 9.5 34.5 ±1 21.1 28.5 2.8 20 12.4 15.8 18 18 Model, standard, lot No., serial number Packing (t0.5) Mounting nut Lock ring * Refer to the A165S/W for Panel cutouts. 9 A165K Dimensions • The Dimension shows 2-switch outputs. • The lamp terminal is also provided with non-lighted models. Rectangular A165K@-2S Screw-Less Clamp 9.5 • A rectangular model is listed as an example. Panel Cutouts 48.9 10.8 4 (Unit: mm) 2 16 +0.2 0 dia. 24 25 min. 23.9 M16×1 33 min. Switch dismounting lever Lock ring Mounting nut (31.7) 27.4 18 24 23.5 Packing (t0.5) Recommended panel thickness: 0.5 to 3.2 mm Terminal Arrangement For information on the terminal arrangement, refer to the A165S/W datasheet. Panel Mounting and Socket Unit Mounting and Removal Refer to the A16 Pushbutton Switch datasheet. Flange Rotation Refer to the A165S/W datasheet. 10 A165K Safety Precautions Refer to Safety Precautions for All Pushbutton Switches. WARNING Always turn OFF the power and wait for 10 minutes before replacing the incandescent lamp. If the lamp is replaced immediately after the power is turned OFF, the remaining heat may cause burns. Precautions for Correct Use Mounting • Always make sure that the power is turned OFF before mounting, removing, or wiring the Switch, or performing maintenance. • Do not tighten the mounting nut more than necessary using tools such as pointed-nose pliers. Doing so will damage the mounting nut. The tightening torque is 0.29 to 0.49 N·m. Wiring • Solder terminals and quick-connect terminals (#110) are commonly used for terminals. • Be sure to use electrical wires that are a size appropriate for the applied voltage and carry current (conductor size is 0.5 to 0.75 mm2). Perform soldering according to the conditions provided below. If the soldering is not properly performed, the lead wires will become detached, resulting in short-circuits. 1. Hand soldering: 350°C, within 3 s 2. Dip soldering: 350°C, within 3 s Wait for one minute after soldering before exerting any external force on the solder. • Use non-corrosive resin fluid as the flux. • Make sure that the electric cord is wired so that it does not touch the Unit. If the electric cord touches the Unit, then electric wires with a heat resistance of 100°C min. must be used. • After wiring the Switch, maintain an appropriate clearance and creepage distance. Using the Microload • Insert a contact protection circuit, if necessary, to prevent the reduction of life expectancy due to extreme wear on the contacts caused by loads where inrush current occurs when the contact is opened and closed. • The A16 allows both a standard load (125 V at 5A, 250 V at 3 A) and a microload. If a standard load is applied, however, the microload area cannot be used. If the microload area is used with a standard load, the contact surface will become rough, and the opening and closing of the contact for a microload may become unreliable. • The minimum applicable load is the N-level reference value. This value indicates the malfunction reference level for the reliability level of 60% (λ 60) (conforming to JIS C5003). The equation, λ 60 = 0.5 × 10-4/operations indicates that the estimated malfunction rate is less than 1/2,000,000 operations with a reliability level of 60%. Voltage (V) Do not apply a voltage between the incandescent lamp and the terminal that is greater than the rated voltage. If the incandescent lamp is broken, the operating part may pop out. 0.15 mA 30 24 Microload area 12 Invalid area 5 0 0.1 1 mA 1 10 100 1,000 Current (mA) Operating Environment • The IP65 model is designed with a degree of protection so that it will not sustain damage if it is subjected to water from any direction to the front of the panel. 11 A165K Others • The oil-resistant IP65 uses NBR rubber and is resistant to general cutting oil and cooling oil. Some particular oils cannot be used with the oil-resistant IP65, however, so contact your OMRON representative for details. • If the panel is to be finished with coating, etc., make sure that the panel meets the specified dimensions after the coating. • Do not subject the Switch to extreme shock or vibration. Doing so will cause malfunctions and damage to the Switch. Do not let sharp objects come into contact with the Switches that are made of resin. Doing so will damage the Switches, causing scratches on the outside of the operating parts, and malfunction. When handling the Switches, do not throw or drop them. Do not allow the Switch to drop and hit the ground. Do not place or drop heavy objects on the Switch. Do not operate the Switch with hard or sharp objects. Hammer Screwdriver 12 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: • Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. • Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. • Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. 2009.9 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2009 All Right Reserved. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Omron: A16ZJ-3003 A16ZJ-5050 A16ZA-5001W