ES1A THRU ES1J SURFACE MOUNT SUPER FAST RECTIFIER Reverse Voltage - 50 to 600 Volts Forward Current - 1.0 Ampere DO-214AC FEATURES The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 For surface mounted applications Super fast switching for high efficiency Low reverse leakage Built-in strain relief,ideal for automated placement High forward surge current capability High temperature soldering guaranteed: 250 C/10 seconds at terminals 0.110(2.80) 0.100(2.54) 0.087 (2.21) 0.070 (1.80) 0.177(4.50) 0.157(3.99) 0.012(0.305) 0.006(0.152) A MECHANICAL DATA 0.060(1.52) 0.030(0.76) 0.008(0.203)MAX. Case: JEDEC DO-214AC molded plastic body Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight:0.003 ounce, 0.093 grams 0.004 ounce, 0.111 grams SMA(H) 0.222(5.66) 0.194(4.93) SMA A: 0.096(2.42) 0.078(1.98) SMA(H) 0.122(3.12) 0.110(2.82) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. SYMBOLS ES1A ES1B Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TL=55 C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 1.0A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range VRRM VRMS VDC 50 35 50 100 70 100 ES1C 150 105 150 ES1D ES1E 200 140 200 300 210 300 ES1G ES1J UNITS 400 280 400 600 420 600 VOLTS VOLTS VOLTS I(AV) 1.0 Amp IFSM 30.0 Amps VF 1.25 0.95 5.0 50.0 IR Volts uA trr 35 ns CJ 15.0 60.0 -65 to +150 pF C/W C RqJA TJ,TSTG Note:1.Reverse recovery condition IF=0.5A,IR=1.0A,Irr=0.25A 2.Measured at 1MHz and applied reverse voltage of 4.0V D.C. 3.P.C.B. mounted with 0.2x0.2”(5.0x5.0mm) copper pad areas www.shunyegroup.com.cn RATINGS AND CHARACTERISTIC CURVES ES1A THRU ES1J AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1- FORWARD CURRENT DERATING CURVE 0.8 0.6 Single Phase Half Wave 60Hz Resistive or inductive Load 0.4 0.2 0 0 25 50 30 £PEAK FORWARD SURGE CURRENT, AMPERES 1.0 FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 75 100 125 150 25 20 15 10 175 5.0 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 10 AMBIENT TEMPERATURE, C FIG. 4-TYPICAL REVERSE CHARACTERISTICS FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1,000 10 TJ=25 C PULSE WIDTH=300 ms 1%DUTY CYCLE 1 0.1 ES1A-ES1D ES1E-ES1J 0.01 0 0.4 0.8 1.2 1.6 1.8 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES 20 100 10 TJ=100 C 1 0.1 TJ=25 C 0.01 INSTANTANEOUS FORWARD VOLEAGE, VOLTS 20 40 60 80 TJ=25 C 10 100 10 1 0.1 0.01 0.1 1 10 1 0.1 1.0 10 100 REVERSE VOLTAGE,VOLTS 100 FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/W FIG. 5-TYPICAL JUNCTION CAPACITANCE 100 0 PERCENT OF PEAK REVERSE VOLTAGE,% 200 JUNCTION CAPACITANCE, pF 100 NUMBER OF CYCLES AT 60 Hz t.,PULSE DURATION,sec. www.shunyegroup.com.cn 100