AD CED1Z 8-channel differential das with 18-bit Datasheet

8-Channel Differential DAS with 18-Bit,
Bipolar, Simultaneous Sampling ADC
AD7609
Data Sheet
FEATURES
APPLICATIONS
8 simultaneously sampled inputs
True differential inputs
True bipolar analog input ranges: ±10 V, ±5 V
Single 5 V analog supply and 2.3 V to 5.25 V VDRIVE
Fully integrated data acquisition solution
Analog input clamp protection
Input buffer with 1 MΩ analog input impedance
Second-order antialiasing analog filter
On-chip accurate reference and reference buffer
18-bit ADC with 200 kSPS on all channels
Oversampling capability with digital filter
Flexible parallel/serial interface
SPI/QSPI™/MICROWIRE™/DSP compatible
Performance
7 kV ESD rating on analog input channels
98 dB SNR, −107 dB THD
Dynamic range: up to 105 dB typical
Low power: 100 mW
Standby mode: 25 mW
64-lead LQFP package
Power line monitoring and protection systems
Multiphase motor control
Instrumentation and control systems
Multiaxis positioning systems
Data acquisition systems (DAS)
COMPANION PRODUCTS
External References: ADR421, ADR431
Digital Isolators: ADuM1402, ADuM5000, ADuM5402
Power: ADIsimPower, Supervisor Parametric Search
Additional companion products on the AD7609 product page
Table 1. High Resolution, Bipolar Input, Simultaneous
Sampling DAS Solutions
SingleEnded
Inputs
AD7608
AD7606
AD7606-6
AD7606-4
AD7607
Resolution
18 Bits
16 Bits
14 Bits
1
True
Differential
Inputs
AD7609 1
Number of
Simultaneous
Sampling Channels
8
8
6
4
8
Patent pending.
FUNCTIONAL BLOCK DIAGRAM
AVCC
CLAMP
V1–
CLAMP
V2+
CLAMP
V2–
CLAMP
V3+
CLAMP
V3–
CLAMP
V4+
CLAMP
V4–
CLAMP
V5+
CLAMP
V5–
V6+
V6–
CLAMP
CLAMP
CLAMP
V7+
CLAMP
V7–
CLAMP
V8+
CLAMP
V8–
CLAMP
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
1MΩ
RFB
SECONDORDER LPF
AVCC
REGCAP
REGCAP
2.5V
LDO
2.5V
LDO
REFCAPB
REFCAPA
T/H
REFIN/REFOUT
SECONDORDER LPF
T/H
2.5V
REF
SECONDORDER LPF
T/H
REF SELECT
AGND
OS 2
OS 1
OS 0
SECONDORDER LPF
T/H
SERIAL
8:1
MUX
SECONDORDER LPF
T/H
18-BIT
SAR
DIGITAL
FILTER
PARALLEL/
SERIAL
INTERFACE
DOUTA
DOUTB
RD/SCLK
CS
PAR/SER SEL
VDRIVE
SECONDORDER LPF
T/H
PARALLEL
DB[15:0]
AD7609
SECONDORDER LPF
SECONDORDER LPF
T/H
CLK OSC
CONTROL
INPUTS
T/H
AGND
CONVST A CONVST B RESET RANGE
BUSY
FRSTDATA
09760-001
V1+
1MΩ
Figure 1.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2011–2012 Analog Devices, Inc. All rights reserved.
AD7609
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Converter Details ....................................................................... 21
Applications ....................................................................................... 1
Analog Input ............................................................................... 21
Companion Products ....................................................................... 1
ADC Transfer Function ............................................................. 22
Functional Block Diagram .............................................................. 1
Internal/External Reference ...................................................... 23
Revision History ............................................................................... 2
Typical Connection Diagram ................................................... 24
General Description ......................................................................... 3
Power-Down Modes .................................................................. 24
Specifications..................................................................................... 4
Conversion Control ................................................................... 25
Timing Specifications .................................................................. 7
Digital Interface .............................................................................. 26
Absolute Maximum Ratings.......................................................... 11
Parallel Interface (PAR/SER SEL = 0) ...................................... 26
Thermal Resistance .................................................................... 11
Serial Interface (PAR/SER SEL = 1) ......................................... 26
ESD Caution ................................................................................ 11
Reading During Conversion ..................................................... 27
Pin Configuration and Function Descriptions ........................... 12
Digital Filter ................................................................................ 28
Typical Performance Characteristics ........................................... 15
Layout Guidelines....................................................................... 32
Terminology .................................................................................... 19
Outline Dimensions ....................................................................... 34
Theory of Operation ...................................................................... 21
Ordering Guide .......................................................................... 34
REVISION HISTORY
2/12—Rev. 0 to Rev. A
Changes to Analog Input Ranges Section ....................................21
7/11—Revision 0: Initial Version
Rev. A | Page 2 of 36
Data Sheet
AD7609
GENERAL DESCRIPTION
The AD7609 is an 18-bit, 8-channel, true differential,
simultaneous sampling analog-to-digital data acquisition
system (DAS). The part contains analog input clamp protection,
a second-order antialiasing filter, a track-and-hold amplifier, an
18-bit charge redistribution successive approximation analogto-digital converter (ADC), a flexible digital filter, a 2.5 V
reference and reference buffer, and high speed serial and
parallel interfaces.
The AD7609 operates from a single 5 V supply and can
accommodate ±10 V and ±5 V true bipolar differential input
signals while sampling at throughput rates up to 200 kSPS for
all channels. The input clamp protection circuitry can tolerate
voltages up to ±16.5 V. The AD7609 has 1 MΩ analog input
impedance regardless of sampling frequency. The single supply
operation, on-chip filtering, and high input impedance eliminate the need for driver op amps and external bipolar supplies.
The AD7609 antialiasing filter has a −3 dB cutoff frequency of
32 kHz and provides 40 dB antialias rejection when sampling
at 200 kSPS. The flexible digital filter is pin driven, yields
improvements in SNR, and reduces the −3 dB bandwidth.
Rev. A | Page 3 of 36
AD7609
Data Sheet
SPECIFICATIONS
VREF = 2.5 V external/internal, AVCC = 4.75 V to 5.25 V, VDRIVE = 2.3 V to 5.25 V; fSAMPLE = 200 kSPS, TA = TMIN to TMAX, unless otherwise
noted. 1
Table 2.
Parameter
DYNAMIC PERFORMANCE
Signal-to-Noise Ratio (SNR) 2, 3
Signal-to-(Noise + Distortion) (SINAD)2
Dynamic Range
Total Harmonic Distortion (THD)2, 3
Peak Harmonic or Spurious Noise (SFDR)2
Intermodulation Distortion (IMD)2
Second-Order Terms
Third-Order Terms
Channel-to-Channel Isolation2
ANALOG INPUT FILTER
Full Power Bandwidth
tGROUP DELAY
DC ACCURACY
Resolution
Differential Nonlinearity2
Integral Nonlinearity2
Total Unadjusted Error (TUE)
Positive Full-Scale Error2, 5
Positive Full-Scale Error Drift
Positive Full-Scale Error Matching2
Bipolar Zero Code Error2, 6
Bipolar Zero Code Error Drift
Bipolar Zero Code Error Matching2
Negative Full-Scale Error2, 5
Negative Full-Scale Error Drift
Negative Full-Scale Error Matching2
Test Conditions/Comments
fIN = 1 kHz sine wave unless otherwise noted
Oversampling by 16; ±10 V range; fIN = 160 Hz
Oversampling by 16; ±5 V range; fIN = 160 Hz
No oversampling; ±10 V range
No oversampling; ±5 V range
No oversampling; ±10 V range
No oversampling; ±5 V range
No oversampling; ±10 V range
No oversampling; ±5 V range
No oversampling; ±10 V range
No oversampling; ±5 V range
Min
Typ
98
101
100
91
90.5
91
90
91.5
90.5
−107
−110
−108
90
89.5
89.5
89
Max
−97
−96
Unit
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
fa = 1 kHz, fb = 1.1 kHz
fIN on unselected channels up to 160 kHz
−110
−106
−95
dB
dB
dB
−3 dB, ±10 V range
−3 dB, ±5 V range
−0.1 dB, ±10 V range
−0.1 dB, ±5 V range
±10 V range
±5 V range
32
23
13
10
7.1
10.2
kHz
kHz
kHz
kHz
µs
µs
No missing codes
±10 V range
±5 V range
External reference
Internal reference
External reference
Internal reference
±10 V range
±5 V range
±10 V range
± 5 V range
±10 V range
± 5 V range
±10 V range
±5 V range
External reference
Internal reference
External reference
Internal reference
±10 V range
±5 V range
Rev. A | Page 4 of 36
18
±0.75
±3
±10
±90
±8
±40
±2
±7
12
40
±3
±3
10
5
2.7
13
±8
±40
±4
±8
12
40
−0.99/+2
±7.5
±140
80
100
±24
±48
30
65
±140
80
100
Bits
LSB 4
LSB
LSB
LSB
LSB
LSB
ppm/°C
ppm/°C
LSB
LSB
LSB
LSB
µV/°C
µV/°C
LSB
LSB
LSB
LSB
ppm/°C
ppm/°C
LSB
LSB
Data Sheet
Parameter
ANALOG INPUT
Differential Input Voltage Ranges
Absolute Voltage Input
Common-Mode Input Range
CMRR
Analog Input Current
Input Capacitance 7
Input Impedance
REFERENCE INPUT/OUTPUT
Reference Input Voltage Range
DC Leakage Current
Input Capacitance7
Reference Output Voltage
Reference Temperature Coefficient
LOGIC INPUTS
Input High Voltage (VINH)
Input Low Voltage (VINL)
Input Current (IIN)
Input Capacitance (CIN)7
LOGIC OUTPUTS
Output High Voltage (VOH)
Output Low Voltage (VOL)
Floating-State Leakage Current
Floating-State Output Capacitance7
Output Coding
CONVERSION RATE
Conversion Time
Track-and-Hold Acquisition Time
Throughput Rate
POWER REQUIREMENTS
AVCC
VDRIVE
ITOTAL
Normal Mode (Static)
Normal Mode (Operational)8
Standby Mode
Shutdown Mode
AD7609
Test Conditions/Comments
VIN = Vx+ − (Vx−)
RANGE = 1; ±10 V
RANGE = 0; ±5 V
±10 V range, see the Analog Input Clamp
Protection section
±5 V range, see the Analog Input Clamp
Protection section
Min
Typ
Max
Unit
−20
−10
−10
+20
+10
+10
V
V
V
−5
+5
V
−4
±5
−70
5.4
2.5
5
1
+4
V
dB
µA
µA
pF
MΩ
2.475
2.5
2.525
±1
V
µA
pF
V
10 V, see Figure 28
5 V, see Figure 28
REF SELECT = 1
REFIN/REFOUT
7.5
2.49/
2.505
±10
ppm/°C
0.7 × VDRIVE
0.3 × VDRIVE
±2
V
V
µA
pF
0.2
±20
V
V
µA
pF
5
ISOURCE = 100 µA
ISINK = 100 µA
VDRIVE − 0.2
±1
5
Twos complement
All eight channels included
4
1
Per channel, all eight channels included
4.75
2.3
200
µs
µs
kSPS
5.25
5.25
V
V
22
28.5
8
11
mA
mA
mA
µA
Digital inputs = 0 V or VDRIVE
16
20
5
2
fSAMPLE = 200 kSPS
Rev. A | Page 5 of 36
AD7609
Parameter
Power Dissipation
Normal Mode (Static)
Normal Mode (Operational) 8
Standby Mode
Shutdown Mode
Data Sheet
Test Conditions/Comments
fSAMPLE = 200 kSPS
Min
Typ
Max
Unit
80
100
25
10
115.5
157
42
60.5
mW
mW
mW
µW
Temperature range for B version is −40°C to +85°C.
See the Terminology section.
This specification applies when reading during a conversion or after a conversion. If reading during a conversion in parallel and serial modes with VDRIVE = 5 V, SNR typically reduces
by 1.5 dB and THD by 3 dB.
4
LSB means least significant bit. With ±5 V input range, 1 LSB = 76.29 µV. With ±10 V input range, 1 LSB = 152.58 µV.
5
These specifications include the full temperature range variation and contribution from the internal reference buffer but do not include the error contribution from
the external reference.
6
Bipolar zero code error is calculated with respect to the analog input voltage. See the Analog Input Clamp Protection section.
7
Sample tested during initial release to ensure compliance.
8
Operational power/current figure includes contribution when running in oversampling mode.
1
2
3
Rev. A | Page 6 of 36
Data Sheet
AD7609
TIMING SPECIFICATIONS
AVCC = 4.75 V to 5.25 V, VDRIVE = 2.3 V to 5.25 V, VREF = 2.5 V external reference/ internal reference, TA = TMIN to TMAX,
unless otherwise noted. 1
Table 3.
Parameter
PARALLEL/SERIAL/BYTE MODE
tCYCLE
Limit at TMIN, TMAX
Min
Typ Max
Unit
5
µs
10.1
11.5
µs
µs
µs
4.15
9.1
18.8
39
78
158
315
100
µs
µs
µs
µs
µs
µs
µs
µs
30
ms
13
ms
5
tCONV
3.45
7.87
16.05
33
66
133
257
tWAKE-UP STANDBY
tWAKE-UP SHUTDOWN
Internal Reference
External Reference
tRESET
tOS_SETUP
tOS_HOLD
t1
t2
t3
t4
t5 2
t6
t7
PARALLEL READ OPERATION
t8
t9
t10
t11
t12
4
50
20
20
25
ns
ns
ns
ns
ns
ns
ns
ms
ns
ns
0
0
ns
ns
19
24
30
37
15
22
ns
ns
ns
ns
ns
ns
45
25
25
0
0.5
25
Description
1/throughput rate
Parallel mode, reading during; or after conversion VDRIVE = 2.7 V to 5.25 V; or
serial mode: VDRIVE = 3.3 V to 5.25 V, reading during a conversion using DOUTA
and DOUTB lines
Parallel mode reading after conversion VDRIVE = 2.3 V
Serial mode reading after conversion; VDRIVE = 2.7 V, DOUTA and DOUTB lines
Serial mode reading after a conversion; VDRIVE = 2.3 V, DOUTA and DOUTB lines
Conversion time
Oversampling off
Oversampling by 2
Oversampling by 4
Oversampling by 8
Oversampling by 16
Oversampling by 32
Oversampling by 64
STBY rising edge to CONVST x rising edge; power-up time from standby mode
STBY rising edge to CONVST x rising edge; power-up time from
shutdown mode
STBY rising edge to CONVST x rising edge; power-up time from
shutdown mode
RESET high pulse width
BUSY to OS x pin setup time
BUSY to OS x pin hold time
CONVST x high to BUSY high
Minimum CONVST x low pulse
Minimum CONVST x high pulse
BUSY falling edge to CS falling edge setup time
Maximum delay allowed between CONVST A, CONVST B rising edges
Maximum time between last CS rising edge and BUSY falling edge
Minimum delay between RESET low to CONVST x high
CS to RD setup time
CS to RD hold time
RD low pulse width
VDRIVE above 4.75 V
VDRIVE above 3.3 V
VDRIVE above 2.7 V
VDRIVE above 2.3 V
RD high pulse width
CS high pulse width (see Figure 5); CS and RD linked
Rev. A | Page 7 of 36
AD7609
Parameter
t13
Data Sheet
Limit at TMIN, TMAX
Min
Typ Max
Unit
19
24
30
37
ns
ns
ns
ns
19
24
30
37
22
ns
ns
ns
ns
ns
ns
ns
20
15
12.5
10
MHz
MHz
MHz
MHz
18
23
35
ns
ns
ns
20
26
32
39
ns
ns
ns
ns
ns
ns
22
ns
18
23
30
35
18
23
30
35
ns
ns
ns
ns
ns
ns
ns
ns
ns
19
23
30
35
ns
ns
ns
ns
t143
t15
t16
t17
6
6
SERIAL READ OPERATION
fSCLK
t18
t19 3
t20
t21
t22
t23
0.4 tSCLK
0.4 tSCLK
7
FRSTDATA OPERATION
t24
t25
t26
Description
Delay from CS until DB[15:0] three-state disabled
VDRIVE above 4.75 V
VDRIVE above 3.3 V
VDRIVE above 2.7 V
VDRIVE above 2.3 V
Data access time after RD falling edge
VDRIVE above 4.75 V
VDRIVE above 3.3 V
VDRIVE above 2.7 V
VDRIVE above 2.3 V
Data hold time after RD falling edge
CS to DB[15:0] hold time
Delay from CS rising edge to DB[15:0] three-state enabled
Frequency of serial read clock
VDRIVE above 4.75 V
VDRIVE above 3.3 V
VDRIVE above 2.7 V
VDRIVE above 2.3 V
Delay from CS until DOUTA/DOUTB three-state disabled/delay from CS until
MSB valid
VDRIVE above 4.75 V
VDRIVE above 3.3 V
VDRIVE = 2.3 V to 2.7 V
Data access time after SCLK rising edge
VDRIVE above 4.75 V
VDRIVE above 3.3 V
VDRIVE above 2.7 V
VDRIVE above 2.3 V
SCLK low pulse width
SCLK high pulse width
SCLK rising edge to DOUTA/DOUTB valid hold time
CS rising edge to DOUTA/DOUTB three-state enabled
Delay from CS falling edge until FRSTDATA three-state disabled
VDRIVE above 4.75 V
VDRIVE above 3.3 V
VDRIVE above 2.7 V
VDRIVE above 2.3 V
Delay from CS falling edge until FRSTDATA high, serial mode
VDRIVE above 4.75 V
VDRIVE above 3.3 V
VDRIVE above 2.7 V
VDRIVE above 2.3 V
Delay from RD falling edge to FRSTDATA high
VDRIVE above 4.75 V
VDRIVE above 3.3 V
VDRIVE above 2.7 V
VDRIVE above 2.3 V
Rev. A | Page 8 of 36
Data Sheet
AD7609
Limit at TMIN, TMAX
Min
Typ Max
Parameter
t27
Unit
22
29
ns
ns
20
27
29
ns
ns
ns
t28
t29
Description
Delay from RD falling edge to FRSTDATA low
VDRIVE = 3.3 V to 5.25 V
VDRIVE = 2.3 V to 2.7 V
Delay from 18th SCLK falling edge to FRSTDATA low
VDRIVE = 3.3 V to 5.25 V
VDRIVE = 2.3 V to 2.7 V
Delay from CS rising edge until FRSTDATA three-state enabled
Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (30% to 70% of VDD) and timed from a voltage level of 1.6 V.
The delay between the CONVST x signals was measured as the maximum time allowed while ensuring a <40 LSB performance matching between channel sets.
3
A buffer is used on the data output pins for these measurements, which is equivalent to a load of 20 pF on the output pins.
1
2
Timing Diagrams
t5
CONVST A/
CONVST B
tCYCLE
CONVST A/
CONVST B
t2
t3
tCONV
t1
BUSY
t4
CS
t7
09760-002
tRESET
RESET
Figure 2. CONVST x Timing—Reading After a Conversion
t5
CONVST A/
CONVST B
tCYCLE
CONVST A/
CONVST B
t2
t3
tCONV
t1
BUSY
t6
CS
t7
09760-003
tRESET
RESET
Figure 3. CONVST x Timing—Reading During a Conversion
CS
t8
t16
t13
t14
DATA:
DB[15:0]
FRSTDATA
V1
[17:2]
INVALID
t24
t26
V1
[1:0]
V2
[17:2]
t17
t15
V2
[1:0]
V8
[17:2]
t27
Figure 4. Parallel Mode Separate CS and RD Pulses
Rev. A | Page 9 of 36
V8
[1:0]
t29
09760-004
RD
t9
t11
t10
AD7609
Data Sheet
t12
CS, RD
t16
t13
V1
[17:2]
V1
[1:0]
V2
[17:2]
V2
[1:0]
V7
[17:2]
V7
[1:0]
V8
[17:2]
t17
V8
[1:0]
09760-005
DATA:
DB[15:0]
FRSTDATA
Figure 5. CS and RD Linked Parallel Mode
CS
t21
SCLK
t19
t18
DOUTA,
DOUTB
t20
DB17
t22
DB14
DB13
t25
DB1
t23
DB0
t29
09760-006
t28
FRSTDATA
Figure 6. Serial Read Operation
Rev. A | Page 10 of 36
Data Sheet
AD7609
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 4.
Parameter
AVCC to AGND
VDRIVE to AGND
Analog Input Voltage to AGND 1
Digital Input Voltage to AGND
Digital Output Voltage to AGND
REFIN to AGND
Input Current to Any Pin Except
Supplies1
Operating Temperature Range
B Version
Storage Temperature Range
Junction Temperature
Pb/SN Temperature, Soldering
Reflow (10 sec to 30 sec)
Pb-Free Temperature, Soldering Reflow
ESD (All Pins Except Analog Inputs)
ESD (Analog Input Pins Only)
1
Rating
−0.3 V to +7 V
−0.3 V to AVCC + 0.3 V
±16.5 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to AVCC + 0.3 V
±10 mA
−40°C to +85°C
−65°C to +150°C
150°C
240(+0)°C
260(+0)°C
2 kV
7 kV
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages. These
specifications apply to a 4-layer board.
Table 5. Thermal Resistance
Package Type
64-Lead LQFP
ESD CAUTION
Transient currents of up to 100 mA do not cause SCR latch-up.
Rev. A | Page 11 of 36
θJA
45
θJC
11
Unit
°C/W
AD7609
Data Sheet
V1–
V1+
V2–
V2+
V3–
V3+
V4–
V4+
V5–
64 63 62 61 60 59 58
V5+
V6–
V6+
V7+
V7–
V8+
V8–
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
57 56 55 54 53 52 51 50 49
48 AVCC
AVCC 1
ANALOG INPUT
DECOUPLING CAPACITOR PIN
PIN 1
AGND 2
OS 0 3
POWER SUPPLY
OS 1 4
GROUND PIN
OS 2 5
47 AGND
46 REFGND
45 REFCAPB
44 REFCAPA
PAR/SER SEL 6
DATA OUTPUT
STBY 7
DIGITAL OUTPUT
REFERENCE INPUT/OUTPUT
42 REFIN/REFOUT
TOP VIEW
(Not to Scale)
RANGE 8
DIGITAL INPUT
43 REFGND
AD7609
41 AGND
CONVST A 9
40 AGND
CONVST B 10
39 REGCAP
RESET 11
38 AVCC
RD/SCLK 12
37 AVCC
36 REGCAP
CS 13
BUSY 14
35 AGND
FRSTDATA 15
DB0 16
34 REF SELECT
33 DB15
09760-007
DB14
DB13
DB12
DB11
DB9
DB10
AGND
DB8/DOUTB
VDRIVE
DB7/DOUTA
DB6
DB5
DB4
DB3
DB2
DB1
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Figure 7. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
1, 37, 38, 48
Type 1
P
Mnemonic
AVCC
2, 26, 35,
40, 41, 47
P
AGND
23
P
VDRIVE
36, 39
P
REGCAP
49, 51, 53,
55, 57, 59,
61, 63
50, 52, 54,
56, 58, 60,
62, 64
42
AI+
V1+ to V8+
AI−
V1− to V8−
REF
REFIN/
REFOUT
34
DI
REF SELECT
44, 45
REF
43, 46
REF
REFCAPA,
REFCAPB
REFGND
Description
Analog Supply Voltage 4.75 V to 5.25 V. This supply voltage is applied to the internal front-end
amplifiers and to the ADC core. These supply pins should be decoupled to AGND.
Analog Ground. This pin is the ground reference point for all analog circuitry on the AD7609. All
analog input signals and external reference signals should be referred to these pins. All six of these
AGND pins should connect to the AGND plane of a system.
Logic Power Supply Input. The voltage (2.3 V to 5 V) supplied at this pin determines the operating
voltage of the interface. This pin is nominally at the same supply as the supply of the host interface
(that is, DSP, FPGA).
Decoupling Capacitor Pins for Voltage Output from Internal Regulator. These output pins should be
decoupled separately to AGND using a 1 μF capacitor. The voltage on these output pins is in the
range of 2.5 V to 2.7 V.
Analog Input V1+ to Analog Input V8+. These pins are the positive terminal of the true differential
analog inputs. The analog input range of these channels is determined by the RANGE pin.
Analog Input V1− to Analog Input V8−. These are the negative terminals of the true differential
analog inputs. The analog input range of these channels is determined by the RANGE pin. The signal
on this pin should be 180° out of phase with the corresponding Vx+ pin.
Reference Input/ Reference Output. The on-chip reference of 2.5 V is available on this pin for external
use if the REF SELECT pin is set to a logic high. Alternatively, the internal reference can be disabled by
setting the REF SELECT pin to a logic low and an external reference of 2.5 V can be applied to this
input. See the Internal/External Reference section. Decoupling is required on this pin for both the
internal or external reference options. A 10 µF capacitor should be applied from this pin to ground
close to the REFGND pins.
Internal/External Reference Selection Input. Logic input. If this pin is set to logic high, the internal
reference is selected and is enabled. If this pin is set to logic low, the internal reference is disabled and
an external reference voltage must be applied to the REFIN/REFOUT pin.
Reference Buffer Output Force/Sense Pins. These pins must be connected together and decoupled to
AGND using a low ESR 10 μF ceramic capacitor.
Reference Ground Pins. These pins should be connected to AGND.
Rev. A | Page 12 of 36
Data Sheet
AD7609
Pin No.
8
Type 1
DI
Mnemonic
RANGE
6
DI
PAR/
SER SEL
9, 10
DI
CONVST A,
CONVST B
13
DI
CS
12
DI
RD/SCLK
14
DO
BUSY
11
DI
RESET
15
DO
FRSTDATA
7
DI
STBY
Description
Analog Input Range Selection. Logic input. The polarity on this pin determines the input range of the
analog input channels. If this pin is tied to a logic high, the analog input range is ±10 V for all
channels. If this pin is tied to a logic low, the analog input range is ±5 V for all channels. A logic
change on this pin has an immediate effect on the analog input range. Changing this pin during a
conversion is not recommended. See the Analog Input section for more details.
Parallel/Serial Interface Selection Input. Logic input. If this pin is tied to a logic low, the parallel
interface is selected. If this pin is tied to a logic high, the serial interface is selected.
In serial mode, the RD/SCLK pin functions as the serial clock input. The DB7/DOUTA and DB8/DOUTB pins
function as serial data outputs.
When the serial interface is selected, the DB[15:9] and DB[6:0] pins should be tied to AGND.
Conversion Start Input A, Conversion Start Input B. Logic inputs. These logic inputs are used to initiate
conversions on the analog input channels. For simultaneous sampling of all input channels, CONVST A
and CONVST B can be shorted together and a single conversion start signal applied. Alternatively,
CONVST A can be used to initiate simultaneous sampling for V1, V2, V3, and V4, and CONVST B can be
used to initiate simultaneous sampling on the other analog inputs (V5, V6, V7, and V8). This is only
possible when oversampling is not switched on. When the CONVST A or CONVST B pin transitions
from low to high, the front-end track-and-hold circuitry for their respective analog inputs is set to
hold. This function allows a phase delay to be created inherently between the sets of analog inputs.
Chip Select. This active low logic input frames the data transfer. When both CS and RD are logic low in
parallel mode, the output bus (DB[15:0]) is enabled and the conversion result is output on the parallel
data bus lines. In serial mode, the CS is used to frame the serial read transfer and clocks out the MSB
of the serial output data.
Parallel Data Read Control Input When Parallel Interface is Selected (RD)/Serial Clock Input When
Serial Interface is Selected (SCLK). When both CS and RD are logic low in parallel mode, the output
bus is enabled. In parallel mode, two RD pulses are required to read the full 18 bits of conversion
results from each channel. The first RD pulse outputs DB[17:2], and the second RD pulses outputs
DB[1:0]. In serial mode, this pin acts as the serial clock input for data transfers. The CS falling edge
takes the data output lines, DOUTA and DOUTB, out of three-state and clocks out the MSB of the
conversion result. The rising edge of SCLK clocks all subsequent data bits onto the serial data
outputs, DOUTA and DOUTB. For further information, see the Conversion Control section.
Busy Output. This pin transitions to a logic high after both CONVST A and CONVST B rising edges and
indicates that the conversion process has started. The BUSY output remains high until the conversion
process for all channels is complete. The falling edge of BUSY signals that the conversion data is being
latched into the output data registers and will be available to be read after a time, t4. Any data read
while BUSY is high should be complete before the falling edge of BUSY occurs. Rising edges on
CONVST A or CONVST B have no effect while the BUSY signal is high.
Reset Input. When set to logic high, the rising edge of RESET resets the AD7609. The part must receive
a RESET pulse after power-up. To achieve the specified performance after the RESET signal, the tWAKE_UP
SHUTDOWN time should elapse between power-on and the RESET pulse. The RESET high pulse should be
typically 100 ns wide. If a RESET pulse is applied during a conversion, the conversion is aborted. If a
RESET pulse is applied during a read, the contents of the output registers reset to all zeros.
Digital Output. The FRSTDATA output signal indicates when the first channel, V1, is being read back
on either the parallel or serial interface. When the CS input is high, the FRSTDATA output pin is in
three-state. The falling edge of CS takes FRSTDATA out of three-state. In parallel mode, the falling
edge of RD corresponding to the result of V1 then sets the FRSTDATA pin high, indicating that the
result from V1 is available on the output data bus. The FRSTDATA output returns to a logic low
following the third falling edge of RD. In serial mode, FRSTDATA goes high on the falling edge of CS
as this clocks out the MSB of V1 on DOUTA. It returns low on the 18th SCLK falling edge after the CS
falling edge. See the Conversion Control section for more details.
Standby Mode Input. This pin is used to place the AD7609 into one of two power-down modes:
standby mode or shutdown mode. The power-down mode entered depends on the state of the
RANGE pin, as shown in Table 8. When in standby mode, all circuitry except the on-chip reference,
regulators, and regulator buffers is powered down. When in shutdown mode, all circuitry is
powered down.
Rev. A | Page 13 of 36
AD7609
Data Sheet
Pin No.
5, 4, 3
Type 1
DI
Mnemonic
OS [2:0]
33
DO/DI
DB15
32
DO/DI
DB14
31 to 27
DO
DB[13:9]
24
DO
DB7/DOUTA
25
DO
DB8/DOUTB
22 to 16
DO
DB[6:0]
1
Description
Oversampling Mode Pins. Logic inputs. These inputs are used to select the oversampling ratio. OS 2 is
the MSB control bit, and OS 0 is the LSB control bit. See the Digital Filter section for additional details
on the oversampling mode of operation and Table 9 for oversampling bit decoding.
Parallel Output Data Bits, Data Bit 15. When PAR/SER SEL = 0, this pin acts as three-state parallel digital
output pin. This pin is used to output DB17 of the conversion result during the first RD pulse and DB1
of the same conversion result during the second RD pulse. When PAR/SER SEL = 1, this pin should be
tied to AGND.
Parallel Output Data Bits, Data Bit 14. When PAR/SER SEL = 0, this pin acts as three-state parallel digital
output pin. When CS and RD are low, this pin is used to output DB16 of the conversion result during
the first RD pulse and DB0 of the same conversion result during the second RD pulse. When PAR/SER
SEL = 1, this pin should be tied to AGND.
Parallel Output Data Bits, Data Bit 13 to Data Bit 9. When PAR/SER SEL = 0, these pins act as three-state
parallel digital input/output pins. When CS and RD are low, these pins are used to output DB15 to
DB11 of the conversion result during the first RD pulse and output 0 during the second RD pulse.
When PAR/SER SEL = 1, these pins should be tied to AGND.
Parallel Output Data Bit 7 (DB7)/Serial Interface Data Output Pin (DOUTA). When PAR/SER SEL = 0, this
pins acts as a three-state parallel digital input/output pin. When CS and RD are low, this pin is used to
output DB9 of the conversion result. When PAR/SER SEL = 1, this pin functions as DOUTA and outputs
serial conversion data. See the Conversion Control section for further details.
Parallel Output Data Bit 8 (DB8)/Serial Interface Data Output Pin (DOUTB). When PAR/SER SEL = 0, this
pins acts as a three-state parallel digital input/output pin. When CS and RD are low, this pin is used to
output DB10 of the conversion result. When PAR/SER SEL = 1, this pin functions as DOUTB and outputs
serial conversion data. See the Conversion Control section for further details.
Parallel Output Data Bits, Data Bit 6 to Data Bit 0. When PAR/SER SEL = 0, these pins act as three-state
parallel digital input/output pins. When CS and RD are low, these pins are used to output DB8 to DB2
of the conversion result during the first RD pulse and output 0 during the second RD pulse. When
PAR/SER SEL = 1, these pins should be tied to AGND.
Refers to classification of pin type; P denotes power, AI denotes analog input, REF denotes reference, DI denotes digital input, DO denotes digital output.
Rev. A | Page 14 of 36
Data Sheet
AD7609
TYPICAL PERFORMANCE CHARACTERISTICS
3
0
AVCC, VDRIVE = 5V
INTERNAL REFERENCE
±10V RANGE
fSAMPLE = 200 kSPS
fIN = 1kHz
16384 POINT FFT
SNR = 91.52dB
THD = –111.05dB
–40
1
–80
0
±10V RANGE
AVCC, VDRIVE = 5V
TA = 25°C
fSAMPLE = 200 kSPS
WCP INL = 1.69 LSB
WCN INL = –1.3 LSB
–1
–100
–2
–120
–140
CODE
Figure 8. FFT Plot, ±10 V Range
09760-010
100k
229,376
80k
196,608
60k
131,072
40k
INPUT FREQUENCY (Hz)
98,304
20k
65,536
0
32,768
–160
09760-008
0
–3
163,840
SNR (dB)
–60
2
INL (LSB)
–20
Figure 11. Typical INL, ±10 V Range
1.0
AVCC, VDRIVE = 5V
INTERNAL REFERENCE
±5V RANGE
fSAMPLE = 200kSPS
f IN = 1kHz
16,384 POINT FFT
SNR = 91.12dB
THD = –109.77dB
–40
–60
0.6
0.4
DNL (LSB)
–20
AMPLITUDE (dB)
±10V RANGE
AVCC, VDRIVE = 5V
TA = 25°C
fSAMPLE = 200 kSPS
WCP DNL = 0.33 LSB
WCN DNL = –0.32 LSB
0.8
0
–80
0.2
0
–0.2
–0.4
–100
–0.6
–120
–0.8
–140
CODE
Figure 9. FFT Plot, ±5 V Range
09760-011
229,376
100k
196,608
80k
163,840
60k
131,072
40k
INPUT FREQUENCY (Hz)
98,304
20k
65,536
0
32,768
–160
09760-009
0
–1.0
Figure 12. Typical DNL, ±10 V Range
3
0
–60
1
INL (LSB)
–40
–80
0
–1
±5V RANGE
AVCC, VDRIVE = 5V
TA = 25°C
fSAMPLE = 200 kSPS
WCP INL = 1.56 LSB
WCN INL = –1.22 LSB
–100
–2
–120
–140
Figure 10. FFT Plot, ±10 V Range
CODE
Figure 13. Typical INL, ±5 V Range
Rev. A | Page 15 of 36
09760-012
6
229,376
5
196,608
4
163,840
3
131,072
2
INPUT FREQUENCY (kHz)
98,304
1
65,536
0
32,768
0
–3
–160
09760-109
AMPLITUDE (dB)
2
AVCC , VDRIVE = 5V
INTERNAL REFERENCE
±10V RANGE
fSAMPLE = 12.5kSPS
fIN = 1Hz
8192 POINT FFT
SNR = 100.71dB
THD: –111.74 dB
–20
AD7609
Data Sheet
±5V RANGE
AVCC, VDRIVE = 5V
TA = 25°C
fSAMPLE = 200 kSPS
WCP INL = 0.45 LSB
WCN INL = –0.38 LSB
0.6
32
0.2
0
–0.2
–0.4
–0.6
–0.8
16
8
0
–8
–16
–24
–40
–40
09760-013
229,376
196,608
163,840
131,072
98,304
65,536
CODE
±10V RANGE
AVCC, VDRIVE = 5V
EXTERNAL REFERENCE
–25
–10
20
65
80
8
±10V RANGE
20
±5V RANGE
0
–20
6
4
AVCC, VDRIVE = 5V
fSAMPLE = 200 kSPS
TA = 25°C
EXTERNAL REFERENCE
SOURCE RESISTANCE IS MATCHED ON
THE V– INPUT
±10V AND ±5V RANGE
2
–40
0
200kSPS
AVCC, VDRIVE = 5V
EXTERNAL REFERENCE
–25
–10
5
20
35
50
65
80
TEMPERATURE (°C)
–2
09760-117
–60
0
20k
40k
60k
80k
100k
120k
SOURCE RESISTANCE (Ω)
09760-219
PFS/NFS ERROR (%FS)
40
Figure 18. PFS and NFS Error vs. Source Resistance
Figure 15. NFS Error vs. Temperature
105
80
AVCC, VDRIVE = 5V
fSAMPLE CHANGES WITH OS RATE
60
TA = 25°C
INTERNAL REFERENCE
±10V RANGE
100
40
0
SNR (dBs)
20
±5V RANGE
–20
95
90
NO OS
OS × 2
OS × 4
OS × 8
OS × 16
OS × 32
OS × 64
±10V RANGE
–40
85
200kSPS
AVCC, VDRIVE = 5V
EXTERNAL REFERENCE
–60
–25
–10
5
20
35
50
TEMPERATURE (°C)
65
80
80
09760-118
PFS ERROR (LSB)
50
10
60
–80
–40
35
Figure 17. NFS and PFS Error Matching
80
–80
–40
5
TEMPERATURE (°C)
Figure 14. Typical DNL, ±5 V Range
NFS ERROR (LSB)
NFS ERROR
–32
32,768
0
–1.0
PFS ERROR
24
10
100
10k
10k
INPUT FREQUENCY (Hz)
Figure 19. SNR vs. Input Frequency, ±10 V Range
Figure 16. PFS Error vs. Temperature
Rev. A | Page 16 of 36
100k
09760-017
DNL (LSB)
0.4
40
NFS/PFS CHANNEL MATCHING (LSB)
0.8
09760-218
1.0
Data Sheet
AD7609
8
105
AVCC, VDRIVE = 5V
fSAMPLE CHANGES WITH OS RATE
TA = 25°C
INTERNAL REFERENCE
±5V RANGE
95
90
NO OS
OS × 2
OS × 4
OS × 8
OS × 16
OS × 32
OS × 64
85
100
2
0
±5V RANGE
–2
±10V RANGE
200 kSPS
AV CC,VDRIVE = 5V
EXTERNAL REFERENCE
–4
80
10
4
10k
10k
100k
INPUT FREQUENCY (Hz)
–6
–40
0
–20
20
40
TEMPERATURE (°C)
60
80
09760-023
BIPOLAR ZERO ERROR (LSB)
6
09760-018
SNR (dBs)
100
Figure 23. Bipolar Zero Code Error vs. Temperature
Figure 20. SNR vs. Input Frequency, ±5 V Range
–70
–90
0Ω
10Ω
500Ω
1.2kΩ
5kΩ
10kΩ
–100
–120
1
10
FREQUENCY (kHz)
100
09760-020
–110
12
±5V RANGE
8
4
±10V RANGE
0
–4
–8
200kSPS
AVCC, VDRIVE = 5V
EXTERNAL REFERENCE
–12
–16
–40
–25
–10
5
20
35
50
65
80
TEMPERATURE (°C)
Figure 24. Bipolar Zero Code Error Matching Between Channels
Figure 21. THD vs. Input Frequency for Various Source Impedances,
±10 V Range
–50
–40
–50
–60
CHANNEL-TO-CHANNEL ISOLATION (dB)
±5V RANGE
AVCC, VDRIVE = 5V
TA = 25°C
fSAMPLE = 200 kSPS
RSOURCE MATCHED
ON Vx+, Vx– INPUTS
THD (dB)
–70
–80
0Ω
10Ω
500Ω
1.2kΩ
5kΩ
10kΩ
–90
–100
–120
1
10
FREQUENCY (kHz)
100
09760-019
–110
AV CC, VDRIVE = 5V
INTERNAL REFERENCE
AD7609 RECOMMENDED DECOUPLING USED
fSAMPLE = 200kSPS
TA = 25°C
–60
–70
–80
±10V RANGE
–90
±5V RANGE
–100
–110
–120
–130
–140
0
20
40
60
80
100
120
NOISE FREQUENCY (kHz)
Figure 25. Channel-to-Channel Isolation
Figure 22. THD vs. Input Frequency for Various Source Impedances,
±5 V Range
Rev. A | Page 17 of 36
140
160
09760-225
THD (dB)
–80
16
09760-224
±10V RANGE
AVCC, VDRIVE = 5V
TA = 25°C
fSAMPLE = 200 kSPS
RSOURCE MATCHED
ON Vx+, Vx– INPUTS
BIPOLAR ZERO CODE ERROR MATCHING (LSB)
–60
AD7609
Data Sheet
22
110
20
±5V RANGE
95
90
85
AVCC = VDRIVE = 5V
TA = 25°C
INTERNAL REFERENCE
fSAMPLE SCALES WITH OS RATIO
80
NO OS
OS × 2
OS × 4 OS × 8 OS × 16 OS × 32 OS × 64
OVERSAMPLING RATIO
09760-023
DYNAMIC RANGE (dB)
±10V RANGE
100
18
16
14
12
AVCC, VDRIVE = 5V
10 TA = 25°C
INTERNAL REFERENCE
fSAMPLE VARIES WITH OS RATE
8
NO OS
OS × 2
OS × 4
OS × 8
OS × 16
OS × 32
OS × 64
OVERSAMPLING RATIO
Figure 26. Dynamic Range vs. Oversampling Ratio
09760-227
AVCC SUPPLY CURRENT (mA)
105
Figure 29. Supply Current vs. Oversampling Rate
140
AVCC = 5.25V
REFOUT VOLTAGE (V)
AVCC = 5V
2.5000
2.4995
AVCC = 4.75V
2.4990
2.4985
130
120
±10V RANGE
110
±5V RANGE
100
90
80
AVCC, VDRIVE = 5V
INTERNAL REFERENCE
AD7609 RECOMMENDED DECOUPLING USED
fSAMPLE = 200kSPS
TA = 25°C
70
60
–25
–10
5
20
35
50
65
80
TEMPERATURE (°C)
0
09760-029
2.4980
–40
100
200
300
400
500
600
700
800
09760-130
2.5005
POWER SUPPLY REJECTION RATIO (dB)
2.5010
900 1000 1100
AVCC NOISE FREQUENCY (kHz)
Figure 27. Reference Output Voltage vs. Temperature for Different Supply
Voltages
Figure 30. PSRR
0
10
AVCC, VDRIVE = 5V
fSAMPLE = 200kSPS
AVCC, VDRIVE = 5V
TA = 25°C
–10
fSAMPLE = 200kSPS
INTERNAL REFERENCE
–20
5
CMRR (dB)
–5
–15
–20
–15
–10
–5
0
±5V RANGE
–50
–60
±10V RANGE
–80
–90
5
10
15
DIFFERENTIAL ANALOG INPUT VOLTAGE (Vx+ – (Vx–)) (V)
20
Figure 28. Analog Input Current vs. Input Voltage Over Temperature
Rev. A | Page 18 of 36
–100
10
100
1k
10k
FREQUENCY (Hz)
Figure 31. CMRR vs. Common-Mode Ripple Frequency
100k
09760-028
–10
–40
–70
+25°C V+
+25°C V–
+85°C V–
+85°C V+
–40°C V–
–40°C V+
09760-025
CURRENT (µA)
–30
0
Data Sheet
AD7609
TERMINOLOGY
Integral Nonlinearity
The maximum deviation from a straight line passing through
the endpoints of the ADC transfer function. The endpoints of
the transfer function are zero scale, a ½ LSB below the first code
transition, and full scale at ½ LSB above the last code transition.
Differential Nonlinearity
The difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Bipolar Zero Code Error
The deviation of the midscale transition (all 1s to all 0s) from
the ideal VIN voltage, that is, AGND.
Bipolar Zero Code Error Match
The difference in bipolar zero code error between any two input
channels.
Positive Full-Scale Error
The last transition (from 011 . . . 10 to 011 . . . 11 in twos
complement coding) should occur for an analog voltage 1½
LSB below the nominal full scale (9.99977 V for the ±10 V
range and 4.99988 V for the ±5 V range). The positive full-scale
error is the deviation of the actual level of the last transition
from the ideal level.
Positive Full-Scale Error Match
The difference in positive full-scale error between any two input
channels.
Negative Full-Scale Error
The first transition (from 100 . . . 00 to 100 . . . 01 in twos
complement coding) should occur for an analog voltage ½ LSB
above the negative full scale (−9.999923 V for the ±10 V range
and −4.9999618 for the ±5 V range). The negative full-scale
error is the deviation of the actual level of the first transition
from the ideal level.
Negative Full-Scale Error Match
The difference in negative full-scale error between any two
input channels.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of the conversion. The track-and-hold acquisition time is the
time required for the output of the track-and-hold amplifier to
reach its final value, within ±1 LSB, after the end of the conversion.
See the Track-and-Hold Amplifiers section for more details.
Signal-to-(Noise + Distortion) Ratio
The measured ratio of signal-to-(noise + distortion) at the
output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals
up to half the sampling frequency (fS/2, excluding dc). The ratio
depends on the number of quantization levels in the digitization
process: the more levels, the smaller the quantization noise. The
theoretical signal-to-(noise + distortion) ratio for an ideal N-bit
converter with a sine wave input is given by
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
Thus, for an 18-bit converter, this is 110.12 dB.
Total Harmonic Distortion (THD)
The ratio of the rms sum of the harmonics to the fundamental.
For the AD7609, it is defined as
THD (dB) =
V2 + V3 + V4 + V5 + V6 + V7 + V8 + V9
2
20log
2
2
2
2
2
2
2
V1
where:
V1 is the rms amplitude of the fundamental.
V2 to V9 are the rms amplitudes of the second through ninth
harmonics.
Peak Harmonic or Spurious Noise
The ratio of the rms value of the next largest component in the
ADC output spectrum (up to fS/2, excluding dc) to the rms value
of the fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, it is
determined by a noise peak.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities creates distortion products
at sum and difference frequencies of mfa ± nfb, where m, n = 0,
1, 2, 3. Intermodulation distortion terms are those for which
neither m nor n is equal to 0. For example, the second-order
terms include (fa + fb) and (fa − fb), and the third-order terms
include (2fa + fb), (2fa − fb), (fa + 2fb), and (fa − 2fb).
The calculation of the intermodulation distortion is per the
THD specification, where it is the ratio of the rms sum of the
individual distortion products to the rms amplitude of the
sum of the fundamentals expressed in decibels (dB).
Rev. A | Page 19 of 36
AD7609
Data Sheet
Power Supply Rejection (PSR)
Variations in power supply affect the full-scale transition but
not the converter’s linearity. Power supply rejection is the
maximum change in full-scale transition point due to a change
in power supply voltage from the nominal value. The power
supply rejection ratio is defined as the ratio of the power in
the ADC output at full-scale frequency, f, to the power of a
200 mV p-p sine wave applied to the ADC VDD and VSS supplies
of Frequency fS.
PSRR (dB) = 10 log (Pf/PfS)
where:
Pf is equal to the power at Frequency f in the ADC output.
PfS is equal to the power at Frequency fS coupled onto the VDD
and VSS supplies.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of crosstalk
between any two channels. It is measured by applying a full-scale,
10 kHz sine wave signal to all unselected input channels and
determining the degree to which the signal attenuates in the
selected channel with a 1 kHz signal.
Common-Mode Rejection Ratio (CMRR)
CMRR is defined as the ratio of the power in the ADC
common-mode input at full-scale frequency, f, to the power in
the output of a full-scale p-p sine wave applied to the commonmode voltage of VINX+ and VINX− of frequency, fS,
CMRR (dB) = 20 log (Pf/PfS)
where:
Pf is equal to the power at Frequency f in the ADC input.
PfS is equal to the power at Frequency fS in the ADC output.
Rev. A | Page 20 of 36
Data Sheet
AD7609
THEORY OF OPERATION
CONVERTER DETAILS
Analog Input Clamp Protection
The AD7609 is a data acquisition system that employs a high
speed, low power, charge redistribution successive approximation analog-to-digital converter (ADC) and allows the
simultaneous sampling of eight true differential analog input
channels. The analog inputs on the AD7609 can accept true
bipolar input signals. The RANGE pin is used to select either
±10 V or ±5 V as the input range. The AD7609 operates from
a single 5 V supply.
Figure 32 shows the analog input structure of the AD7609.
Each AD7609 analog input contains clamp protection circuitry.
Despite a single 5 V supply operation, this analog input clamp
protection allows for an input overvoltage up to ±16.5 V.
The AD7609 can handle true bipolar input voltages. The logic
level on the RANGE pin determines the analog input range of
all analog input channels. If this pin is tied to a logic high, the
analog input range is ±10 V for all channels. If this pin is tied
to a logic low, the analog input range is ±5 V for all channels.
A logic change on this pin has an immediate effect on the
analog input range; however, there is a settling time of 80 µs
typically, in addition to the normal acquisition time requirement.
The recommended practice is to hardwire the RANGE pin
according to the desired input range for the system signals.
During normal operation, the applied analog input voltage should
remain within the analog input range selected via the RANGE
pin. A RESET pulse must be applied to the part to ensure the
analog input channels are configured for the range selected.
When in a power-down mode, it is recommended to tie the
analog inputs together or both analog input pins (Vx+, Vx−) to
GND. As per the Analog Input Clamp Protection section, the
overvoltage clamp protection is recommended for use in
transient overvoltage conditions, and should not remain active
for extended periods. Stressing the analog inputs outside of
these conditions may degrade the Bipolar Zero Code error and
THD performance of the AD7609.
CLAMP
1MΩ
SECONDORDER
LPF
09760-129
Vx–
Figure 32. Analog Input Circuitry
Figure 33 shows the current vs. voltage characteristic of the
clamp circuit. For input voltages up to ±16.5 V, no current flows
in the clamp circuit. For input voltages above ±16.5 V, the
AD7609 clamp circuitry turns on and clamps the analog input
to ±16.5 V. A series resister should be placed on the analog
input channels to limit the current to ±10 mA for input voltages
above ±16.5 V. In an application where there is a series resistance
on an analog input channel, VINx+, a corresponding resistance
is required on the VINx− channel (see Figure 34). If there is no
corresponding resister on the Vx− channel, this results in an
offset error on that channel. It is recommended that the input
overvoltage clamp protection circuitry be used to protect the
AD7609 against transient overvoltage events. It is not recommended to leave the AD7609 in a condition where the clamp
protection circuitry is active (in normal or power-down
conditions) for extended periods because this may degrade the
bipolar zero code error performance of the AD7609.
AV , VDRIVE = 5V
30 T CC
A = 25°C
20
10
0
–10
–20
–30
–40
–50
–20
Analog Input Impedance
The analog input impedance of the AD7609 is 1 MΩ. This is a
fixed input impedance and does not vary with the AD7609 sampling frequency. This high analog input impedance eliminates
the need for a driver amplifier in front of the AD7609 allowing
for direct connection to the source or sensor. With the need for
a driver amplifier eliminated, bipolar supplies can be removed
from the signal chain, which are often a source of noise in a system.
–15
–10
–5
0
5
10
15
20
SOURCE VOLTAGE (V)
Figure 33. Input Protection Clamp Profile
RFB
AD7609
+10V
–10V
+10V
–10V
R
R
VINx+
C
VINx–
CLAMP
CLAMP
1MΩ
1MΩ
RFB
Figure 34. Input Resistance Matching on the Analog Input
Rev. A | Page 21 of 36
09760-033
Analog Input Ranges
CLAMP
09760-031
ANALOG INPUT
Vx+
RFB
INPUT CLAMP CURRENT (mA)
The AD7609 contains input clamp protection, input signal
scaling amplifiers, a second-order antialiasing filter, track-andhold amplifiers, an on-chip reference, reference buffers, a high
speed ADC, a digital filter, and high speed parallel and serial
interfaces. Sampling on the AD7609 is controlled using
CONVST x signals.
RFB
1MΩ
AD7609
Data Sheet
Analog Input Antialiasing Filter
An analog antialiasing filter is also provided on the AD7609.
The filter is a second-order Butterworth. Figure 35 and
Figure 36 show the frequency and phase response respectively
of the analog antialiasing filter. In the ±5 V range, the −3 dB
frequency is typically 23 kHz. In the ±10 V range, the −3 dB
frequency is typically 32 kHz.
0
10V DIFF
–5
5V DIFF
–15
ADC TRANSFER FUNCTION
–20
The output coding of the AD7609 is twos complement. The
designed code transitions occur midway between successive
integer LSB values, that is, 1/2 LSB, 3/2 LSB. The LSB size is
FSR/262,144 for the AD7609. The FSR for the AD7609 is 40 V
for the ±10 V range and 20 V for the ±5 V range. The ideal
transfer characteristic for the AD7609 is shown in Figure 37.
–25
TEMP
–40°C
25°C
85°C
–40°C
5V
25°C
85°C
–30
10V
–35
0.1dB
13,354Hz
12,769Hz
12,427Hz
10,303Hz
9619Hz
9326Hz
–40
100
3dB
33,520Hz
32,397Hz
31,177Hz
24,365Hz
23,389Hz
22,607Hz
1k
10k
FREQUENCY (Hz)
100k
09760-032
ATTENUATION (dB)
–10
The conversion clock for the part is internally generated, and
the conversion time for all channels is 4 µs on the AD7609. The
BUSY signal returns low after all eight conversions to indicate the
end of the conversion process. On the falling edge of BUSY, the
track-and-hold amplifiers return to track mode. New data can
be read from the output register via the parallel, or serial
interface after BUSY goes low; or, alternatively, data from the
previous conversion can be read while BUSY is high. Reading data
from the AD7609 while a conversion is in progress has little
effect on performance and allows a faster throughput to be
achieved. With a VDRIVE > 3.3 V, the SNR is reduced by ~1.5 dB
when reading during a conversion.
V+ ± (V–)
× 131,072 ×
10V
V+ ± (V–)
±5V CODE =
× 131,072 ×
5V
±10V CODE =
Figure 35. Analog Antialiasing Filter Frequency Response
REF
2.5V
REF
2.5V
14
13
011...111
011...110
12
ADC CODE
±5V RANGE
9
8
000...001
000...000
111...111
LSB =
+FSR – (–FSR)
218
100...010
100...001
100...000
6
5
–FS + 1/2LSB
0V – 1LSB +FS – 3/2LSB
4
ANALOG INPUT
3
Figure 37. AD7609 Transfer Characteristic
AVCC, VDRIVE = 5V
fSAMPLE = 200kSPS
TA = 25°C
2
1
0
10
1k
10k
INPUT FREQUENCY (Hz)
100k
Figure 36. Analog Antialiasing Filter Phase Response
The LSB size is dependent on the analog input range selected
(see Table 7).
Table 7. Output Codes and Ideal Input Values
Track-and-Hold Amplifiers
The track-and-hold amplifiers on the AD7609 allow the ADC to
accurately acquire an input sine wave of full-scale amplitude
to 18-bit resolution. The track-and-hold amplifiers sample
their respective inputs simultaneously on the rising edge of
CONVST x. The aperture time for track-and-hold (that is, the
delay time between the external CONVST x signal and the
track-and-hold actually going into hold) is well matched, by design,
across all eight track-and-holds on one device and from device
to device. This matching allows more than one AD7609 device
to be sampled simultaneously in a system.
09760-034
±10V RANGE
7
09760-133
PHASE DELAY (µs)
11
10
Description
FSR − 0.5 LSB
Midscale + 1 LSB
Midscale
Midscale – 1 LSB
−FSR + 1 LSB
−FSR
The end of the conversion process across all eight channels is
indicated by the falling edge of BUSY; and it is at this point that the
track-and-holds return to track mode and the acquisition time
for the next set of conversions begins.
Rev. A | Page 22 of 36
Analog Input
(V+ − (V−)
10 V Range
+19.99992 V
+152.58 µV
0V
−152.58 µV
−19.99984 V
−20 V
Analog
Input
V+ − (V−)
5 V Range
9.999961 V
76 µV
0V
−76 µV
−9.99992 V
−10 V
Digital
Output
Code (Hex)
0x1FFFF
0x00001
0x00000
0x3FFFF
0x20001
0x20000
Data Sheet
AD7609
INTERNAL/EXTERNAL REFERENCE
REFIN/REFOUT
SAR
The AD7609 contains an on-chip 2.5 V band gap reference. The
REFIN/REFOUT pin allows access to the 2.5 V reference that
generates the on-chip 4.5 V reference internally, or it allows an
external reference of 2.5 V to be applied to the AD7609. An
externally applied reference of 2.5 V is also amplified to 4.5 V using
the internal buffer. This 4.5 V buffered reference is the reference
used by the SAR ADC.
10µF
REFCAPA
09760-035
2.5V
REF
Figure 38. Reference Circuitry
The REF SELECT pin is a logic input pin that allows the user to
select between the internal reference and the external reference.
If this pin is set to logic high, the internal reference is selected
and is enabled; if this pin is set to logic low, the internal reference is disabled and an external reference voltage must be
applied to the REFIN/REFOUT pin. The internal reference
buffer is always enabled. After a reset, the AD7609 operates in
the reference mode selected by the REF SELECT pin. Decoupling
is required on the REFIN/REFOUT pin for both the internal
or external reference options. A 10 µF ceramic capacitor is
required on the REFIN/REFOUT to ground close to the
REFGND pins. The AD7609 contains a reference buffer
configured to amplify the REF voltage up to ~4.5 V, as shown
in Figure 38. The REFCAPA and REFCAPB pins must be
shorted together externally and a ceramic capacitor of 10 μF
applied to REFGND to ensure the reference buffer is in
closed-loop operation. The reference voltage available at the
REFIN/REFOUT pin is 2.5 V.
VDRIVE
AD7609
AD7609
REF SELECT
REF SELECT
REF SELECT
REFIN/REFOUT
REFIN/REFOUT
REFIN/REFOUT
+
10µF
100nF
100nF
09760-036
AD7609
Figure 39. Single External Reference Driving Multiple AD7609
REFIN/REFOUT Pins
AD7609
AD7609
AD7609
REF SELECT
REF SELECT
REF SELECT
REFIN/REFOUT
REFIN/REFOUT
REFIN/REFOUT
100nF
100nF
100nF
ADR421
External Reference Mode
One ADR421 external reference can be used to drive the
REFIN/REFOUT pins of all AD7609 devices (see Figure 39). In
this configuration, each AD7609 REFIN/REFOUT pin should
be decoupled with a 100 nF decoupling capacitor.
Internal Reference Mode
One AD7609 device, configured to operate in the internal
reference mode, can be used to drive the remaining AD7609
devices, which are configured to operate in external reference
mode (see Figure 40). The REFIN/REFOUT pin of the AD7609,
configured in internal reference mode, should be decoupled
using a 10 µF ceramic decoupling capacitor. The other AD7609
devices, configured in external reference mode, should use a
100 nF decoupling capacitor on their REFIN/REFOUT pins.
Rev. A | Page 23 of 36
0.1µF
Figure 40. Internal Reference Driving Multiple AD7609 REFIN Pins
09760-037
When the AD7609 is configured in external reference mode,
the REFIN/REFOUT pin is a high input impedance pin. For
applications using multiple AD7609 devices, the following
configurations are recommended depending on the application
requirements.
REFCAPB
BUF
AD7609
Data Sheet
TYPICAL CONNECTION DIAGRAM
POWER-DOWN MODES
Figure 41 shows the typical connection diagram for the
AD7609. There are four AVCC supply pins on the part that
can be tied together and decoupled using a 100 nF capacitor at
each supply pin and a 10 µF capacitor at the supply source. The
AD7609 can operate with the internal reference or an externally
applied reference. In this configuration, the AD7609 is configured to operate with the internal reference. When using a single
AD7609 device on the board, the REFIN/REFOUT pin should
be decoupled with a 10 µF capacitor. In an application with
multiple AD7609 devices, see the Internal/External Reference
section. The REFCAPA and REFCAPB pins are shorted together
and decoupled with a 10 µF ceramic capacitor.
There are two power-down modes available on the AD7609.
The STBY pin controls whether the AD7609 is in normal mode
or one of the two power-down modes. The two power-down
modes available are standby mode and shutdown mode. The
power-down mode is selected through the state of the RANGE
pin when the STBY pin is low. Table 8 shows the configurations
required to choose the desired power-down mode. When the
AD7609 is placed in standby mode, the current consumption is
8 mA maximum and power-up time is approximately 100 µs
because the capacitor on the REFCAPA/REFCAPB pins must
charge up. In standby mode, the on-chip reference and
regulators remain powered up and the amplifiers and ADC core
are powered down. When the AD7609 is placed in shutdown
mode, the current consumption is 11 µA maximum and power
up time is about 13 ms. In shutdown mode, all circuitry
is powered down. When the AD7609 is powered up from
shutdown mode, a reset signal must be applied to the AD7609
after the required power-up time has elapsed.
The VDRIVE supply is connected to the same supply as the processor. The voltage on VDRIVE controls the voltage value of the
output logic signals. For layout, decoupling, and grounding
hints, see the Layout Guidelines section.
After supplies are applied to the AD7609, a reset should be
applied to the AD7609 to ensure that it is configured for the
correct mode of operation.
Table 8. Power-Down Mode Selection
STBY
Power-Down Mode
Standby
Shutdown
ANALOG SUPPLY
VOLTAGE 5V1
1µF
REFIN/REFOUT
100nF
100nF
REGCAP2
AVCC
VDRIVE
REFCAPA
10µF
DB0 TO DB15
+
REFCAPB
REFGND
EIGHT DIFFERENTIAL
ANALOG INPUT PAIRS
V1+
V1–
V2+
V2–
V3+
V3–
V4+
V4–
V5+
V5–
V6+
V6–
V7+
V7–
V8+
V8–
AD7609
CONVST A, B
CS
RD
BUSY
RESET
OS 2
OS 1
OS 0
REF SELECT
PARALLEL
INTERFACE
OVERSAMPLING
VDRIVE
PAR/SER SEL
RANGE
STBY
VDRIVE
AGND
1DECOUPLING SHOWN ON THE AV
CC PIN APPLIES TO EACH AVCC PIN (PIN 1, PIN 37, PIN 38, PIN 48).
DECOUPLING CAPACITOR CAN BE SHARED BETWEEN AV CC PIN 37 AND PIN 38.
2DECOUPLING SHOWN ON THE REGCAP PIN APPLIES TO EACH REGCAP PIN (PIN 36, PIN 39).
Figure 41. Typical Connection Diagram
Rev. A | Page 24 of 36
09760-038
+
DIGITAL SUPPLY
VOLTAGE +2.3V TO +5V
MICROPROCESSOR/
MICROCONVERTER/
DSP
10µF
0
0
RANGE
1
0
Data Sheet
AD7609
Simultaneously Sampling Two Sets of Channels
CONVERSION CONTROL
The AD7609 also allows the analog input channels to be
sampled simultaneously in two sets. This can be used in power
line protection and measurement systems to compensate for
phase differences between PT and CT transformers. In a 50 Hz
system, this allows for up to 9° of phase compensation, and in a
60 Hz system, it allows for up to 10° of phase compensation.
Simultaneous Sampling on All Analog Input Channels
The AD7609 allows simultaneous sampling of all analog input
channels. All channels are sampled simultaneously when both
CONVST x pins (CONVST A, CONVST B) are tied together. A
single CONVST x signal is used to control both CONVST x inputs.
The rising edge of this common CONVST x signal initiates
simultaneous sampling on all analog input channels.
This is accomplished by pulsing the two CONVST x pins independently and is only possible if oversampling is not in use.
CONVST A is used to initiate simultaneous sampling of the first
set of channels (V1 to V4). CONVST B is used to initiate
simultaneous sampling on the second set of analog input
channels (V5 to V8), as illustrated in Figure 42. On the rising
edge of CONVST A, the track-and-hold amplifiers for the first
set of channels are placed into hold mode. On the rising edge
of CONVST B, the track-and-hold amplifiers for the second set
of channels are placed into hold mode. The conversion process
begins after both rising edges of CONVST x have occurred;
therefore, BUSY goes high on the rising edge of the later
CONVST x signal. The falling edge of BUSY also indicates that
the new data can now be read from the parallel bus or the serial
data lines, DOUTA and DOUTB. There is no change to the data
read process when using two separate CONVST x signals.
The AD7609 contains an on-chip oscillator that is used to
perform the conversions. The conversion time for all ADC
channels is tCONV. The BUSY signal indicates to the user when
conversions are in progress, so that when the rising edge of
CONVST x is applied, BUSY goes logic high and transitions low
at the end of the entire conversion process. The falling edge of
the BUSY signal is used to place all eight track-and-hold
amplifiers back into track mode. The falling edge of BUSY also
indicates that the new data can now be read from the parallel
bus (DB[15:0]) or the serial data lines, DOUTA and DOUTB.
Connect all unused analog input channel to AGND. The results
for any unused channels are still included in the data read
because all channels are always converted.
V1 TO V4 TRACK-AND-HOLD
ENTER HOLD
V5 TO V8 TRACK-AND-HOLD
ENTER HOLD
CONVST A
t5
CONVST B
AD7609 CONVERTS
ON ALL 8 CHANNELS
BUSY
tCONV
CS, RD
V1
V2
V8
09760-039
DATA: DB[15:0]
FRSTDATA
Figure 42. Simultaneous Sampling on Channel Sets Using Independent CONVST A/CONVST B Signals—Parallel Mode
Rev. A | Page 25 of 36
AD7609
Data Sheet
DIGITAL INTERFACE
The AD7609 provides two interface options: a parallel interface
and a high speed serial interface. The required interface mode is
selected via the PAR/SER SEL pin.
AD7609
INTERRUPT
BUSY 14
The operation of the interface modes is described in the
following sections.
DIGITAL
HOST
DB[15:0] 33:16
PARALLEL INTERFACE (PAR/SER SEL = 0)
Data can be read from the AD7609 via the parallel data bus with
standard CS and RD signals. To read the data over the parallel
bus, the PAR/SER SEL pin should be tied low. The CS and RD
input signals are internally gated to enable the conversion result
onto the data bus. The data lines, DB15 to DB0, leave their high
impedance state when both CS and RD are logic low.
The rising edge of the CS input signal three-states the bus and
the falling edge of the CS input signal takes the bus out of the
high impedance state. CS is the control signal that enables the
data lines; it is the function that allows multiple AD7609
devices to share the same parallel data bus. The CS signal can
be permanently tied low, and the RD signal can be used to
access the conversion results, as shown in Figure 4. A read
operation of new data can take place after the BUSY signal
goes low (Figure 2), or, alternatively, a read operation of data
from the previous conversion process can take place while
BUSY is high (Figure 3).
The RD pin is used to read data from the output conversion
results register. Two RD pulses are required to read the full
18-bit conversion result from each channel. Applying a
sequence of 16 RD pulses to the AD7609 RD pin clocks the
conversion results out from each channel onto the parallel
output bus, DB[15:0], in ascending order. The first RD falling
edge after BUSY goes low clocks out DB[17:2] of the V1 result,
the next RD falling edge updates the bus with DB[1:0] of the V1
result. It takes 16 RD pulses to read the eight 18-bit conversion
results from the AD7609. The 16th falling edge of RD clocks out
the DB[1:0] conversion result for Channel V8. When the RD
signal is logic low, it enables the data conversion result from
each channel to be transferred to the digital host (DSP, FPGA).
When there is only one AD7609 in a system/board and it
does not share the parallel bus, data can be read using only one
control signal from the digital host. The CS and RD signals
can be tied together, as shown in Figure 5. In this case, the data
bus comes out of three-state on the falling edge of CS/RD. The
combined CS and RD signal allows the data to be clocked out
of the AD7609 and to be read by the digital host. In this case,
CS is used to frame the data transfer of each data channel and
16 CS pulses are required to read the eight channels of data.
09760-040
CS 13
RD 12
Figure 43. AD7609 Interface Diagram: One AD7609 Using the Parallel Bus; CS
and RD Shorted Together
SERIAL INTERFACE (PAR/SER SEL = 1)
To read data back from the AD7609 over the serial interface,
the PAR/SER SEL pin should be tied high. The CS and SCLK
signals are used to transfer data from the AD7609. The AD7609
has two serial data output pins, DOUTA and DOUTB. Data can be
read back from the AD7609 using one or both of these DOUT
lines. For the AD7609, conversion results from Channel V1 to
Channel V4 first appear on DOUTA, whereas conversion results
from Channel V5 to Channel V8 first appear on DOUTB.
The CS falling edge takes the data output lines (DOUTA and
DOUTB) out of three-state and clocks out the MSB of the conversion result. The rising edge of SCLK clocks all subsequent data
bits onto the serial data outputs, DOUTA and DOUTB. The CS
input can be held low for the entire serial read or it can be
pulsed to frame each channel read of 18 SCLK cycles.
Figure 44 shows a read of eight simultaneous conversion results
using two DOUT lines on the AD7609. In this case, a 72 SCLK
transfer is used to access data from the AD7609 and CS is held
low to frame the entire 72 SCLK cycles. Data can also be clocked
out using only one DOUT line, in which case DOUTA is recommended to access all conversion data, because the channel data
is output in ascending order. For the AD7609 to access all eight
conversion results on one DOUT line, a total of 144 SCLK cycles
are required. These 144 SCLK cycles can be framed by one CS
signal or each group of 18 SCLK cycles can be individually
framed by the CS signal. The disadvantage of using only one
DOUT line is that the throughput rate is reduced if reading after
conversion. The unused DOUT line should be left unconnected
in serial mode. For the AD7609, if DOUTB is to be used as a
single DOUT line, the channel results are output in the following
order: V5, V6, V7, V8, V1, V2, V3, V4; however, the FRSTDATA
indicator returns low after V5 is read on DOUTB.
Rev. A | Page 26 of 36
Data Sheet
AD7609
Figure 6 shows the timing diagram for reading one channel of
data, framed by the CS signal, from the AD7609 in serial mode.
The SCLK input signal provides the clock source for the serial
read operation. CS goes low to access the data from the AD7609.
The falling edge of CS takes the bus out of three-state and
clocks out the MSB of the 18-bit conversion result. This MSB
is valid on the first falling edge of the SCLK after the CS falling
edge. The subsequent 17 data bits are clocked out of the
AD7609 on the SCLK rising edge. Data is valid on the SCLK
falling edge. Eighteen clock cycles must be provided to the
AD7609 to access each conversion result.
The FRSTDATA output signal indicates when the first channel,
V1, is being read back. When the CS input is high, the FRSTDATA
output pin is in three-state. In serial mode, the falling edge of
CS takes FRSTDATA out of three-state and sets the FRSTDATA
pin high indicating that the result from V1 is available on the
DOUTA output data line. The FRSTDATA output returns to a
logic low following the 18th SCLK falling edge. If all channels
are read on DOUTB, the FRSTDATA output does not go high
when V1 is being output on this serial data output pin. It only
goes high when V1 is available on DOUTA (and this is when V5
is available on DOUTB).
READING DURING CONVERSION
Data can be read from the AD7609 while BUSY is high
and conversions are in progress. This has little effect on the
performance of the converter and allows a faster throughput
rate to be achieved. A parallel or serial read can be performed
during conversions and when oversampling may or may not
be in use. Figure 3 shows the timing diagram for reading while
BUSY is high in parallel or serial mode. Reading during conversions allows the full throughput rate to be achieved when using
the serial interface with a VDRIVE of 3.3 V to 5.25 V.
Data can be read from the AD7609 at any time other than on
the falling edge of BUSY because this is when the output data
registers are updated with the new conversion data. t6, outlined
in Table 3, should be observed in this condition.
CS
72
DOUTA
V1
V2
V3
V4
DOUTB
V5
V6
V7
V8
Figure 44. AD7609 Serial Interface with Two DOUT Lines
Rev. A | Page 27 of 36
09760-041
SCLK
AD7609
Data Sheet
DIGITAL FILTER
The AD7609 contains an optional digital filter. This digital filter
is a first-order sinc filter. This digital filter should be used in
applications where slower throughput rates are used or where
higher signal-to-noise ratio or dynamic range is desirable. The
oversampling ratio of the digital filter is controlled using the
oversampling pins, OS [2:0] (see Table 9). OS 2 is the MSB
control bit and OS 0 is the LSB control bit. Table 9 provides
the oversampling bit decoding to select the different oversample
rates. The OS pins are latched on the falling edge of BUSY.
This sets the oversampling rate for the next conversion (see
Figure 45). In addition to the oversampling function, the output
result is decimated to 18-bit resolution.
If the OS pins are set to select an OS ratio of 8, the next
CONVST x rising edge takes the first sample for each channel
and the remaining seven samples for all channels are taken with
an internally generated sampling signal. These samples are then
averaged to yield an improvement in SNR performance. Table 9
shows typical SNR performance for both the ±10 V and the
±5 V ranges. As Table 9 indicates, there is an improvement in
SNR as the OS ratio increases. As the OS ratio increases, the
3 dB frequency is reduced and the allowed sampling frequency
is also reduced. In an application where the required sampling
frequency is 10 kSPS, an OS ratio of up to 16 can be used. In
this case, the application sees an improvement in SNR but the
input −3 dB bandwidth is limited to ~6 kHz.
The CONVST A and CONVST B pins must be tied/driven
together when oversampling is turned on. When the oversampling function is turned on, the BUSY high time for the
conversion process extends. The actual BUSY high time
depends on the oversampling rate selected; the higher the
oversampling rate, the longer the BUSY high, or total
conversion time, see Table 9.
Figure 46 shows that the conversion time extends as the oversampling rate is increased, and the BUSY signal lengthens for the
different oversampling rates. For example, a sampling frequency
of 10 kSPS yields a cycle time of 100 µs. Figure 46 shows OS × 2
and OS × 4; for a 10 kSPS example, there is adequate cycle time
to further increase the oversampling rate and yield greater
improvements in SNR performance. In an application where
the initial sampling or throughput rate is at 200 kSPS, for
example, and oversampling is turned on, the throughput rate
must be reduced to accommodate the longer conversion time
and to allow for the read. To achieve the fastest throughput
rate possible when oversampling is turned on, the read can be
performed during the BUSY high time. The falling edge of BUSY
is used to update the output data registers with the new conversion data; therefore, the reading of conversion data should not
occur on this edge. Figure 47 to Figure 53 illustrate the effect of
oversampling on the code spread in a dc histogram plot. As the
oversample rate is increased, the spread of codes is reduced. (In
Figure 47 to Figure 53, AVCC = VDRIVE = 5 V and the sampling
rate was scaled with OS ratio.)
CONVST A,
CONVST B
OVERSAMPLE RATE
LATCHED FOR CONVERSION N + 1
CONVERSION N
CONVERSION N + 1
BUSY
tOS_HOLD
09760-042
tOS_SETUP
OS x
Figure 45. OS Pin Timing
Table 9. Oversampling Bit Decoding (100 Hz Input Signal)
OS
[2:0]
000
001
010
011
100
101
110
111
OS
Ratio
No OS
2
4
8
16
32
64
Invalid
SNR ±5 V Range
(dB)
90.8
93.3
95.5
98
100.6
101.8
102.7
SNR ±10 V Range
(dB)
91.5
93.9
96.4
98.9
101
102
102.9
−3 dB BW 5 V Range
(kHz)
22
22
18.5
11.9
6
3
1.5
Rev. A | Page 28 of 36
−3 dB BW 10 V
Range (kHz)
33
28.9
21.5
12
6
3
1.5
Maximum Throughput
CONVST x Frequency (kHz)
200
100
50
25
12.5
6.25
3.125
Data Sheet
AD7609
tCYCLE
CONVST A,
CONVST B
tCONV
19µs
9µs
4µs
OS = 0
BUSY
OS = 2
OS = 4
t4
t4
t4
CS
09760-043
RD
DATA:
DB[15:0]
Figure 46. AD7609—No Oversampling, Oversampling × 4, and Oversampling × 8 Using Read After Conversion
3000
1600
OVERSAMPLING BY 4
NO OVERSAMPLING
1384 1373
840
800
727
600
492
450
400
1500
1000
2 10 27
–9 –8 –7 –6 –5 –4 –3 –2 –1 0 1
CODE
2
3
4
5
32 11
2
6
8 9
7
1
0
5
49
–5
–4
–3
–2
–1
0
CODE
1
79
8
3
4
2
Figure 49. Histogram of Codes—OS × 4 (10 Codes)
Figure 47. Histogram of Codes—No OS (19 Codes)
4000
2000
OVERSAMPLING BY 2
OVERSAMPLING BY 8
3392
3500
NUMBER OF OCCURRENCES
1600
1389
1400
1146
1200
1000
788
800
599
600
400
3000
2397
2500
2000
1568
1500
1000
317
214
12
46
–7 –6 –5 –4 –3 –2 –1
229
105
0 1
CODE
2
3
4
15
2
1
5
6
7
09760-045
1
549
500
200
0
1
41
–4
–3
15
–2
–1
0
1
2
CODE
Figure 50. Histogram of Codes—OS × 8 (Eight Codes)
Figure 48. Histogram Of Codes—OS × 2 (15 Codes)
Rev. A | Page 29 of 36
3
09760-047
1785 1772
1800
NUMBER OF OCCURRENCES
422
341
100
83
0
1340
1191
500
219
210
200
2000
09760-046
NUMBER OF OCCURRENCES
1062
1000
0
2363 2394
2500
1167
1200
09760-044
NUMBER OF OCCURRENCES
1400
AD7609
Data Sheet
When the oversampling mode is selected, this has the effect
of adding a digital filter function after the ADC. The different
oversampling rates and the CONVST x sampling frequency
produces different digital filter frequency profiles.
4500
OVERSAMPLING BY 16
3833
3500
3279
3000
Figure 54 to Figure 59 show the digital filter frequency profiles
for the different oversampling rates. The combination of the
analog antialiasing filter and the oversampling digital filter can
be used to eliminate or reduce the complexity of the design of
the filter before the AD7609. The digital filtering combines
steep roll-off and linear phase response.
2500
2000
1500
1000
0
657
385
406
500
0
–3
–2
–1
0
1
2
CODE
6000
OVERSAMPLING BY 32
5090
5000
–20
–30
–40
–50
–60
4000
–70
–80
2716
–90
100
2000
1k
10k
100k
1M
10M
FREQUENCY (Hz)
09760-051
3000
Figure 54. Digital Filter Response for OS × 2
1000
341
0
–2
–1
0
1
CODE
09760-049
45
0
–20
ATTENUATION (dB)
Figure 52. Histogram of Codes—OS × 32 (Four Codes)
7000
OVERSAMPLING BY 64
5871
6000
5000
AVCC = 5V
VDRIVE = 5V
TA = 25°C
10V RANGE
OS BY 4
–10
–30
–40
–50
–60
–70
–80
4000
–90
3000
–100
100
2245
2000
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 55. Digital Filter Response for OS × 4
1000
–2
–1
0
1
CODE
09760-050
75
1
0
Figure 53. Histogram of Codes – OS × 64 (Four Codes)
Rev. A | Page 30 of 36
10M
09760-052
NUMBER OF OCCURENCES
–10
ATTENUATION (dB)
Figure 51. Histogram of Codes—OS × 16 (Six Codes)
NUMBER OF OCCURENCES
AVCC = 5V
VDRIVE = 5V
TA = 25°C
10V RANGE
OS BY 2
14
3
09760-048
NUMBER OF OCCURENCES
4000
Data Sheet
AD7609
–20
–20
ATTENUATION (dB)
–30
–40
–50
–60
–70
–30
–40
–50
–60
–70
–80
–80
–90
–90
1k
10k
100k
1M
10M
FREQUENCY (Hz)
–100
100
09760-053
–100
100
–20
ATTENUATION (dB)
–40
–50
–60
–70
–40
–50
–60
–70
–80
–90
–90
10k
100k
1M
FREQUENCY (Hz)
10M
–30
–80
1k
1M
10M
AVCC = 5V
VDRIVE = 5V
TA = 25°C
10V RANGE
OS BY 64
–10
–30
–100
100
100k
0
09760-054
ATTENUATION (dB)
–20
10k
Figure 58. Digital Filter Response for OS × 32
AVCC = 5V
VDRIVE = 5V
TA = 25°C
10V RANGE
OS BY 16
–10
1k
FREQUENCY (Hz)
Figure 56. Digital Filter Response for OS × 8
0
AVCC = 5V
VDRIVE = 5V
TA = 25°C
10V RANGE
OS BY 32
–10
09760-055
–10
ATTENUATION (dB)
0
AVCC = 5V
VDRIVE = 5V
TA = 25°C
10V RANGE
OS BY 8
Figure 57. Digital Filter Response for OS × 16
–100
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 59. Digital Filter Response for OS × 64
Rev. A | Page 31 of 36
10M
09760-056
0
AD7609
Data Sheet
LAYOUT GUIDELINES
The printed circuit board that houses the AD7609 should be
designed so that the analog and digital sections are separated
and confined to different areas of the board.
If the AD7609 is in a system where multiple devices require
analog-to-digital ground connections, the connection should
still be made at only one point, a star ground point, which
should be established as close as possible to the AD7609. Good
connections should be made to the ground plane. Avoid sharing
one connection for multiple ground pins. Individual vias or
multiple vias to the ground plane should be used for each
ground pin.
09760-057
Use at least one ground plane. It can be common or split
between the digital and analog sections. In the case of the split
plane, the digital and analog ground planes should be joined in
only one place, preferably as close as possible to the AD7609.
Figure 60. Top Layer Decoupling REFIN/REFOUT, REFCAPA, REFCAPB, and
REGCAP Pins
The power supply lines to the AVCC and VDRIVE pins on the
AD7609 should use as large a trace as possible to provide low
impedance paths and reduce the effect of glitches on the power
supply lines. Where possible, use supply planes. Good connections should be made between the AD7609 supply pins and the
power tracks on the board; this should involve the use of a single
via or multiple vias for each supply pin.
Good decoupling is also important to lower the supply impedance presented to the AD7609 and to reduce the magnitude of
the supply spikes. Place the decoupling capacitors close to,
ideally right up against, these pins and their corresponding
ground pins. Place the decoupling capacitors for the REFIN/
REFOUT pin and the REFCAPA and REFCAPB pins as close as
possible to their respective AD7609 pins. Where possible, they
should be placed on the same side of the board as the AD7609
device. Figure 60 shows the recommended decoupling on the
top layer of the AD7609 board. Figure 61 shows bottom layer
decoupling. Bottom layer decoupling is for the four AVCC pins
and the VDRIVE pin.
Rev. A | Page 32 of 36
09760-058
Avoid running digital lines under the devices because doing
so couples noise onto the die. Allow the analog ground plane
to run under the AD7609 to avoid noise coupling. Shield fastswitching signals like CONVST A, CONVST B, or clocks with
digital ground to avoid radiating noise to other sections of the
board, and they should never run near analog signal paths.
Avoid crossover of digital and analog signals. Run traces on
layers in close proximity on the board at right angles to each
other to reduce the effect of feedthrough through the board.
Figure 61. Bottom Layer Decoupling
Data Sheet
AD7609
09760-059
To ensure good device-to-device performance matching in a
system that contains multiple AD7609 devices, a symmetrical
layout between the AD7609 devices is important. Figure 62
shows a layout with two AD7609 devices. The AVCC supply
plane runs to the right of both devices. The VDRIVE supply track
runs to the left of the two AD7609 devices. The reference chip
is positioned between both AD7609 devices and the reference
voltage track runs north to Pin 42 of U1 and south to Pin 42
to U2. A solid ground plane is used. These symmetrical layout
principles can be applied to a system that contains more than
two AD7609 devices. The AD7609 devices can be placed in a
north-to-south direction with the reference voltage located
midway between the AD7609 devices and the reference track
running in the north-to-south direction similar to Figure 62.
Figure 62. Multiple AD7609 Layout, Top Layer and Supply Plane Layer
Rev. A | Page 33 of 36
AD7609
Data Sheet
OUTLINE DIMENSIONS
0.75
0.60
0.45
12.20
12.00 SQ
11.80
1.60
MAX
64
49
1
48
PIN 1
10.20
10.00 SQ
9.80
TOP VIEW
(PINS DOWN)
0.15
0.05
0.20
0.09
7°
3.5°
0°
SEATING
PLANE
16
0.08
COPLANARITY
VIEW A
33
32
17
VIEW A
0.50
BSC
LEAD PITCH
0.27
0.22
0.17
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-BCD
051706-A
1.45
1.40
1.35
Figure 63. 64-Lead Low Profile Quad Flat Package [LQFP]
(ST-64-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
AD7609BSTZ
AD7609BSTZ-RL
EVAL-AD7609EDZ
CED1Z
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
64-Lead Low Profile Quad Flat Package [LQFP]
64-Lead Low Profile Quad Flat Package [LQFP]
Evaluation Board for the AD7609
Converter Evaluation Development
Z = RoHS Compliant Part.
Rev. A | Page 34 of 36
Package Option
ST-64-2
ST-64-2
Data Sheet
AD7609
NOTES
Rev. A | Page 35 of 36
AD7609
Data Sheet
NOTES
©2011–2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09760-0-2/12(A)
Rev. A | Page 36 of 36
Similar pages