DTD723YE / DTD723YM Transistors 200mA / 30V Low VCE (sat) Digital transistors (with built-in resistors) DTD723YE / DTD723YM zApplications Inverter, Interface, Driver zExternal dimensions (Unit : mm) DTD723YE (2) 1.6 0.8 (3) 0.2 0.15 0.5 0.5 EMT3 JEITA No. (SC-75A) JEDEC No. <SOT-416> 0.1Min. (1) 0.2 (1) GND (2) IN (3) OUT 1.0 Each lead has same dimensions Abbreviated symbol : M62 1.2 0.32 0.2 DTD723YM 0.8 1.2 (3) (1)(2) 0.4 0.4 zStructure NPN epitaxial plannar silicon transistor (Resistor built-in type) 0.2 0.22 (1) IN (2) GND (3) OUT 0.13 0.5 0.8 VMT3 Each lead has same dimensions Abbreviated symbol : M62 zAbsolute maximum ratings (Ta=25°C) zPackaging specifications Limits Symbol 0.55 0.3 zFeature 1) VCE (sat) is lower than conventional products. 2) Built-in bias resistors enable the configuration of an inverter circuit without connecting external input resistors (see equivalent circuit). 3) The bias resistors consist of thin-film resistors with complete isolation to allow negative biasing of the input. They also have the advantage of almost completely eliminating parasitic effects. 4) Only the on / off conditions need to be set for operation, making the device design easy. Parameter 0.7 1.6 DTD723YE DTD723YM Unit Package EMT3 VMT3 Packaging type Taping Taping TL T2L 3000 8000 Supply voltage VCC 30 V Code Input voltage VIN −5 to +15 V Basic ordering unit (pieces) Collector current ∗1 IC (max) 200 mA Part No. Power dissipation ∗2 PD 150 mW DTD723YE Junction temperature Tj 150 C DTD723YM Storage temperature Tstg −55 to +150 C − − ∗1 Characteristics of built-in transistor. ∗2 Each terminal mounted on a recommended land. zElectrical characteristics (Ta=25°C) Parameter Symbol zEquivalent circuit Min. Typ. Max. Unit Conditions VI(off) − − 0.3 VI(on) 2.5 − − VO(on) − 70 300 mV IO/II= 50mA / 2.5mA II − − 3.0 mA VI= 5V IO(off) − − 500 nA VCC= 30V, VI=0V DC current gain GI 140 − − − Transition frequency ∗ fT − 260 − MHz VCE= 10V, IE= −5mA, f=100MHz Input resistance R1 1.54 2.2 2.86 kΩ − Resistance ratio R2/R1 3.6 4.5 5.5 − − Input voltage Output voltage Input current Output current ∗ Characteristics of built-in transistor. V VCC= 5V, IO= 100µA VO= 0.3V, IO= 20mA OUT R1 IN R2 GND VO= 2V, IO= 100mA OUT IN GND R1=2.2kΩ / R2=10kΩ 1/1 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1