AKM AK4252 Output coupling capacitor-less video amp with lpf Datasheet

[AK4252]
AK4252
Output Coupling Capacitor-less Video Amp with LPF
GENERAL DESCRIPTION
The AK4252 is a Video Amp with LPF. The output coupling capacitor can be removed because the
AK4252 includes the negative power supply circuit. The AK4252 is housed in a space-saving 8-pin
USON package.
FEATURE
1. Video Function
• A Composite Video Input
• A Video-Amp (+12dB) for Composite Video Signal
• Low Pass Filter
• Charge pump circuit for negative power supply
2. Ta = -40 ∼ 85 °C
3. Power Supply: 2.7 ∼ 3.6V (typ. 3.0V)
4. Power Supply Current: 10 mA
5. Package: 8 pin USON
■ Block Diagram
PDN
VIN
Clamp
VOUT
LPF
Clock
Generator
VDD
Charge
Pump
CP
CN
VSS
VEE
Figure 1. AK4252 Block Diagram
MS1091-E-01
2010/04
-1-
[AK4252]
■ Ordering Guide
AK4252VU
AKD4252
−40 ∼ +85°C
8 pin USON (0.5mm pitch)
Evaluation board for AK4252
■ Pin Layout
CP
1
VDD
2
VIN
3
PDN
4
Top
View
MS1091-E-01
8
CN
7
VEE
6
VSS
5
VOUT
2010/04
-2-
[AK4252]
PIN/FUNCTION
No.
Pin Name
CP
I/O
O
1
2
3
VDD
VIN
I
4
PDN
I
5
6
7
8
VOUT
VSS
VEE
CN
O
O
I
Function
Positive Charge Pump Capacitor Terminal Pin
Power Supply Pin.
Composite Video Signal Input Pin
Power-Down Mode Pin. Internal Pull Down 100kΩ.
“H”: Power up, “L”: Power down.
Composite Video Signal Driver Pin
Ground Pin
Negative Voltage Output Pin for Video Amplifier
Negative Charge Pump Capacitor Terminal Pin
ABSOLUTE MAXIMUM RATINGS
(VSS=0V; Note 1)
Parameter
Power Supplies
Input Current, Any Pin Except Supplies
Input Voltage
(Note 2)
Ambient Temperature (powered applied)
Storage Temperature
Symbol
VDD
IIN
VIN
Ta
Tstg
min
−0.3
−0.3
−40
−65
max
4.0
±10
(VDD+0.3) or 4.0
85
150
Units
V
mA
V
°C
°C
Note 1. All voltages are with respect to ground.
Note 2. VIN, PDIN pins. Max value is smaller value between (VDD+0.3)V and 4.0V. The VOUT pin becomes Hi-Z at
the PDN pin = “L”. Therefore the VOUT pin is available to signal line from another device by Wired-OR. The
input signal to the VOUT pin must not exceed this input voltage range. Any voltage must not be applied to the CN
pin.
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS
(VSS=0V; Note 1)
Parameter
Power Supplies
Symbol
VDD
min
2.7
typ
3.0
max
3.6
Units
V
Note 1. All voltages with respect to ground.
* AKM assumes no responsibility for the usage beyond the conditions in this datasheet.
MS1091-E-01
2010/04
-3-
[AK4252]
ANALOG CHRACTERISTICS
(Ta=25°C; VDD=3.0V; VSS = 0V; unless otherwise specified)
Parameter
Conditions
min
typ
max
Units
V Input Characteristics
Input Voltage
0.75
Vpp
Input Sync Chip Clamp Voltage (Note 3)
-0.193 -0.143 -0.093
V
V Output Characteristics (Note 4)
Output Gain
VIN=100kHz, 0.2Vpp
11.0
12.0
13.0
dB
Maximum output voltage
VIN=100kHz , THD=-30dB
2.52
Vpp
65
dB
S/N
BW=100kH ∼ 6MHz, (Note 5)
Secondary Distortion
VIN=3.58MHz, 0.2Vpp (Sin Wave)
-45
dB
Load Resistance
140
150
Ω
15
pF
Load Capacitance
C1 (Figure 2)
400
pF
C2 (Figure 2)
LPF
Frequency Response
Response at 6.75MHz
-3
-0.5
dB
Input= 0.2Vpp, Sin Wave
Response at 27MHz
-40
-20
dB
(0dB at 100kHz)
Group Delay
|GD3MHz - GD6MHz|
10
100
nsec
Power Supplies
Power Up
Black signal is output and no load
10
15
mA
resistance.
Power Down
PDN pin = 0V
1
2
μA
Note 3. The Charge Pump circuit will not work well, if the sync chip clamp voltage input to the VIN pin is not within this
voltage range. This sync chip clamp voltage is the voltage from the pedestal voltage
Note 4. The measurement point is the point A in Figure 2
Note 5. The reference signal is the 100% white signal.
Measurement Point A
75 ohm
Video Signal Output
R2
75 ohm
R1
C1
C2
Figure 2. Load Capacitance C1 and C2
DC CHRACTERISTICS
(Ta=25°C; VDD=2.7 ∼ 3.6V)
Parameter
High-Level Input Voltage
Low-Level Input Voltage
(PDN pin)
(PDN pin)
Symbol
VIH
VIL
MS1091-E-01
min
1.5
-
typ
-
max
0.6
Units
V
V
2010/04
-4-
[AK4252]
■ Video Block
The Video Amp has drivability for a load resistance of 150Ω. The AK4252 has a composite input and output and includes
a low pass filter (LPF). Internal negative power supply circuit supplies negative voltage to the video amp and video amp
0V output is used for a pedestal level. Therefore, the output coupling capacitor can be removed.
AK4252
VDD
Charge
Pump
CP
CN
Negative Power
VSS
1uF
VEE
C2
(+)
C1
1uF
(+)
Note 6. C1 and C2 capacitors should have the low ESR (Equivalent Series Resistance) over all temperature range. When
these capacitors have the polarity, the positive polarity pin should be connected to the CP pin and the VSS pin.
Non polarity capacitors can also be used.
Figure 3. Negative Power Supply circuit
AK4252
75Ω
VOUT
75Ω
0V
Figure 4. Video signal output
■ Power Down Control
When the PDN pin is “L”, the AK4252 is forced to Power Down Mode (Power consumption: typ 1μA). The VOUT pin
becomes Hi-Z at the PDN pin = “L”. The AK4252 includes a power-on-reset function. Therefore any external reset is not
required.
MS1091-E-01
2010/04
-5-
[AK4252]
SYSTEM DESIGN
Figure 5 shows the system connection diagram for the AK4252. An evaluation board [AKD4252] is available which
demonstrates the optimum layout, power supply arrangements and measurement results.
(+)
Power Supply
2.7∼3.6V
10µ
+
1µ
1 CP
0.1µ
CN 8
0.1u
1µ
VEE 7
2 VDD
(+)
Top View VSS 6
3 VIN
75
VOUT 5
4 PDN
DSP or μP
Figure 5. Typical Connection Diagram
Note:
- Any voltage must not be applied to the CN pin.
MS1091-E-01
2010/04
-6-
[AK4252]
PACKAGE
8pin USON (Unit: mm)
2.2 ± 0.05
0.25 ± 0.05
1.2 ± 0.05
2.2 ± 0.05
1.9 ± 0.05
0.05
0.5
M
0.2 ± 0.05
0.6MAX
We recommend mounting this portion onto circuit
board in order to secure mounting intensity. Please do
not connect to a Power Supply, GND, Signal Line, etc.
0.05
■ Material & Lead finish
Package molding compound:
Lead frame material:
Lead frame surface treatment:
Epoxy, Halogen (bromine and chlorine) free
Ni
Au plate
MS1091-E-01
2010/04
-7-
[AK4252]
MARKING
■ AK4252VU
252
XXX
1
XXX: Date code (3 digit)
REVISION HISTORY
Date (YY/MM/DD)
09/06/10
10/04/08
Revision
00
03
Reason
First Edition
Error Correct
Page
Contents
7
■ Material & Lead finish
Lead frame surface treatment: Ag plate → Au plate
IMPORTANT NOTICE
z These products and their specifications are subject to change without notice.
When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei
Microdevices Corporation (AKM) or authorized distributors as to current status of the products.
z AKM assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use
of any information contained herein.
z Any export of these products, or devices or systems containing them, may require an export license or other official
approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange,
or strategic materials.
z AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or
other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use
approved with the express written consent by Representative Director of AKM. As used here:
Note1) A critical component is one whose failure to function or perform may reasonably be expected to result,
whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and
which must therefore meet very high standards of performance and reliability.
Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety
or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or
perform may reasonably be expected to result in loss of life or in significant injury or damage to person or
property.
z It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise
places the product with a third party, to notify such third party in advance of the above content and conditions, and
the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from
any and all claims arising from the use of said product in the absence of such notification.
MS1091-E-01
2010/04
-8-
Similar pages