AD ADM2490EBRWZ High speed, esd-protected, full-duplex, icoupler, isolated rs-485 transceiver Datasheet

High Speed, ESD-Protected, Full-Duplex,
iCoupler®, Isolated RS-485 Transceiver
ADM2490E
FEATURES
APPLICATIONS
Isolated RS-485/RS-422 interfaces
Industrial field networks
INTERBUS
Multipoint data transmission systems
FUNCTIONAL BLOCK DIAGRAM
VDD2
VDD1
ADM2490E
Y
GALVANIC ISOLATION
TxD
RxD
GND1
Z
A
B
GND2
05889-001
Isolated, full-duplex RS-485/RS-422 transceiver
±8 kV ESD protection on RS-485 input/output pins
16 Mbps data rate
Complies with ANSI TIA/EIA RS-485-A-1998 and
ISO 8482: 1987(E)
Suitable for 5 V or 3 V operation (VDD1)
High common-mode transient immunity: >25 kV/μs
Receiver has open-circuit, fail-safe design
32 nodes on the bus
Thermal shutdown protection
Safety and regulatory approvals pending
UL recognition: 5000 V rms isolation voltage
for 1 minute per UL 1577
VDE certificate of conformity
DIN EN 60747-5-2 (VDE 0884 Part 2): 2003-01
DIN EN 60950 (VDE 0805): 2001-12; EN 60950: 2000
VIORM = 848 VPEAK
Operating temperature range: −40°C to +105°C
Wide-body, 16-lead SOIC package
Figure 1.
GENERAL DESCRIPTION
The ADM2490E is an isolated data transceiver with ±8 kV ESD
protection and is suitable for high speed, full-duplex
communication on multipoint transmission lines. It is designed
for balanced transmission lines and complies with ANSI
TIA/EIA RS-485-A-1998 and ISO 8482: 1987(E). The device
employs Analog Devices, Inc., iCoupler technology to combine
a 2-channel isolator, a 3-state differential line driver, and a
differential input receiver into a single package.
The differential transmitter outputs and receiver inputs feature
electrostatic discharge circuitry that provides protection to
±8 kV using the human body model (HBM). The logic side of
the device can be powered with either a 5 V or a 3 V supply,
whereas the bus side requires an isolated 5 V supply.
The device has current-limiting and thermal shutdown features
to protect against output short circuits and situations where bus
contention could cause excessive power dissipation.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
ADM2490E
TABLE OF CONTENTS
Features .............................................................................................. 1
Test Circuits........................................................................................9
Applications....................................................................................... 1
Switching Characteristics .............................................................. 10
Functional Block Diagram .............................................................. 1
Typical Performance Characteristics ........................................... 11
General Description ......................................................................... 1
Circuit Description......................................................................... 13
Revision History ............................................................................... 2
Electrical Isolation...................................................................... 13
Specifications..................................................................................... 3
Truth Tables................................................................................. 13
Timing Specifications .................................................................. 4
Thermal Shutdown .................................................................... 14
ADM2490E Characteristics............................................................. 5
Fail-Safe Receiver Inputs ........................................................... 14
Package Characteristics ............................................................... 5
Magnetic Field Immunity.......................................................... 14
Regulatory Information (Pending) ............................................ 5
Applications Information .............................................................. 15
Insulation and Safety-Related Specifications............................ 5
Isolated Power-Supply Circuit .................................................. 15
VDE 0884 Insulation Characteristics (Pending)...................... 6
PC Board Layout ........................................................................ 15
Absolute Maximum Ratings............................................................ 7
Outline Dimensions ....................................................................... 16
ESD Caution.................................................................................. 7
Ordering Guide .......................................................................... 16
Pin Configuration and Functional Descriptions.......................... 8
REVISION HISTORY
10/06—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
ADM2490E
SPECIFICATIONS
All voltages are relative to their respective ground; 2.7 ≤ VDD1 ≤ 5.5 V, 4.5 V ≤ VDD2 ≤ 5.5 V. All minimum/maximum specifications apply
over the entire recommended operation range, unless otherwise noted. All typical specifications are at TA = 25°C, VDD1 = VDD2 = 5.0 V,
unless otherwise noted.
Table 1.
Parameter
SUPPLY CURRENT
Power-Supply Current, Logic Side
Symbol
TxD/RxD Data Rate < 2 Mbps
TxD/RxD Data Rate = 16 Mbps
Power-Supply Current, Bus Side
TxD/RxD Data Rate < 2 Mbps
TxD/RxD Data Rate = 16 Mbps
DRIVER
Differential Outputs
Differential Output Voltage, Loaded
Max
Unit
Test Conditions
IDD1
IDD1
3.0
6
mA
mA
2.7 V ≤ VDD1 ≤ 5.5 V, unloaded
100 Ω load between Y and Z
IDD2
IDD2
4.0
60
mA
mA
2.7 V ≤ VDD1 ≤ 5.5 V, unloaded
100 Ω load between Y and Z
2.0
5.0
V
1.5
5.0
V
1.5
5.0
V
RL = 50 Ω (RS-422),
see Figure 3
RL = 27 Ω (RS-485),
see Figure 3
−7 V ≤ VTEST1 ≤ +12 V,
see Figure 4
RL = 54 Ω or 100 Ω,
see Figure 3
RL = 54 Ω or 100 Ω,
see Figure 3
RL = 54 Ω or 100 Ω,
see Figure 3
|VOD2|
|VOD4|
Typ
∆|VOD| for Complementary Output States
∆|VOD|
0.2
V
Common-Mode Output Voltage
VOC
3.0
V
∆|VOC| for Complementary Output States
∆|VOC|
0.2
V
IOS
200
mA
0.7 × VDD1
+10
V
V
μA
Short-Circuit Output Current
Logic Inputs
Input Threshold Low
Input Threshold High
TxD Input Current
RECEIVER
Differential Inputs
Differential Input Threshold Voltage
Input Voltage Hysteresis
Input Current (A, B)
Line Input Resistance
Logic Outputs
Output Voltage Low
Output Voltage High
Short Circuit Current
COMMON-MODE TRANSIENT IMMUNITY 1
1
Min
VILTxD
VIHTRxD
ITxD
VTH
VHYS
II
0.25 × VDD1
−10
+0.01
−0.2
+0.2
70
1.0
RIN
−0.8
12
VOLRxD
VOHRxD
VDD1 − 0.3
0.2
VDD1 − 0.2
0.4
100
25
V
mV
mA
mA
kΩ
V
V
mA
kV/μs
VOC = 0 V
VOC = 12 V
VOC = −7 V
IORxD = 1.5 mA, VA − VB = −0.2 V
IORxD = −1.5 mA, VA − VB = 0.2 V
VCM = 1 kV, transient
magnitude = 800 V
CM is the maximum common-mode voltage slew rate that can be sustained while maintaining specification-compliant operation. VCM is the common-mode potential
difference between the logic and bus sides. The transient magnitude is the range over which the common-mode is slewed. The common-mode voltage slew rates
apply to both rising and falling common-mode voltage edges.
Rev. 0 | Page 3 of 16
ADM2490E
TIMING SPECIFICATIONS
TA = −40°C to +85°C
Table 2.
Parameter
DRIVER
Maximum Data Rate
Propagation Delay
Pulse Width Distortion,
PWD = |tPYLH − tPYHL|, PWD = |tPZLH − tPZHL|
Single-Ended Output Rise/Fall Times
RECEIVER
Propagation Delay
Pulse Width Distortion, PWD = |tPLH − tPHL|
Symbol
Min
Typ
Max
Unit
45
60
Mbps
ns
tPWD, tPWD
7
ns
tR, tF
20
ns
tPLH, tPHL
60
ns
tPWD
10
ns
Typ
Max
Unit
45
60
Mbps
ns
9
ns
tR, tF
27
ns
tPLH, tPHL
60
ns
tPWD
10
ns
16
tPLH, tPHL
Test Conditions
RL = 54 Ω, CL1 = C L2 = 100 pF,
see Figure 6 and Figure 8
RL = 54 Ω, CL1 = CL2 = 100 pF,
see Figure 6 and Figure 8
RL = 54 Ω, CL1 = CL2 = 100 pF,
see Figure 6 and Figure 8
CL = 15 pF, see Figure 7 and Figure
9
CL = 15 pF, see Figure 7 and Figure
9
TA = −40°C to +105°C
Table 3.
Parameter
DRIVER
Maximum Data Rate
Propagation Delay
Pulse Width Distortion,
PWD = |tPYLH − tPYHL|, PWD = |tPZLH − tPZHL|
Single-Ended Output Rise/Fall Time
RECEIVER
Propagation Delay
Pulse Width Distortion, PWD = |tPLH − tPHL|
Symbol
Min
10
tPYLH, tPYHL,
tPZLH, tPZHL
tPWD, tPWD
Rev. 0 | Page 4 of 16
Test Conditions
RL = 54 Ω, CL1 = CL2 = 100 pF,
see Figure 6 and Figure 8
RL = 54 Ω, CL1 = CL2 = 100 pF,
see Figure 6 and Figure 8
RL = 54 Ω, CL1 = CL2 = 100 pF,
see Figure 6 and Figure 8
CL = 15 pF, see Figure 7 and
Figure 9
CL = 15 pF, see Figure 7 and
Figure 9
ADM2490E
ADM2490E CHARACTERISTICS
PACKAGE CHARACTERISTICS
Table 4.
Parameter
Resistance (Input-Output) 1
Capacitance (Input-Output)1
Input Capacitance 2
Input IC Junction-to-Case Thermal Resistance
Symbol
RI-O
CI-O
CI
θJCI
Output IC Junction-to-Case Thermal Resistance
θJCO
1
2
Min
Typ
1012
3
4
33
Max
28
Unit
Ω
pF
pF
°C/W
Test Conditions
f = 1 MHz
Thermocouple located at center
of package underside
°C/W
Device considered a 2-terminal device: Pins 1, 2, 3, 4, 5, 6, 7, and 8 are shorted together and Pins 9, 10, 11, 12, 13, 14, 15, and 16 are shorted together.
Input capacitance is from any input data pin to ground.
REGULATORY INFORMATION (PENDING)
Table 5.
UL
To be recognized under 1577 component recognition program: 1
5000 V rms isolation voltage
1
2
VDE
To be certified according to DIN EN 60747-5-2 (VDE 0884 Part 2): 2003-01: 2
Basic insulation, 848 V peak
Complies with DIN EN 60747-5-2 (VDE 0884 Part 2): 2003-01,
DIN EN 60950 (VDE 0805): 2001-12; EN 60950: 2000, reinforced
insulation, 560 V peak
In accordance with UL1577, each ADM2490E is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (current leakage detection limit = 10 μA).
In accordance with DIN EN 60747-5-2, each ADM2490E is proof tested by applying an insulation test voltage ≥ 1590 V peak for 1 second (partial discharge detection
limit = 5 pC).
INSULATION AND SAFETY-RELATED SPECIFICATIONS
Table 6.
Parameter
Rated Dielectric Insulation Voltage
Minimum External Air Gap (Clearance)
Symbol
L(I01)
Value
5000
7.45
Unit
V rms
mm min
Minimum External Tracking (Creepage)
L(I02)
8.1
mm min
Minimum Internal Gap (Internal Clearance)
Tracking Resistance (Comparative Tracking Index)
Isolation Group
CTI
0.017
>175
IIIa
mm min
V
Rev. 0 | Page 5 of 16
Conditions
1-minute duration.
Measured from input terminals to output
terminals, shortest distance through air.
Measured from input terminals to output
terminals, shortest distance along body.
Insulation distance through insulation.
DIN IEC 112/VDE 0303 Part 1.
Material Group (DIN VDE 0110, 1/89).
ADM2490E
VDE 0884 INSULATION CHARACTERISTICS (PENDING)
This isolator is suitable for basic electrical isolation only within the safety limit data. Maintenance of the safety data must be ensured by
means of protective circuits.
An asterisk (*) on a package denotes VDE 0884 approval for 848 V peak working voltage.
Table 7.
Description
Installation Classification per DIN VDE 0110 for Rated Mains Voltage
≤300 V rms
≤450 V rms
≤600 V rms
Climatic Classification
Pollution Degree (DIN VDE 0110, see Table 1)
Maximum Working Insulation Voltage
Input-to-Output Test Voltage, Method b1
VIORM × 1.875 = VPR, 100% Production Tested, tm = 1 sec, Partial Discharge < 5 pC
Input-to-Output Test Voltage, Method a
(After Environmental Tests, Subgroup 1)
VIORM × 1.6 = VPR, tm = 60 sec, Partial Discharge < 5 pC
(After Input and/or Safety Test, Subgroup 2/3)
VIORM × 1.2 = VPR, tm = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage
(Transient Overvoltage, tTR = 10 sec)
Safety-Limiting Values
(Maximum Value Allowed in the Event of a Failure; see Figure 16)
Case Temperature
Input Current
Output Current
Insulation Resistance at TS, VIO = 500 V
Rev. 0 | Page 6 of 16
Symbol
Characteristic
Unit
VIORM
VPR
I to IV
I to II
I to II
40/105/21
2
848
1590
VPEAK
VPEAK
1357
VPEAK
VPR
1018
VPEAK
VTR
6000
VPEAK
TS
IS, INPUT
IS, OUTPUT
RS
150
265
335
>109
°C
mA
mA
Ω
ADM2490E
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted. Each voltage is relative to its
respective ground.
Table 8.
Parameter
Storage Temperature
Ambient Operating Temperature
VDD1
VDD2
Logic Input Voltages
Bus Terminal Voltages
Logic Output Voltages
Average Output Current, per Pin
ESD (Human Body Model) on A, B, Y,
and Z pins
θJA Thermal Impedance
Rating
−55°C to +150°C
−40°C to +105°C
−0.5 V to +7 V
−0.5 V to +6 V
−0.5 V to VDD1 + 0.5 V
−9 V to +14 V
−0.5 V to VDD1 + 0.5 V
±35 mA
±8 kV
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Absolute maximum ratings apply individually only, not in
combination.
ESD CAUTION
73°C/W
Rev. 0 | Page 7 of 16
ADM2490E
PIN CONFIGURATION AND FUNCTIONAL DESCRIPTIONS
VDD1 1
16 VDD2
GND1 2
RxD 3
ADM2490E
13 B
TOP VIEW
GND1 5 (Not to Scale) 12 NC
TxD 6
11 Z
NC 7
GND1 8
10 Y
9
GND2
NC = NO CONNECT
05889-002
NC 4
15 GND2
14 A
Figure 2. ADM2490E Pin Configuration
Table 9. Pin Function Descriptions
Pin No.
1
Mnemonic
VDD1
2, 5, 8
3
4, 7, 12
6
9, 15
16
GND1
RxD
NC
TxD
GND2
VDD2
11
10
13
14
Z
Y
B
A
Description
Power Supply (logic side). Decoupling capacitor to GND1 required; capacitor value should be between
0.01 μF and 0.1 μF.
Ground (logic side).
Receiver Output.
No Connect. These pins must be left floating.
Transmit Data.
Ground (bus side).
Power Supply (bus side). Decoupling capacitor to GND2 required; capacitor value should be between
0.01 μF and 0.1 μF.
Driver Inverting Output.
Driver Noninverting Output.
Receiver Inverting Input.
Receiver Noninverting Input.
Rev. 0 | Page 8 of 16
ADM2490E
TEST CIRCUITS
RL
CL1
Y
VOD
VOC
Z
Figure 3. Driver Voltage Measurement
05889-005
RLDIFF
05889-003
RL
CL2
Figure 6. Driver Propagation Delay
375Ω
A
375Ω
B
Figure 7. Receiver Propagation Delay
Figure 4. Driver Voltage Measurement
VDD2
VDD2
Y
GALVANIC ISOLATION
TxD
RxD
GND1
Z
220Ω
100Ω
220Ω
A
B
GND2
GND2
05889-014
VDD1
VOUT
CL
05889-006
VTEST
60Ω
05889-004
VOD3
Figure 5. Supply-Current Measurement Test Circuit, See Figure 10 and Figure 11
Rev. 0 | Page 9 of 16
ADM2490E
SWITCHING CHARACTERISTICS
3V
1.5V
1.5V
0V
tPLH
tPHL
A, B
Z
0V
Y
tPLH
tPHL
tPWD = |tPLH – tPHL |
VOH
90% POINT
VOH
90% POINT
RO
VOL
10% POINT
tR
tF
10% POINT
1.5V
Figure 8. Driver Propagation Delay, Rise/Fall Timing
Figure 9. Receiver Propagation Delay
Rev. 0 | Page 10 of 16
1.5V
VOL
05889-007
A, B
05889-008
VO
0V
1/2VO
ADM2490E
TYPICAL PERFORMANCE CHARACTERISTICS
3.00
60
2.95
50
tPLH
tPHL
40
30
2.80
20
2.75
10
2.70
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
0
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 13. Receiver Propagation Delay vs. Temperature
Figure 10. IDD1 Supply Current vs. Temperature (See Figure 5)
70
60
TxD
220-100-220 LOAD
1
40
100 LOAD
Y AND Z OUTPUTS
30
2
20
4
–20
0
20
40
60
80
100
TEMPERATURE (°C)
05889-016
0
–40
05889-019
NO LOAD
10
CH1 2V
CH3 2V
Figure 11. IDD2 Supply Current vs. Temperature (See Figure 5)
60
CH2 2V
CH4 2V
M20ns
T
44.2%
A CH2
2.84V
Figure 14. Driver/Receiver Propagation Delay, Low to High
(RLDIFF = 54 Ω, CL1 = CL2 = 100 pF)
TPZHL
TPYLH
TPZLH
TPYHL
50
TxD
40
1
30
Y AND Z OUTPUTS
20
2
10
RxD
0
–40
4
–20
0
20
40
60
80
TEMPERATURE (°C)
100
05889-017
DELAY (ns)
RxD
05889-020
IDD2 (mA)
50
Figure 12. Driver Propagation Delay vs. Temperature
CH1 2V
CH3 2V
CH2 2V
CH4 2V
M20ns
T
44.2%
A CH2
2.84V
Figure 15. Driver/Receiver Propagation Delay, High to Low
(RLDIFF = 54 Ω, CL1 = CL2 = 100 pF)
Rev. 0 | Page 11 of 16
05889-018
2.85
DELAY (ns)
NO LOAD
100 LOAD
220-100-220 LOAD
05889-015
IDD1 (mA)
2.90
ADM2490E
4.77
350
4.76
4.75
4.74
VOLTAGE (V)
250
SIDE 2
200
150
4.68
50
100
150
CASE TEMPERATURE (°C)
4.66
–40
05889-021
0
200
0.30
–4
0.25
VOLTAGE (V)
–2
0.05
4.6
4.8
5.0
VOLTAGE (V)
05889-022
–12
4.4
Figure 17. Output Current vs. Receiver Output High Voltage
14
12
10
8
6
4
0.2
0.4
0.6
0.8
1.0
1.2
VOLTAGE (V)
05889-023
2
0
80
100
0
–40
–20
0
20
40
60
80
100
TEMPERATURE (°C)
Figure 20. Receiver Output Low Voltage vs. Temperature,
IRxD = –4 mA
16
0
60
0.15
0.10
4.2
40
0.20
–10
–14
4.0
20
Figure 19. Receiver Output High Voltage vs. Temperature,
IRxD = −4 mA
0.35
–8
0
TEMPERATURE (°C)
0
–6
–20
Figure 18. Output Current vs. Receiver Output Low Voltage
Rev. 0 | Page 12 of 16
05889-024
4.67
Figure 16. Thermal Derating Curve, Dependence of Safety-Limiting
Values with Case Temperature per VDE 0884
CURRENT (mA)
4.71
4.69
50
CURRENT (mA)
4.72
4.70
SIDE 1
100
0
4.73
05889-025
SAFETY-LIMITING CURRENT (mA)
300
ADM2490E
CIRCUIT DESCRIPTION
ELECTRICAL ISOLATION
TRUTH TABLES
In the ADM2490E, electrical isolation is implemented on the
logic side of the interface. Therefore, the part has two main
sections: a digital isolation section and a transceiver section
(see Figure 21). The driver input signal, which is applied to the
TxD pin and referenced to logic ground (GND1), is coupled
across an isolation barrier to appear at the transceiver section
referenced to isolated ground (GND2). Similarly, the receiver
input, which is referenced to isolated ground in the transceiver
section, is coupled across the isolation barrier to appear at the
RxD pin referenced to logic ground.
The truth tables in this section use the abbreviations shown in
Table 10.
iCoupler Technology
Table 11. Transmitting
The digital signals are transmitted across the isolation barrier
using iCoupler technology. This technique uses chip scale
transformer windings to couple the digital signals magnetically
from one side of the barrier to the other. Digital inputs are
encoded into waveforms that are capable of exciting the
primary transformer winding. At the secondary winding, the
induced waveforms are decoded into the binary value that was
originally transmitted.
Table 10. Truth Table Abbreviations
Abbreviation
H
I
L
X
VDD1
On
On
Description
High level
Indeterminate
Low level
Irrelevant
Supply Status
VDD2
On
On
Input
TxD
H
L
Outputs
Y
Z
H
L
L
H
Table 12. Receiving
Supply Status
VDD1
VDD2
On
On
On
On
On
On
On
On
On
Off
Off
On
Off
Off
VDD1
Inputs
A − B (V)
>0.2
<−0.2
−0.2 < A − B < +0.2
Inputs open
X
X
X
VDD2
ISOLATION
BARRIER
TxD
ENCODE
DECODE
RxD
DECODE
ENCODE
Y
D
Z
R
A
B
GND2
GND1
Figure 21. ADM2490E Digital Isolation and Transceiver Sections
Rev. 0 | Page 13 of 16
05889-009
TRANSCEIVER
DIGITAL ISOLATION
Output
RxD
H
L
I
H
H
H
L
ADM2490E
100
FAIL-SAFE RECEIVER INPUTS
The receiver inputs include a fail-safe feature that guarantees a
logic high on the RxD pin when the A and B inputs are floating
or open-circuited.
10
1
0.1
0.01
0.001
1k
10k
100k
1M
10M
MAGNETIC FIELD FREQUENCY (Hz)
100M
05889-010
The ADM2490E contains thermal-shutdown circuitry that protects
the part from excessive power dissipation during fault conditions.
Shorting the driver outputs to a low impedance source can result in
high driver currents. The thermal sensing circuitry detects the
increase in die temperature under this condition and disables
the driver outputs. This circuitry is designed to disable the driver
outputs when a die temperature of 150°C is reached. As the device
cools, the drivers are re-enabled at a temperature of 140°C.
MAXIMUM ALLOWABLE MAGNETIC
FLUX DENSITY (kGAUSS)
THERMAL SHUTDOWN
Figure 22. Maximum Allowable External Magnetic Flux Density
The limitation on the ac magnetic field immunity of the
iCoupler is set by the condition that induced an error voltage in
the receiving coil (the bottom coil in this case) that was large to
either falsely set or reset the decoder. The voltage induced
across the bottom coil is given by
⎛ − dβ ⎞
2
V =⎜
⎟∑ πrn ; n = 1, 2, . . . , N
⎝ dt ⎠
where, if the pulses at the transformer output are greater than
1.0 V in amplitude:
β = magnetic flux density (gauss).
N = number of turns in receiving coil.
rn = radius of nth turn in receiving coil (cm).
The decoder has a sensing threshold of about 0.5 V; therefore,
there is a 0.5 V margin in which induced voltages can be
tolerated.
Given the geometry of the receiving coil and an imposed
requirement that the induced voltage is, at most, 50% of the
0.5 V margin at the decoder, a maximum allowable magnetic
field is calculated, as shown in Figure 22.
For example, at a magnetic field frequency of 1 MHz, the
maximum allowable magnetic field of 0.2 kGauss induces a
voltage of 0.25 V at the receiving coil. This is about 50% of the
sensing threshold and does not cause a faulty output transition.
Similarly, if such an event occurs during a transmitted pulse and
is the worst-case polarity, it reduces the received pulse from
>1.0 V to 0.75 V—still well above the 0.5 V sensing threshold of
the decoder.
Figure 23 shows the magnetic flux density values in terms of
more familiar quantities, such as maximum allowable current
flow, at given distances away from the ADM2490E transformers.
1000
DISTANCE = 1m
100
DISTANCE = 5mm
10
DISTANCE = 100mm
1
0.1
0.01
1k
10k
100k
1M
10M
MAGNETIC FIELD FREQUENCY (Hz)
100M
05889-011
Because iCouplers use a coreless technology, no magnetic
components are present and the problem of magnetic saturation
of the core material does not exist. Therefore, iCouplers have
essentially infinite dc field immunity. The following analysis
defines the conditions under which this may occur. The 3 V
operating condition of the ADM2409E is examined because it
represents the most susceptible mode of operation.
MAXIMUM ALLOWABLE CURRENT (kA)
MAGNETIC FIELD IMMUNITY
Figure 23. Maximum Allowable Current for
Various Current-to-ADM2490E Spacings
With combinations of strong magnetic field and high frequency,
any loops formed by printed circuit board traces could induce
error voltages large enough to trigger the thresholds of succeeding
circuitry. Care should be taken in the layout of such traces to
avoid this possibility.
Rev. 0 | Page 14 of 16
ADM2490E
APPLICATIONS INFORMATION
The ADM2490E requires isolated power capable of 5 V at up to
approximately 75 mA (this current is dependant on the data
rate and termination resistors used) to be supplied between the
VDD2 and the GND2 pins. A transformer-driver circuit with a
center-tapped transformer and LDO can be used to generate the
isolated 5 V supply, as shown in Figure 25. The center-tapped
transformer provides electrical isolation of the 5 V power
supply. The primary winding of the transformer is excited with
a pair of square waveforms that are 180° out of phase with each
other. A pair of Schottky diodes and a smoothing capacitor are
used to create a rectified signal from the secondary winding.
The ADP667 linear voltage regulator provides a regulated
power supply to the bus-side circuitry (VDD2) of the
ADM2490E.
VDD1
GND1
RxD
NC
GND1
TxD
NC
GND1
ADM2490E
NC = NO CONNECT
Figure 24. Recommended Printed Circuit Board Layout
In applications involving high common-mode transients, care
should be taken to ensure that board coupling across the isolation barrier is minimized. Furthermore, the board layout should
be designed such that any coupling that does occur equally affects
all pins on a given component side. Failure to ensure this could
cause voltage differentials between pins exceeding the absolute
maximum ratings of the device, thereby leading to latch-up or
permanent damage.
PC BOARD LAYOUT
The ADM2490E isolated RS-485 transceiver requires no
external interface circuitry for the logic interfaces. Powersupply bypassing is required at the input and output supply pins
(Figure 24). Bypass capacitors are conveniently connected
between Pins 1 and 2 for VDD1 and between Pins 15 and 16 for
ISOLATION
BARRIER
VCC
SD103C
IN
VCC
22µF
OUT
ADP667
TRANSFORMER
DRIVER
5V
10µF
SET GND SHDN
78253
SD103C
VCC
VDD1
VDD2
GND2
Figure 25. Isolated Power-Supply Circuit
Rev. 0 | Page 15 of 16
05889-012
ADM2490E
GND1
VDD2
GND2
A
B
NC
Z
Y
GND2
05889-013
VDD2. The capacitor value should be between 0.01 μF and 0.1 μF.
The total lead length between both ends of the capacitor and
the input power-supply pin should not exceed 20 mm.
Bypassing between Pins 1 and 8 and between Pins 9 and 16
should also be considered unless the ground pair on each
package side is connected close to the package.
ISOLATED POWER-SUPPLY CIRCUIT
ADM2490E
OUTLINE DIMENSIONS
10.50 (0.4134)
10.10 (0.3976)
9
16
7.60 (0.2992)
7.40 (0.2913)
1.27 (0.0500)
BSC
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
10.65 (0.4193)
10.00 (0.3937)
8
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0197)
0.25 (0.0098)
2.65 (0.1043)
2.35 (0.0925)
SEATING
PLANE
45°
8°
0°
0.33 (0.0130)
0.20 (0.0079)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-013- AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
060606-A
1
Figure 26. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body
(RW-16)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model
ADM2490EBRWZ 1
ADM2490EBRWZ–REEL71
1
Temperature Range
−40°C to +105°C
−40°C to +105°C
Package Description
16-Lead Wide Body SOIC_W
16-Lead Wide Body SOIC_W
Z = Pb-free part.
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05889-0-10/06(0)
Rev. 0 | Page 16 of 16
Package Option
RW-16
RW-16