October 11, 2006 DR217-9 SERIES RADIAL LEADED INDUCTORS Features z z z z Designed for EMI Filters & Switching Power Supplies Inductance Range from 10µH to 10mH Operating Temp. -20°C to +80°C Tinned Leads with Leaded Solder is Available (note 5) ELECTRICAL SPECIFICATIONS AT 25ºC Part Number Inductance (µH) @1kHz DCR (Ohm) Max. Rated Current (A) Max. I sat Rated Current (A) Max. I rms DR217-9-103 DR217-9-153 DR217-9-223 DR217-9-333 DR217-9-473 DR217-9-683 DR217-9-104 DR217-9-154 DR217-9-224 DR217-9-334 DR217-9-474 DR217-9-684 DR217-9-105 DR217-9-155 DR217-9-225 DR217-9-335 DR217-9-475 DR217-9-685 DR217-9-106 10 ± 20% 15 ± 10% 22 ± 10% 33 ± 10% 47 ± 10% 68 ± 10% 100 ± 10% 150 ± 10% 220 ± 10% 330 ± 10% 470 ± 10% 680 ± 10% 1000 ± 10% 1500 ± 10% 2200 ± 10% 3300 ± 10% 4700 ± 10% 6800 ± 10% 10000 ± 10% 0.023 0.028 0.035 0.043 0.052 0.068 0.097 0.14 0.2 0.3 0.43 0.61 1.0 1.3 2.0 3.1 4.4 6.5 10 8 6.5 5.5 4.5 3.6 3.1 2.6 2.1 1.7 1.4 1.1 0.95 0.78 0.64 0.53 0.43 0.36 0.3 0.24 5.1 4.5 4.2 3.7 3.4 3.0 2.5 2.1 1.7 1.4 1.1 0.99 0.78 0.68 0.55 0.44 0.37 0.3 0.24 MECHANICAL SPECIFICATIONS XXX .039 MIN. 1,00 1 .630 MAX. 16,00 .590 MIN. 15,00 2 .295 ±.039 7,50 ±1,00 Ø .551 MAX. 14,00 Ø .031 TYP 0,80 1 2 SCHEMATIC NOTES: 1. Dimensions are shown in inches/millimeters 2. Unless otherwise specified, tolerance = Inches: ±0.012 = Millimeters: ±0,30 3. Isat based on the inductance being 90% of its initial value 4. Irms based on a temperature rise of 20°C 5. For non-RoHS parts replace DR prefix with 42- (e.g. DR217-9 becomes 42-217-9) 6. Terminal finish is compliant to RoHS requirements DATATRONIC: 28151 Highway 74, Romoland, CA 92585 Tel: 951-928-7700 Toll Free Tel: 888-889-5391 Fax: 951-928-7701 Email: [email protected] 499 King’s Road, Hong KongTel: (852) 2562 3858, (852) 2564 8477 Fax: (852) 2565 7214, (852) 2563 1290 All specifications are subject to change without notice.