DLE45/60 Series LED Drivers 45/60 Watts xxx Series • AC Input LED Driver • Constant Voltage/Constant Current Operation • Constant Current Dimming Versions • High Efficiency • Water Proof to IP67 • Class 2 • 3 Year Warranty The DLE series of AC input LED drivers incorporate universal input with active power factor correction in a two power stage design, eliminating flicker while providing a high efficiency solution. Designed as a class II isolation product, without the need for a safety earth, DLE series LED drivers are also approved as a class 2 limited power source, making them suitable for a wide range of applications. Dimmable constant current versions are available with the facility for PWM, voltage and resistance programming. Dimensions: DLE45/60: 6.73 x 1.78 x 1.27” (164.1 x 45.3 x 32.5 mm) Models & Ratings Constant Voltage / Constant Current Models Output Power 45 45 48 40 50 60 60 60 60 W W W W W W W W W Output Voltage 24 36 48 57 12 24 36 48 57 Output Current Output Voltage Range in Constant Current Mode 1850 mA 1250 mA 1000 mA 700 mA 4200 mA 2500 mA 1650 mA 1250 mA 1050 mA 16 - 24 V 24 - 36 V 34 - 48 V 40 - 57 V 9 - 12 V 16 - 24 V 24 - 36 V 34 - 48 V 40 - 57 V V V V V V V V V V OVP Range 26.4-31.2 39.6-46.8 52.8-62.4 62.9-70.0 13.2-15.6 26.4-31.2 39.6-46.8 52.8-62.4 62.9-70.0 V V V V V V V V V Efficiency(1) Model Number 85.0% 86.0% 87.0% 87.0% 86.0% 86.0% 87.0% 88.0% 88.0% DLE45PS24 DLE45PS36 DLE45PS48 DLE45PS57 DLE60PS12 DLE60PS24 DLE60PS36 DLE60PS48 DLE60PS57 Efficiency(1) Model Number 85.0% 86.0% 87.0% 87.0% 86.0% 86.0% 87.0% 88.0% 88.0% DLE45PS1850-AD DLE45PS1250-AD DLE45PS1000-AD DLE45PS700-AD DLE60PS4200-AD DLE60PS2500-AD DLE60PS1650-AD DLE60PS1250-AD DLE60PS1050-AD Models & Ratings Dimmable Models Output Power 45 45 48 40 50 60 60 60 60 W W W W W W W W W Output Voltage 24 36 48 57 12 24 36 48 57 Output Current Output Voltage Range in Constant Current Mode 1850 mA 1250 mA 1000 mA 700 mA 4200 mA 2500 mA 1650 mA 1250 mA 1050 mA 16 - 24 V 24 - 36 V 34 - 48 V 40 - 57 V 9 - 12 V 16 - 24 V 24 - 36 V 34 - 48 V 40 - 57 V V V V V V V V V V Notes 1. Typical efficiency at full load and 230 VAC input. 1 www.xppower.com OVP Range 26.4-31.2 39.6-46.8 52.8-62.4 62.9-70.0 13.2-15.6 26.4-31.2 39.6-46.8 52.8-62.4 62.9-70.0 V V V V V V V V V DLE Series LED Drivers Input Characteristic Minimum Input Voltage - Operating 90 Input Frequency 47 Typical Power Factor Maximum Units Notes & Conditions 305 VAC See derating curve 63 Hz >0.9 Measured at 230 VAC, full load 0.6 Input Current Inrush Current Input Protection 115 VAC A 0.3 230 VAC 230 VAC cold start, +25 ºC 45 A Maximum Units Notes & Conditions 57 VDC See models and ratings table 1.5 s Internal T1.0 A/250 V fuse fitted in line Output Characteristic Minimum Output Voltage 12 Typical Minimum Load No minimum load required Start Up Delay Hold Up Time 20 Measured at 115 VAC ms Line Regulation ±0.5 % ±1 Load Regulation Constant voltage mode % ±5 Turn On Overshoot 7 Constant voltage mode 4 % Deviation, recovery to within 1% in 10 ms for a 50% load change 200/250 mV pk-pk 105 % Transient Response Ripple & Noise Constant current mode % ≤24 V/>24 V. Measured using 12” twisted pair with 0.1 µF and 47 µF capacitors in parallel at 20 MHz bandwidth, at 25 °C Overvoltage Protection See models and ratings table, recycle AC to Reset Overload Protection 95 Auto Recovery Short Circuit Protection Trip & restart (hiccup mode) Temperature Coefficient 0.04 %/˚C Constant Current Curve Output Voltage Vo max Load Regulation in Constant Current Mode Vo min Trip & Restart Zone 0 10 20 30 40 50 60 70 Output Current (%) 80 90 100 General Characteristic Minimum Efficiency Isolation: Input to Output Switching Frequency Mean Time Between Failure Weight Typical Maximum 87 Units % 3750 Notes & Conditions See models and tables VAC 100 kHz >200 kHrs 0.9 (410) lb (kg) www.xppower.com MIL-HDBK-217F at 25 °C GB 2 DLE Series LED Drivers Environmental Characteristic Minimum Operating Temperature Operating Humidity Storage Temperature Maximum Units Notes & Conditions -20 Typical +50 °C See derating curve 5 100 % RH, non-condensing +80 °C Some specification parameters maybe exceeded until after 20 minutes warm up period. 3000 m -40 Operating Altitude Shock 30 g pk, half sine, 6 axes EN60068-2-27, -2-47 & MIL-STD-810F 514.5 cat 4 Vibration 10-500 Hz, 2 g, 10 mins/cycle, 6 cycles in each of axes Derating Curves 80 80 Load (%) 100 Load (%) 100 60 40 20 0 -20 60 40 20 -10 0 10 20 30 40 50 60 0 90 70 100 305 Temp (˚C) Input Voltage (VAC) EMC: Emissions Phenomenon Standard Test Level Conducted EN55015 Class B Radiated EN55015 Class B Harmonic Current EN61000-3-2 Class C Voltage Fluctuations EN61000-3-3 Criteria Notes & Conditions Notes & Conditions EMC: Immunity Phenomenon Standard Test Level Criteria Equipment for General Lighting Purposes EN61547 as below as below ESD Immunity EN61000-4-2 Radiated Immunity EN61000-4-3 EFT/Burst EN61000-4-4 2 A Surges EN61000-4-5 Installation class 3 A Conducted EN61000-4-6 2 A Magnetic Field EN61000-4-8 2 A Dips and Interruptions EN61000-4-11 A 2 8 kV air and 4 kV contact A Dip: 30%, 10 ms A Dip: 30%, 200 ms A/B At 230 VAC/100 VAC Int: 100%, 8.3 ms A/B At 230 VAC/100 VAC Safety Approvals 3 Safety Agency Safety Standard UL UL8750 Notes & Conditions TUV EN61347 CE CE Mark IEC IEC61347-2-13 used in conjunction with IEC61347-1 IP IEC60529 www.xppower.com DLE Series LED Drivers Mechanical Details Constant Voltage / Constant Current 6.46 (164.1) AC N (Blue) AC L (Brown) 0.13 (3.5) 0.13 (3.5) 1.78 (45.3) SJTW 18 AWG 2C 0.13 (3.5) 1.27 ±0.7 (150.0 ±20.0) R1.8 V+ (Red) UL 2464 18 AWG 2C 0.13 (3.5) V- (Black) 1.27 ±0.7 (150.0 ±20.0) 6.73 (171.1) 1.27 (32.5) Mechanical Details Dimmable Version 6.46 (164.1) 0.13 (3.5) SJTW 18AWG 2C 0.13 (3.5) 1.78 (45.3) AC N(Blue) AC L(Brown) 0.13 (3.5) 1.27 ±0.7 (150.0 ±20.0) R1.8 UL 2464 18AWG 4C 0.13 (3.5) V+ (Red) V- (Black) Dim+ (Blue) Dim- (White) 1.27 ±0.7 (150.0 ±20.0) 6.73 (171.1) 1.27 (32.5) Notes 1. Dimensions shown in inches (mm). 2. Weight: 2.8 lb (1.27 kg). 3.Tolerance: 0.X = ±0.008 (±0.2) 0.XX = ±0.002 (±0.05) www.xppower.com 4 DLE Series LED Drivers Output Current Adjustment by Variable Resistor V+ Dim+ Connect a variable resistor between Dim+ and Dim-. DLE Dim- The Dimmed output current can be determined using the equation: Dimmed Current = V- Maximum Current x R 100 k Where the value of R is between 10 kΩ and 100 kΩ. The corresponding range of output current is 10% to 100% Output Current Adjustment by DC Voltage V+ Dim+ Connect a variable voltage betwen Dim+ and Dim- + The dimmed output current is given by: DLE V- Dim- Dimmed Current = Maximum Current x V Where V is the value of control voltage in the range of 1.0 V to 10.0 VDC. The corresponding range of output current is 10% to 100%. 10 k Output Current Adjustment by PWM A Pulse Width Modulated (PWM) signal with duty cycle DPWM can be applied between Dim+ and Dim-. 10 V 0V PWM Dim+ Dim- DLE V+ V- GND Dimmed Current = Maximum Current x D Pwm % (Dpwm = PWM duty cycle) The dimmed output current is given by: Where Dpwm is the % of duty cycle between 10% and 100%. The corresponding range of output current is 10% to 100%. PWM frequency should be in the range 0.5 kHz to 5 kHz 5 www.xppower.com 06Feb14