CM1690 Praetorian™ L-C LCD and Camera EMI Filter Array with ESD Protection in Ultra-Thin uDFN Packages Features • • • • • • • • four, six and eight filters (C-L-C) in small form factor uDFN 0.40mm pitch packages. Each EMI filter channel of the CM1690 is implemented as a 3-pole L-C filter where the component values are 16pF-12nH-16pF. The CM1690's roll-off frequency at –6dB attenuation is 330MHz and can be used in applications where the data rates are as high as 140Mbps while providing greater than –35dB attenuation over the 1.0GHz to 3.0GHz frequency range. The parts include ESD diodes on every pin, which provide a very high level of protection for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The ESD protection diodes connected to the filter ports are designed and characterized to safely dissipate ESD strikes of ±15kV, beyond the maximum requirement of the IEC61000-4-2 international standard. Using the MIL-STD-883 (Method 3015) specification for Human Body Model (HBM) ESD, the pins are protected for contact discharges at greater than ±30kV. Four, six and eight channels of EMI filtering with integrated ESD protection Pi-style EMI filters in a capacitor-inductor-capacitor (C-L-C) network ±15kV ESD protection on each channel (IEC 61000-4-2 Level 4, contact discharge) ±30kV ESD protection on each channel (HBM) Greater than -35dB attenuation (typical) at 1GHz 0.5mm thick uDFN package with 0.40mm lead pitch: • 4-channel = 8-lead uDFN • 6-channel = 12-lead uDFN • 8-channel = 16-lead uDFN Tiny uDFN package size: • 8-lead: 1.70mm x 1.35mm • 12-lead: 2.50mm x 1.35mm • 16-lead: 3.30mm x 1.35mm Lead-free packaging This device is particularly well suited for wireless handsets, mobile LCD modules and PDAs because of its small package format and easy-to-use pin assignments. In particular, the CM1690 is ideal for EMI filtering and protecting data and control lines for the LCD display and camera interface in mobile handsets. Applications • • • LCD and camera data lines in mobile handsets Wireless handsets LCD and camera modules The CM1690 is available in space saving, ultra low profile 8-, 12-, and 16-lead 0.40mm uDFN packages with lead-free finishing. Product Description California Micro Devices’ CM1690 is a family of pi-style EMI filter arrays with ESD protection, which integrates Electrical Schematic 12nH FILTER+ESDn* FILTER+ESDn* 16pF 16pF GND 1 of 4, 6 or 8 EMI/RFI Filter Channels with Integrated ESD Protection * See Package/Pinout Diagram for expanded pin information. © 2007 California Micro Devices Corp. All rights reserved. 06/25/07 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.cmd.com 1 CM1690 PACKAGE / PINOUT DIAGRAMS TOP VIEW BOTTOM VIEW TOP VIEW (Pins Down View) 8 7 6 5 (Pins Up View) 1 2 3 4 (Pins Down View) PAD 1 CM1690-04DE 8-Lead uDFN Package TOP VIEW (Pins Down View) Notes: 1) These drawings are not to scale. 2 3 4 5 12 11 10 9 8 7 6 (Pins Up View) 1 2 3 4 5 6 7 8 GND PAD P908E 1 2 3 4 5 GND PAD CM1690-06DE 12-Lead uDFN Package BOTTOM VIEW 16 15 14 13 12 11 10 9 Pin 1 Marking 2 3 4 5 6 P906 Pin 1 Marking 8 7 6 5 1 2 3 4 (Pins Up View) 1 7 12 11 10 9 8 GND P9 Pin 1 Marking BOTTOM VIEW 6 7 8 16 15 14 13 12 11 10 9 CM1690-08DE 16-Lead uDFN Package PIN DESCRIPTIONS DEVICE PIN(s) DEVICE PIN(s) -04 -06 -08 NAME -04 -06 -08 NAME 1 1 1 FILTER1 Filter + ESD Channel 1 8 12 16 FILTER1 Filter + ESD Channel 1 2 2 2 FILTER2 Filter + ESD Channel 2 7 11 15 FILTER2 Filter + ESD Channel 2 3 3 3 FILTER3 Filter + ESD Channel 3 6 10 14 FILTER3 Filter + ESD Channel 3 4 4 FILTER4 Filter + ESD Channel 4 5 9 13 FILTER4 Filter + ESD Channel 4 5 5 FILTER5 Filter + ESD Channel 5 8 12 FILTER5 Filter + ESD Channel 5 7 4 6 GND PAD DESCRIPTION DESCRIPTION 6 FILTER6 Filter + ESD Channel 6 11 FILTER6 Filter + ESD Channel 6 7 FILTER7 Filter + ESD Channel 7 10 FILTER7 Filter + ESD Channel 7 8 FILTER8 Filter + ESD Channel 8 9 FILTER8 Filter + ESD Channel 8 GND Device Ground Ordering Information PART NUMBERING INFORMATION Lead-free Finish Pins Package Ordering Part Number1 8 uDFN-8 CM1690-04DE P9 12 uDFN-12 CM1690-06DE P906 16 uDFN-16 CM1690-08DE P908E Part Marking Note 1: Parts are shipped in Tape & Reel form unless otherwise specified. © 2007 California Micro Devices Corp. All rights reserved. 2 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.cmd.com 06/25/07 CM1690 Specifications ABSOLUTE MAXIMUM RATINGS PARAMETER RATING UNITS –65 to +150 °C Current per Inductor 30 mA DC Package Power Rating 500 mW RATING UNITS –40 to +85 °C Storage Temperature Range STANDARD OPERATING CONDITIONS PARAMETER Operating Temperature Range ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE1) SYMBOL PARAMETER L CONDITIONS MIN Channel Inductance TYP MAX 12 At 2.5VDC Reverse Bias, 1MHz, 30mVAC C Capacitance C1 At 2.5VDC Reverse Bias, 1MHz, 30mVAC 16.5 pF VDIODE Standoff Voltage IDIODE = 10μA 6.0 V ILEAK Diode Leakage Current (reverse bias) VDIODE = +3.3V 0.1 0.3 μA VSIG Signal Clamp Voltage Positive Clamp Negative Clamp ILOAD = 10mA ILOAD = –10mA 6.8 –0.8 9.0 –0.4 V V VESD In-system ESD Withstand Voltage a) Human Body Model, MIL-STD-883, Method 3015 b) Contact Discharge per IEC 61000-4-2 Level 4 RDYN fC 40 pF Notes 2, 3 and 4 ±30 kV ±15 kV Dynamic Resistance Positive Negative 2.3 0.9 Ω Roll-off Frequency at -6dB Attenuation ZSOURCE = 50Ω, ZLOAD = 50Ω 330 MHz RINSULATION Insulation Resistance RCHANNEL 5.6 –1.5 33 nH Total Channel Capacitance CTOTAL 25 UNITS VDIODE=3.3V, Note 4 ΜΩ 10 Channel Resistance Ω Ω 8 Note 1: TA=25°C unless otherwise specified. Note 2: ESD applied to input and output pins with respect to GND, one at a time. Note 3: Clamping voltage is measured at the opposite side of the EMI filter to the ESD pin (i.e. if ESD is applied to pin A1 then clamping voltage is measured at pin C1). Unused pins are left open. Note 4: These parameters are guaranteed by design and characterization. © 2007 California Micro Devices Corp. All rights reserved. 06/25/07 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.cmd.com 3 CM1690 Performance Information Capacitance (Normalized) Typical Diode Capacitance vs. Input Voltage DC Voltage Figure 1. Filter Capacitance vs. Input Voltage (normalized to capacitance at 2.5VDC and 25°C) Figure 2. Typical Performance Curve © 2007 California Micro Devices Corp. All rights reserved. 4 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.cmd.com 06/25/07 CM1690 Mechanical Details uDFN-08 Mechanical Specifications Mechanical Package Diagrams Dimensions for the CM1690 supplied in an 8-lead, 0.4mm pitch uDFN package are presented below. PACKAGE DIMENSIONS uDFN JEDEC No. MO-229C* Leads 8 8 7 6 5 Pin 1 Marking E Package D Dim. Millimeters Inches Min Nom Max Min Nom Max A 0.45 0.50 0.55 0.018 0.020 0.022 A1 0.00 0.02 0.05 0.000 0.001 0.002 A3 0.127 REF 1 2 3 4 TOP VIEW 0.005 REF b 0.15 0.20 0.25 0.006 0.008 0.010 D 1.60 1.70 1.80 0.063 0.067 0.071 D2 1.10 1.20 1.30 0.043 0.047 0.051 E 1.25 1.35 1.45 0.049 0.053 0.057 E2 0.30 0.40 0.50 0.012 0.016 0.020 0.10 C 0.08 C e 0.40 BSC A1 A3 SIDE VIEW A 0.016 BSC 8X K 0.20 L 0.15 # per tape and reel 0.008 0.25 0.35 0.006 0.10 0.010 0.014 3000 M CAB b e Pin 1 Locator Controlling dimension: millimeters 1 8 2 3 C0.2 GND PAD 7 6 E2 4 5 K * This package is compliant with JEDEC standard MO-229C with the exception of the D, D2, E, E2, K and L dimensions as called out in the table above. D2 L BOTTOM VIEW Dimensions for 8-Lead, 0.4mm pitch uDFN package © 2007 California Micro Devices Corp. All rights reserved. 06/25/07 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.cmd.com 5 CM1690 Mechanical Details (cont’d) uDFN-12 Mechanical Specifications Mechanical Package Diagrams Dimensions for the CM1690 supplied in a 12-lead, 0.4mm pitch uDFN package are presented below. PACKAGE DIMENSIONS uDFN JEDEC No. MO-229C* Leads 12 12 11 10 9 8 7 Pin 1 Marking E Package D Millimeters Dim. Inches Min Nom Max Min Nom Max A 0.45 0.50 0.55 0.018 0.020 0.022 A1 0.00 0.02 0.05 0.000 0.001 0.002 A3 0.127 REF 1 2 3 4 5 6 TOP VIEW 0.005 REF b 0.15 0.20 0.25 0.006 0.008 0.010 D 2.40 2.50 2.60 0.094 0.098 0.102 D2 1.90 2.00 2.10 0.075 0.079 0.083 E 1.25 1.35 1.45 0.049 0.053 0.057 E2 0.30 0.40 0.50 0.012 0.016 0.020 0.10 C 0.08 C e 0.40 BSC A1 A3 SIDE VIEW A 0.016 BSC 12X K 0.20 L 0.15 # per tape and reel 0.008 0.25 0.35 0.006 0.10 e 0.010 M CAB b 0.014 Pin 1 Locator 3000 1 2 3 4 C0.1 GND PAD 12 11 10 Controlling dimension: millimeters 5 9 E2 6 8 7 K D2 * This package is compliant with JEDEC standard MO-229C with the exception of the D, D2, E, E2, K and L dimensions as called out in the table above. L BOTTOM VIEW Dimensions for 12-Lead, 0.4mm pitch uDFN package © 2007 California Micro Devices Corp. All rights reserved. 6 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.cmd.com 06/25/07 CM1690 Mechanical Details (cont’d) uDFN-16 Mechanical Specifications Mechanical Package Diagrams Dimensions for the CM1690 supplied in a 16-lead, 0.4mm pitch uDFN package are presented below. PACKAGE DIMENSIONS uDFN JEDEC No. MO-229C* Leads 16 Pin 1 Marking E Package D 16 15 14 13 12 11 10 9 Dim. Millimeters Inches Min Nom Max Min Nom Max A 0.45 0.50 0.55 0.018 0.020 0.022 A1 0.00 0.02 0.05 0.000 0.001 0.002 A3 0.127 REF 1 2 3 4 5 6 7 8 TOP VIEW 0.005 REF b 0.15 0.20 0.25 0.006 0.008 0.010 D 3.20 3.30 3.40 0.126 0.130 0.134 D2 2.70 2.80 2.90 0.106 0.110 0.114 E 1.25 1.35 1.45 0.049 0.053 0.057 E2 0.30 0.40 0.50 0.012 0.016 0.020 0.10 C 0.08 C e 0.40 BSC A1 A3 SIDE VIEW A 0.016 BSC 16X K 0.20 L 0.15 # per tape and reel 0.008 0.25 0.35 0.006 0.10 e 0.010 M CAB b 0.014 Pin 1 Locator 3000 1 2 3 7 8 16 15 14 13 12 11 10 9 C0.2 Controlling dimension: millimeters 4 5 6 E2 GND PAD K D2 * This package is compliant with JEDEC standard MO-229C with the exception of the D, D2, E, E2, K and L dimensions as called out in the table above. L BOTTOM VIEW Dimensions for 16-Lead, 0.4mm pitch uDFN package © 2007 California Micro Devices Corp. All rights reserved. 06/25/07 490 N. McCarthy Blvd., Milpitas, CA 95035-5112 ● Tel: 408.263.3214 ● Fax: 408.263.7846 ● www.cmd.com 7